Search Documents

By A. Gül

This investigation was carried out with low grade Murgul-Cakmakkaya copper ore once used to be dumped away as waste material. Sulphide minerals in the ore sample observed are chalcopyrite, pyrite, sphalerite and to some extent molibdenite; quartz, calcite and dolomite are the gangue minerals. The ore sample assays 0.28% Cu, 2.94% Fe and 3.36% S. Mineralogical study of the ore sample showed that adequate liberation of chalcopyrite for flota-tion was achieved below 100 µm. In flotation tests Aerophine 3418-A was the collector employed, NaOH or Ca(OH)2were the pH modifiers. Deactivators used were sodium meta bi-sulphide, starch, dextrin and lime. MIBC was the frother used throughout the tests. Test results showed that starch alone was the most suitable depressant to give the optimum metal content and recovery val-ues. Activated charcoal was used to adsorb excess collector species in the flotation pulp during cleaning stages After two stages cleaning of the rougher concentrate using starch as the depressant a copper concentrate assaying 21.2% Cu was obtained with 79.5% recovery while the tailings contained 0.01% Cu and metal losses were about 3%

Jan 1, 2014

By Teemu Väyrynen, Matti Vilkko, Antti Jaatinen, Pekka Itävuo

"This paper shows that smooth and accurate feed-hopper level control is essential for consistent cone crusher operation. The objective of the paper is to define the best practices for tight control of cone crusher feed-hopper level. The paper discusses the challenges involved in a delay-dominant level control problem (specifically, dead-time-induced performance and stability issues, mass flow disturbances, process and actuator non-linearity) and proposes five corresponding control structures. The performance of the proposed control structure candidates is evaluated in a simulation study and, finally, a full-scale experiment is conducted for the best-performing candidate. The results of this study emphasize the importance of control structure selection. While the most obvious control structures failed to deliver the desired performance, the best result was achieved by using control structures that eliminate the conveyor transport delay (dead-time) from the control loop. In practice, the control loop dead-time can be eliminated by either using an actuator (variable-speed feed conveyor) that is connected directly to the feed-hopper, or by redefining the process boundaries closer to the used actuator (regulate the circuit mass balance instead of feed-hopper level). The presented control structures provide means to achieve a consistent cone crusher performance and size reduction. This facilitates efforts to improve the plant’s performance and increases the plant’s overall stability."

Jan 1, 2014

Cyanide is reactive to copper minerals and is not suitable to extract the gold from the copper bearing ores. Ammoniacal thiosulfate is considered an excellent alternative lixiviant for leaching copper bearing gold ores. Unfortunately the results of high reagent consumption and poor gold ex-traction were found by thiosulfate leaching of synthetic gold ores containing chalcopyrite, chalcocite or bornite and a mild refractory copper-bearing sulfidic gold ore. In this investigation, several processes have been applied to reduce the impacts of these minerals on gold leaching. The process included: the pre-oxidation of copper sulphide minerals in water or ammonia solution, the reduction of dissolved oxygen in the lixiviant (0.3 ppm DO or 0.7% oxygen), adding phosphate anion in the leach or pre-leach stage, and the addition of a strong copper ligand (e.g., EDA and DETA). The results indicated that the gold extraction could be improved to 93% with the thiosulfate consumption being reduced to less than 8 kg/t. The dissolution of copper minerals was found to be the major reason for increased consumption of thiosulfate and the highly reductive leached surfaces are responsible for the reduced gold extractions.

