Search Documents

By Lawrence W. Gubbe

Air blast associated with detonation of explosives in mining, construction or military applications is often responsible for complaints by people who live or work in the vicinity of the activity. Most often, the complaints are based on the perception that vibration caused by the airblast damaged one or more residential buildings that may be located within several hundred feet or several miles from the blast site. The potential for airblast to cause damage is related to the amplitude and frequency of the airblast overpressure wave at the receptor. Amplitude and frequency of the overpressure wave are, in turn, dependent upon the type and amount of explosive detonated; the degree of confinement; the distance the wave travels; the topography between the blast site and the receptor; and, atmospheric conditions. It is well known that, as the result of atmospheric focusing, the amplitude of airblast overpressure that exists relatively far from the blast site may be substantially higher than the amplitude associated with the attenuated wave in an isotropic atmosphere. Two methods are available to predict baseline overpressures 1) the Sandia Laboratories, Atomic Energy Commission method as extended by the Naval Ordinance Laboratory (NOL method) and the Ballistic Research Laboratory method (BRL method). These methods are developed by different techniques, are based on different idealized atmospheres and predict widely different results. The amplification factor applied to account for the effect of focusing must be consistent with the method used to predict the baseline overpressure. Theoretically, the amplitude of the overpressure at distances several miles from the blast site could be more than 25 to 100 times the amplitude of the attenuated wave predicted by the BRL method. However, based on comparisons with measured overpressure data is probably less than approximately 3 times the amplitude of the attenuated wave as predicted by the NOL method. This paper is based on research conducted as part of investigations of airblast damage complaints associated with an accidental explosion near Eveleth, Minnesota and with the disposal of military explosives by detonation at the Sierra Army Depot near Herlong, California. The techniques available for estimating the airblast overpressure that might be generated at various distances from the blast site and criteria for evaluating the potential for damage are examined.

Jan 1, 2004

By Brian Micke, Mick Gavrilovic

The problem of rock hang-ups in underground mining operations has been a continuing one since the days of the “hang-up man”. This position commanded the highest pay of any underground worker in many historical Western U.S. underground bulk-mining operations, due to the occupational hazards of the job. Although underground mining techniques and especially work practices have changed greatly since then, the hang-up problem is a continuing one in many mines which use gravity flow of coarse rock in their transport systems or in those mines where stressed ground causes rock slabs to spa11 and bridge rock passes and stopes. In addition, with mechanized underground open-stoping mining methods now being used in many different types of ore deposits worldwide, this problem has again emerged as a very significant one in many of these highly mechanized operations. This is especially so where the remote operation of loaders is used for removing blasted rock from underground open stopes.

Jan 1, 1999

In all the industries that require blasting operations using explosives, there exists numerous unwanted side effects of the blast which may pose as environmental hazards. These hazards face prominence, especially in India, where there are very stringent rules and regulations governing the use of explosives. The environmental hazards associated with blasting operations as a whole can be tacked successfully to a certain extent depending upon the ultimate expectations of ,the post-blast effects and the limitations of the environmental obligations as specified by the authorities from time to time and from place to place. The main parameters which require attention to limit the post-blast results to the optimum level are ground vibrations, dust pollution, gas pollution, air blast effects, noise pollution & fly rocks etc.

Jan 1, 1995

By Douglas A. Anderson

Much progress has been made in understanding the forward process for blast vibration simulation: that is, how to create a resultant seismogram from an empirically determined seed waveform. What has not been successfully investigated to date is the reverse process: Determining the contribution of each borehole to the resultant seismogram. It might seem that these should be two sides of the same coin, but the reverse process is much more complicated. That is because the source, geological path, and receiver contributions must be unraveled and then dissected. If that can be done, a relationship can be developed between the seismic source properties and the explosive interaction with the surrounding rock. This paper presents a first step in the unraveling process, through analysis of blast seismograms using wavelet transforms.

Jan 1, 2013

By Gregory B. Poole

As part of a $3.5 billion program to improve the antiquated waste water system in the city of Atlanta, the Nancy Creek Tunnel is being constructed across the northwest portion of the city. This tunnel is over eight miles long and is being constructed using Tunnel Boring Machines (TBM) for the majority of the tunnel and conventional drilling and blasting for three shafts, starter and tail tunnels and four connecting tunnels, totaling 2400 feet in length. An extensive public relations program was developed for this project. A group effort by the owner, engineer and contractor produced a public relations program that both informed and educated the public of the anticipated perceptions and effects of the blasting and TBM activities.

Jan 1, 2005

By David G. Borg

"Although researchers have realized varying degrees of success in numerics modeling, computer blast simulations and small scale in-situ testing, most will agree that the greatest uncertainty in total success stems from the uncontrollable field variables. Given the diverse nature of field conditiorencountered, no reliable and proven method of evaluating fragmentation quantitatively, and the lack of adequate field controls found in many operations, it is unlikely that a universal plug-in model will be developed for all blasting in the imediate future. This does not imply that all research devoted to modeling should cease, for it is precisely here where more research efforts are desperately needed."