Jan 1, 2014

By James A. Finch

"Developed countries are in the midst of re-structuring education in minerals-related disciplines as raw materials, once vital to wealth generation, contribute progressively less to the economy. The changing circumstances mean institutions must justify mineral processing by new criteria. After considering what a mineral processor needs to know the ways to deliver are considered. Taking twenty graduates per year to illustrate, one institute could justify this number as a program in a department or school (of whatever grouping of disciplines). A strong research component would make the package additionally attractive. Divide among four institutions and mineral processing is best served in a research centre with delivery taking advantage of multi-centre and distance learning opportunities.INTRODUCTIONThis is one of five plenary lectures at the Congress. I may have preferred a technical subject, as that is what occupies most of my thinking hours, but it is reasonable as an academic that this topic should come to one of us. The fact the topic has not been high on my agenda may provide one advantage: that I can suggest directions free of pre-conceived notions, just as when reviewing the background to a technical article the temptation to select in support of one?s interpretations is resisted. The trick will be to add something new.One reading of the title seems to query whether mineral processing education has a future. (I will refrain at this juncture from defining mineral processing and assume for now we share an understanding of the term.) The proximity of natural and human resources led to the Industrial Revolution and the interaction continues to stimulate and sustain industrial and economic development in many parts of the world. The search for raw materials has historically played a key role in opening frontier areas, with undersea and outer space next. The reason is obvious: raw materials along with food and energy underpin society. Thus mining will remain part of human activity along with the need to pass on the knowledge and skills.What happens over time is resource relocation. Raw materials become exhausted in one area to be replaced by sources elsewhere; the demand for some materials lessens while growing for others. Educational institutions can find themselves with the wrong geography or with staff focussing on the wrong subjects. When this happens the restructuring produces much discussion. This is where we are in parts of the world. Japan, Western Europe and the United States are the prominent examples (Dowd, 1998; Flemings and Suresh, 2001; McDivitt, 2002). Mineral processing is becoming a series of courses in related disciplines: resource engineering, environment engineering or materials engineering. The start of the transition is evident in Canada and Australia, perhaps earlier than expected given the contribution of raw materials to their economies. A common backdrop in the developed countries is social pressure to reduce the impact of the ?untidy? aspects of life, and that includes mining. (This is not new: in classical times the mine face was the preserve of slaves and convicts.) These values are exportable, potentially affecting recruitment into mining schools everywhere."

Jan 1, 2003

By Thomas Mütze, Petya Atanasova, Kai Bachmann, Urs A. Peuker, Thomas Leißner

"A method is presented for the evaluation of mineral processing by liberation and upgrading. The method bases on the plot of recovery of valuables versus the recovery of gangue (Fuerstenau upgrading curve). The locking curve of a feed material was plotted together with the upgrading curve in a Fuerstenau diagram. The assessment of liberation and upgrading is done by a comparison of surfaces formed by the curves and some characteristic lines of the diagram. This plot allows the calculation of two new quantitative measures for liberation and upgrading. Both parameters can be combined to a third parameter describing the quality of the whole technical setup for mineral processing by subtracting the upgrading parameter from the liberation parameter. The third parameter shows a positive value in cases of upgrading determined processes, a negative value in cases of liberation affected processes and about zero for processes affected equally by liberation and upgrading. Thus it is easily possible to distinguish between poor results in the mineral processing caused by insufficient liberation or poor results caused by insufficient upgrading. Preliminary results from two case studies, performed on two different ore types, are very promising illustrating the practical use of such an approach."

Jan 1, 2014

By F. S. Niu

With the feature of finely-dissemination particle and complex mineral composition, oolitic hematite is considered to be the ore dressing difficult problem in the world. Series research on refractory oolitic hematite in Zhangjiakou Area are introduced as following: ore properties?technology mineralogy and mineral processing technology. The survey shows: with the fine grinding of the hematite to a fineness of -0.076mm 95%, obtaining iron concentrates grading 62.74% Fe at the recovery of 46.80% by high intensity magnetic separation- reverse flotation flowsheet; under the three stages intensity magnetic separation,four stages grinding and four stages gravity separation, getting the iron concentrates grading 61.09% Fe at the recovery of 45% using high intensity magnetic separation- gravity separation flowsheet; with roasting temperature of 800°C, time for 75~90min and ore-coal ratio of 11, gaining the iron concentrates assaying 62.74% Fe at the recovery of 87% by roasting- magnetic separation flowsheet. At present, this research is still doing for the target of raising the concentration recovery on the base of high grade concentrate. It is in the hope of fully utilizing the existing hematite resources in Zhangjiakou

Jan 1, 2014

By V. Panayotov, M. Panayotova

"Wastewater from ores processing is often polluted by molybdate and sulfate (SO42-) ions. Sorption is one of suitable methods for removing those pollutants when presenting in low concentrations. This work reports results on adsorption of sulfate and molybdate ions on metal modified (with barium - Ba and lead - Pb) and organic reagent modified (with Hexadecyl-trimethyl-ammonium bromide - HDTMA) clinoptilolite. Zeolite’s modification with Pb, Ba and HDTMA increases its uptake capacity with respect to Mo(VI) at pH 3, with the uptake capacity decreasing in the order CL-Pb > CL-HDTMA > CL-Ba. Lead-modified clinoptilolite shows high uptake with respect to Mo(VI) in acidic, neutral and slightly alkaline conditions. The presence of SO42- in concentrations twice higher than the amount of Mo(VI) do not interfere with the Mo(VI) removal by CL-Pb. Zeolite’s modification with Ba and Pb renders it able to immobilize SO42- from water in the pH range 3-9. Kinetics of the uptake process is best described by the pseudo-first order kinetic equation. Increasing the initial concentrations of Mo(VI) and SO42- increases the removed amount of pollutants. INTRODUCTION Wastewater from copper-molybdenum ores processing is often polluted by molybdate and sulfate ions. Molybdenum (Mo) migrates easily in water and consequently the Mo polluted areas could extend for hundreds and thousands of meters (Ryzhenko, 2010). Molybdate anion is the only Mo(VI) species in natural water, i.e. at pH > 6.0. Its median freshwater hazardous concentration affecting 5% of the species (HC 5.50%) is 38.2 mg Mo/L (De-Schamphelaere et al., 2010). The marine water chronic toxicity (HC 5.50%) is assessed at 5.74 mg Mo/L (Heijerick et al., 2012). The predicted no-effect concentrations (PNEC) are 12.7 mg Mo/L and 1.92 mg Mo/L correspondingly for freshwater and marine water (Heijerick et al., 2012a). When sulfates present in drinking water in excess of 250 mg/L they cause a cathartic action (especially in children) in the presence of sodium and magnesium, and when the concentration exceeds 600 mg/L, diarrhea. When sulfate-rich effluents are discharged into the environment, they may increase the acidity of water bodies and soils (Guimarães and Leão, 2014). Because of the adverse effects to human health and the environment, limits are set for SO42- concentrations in waters and wastewaters in the range of 250 / 500 mg/L."

Jan 1, 2018

By J. Langwaldt

Ammonium-nitrate is a main component in blasting agents and dissolved ammonium residues may be discharged with mine water. The European Union aims to reach a good state of the water quality and recommends ammonium content below 0.5 mg/L for drinking water. Natural zeolites adsorb ammonium from water. In this work, the removal of low-concentration ammonium by commercial natural zeolites was studied in continuous tests. Natural zeolites made up between 83% and 95% of the mineral composition. The major zeolite minerals were chabazite and clinoptiolites and minor amounts of erionite and mordenite were as well present. The five natural zeolite samples, 500~710 µm, were conditioned to obtain zeolites in the Na-form. Ammonium adsorption onto natural zeolites depends mainly on the zeolite mineral type. The chabazite containing zeolite was superior over the four clinoptiolite samples for the removal of low concentrations of ammonium from water (pH of 7.5, flow 5 mL/min, room temperature). The adsorption capacity of chabazite was 48.3 mg NH4+/g zeolites, i.e. 73% of the theoretical exchange capacity 69 mg NH4+/g, during duration over 107 days and almost 6700 bed volumes exchanged. The four tested clinoptiolites had an ad-sorption capacity of 15.7mg to 25.0 mg NH4+/g zeolites. The natural zeolites were rapidly regenerated by an alkaline sodium chloride solution fed to the columns.

Jan 1, 2014

By H. L. Liu

With the exploitation of mineral resources, valuable minerals are more and more finer and poorer. Priority reclaiming liberation grind particle under rough grinding, will help to pervert loss of melts, raise dewatering efficiency of concentrate, reduce consumption of reagent. And it is propitious to reduce energy consumption and raise the utilization rate of resources. With the feature of coarse particle?s desorption and deposition, CLF flotation machine has special pulp circulating way, which is not only apply to treat coarse particle but also normal size particle. The paper advanced the history, the design principle, the structure feature and the application of CLF flotation machine.