Jan 1, 1989

A series of stemming confinement tests were conducted at a test site near Vernal, Utah. The purpose of the study was to determine the relative performance of various stemming enhancement “plugs”, stem types and loading configurations. The stemming performance was quantified in terms of: . Stem confinement time . Stem ejection velocity . Ground swell velocity . Ground vibration . Air blast . Crater formation Of primary interest was the performance of a new spherical stemming enhancement plug. The initial findings indicate that the hard plastic spheres improved blast performance when used appropriately. Their ability to improve blast performance is reduced when used in over confined or severely underconfined conditions. The study also evaluated the effects of air decking on stemming confinement and explosive performance.

Jan 1, 2000

By Steven Putt

Seismic While Drilling (SWD) is a newly developed technology in the mining industry. Improving upon Measurement While Drilling (MWD) systems, SWD measures mechanical properties of the rock at incremental depths down a blast hole at a much higher resolution. SWD is also immune to common failures and inconsistencies of MWD such as operator and drill specific variation. Seismic While Drilling records the velocity and elastic modulus of the rock with centimeter accuracy in real-time. These properties measured while drilling blastholes are then used as a proxy for density which can be used for: • High resolution geologic modeling • 3D ore control • Drill and blast optimization • Drill to mill tracking One of the distinct challenges with SWD systems is the sheer volume of information acquired. With thousands of measurements per blasthole, the data can be overwhelming for even an experienced engineer. To overcome this complex challenge, the latest cloud computing and analytics models have been simplifying and organizing the data. These newer technologies can amplify an engineer’s capability by delivering actionable insights into their drilling and blasting workflows. The paper presents new results from Datacloud during recent Seismic While Drilling trials in iron ore, metallurgical coal, and hard rock mines around the world. The measurements are compared with wireline geophysical logs, core data, drill cuttings, and conventional measurement while drilling (MWD) systems to validate the technology and show how the data can be used.

By Michael Ostrowski

While the words “explosives” and “blasting” cause insurers to become apprehensive, skilled contractors using modern techniques under controlled conditions rarely cause serious damage or injury. However, blasting operations frequently result in complaints and, consequently, insurance claims. The purpose of this bulletin is to inform construction project participants of some of the measures which may be taken to reduce losses arising from blasting operations.

Jan 1, 2003

By Kate Satish

M/s Konkan Railways Corporation are constructing 760 kms long rail road in the Western Coastal Region of India. The rail road encounters 75 tunnels through the Western Ghats of India with a total length of 78.35 kms, the longest tunnel being 6.5 kms long. The tunnels are of horse shoes shape having a cross section of about 37 Sq.meters

Jan 1, 1996

By Paul Kunze

When a new bridge was needed across the upper reaches of the Yellowstone River in Montana, removing the old concrete bridge piers became an environmental concern for the highway department engineers. The location is about fifty miles downstream from the north edge of Yellowstone Park. The determination was made by the federal and state agencies charged with protecting the resource, that the old piers had to go but the river bed had to remain unchanged. Concerns were expressed that removing the concrete presented the potential for environmental damage to this protected portion of the river. These concerns prompted the state to place stringent restrictions on the contractor in the way they carried out the demolition and disposal of the piers. The reinforced concrete masses had to be removed to an elevation at least fifteen feet below the river bed and every bit of concrete debris had to be removed from the river channel. Explosive removal was discouraged, but the only other options: saw cutting, mechanical or chemical breaking, were not viable.

Jan 1, 2014

By Laura Bastemante, Bruce Vandenberg, Fred Huettig

Recent advances in solid-state, field portable, fast framing video camera systems and PC based frame capture hardware now allow blast imaging up to loo0 frames per second. Up to 8 seconds of data can be stored directly into the unit, downloaded to a PC or archived to a standard VCR without data compression. Since no film processing is involved, motion analysis can be performed instantly and on-site within a few minutes. This paper will describe the design features and applications of the KineView 1256P system and compare these with the analogous aspects of film based cameras.

Jan 1, 1997

By Vitor Fonseca de Barcelos, Jair Carlos Koppe

Our society is experiencing a digital revolution. Technology is demonstrating its significant potential for mining industry. In this paper are presented the measured and estimated impacts of applying new technologies on blasting operations in a copper mine.

Feb 1, 2020

By John E. Wiegand

"We will attempt to explain the basic workings of a modern seismograph and how the recorded data can be interpreted, not only for determining compliance to the regulations, but also in determining whether or not a seismograph record is accurate and valid. We will discuss some parameters that should be included in all seismographic recordings. We will give examples and use overhead slidesto show examples of both accurate and valid recordings, and tampered and inaccurate seismograph recordings. Much of the information presented will be basic in nature, and will reflect the opinions and personal experiences of the author. We ho'pe the listener will gain valuable information concerning the use and interpretation of seismographic data, as well as find interest and sometimes humor in the examples shown."