Jan 1, 2014

By A. Singh, M. Ntlhane, V. Ross, M. Dlame

"Fine valuable particles are often lost to flotation tailings streams due to inefficient collection by air bubbles as well as passivation of surfaces by oxidation and slimes. The application of high-shear hydrodynamic cavitation devices (HCDs) to overcome this problem has already proven to be a considerable success in the industry. This paper details the results of further investigations that were undertaken at Mintek to better understand the mechanisms involved when preconditioning feed slurries in an HCD. By promoting inter-particle attrition and conditions of high shear within the reactor, cleaning of particle surfaces is enhanced as well as the formation of superfine (nano) bubbles which are believed to aid their agglomeration and subsequent collection by normal sized bubbles. In order to broaden the envelope of understanding with regard to application of the technology, rather than tailings material as investigated earlier, a Platinum Group Mineral (PGM) UG2 ore from the Bushveld Complex in South Africa was used in this study. The results of a series of batch flotation tests in a 10L Denver cell are presented, being conducted after the feed has been subjected to different methods of preconditioning. It was demonstrated that the preconditioning significantly improved the flotation kinetics of the PGMs, the optimum being obtained after around 20 passes through the reactor. This was accompanied by a much enhanced recovery-mass pull relationship and a significant improvement in the grade-recovery response. Significantly, the selectivity between the PGM and the deleterious chromite (expressed as Cr2O3) gangue more than doubled under these conditions. Modelling of the PGM data by means of the modified Kelsall model indicated that both the fast and slow floating rate constants were improved.INTRODUCTIONIt is well known that the flotation recovery of fine and ultrafine particles, typically less than 10 micron in size, is a challenge (Yoon et al., 1989; Miettenin et al., 2010). Although these particles are typically well liberated, due to their very low mass and inertia, the collision efficiency with air bubbles is low as a result of the inability of particles to penetrate the liquid streamlines around bubbles. Hence the probability of contact is often regarded as the ratedetermining step in flotation of ultrafine particles. Introducing more power into conventional flotation machines is likely to solve only part of the problem, as conventional mechanisms are effective only to a point in terms of shear and micro-turbulence. Further challenges are posed by the treatment of low-grade or oxidised tailings dump material, where valuables are passivated due to prolonged exposure to the atmosphere or slimes. Over the years, various mitigating strategies have been investigated, including the use of dissolved air flotation (Martinez-Gomez et al., 2013; Calgaroto et al., 2015), shear flocculation (Subrahmanyam and Forssberg, 1990), seed or carrier flotation (Tabosa and Rubio, 2010), sonication to clean particle surfaces (Aldrich and Feng, 1999; Newell et al., 2006), high intensity conditioning (Bulatovic and Salter, 1989; Chen et al., 1999; Tabosa and Rubio, 2010), and various electrochemical approaches such as changing Eh in order to promote formation of dixanthogen, dissolution of oxidation products by lowering the pH, activation by sulphidisation (Newell et al., 2006; Becker et al., 2014), and the use of alternative collectors."

Jan 1, 2018

By Zhu Yangge, Hu Xiaoxing, Feng Qiming, Zhang Guofan, Zhang Xingrong

"During the flotation process of ilmenite and titanaugite with fatty acid as collector, unavoidable ions such as Ca2+, Mg2+, Al3+, Fe3+ and Fe2+ demonstrate considerable influence on the floatability of the minerals. In this study, flotation test, zeta potential test, and solution chemistry calculation were adopted to investigate the mechanism of how these metal ions affect the floatability of ilmenite and titanaugite in different pH conditions. The results show that in weak acidic solution, Ca2+ and Mg2+ mainly freely exist in the solution with little adsorption on mineral surface, and their reaction ability with oleate ions is weaker than active site on ilmenite surface (Fe), thus they show negligible effect on the flotation of ilmenite; Al3+ shows similar reaction ability with oleate ion compared to Fe3+, which lead to competitive reaction with collector, so the flotation of ilmenite is depressed. While Fe3+ can adsorb on surface of titanaugite in the form of Fe(OH)3, and it shows stronger reaction ability with oleate ion compared with active site on titanaugite surface (Ca and Mg), which proves an activation effect on titanaugite flotation. In alkaline solution, all these five kinds of ions can adsorb on titanaugite surface, and the floatability of titanaugite will be activation. Based on the above analysis, it can be deduced that in the flotation system using fatty acid as collector, the adsorption of metal ions on mineral surfaces and the stronger reaction ability with collector than active site on mineral surfaces, are the two prerequisites for metal ions show activation effect on mineral flotation.INTRODUCTIONIn flotation pulp, the existence of metal ions is often inevitable. There are two sources for these metal ions: the first part is generated in grinding and flotation process due to the oxidation, reduction, corrosion or dissolution of minerals or grinding medium; the second part is from the flotation water or the addition because of the technology need. The metal ions in the pulp have a considerable influence on mineral flotation. Earlier researches are focus on the activation effect of mineral floatation by metal ions to obtain a higher flotation efficiency, many effective activators were found, such as Cu2+ activated sphalerite, Pb2+ activation wolframite, and Ca2+ activation quartz flotation, these metal ions have become the commonly used activators in industrial production. And many studies attempted to explain the mechanism of how metal ions affect the floatability of minerals. James (James et al, 1972) suggests that metal hydroxide precipitation is the main component leads to activation effect, while the study of Fuerstenau (Fuerstenau, 1976) showed that the metal ion hydroxyl complexes played significant role. In recent years, the reuse of mineral processing wastewater has attracted more attention (Rao et al, 1989; Liu et al, 2013; Wang et al, 2014), as a main component in flotation wastewater, the influence of “unavoidable ions” on flotation process still need in-depth study."

Jan 1, 2018

By J. Jirestig

Poor grade iron ore, suffering from interlocked particles, is challenging for any process technology. Extensive grinding is required to attain liberation and to yield concentrates of desired grade. Fine particles are commonly very difficult to retrieve, resulting in value losses to tailings. In this paper, results from HGMS tests on fine to ultra fine hematite are reported. Special emphasis is put on slurry flow velocity. If hydrodynamic drag force, i.e. flow velocity is not controlled and kept constant during the feed and/or rinse phase, fine particles will not be captured and retained. Flow velocity control and constant flow during separation are achieved by discharge valves/slots and parallel magnetic flux and pulp flow configuration. In tests, increased slurry velocity from 178 to 268mm/s caused Fe-recovery to drop from 78 to 48%. Proving that flow velocity control is essential to optimise grade and recovery. HGMS tests at the Metso mineral laboratory on natural (weathered) hematite fines clearly show a large potential to recover valuables, currently lost to tailings. Even at particle size distributions as low as D80=35µm concentrate grades and recovery are very satisfying. Two samples, in-plant desliming rejects (D80=35µm and 50µm) where significantly upgraded and recovered, from 45,3% to 63,6% and 53,0% to 63,4% Fe, at 73,8% and 81,1% Fe-recovery respectively. Other types of in plant rejects, such as gravity separation or WHIMS tailings, also benefits from HGMS separation. Gravity separation reject, 55,8% Fe, at D80=500µm was tested, yielding a magnetic concentrate of 60,8% Fe at 50,7% Fe-recovery. The results indicated that the hematite was poorly liberated. HGMS separation was repeated after a regrind to D80 150µm, resulting in a magnetic concentrate of 62,8% Fe at 75,9% Fe-recovery. The tests prove that hematite, presently lost to tailings streams, can be recovered by HGMS and thereby significantly contribute to improved overall economy. Keywords: HGMS, magnetic separation, recovery of ultra-fine hematite, Indian hematite ores, hematite recovery from tailings

Sep 1, 2012

By Chen Dong, Yang Wenwang, Liu Zhineng, Tan Ming

"To meet the requirement of production expanding of a certain potash ore dressing plant in Xinjiang province of China, industrial test of XCF/KYF-50 flotation machine was performed to process potash ore. The tank of XCF/KYF-50 flotation cell is in U shape, 50m3 of volume. This flotation cell is able to suck slurry by itself, and can be arranged on the same base level without high difference. In this paper, two sets of XCF/KYF-50 flotation cells were adopted to replace 8 sets of 8m3 flotation cell in original flow sheet of flotation. Aeration rate, slurry suction capacity, power consumption and slurry suspension are investigated. The measuring results show the slurry suction capacity of the flotation cell is larger than 12.80m3/min and solid particles disperse evenly in the tank without deposition. Industrial test result indicates that the final grade of concentrate is 26.69% at the recovery of 90.95%, which is up to expected performance. XCF/KYF-50 flotation cell has advantages of high flotation efficiency, significant energy saving and reasonable configuration of automatic control system, this kind of flotation cell can meet the requirement of production expanding of this potash ore dressing plant well."