Jan 1, 1992

By Randall M. Wheeler

The measurement and analysis of blast-induced ground vibrations are more complex than ever before. This is primarily due to the advancements made in microchip technology, mass storage utilities and the computer, which have allowed us to reduce and analyze data in a matter of moments instead of days. Terminologies such as Fourier transform, response spectra, cross-correlation, convolution, deconvolution and half-length frequency, etc. mean little to anyone except those who are experts in the field. A little understanding of the basic concepts behind vibration effects can help a beleaguered end-user feel more confident about what their measurements really mean.

Jan 1, 1992

By Steve Dillingham

There are some blasters and blasting companies that just seem to have better safety reputations than others. This is in spite of the fact that they are essentially doing the same type of work under similar conditions. To achieve that enviable safety reputation, it simply comes down to a strong safety culture prompted by a responsibility for others, as well as yourself and your company.

Jan 1, 2003

By Roberto Folchi, Hans Wallin

Having so many norms and technical content of legislation to deal with is a problem that an explo-sives engineer has to face, especially when working at an international level. Each country has its own norms and legislation, sometimes even each other region or state, as if the physics of explo-sions, rock, concrete, and masonry characteristics would change across the borders. Both norms and laws are frequently out of date, being mainly developed at the beginning of the previous century and adjusted, piece by piece, to a technical and political context that is constantly changing, with adjustment being frequently adopted in a hurry, due to a problem arising such as that of internation-al terrorism. Sometime also, norms are not harmonized with those they intend to amend, so required explanations and new adjustments lead to a vicious circle that increases confusion, complexity and depresses the explosive industry.

Jan 1, 2015

By Jeon Jeon, Yong-Kun Choi, Chung-In Lee, Yong-Hun Jong, Hag-Soo Kim

In this study, a computer program to design tunnel blasting pattern has been developed. The program consists of two parts; one is for tunnel blasting pattern design and the other is for blasting modeling to estimate the peak particle velocity, the distribution of fragmentation and the excavation damage zone. We modified the design method of tunnel blasting pattern suggested by Langefors because it provided undesirable pattern in blasting practices such as considerably large center cut and too large burden for Vcut as drilling length increased. As a result, the burden and spacing were reduced to practically appropriate amounts. In addition, the correlation between rock mass rate, RMR, and rock constant in blasting, c, was analyzed based on the data collected from twenty three tests of tunnel blasting. It was concluded that the correlation between them was fairly good enough to be applied in cut design. In order to check the validity of the modified methods and their practical applicability, test blasting was carried out at two different tunnel construction sites in Korea. The results were satisfactory in that the average rate of advance was 90% and the overbreak did not cause additional support. Futhermore, the developed program is capable of estimating peak particle velocity by using (a) the existing vibration equations, (b) the vibration equation obtained by test blasting to check out the practical applicability of the designed blasting pattern. Feedback is implemented into the program to adjust the designed blasting pattern and control the vibration.

Jan 1, 2005

By Patrice Favreau, R. F. Ph. D. Professor Emeritus Favreau

After Nobel invented dynamite, blasts were carried out by trial and error, without the use of equations based on the fundamental principles of Chemistry and Physics, although everyone accepted that shock waves were involved; but no equations were available to calculate their intensity. Around 1950 however, M.A. Cook proposed a procedure to calculate the thermochemistry of an explosive, and thus evaluate theenergy released during the explosion of a fully confined explosive. Some blasters then began to use theEnergy Factor; the latter, however, does not subdivide the energy into its three kinds of activities necessaryfor a successful blast, as demonstrated in 1968 by reference 2, namely i) the shock wave which weakensthe rock; ii) the stress field SS which fully fragments the rock; and iii) the release of the stress SS whichcauses the fully fragmented rock to burst out with the velocity necessary to move the rock into the muckpile. The article explains that the way to achieve a successful blast is by insuring that the explosive energy divides properly into the weakening action of the shock wave which is necessary to prevent large collar blocks and toe, and into adequate stress field intensity SS which is necessary to obtain good fragmentation size distribution at the crusher, as well as adequate burst out rock movement to achieve easy mucking.

By M. Hagfors

When establishing an underwater testing site for the energy measurements of the explosives, the dimensions of the measuring pool have to be measured to find out what is the maximum weight for the test charge. Secondly one has to decide the distance between the pressure gauge and the shooting point. Thirdly the pool has to be calibrated because of the reflections of the explosions by measuring the bubble periods of the calibration charges. The calibration shots can also be used to estimate the minimum weight of the explosive charge for the reliable energy measurements by calculating the shock, gas heave and total energy values and their standard deviations.

Jan 1, 2007