Jan 1, 2014

The major components of sylvinite ores, sylvite (KCl) and halite (NaCl), are separated by flotation. Since both these minerals are water-soluble, the process is carried out in a saturated brine, 6~7 mol/L aqueous solution of NaCl and KCl. C16~C22 primary amines, utilized as a collector, are practically insoluble in water. In commercial potash ore flotation operations these amines are melted by heating up to 70~90°C. They are then neutralized with hydrochloric or acetic acids, and such a hot emulsion/dispersion is introduced to the flotation pulp (which is at room temperature). This is immediately accompanied by the appearance of a white precipitate in the system. As our measurements indicate, the Krafft point of dodecylammonium chloride in concentrated electrolyte solutions is much higher than 80°C, and the Krafft point of C16~C22 amines is substantially higher than that. Introduction of a hot amine emulsion into a pulp, at temperature much lower than the Krafft point for the utilized amines, must cause precipitation of the amines. Some of these species are obviously flotation-active. It is interesting to observe that in summertime, when temperatures are high-er, longer chain amines perform better. It demonstrates that the colloidal amine species that precipitate serve as active species in the potash flotation. Therefore, at higher pulp temperatures, when the temperature difference between the pulp temperature and the Krafft temperature of the utilized amine is not sufficiently large, a longer chain amine, the amine with a higher Krafft point, is more efficient. The results reveal that premixing of an alcohol such as MIBC (common frother) with the amine significantly improves flotation performance of the amine. In the presence of such an alcohol the amine disperse system becomes less turbid, and the rheology of the system less non-Newtonian. All this indicates that MIBC, which does not operate as a frother in a potash flotation system, when used as a co-surfactant, enhances the dispersion of the amine colloidal system. The appearing colloidal species perform as an active form of the collector.

Jan 1, 2014

By Atsushi Shibayama, Toyohisa Fujita, Wan-Tai Yen, Ke-jun Liu

"In this investigation, a sponge gold sample (99.92% pure) has been leached with ammonium thiosulfate solution. The effects of CuSO4, (NH4)2S2O3, (NH4)2SO4, NH4OH and retention time on the gold leaching % (extraction %) and thiosulfate oxidation % (consumption %) have been studied. The copper ion acts as a catalyst in gold dissolution. On the other hand, it also accelerates oxidation of thiosulfate (consumption). It was found in this study that the best gold extraction condition was obtained at 43.2 ks with 0.8 - 1.0x103 mol/m3 (NH4)2S2O3, 30 mol/m3 CuSO4, 2.0 - 3.0x103 mol/m3 NH4OH, 0.4 - 0.5x103 mol/m3 (NH4)2SO4, pH 10±0.2 and 150 rpm. The thiosulfate oxidation was about 15% of the initial concentration.For gold recovery from the pregnant solution, the trioctylmethyl ammonium chloride (TOMAC) was used in this investigation as an extractant to extract gold from thiosulfate solution without pH and other adjustments. The effects of gold concentration, pH, ammonia, thiosulfate and cupric ionic concentrations, extractant and diluent concentrations and retention time on the gold recovery were investigated. It was found that 180 mol/m3 extractant diluted with n-octant at O/A ratio of 1:1 could extracted the 100% of gold in 0.6 ks from the thiosulfate solution at the optimal leaching conditions. The 100% gold stripping could be achieved with 10% thiourea solution."

Jan 1, 2003

By Z. S. Abisheva

Results of the study targeted to development of universal acidic-extraction-precipitation technology for gallium recovery from the sublimates are presented in the paper. This will let to utilize a new non-traditional source for gallium production. Phase composition of gallium containing dust was studied. Forms of gallium in the sublimates were determined. The main form is Ga2O3, however, GaP form is also present in the cottrel dust and Na5Ga3F14 form is present in the dust of aluminum electrolysis. The possibility of gallium concentration was established via secondary pyro-selection of the dust. Kinetics of interaction of dust components with sulfuric acid was studied. The products of the interaction subsequently were leached with water. Optimum conditions for direct leaching with HCl and H2SO4 were determined providing gallium recovery from the cottrel dust and the ash carry outs up to 95 %. Gallium recovery from the primary dust and the secondary dust of aluminum electrolysis was at 52; 64 % and 63; 83 % respectively. Effect of Fe, P, K, Na and Al admixtures for gallium extraction from hydrochloric acid solutions was studied. It was shown that gallium chloride complex (GaCl4-) is extracted into the organic phase from the following acid mixtures: HCl + H2SO4, HCl + H3PO4, HCl + H2SO4 + H3PO4, HCl + HF. Kinetic regularities of gallium extraction in the system (tri butyl phosphate) TBP ? HCl - Ga were studied using diffusion cell method with agitation. Optimum conditions for gallium extraction from complex hydrochloric acid solutions with TBP were found providing 99.9 % recovery and separation coefficient for gallium and iron (III) of more than 25 in one stage. Sodium hydroxide and water were selected as reagents for re-extraction of gallium from the organic phase. Different options for disposal of by-products that are formed in the processing of cottrel dust, ash sublimates and dust of aluminum electrolysis were proposed and tested. Keywords: gallium, kinetic, sulfatization, leaching, extraction, technology

Sep 1, 2012

By J. A. Sweet

The issues facing graduate training in the mineral processing industry are not too different today from those that prompted the initiation of the Anglo American Platinum Graduate Development Programme (AGDP) in 2002. Graduate metallurgists in South Africa enter the industry from different undergraduate programmes at various tertiary institutions, and so the knowledge and skills of the young graduates varies. Further, the geographical expansion of the industry combined with the downsizing of business units means that there are fewer opportunities for young graduates to be mentored through their first few years on site. Anglo American Platinum chose to address these issues by implementing an intensive, structured graduate training programme for all their new metallurgical graduates, known as the AGDP. The first two years of experience of the AGDP, from the viewpoints of both graduates and lecturers, were presented to the mineral processing community at the IMPC in Turkey in 2006 (Sweet et al, 2006). From the beginning, the programme was structured in a modular fashion to include a basic technical ?toolbox? including statistics, the scientific method and sampling protocols, while the mineral processing content comprised advanced learning in comminution, classification and flotation (later extended to include hydrometallurgy). Technical communication ? both written and verbal ? was included from the start. The programme was focussed very strongly on site work (?learning by doing?), with a major integrated site campaign conducted and analysed by each cohort. In 2012 the AGDP will accept its ninth cohort into the programme. This paper describes how Anglo American Platinum and the University of Cape Town have developed and adapted the programme over the last few years, in response to the challenges of the global recession, skills retention, and the changing operational needs of the company. The programme, which was drawn up to accommodate around 15 concentrator-only graduates, now accommodates 35-40 concentrator, smelter and refinery graduates annually. The programme has also been modified to facilitate new graduates spending most of their first year on the operations. The benefits of the programme for Anglo American Platinum have been tangible, and will be discussed in the paper. Keywords: graduate training, technology transfer

Sep 1, 2012

By Liu Chun-Bao Sun, Hong-Jun, Wei Zhang, Tao Xu

SABC circuits have gained widespread attention within China, and are being gradually applied to many mines. However, the domestic knowledge of comminution process is still relatively basic, and the design and production management of the application of SABC technology lack guidance of scientific theories. This research project focuses on the Phase I SABC milling circuits of Wu Shan Porphyry copper mine. Targeting the design and operation problems of existing process and circuit, and without increased investment and alterations in equipment, the new technologies will combine ordinary crushing and grinding theories as theoretical guidance, and borrow JK Simulation Software (JKSimMet) for analysis in order to optimize the comminution process, efficiently allocate production output and energy consumption, eventually resulting in increased production and energy efficiency. Using JKSimMet Simulation Software, and combining theoretical optimizing and practical production techniques, as well as the on-site situation, the eventual SABC comminution process and circuit optimization plan is: increasing the grinding Ball charge from 8% to 10% v/v in the SAG mill; Setting the Ball charge in the Ball mill to 27% v/v and the maximum operating power draw to 5 800kW; replacing the HP Series crusher with a TRIO TC84 crusher, which is without a power controller, and adding a pebble bin. The final optimization result is: Maximum system processing capacity increased between 20%-26.7%, specific energy consumption reduced by more 2.0 kWh/t, creating an economic benefit of over 300 million RMB, thus achieving the goal of increased production, reduced energy consumption, and improved profitability.

Jan 1, 2014

By Mohammad Noaparast, Hamed Haghi

"In this research work, it was attempted to reduce the iron contents (Fe2O3) in relatively low grade silica sample which was obtained from Shenin silica mine, using magnetic separation. The prepared sample contained 93.75%SiO2, 0.44%Fe2O3, 2.78%Al2O3, and 0.08%TiO2 and the Fe2O3 had to be reduced to less than 0.08%. Mineralogical studies and XRD analysis indicated the presence of Hematite, Pyrite, and Goethite as the major iron impurity phases. Mineralogical studies of polished and thin sections demonstrated that the degree of freedom of silica is more than 80% in -300+212 ?m size fraction. After primary stages including crushing, milling, scrubbing and de-sliming, various methods such as low intensity magnetic separation (LIMS), high gradient magnetic separation (WHGMS) and dry high intensity magnetic separation (DHIMS) were applied to find out that which process would be appropriate for the elimination of iron impurities from this sample. Different experiments were carried out on the product of wet rod mill and scrubber. However the magnetic field intensity of WHGMS was increased down to 2Tesla, and there was not any acceptable result in reduction of Fe2O3 content lower than 0.08%. Thereafter the product of wet rod mill and scrubber were dried and reported to DHIMS. In these experiments, maximum magnetic field intensity was 1.4Tesla. In this case very significant results were achieved, and Fe2O3 content of final product were reduced to less than 0.05% which meets glass manufacturing standards."

Jan 1, 2014

By Yuexin Han, Jie Liu, Shuai Yuan, Yanjun Li

"In order to improve recovery efficiency of iron minerals from iron ore tailings and to reduce its connected environmental pollution, this article investigated the reducing roasting of iron ore tailing in a laboratory fluidized magnetization roasting reactor to optimize the roasting method and conditions. The examined parameters included roasting temperature, roasting time and reducing atmosphere. The parameters evaluating magnetizing roast efficiency and theoretical value were determined. X-ray diffraction (XRD) analysis was used to investigate the conversion of iron phase after roasting. The results show that the best magnetizing roast conditions are roasting temperature of 540?, holding time of 15min, and CO concentration of 20%. The magnetization conversion ratio of roasting products is over 80%, under the best magnetic separation condition, the concentrate grade of iron is 65.61 % and the recovery of iron is 83.77 %. The XRD analysis shows that Fe exists in hematite and siderite before roasting and exists in magnetite after roasting. The technique not only recovers the iron minerals from tailings with good economic benefit, but also reduces the environmental pollution of tailings accumulation.INTRODUCTION Iron ore tailings are the solid wastes generated during the beneficiation process of iron ore concentration and are one of the main pollution concerns in the mining industry (Das et al., 1996). Continuous development of the iron and steel industry has led to the increasing amount of iron ore tailings; there are over 300 million tons of iron ore tailings discharged per year (Rao et al., 2016). The huge amount of stockpiled iron ore tailings brings a series of environmental and social problems. Comprehensive utilization of iron ore tailings can not only reduce environmental load but also conserve resources, promoting sustainable development of the society. In recent years, iron ore tailings as secondary resources have received considerable attention in many countries in the word and numbers of studies on utilization of iron ore tailings were carried out, such as recycling the valuable minerals (Datta et al., 1996; Jia et al., 2013; Panda et al., 2018), used in construction material compositions as alternative source of raw materials (Das et al., 2012; Zhou et al., 2012; Luo et al., 2016) and other utilization. The iron minerals were recovery by magnetization roasting (Rao et al., 2016; Yang et al., 2013; Yang et al., 2011) and flotation (Kumar and Mandre, 2016). By comparison the reduction roasting has more advantages, but it was found that the conventional roasting equipment was inefficient, high energy consumption and un-economically applied on an industrial-scale."

Jan 1, 2018