Search Documents

By Steven D. Dapp

The use of base grouting (tip grouting) to enhance the axial capacity of drilled shaft foundations can achieve improvements in economy and reliability for many types of projects and soil profiles. Recent experiences on a range of different construction projects in the Southeastern U.S. illustrate the most attractive opportunities for utilizing this technique and some limitations of the method. The quality assurance provided by measurements obtained during post grouting the pile toe is another important aspect favoring its use; the base grouting is shown to identify weaker piles and provide a means of remediating some deficiencies so that increased foundation reliability is achieved. This paper provides an overview of the methods used to evaluate and design for base grouted shafts along with lessons learned from several case histories.

Jan 1, 2006

By Jom Gentry

Acrylamide chemical grout (C3H2NO) has been successfully used for over 50 years to control groundwater and stop infiltration. This paper will address three unique projects involving the control of groundwater with each study providing special circumstances and geological conditions: encapsulation of radioactive hazardous waste in the United States, a tailings dam for a large copper/gold mine in Argentina and 27 miles of leaking subway in Canada. The primary reasons for selecting acrylamide grout were based on the following characteristics: thinnest chemical grout on the market, a true solution grout which contains no suspended solids in the blended product, flexible gel set times, and a 362 year half-life in soil as determined by the U.S. Department of Energy.

By F. Castelli

A simplified non-linear method to predict the behaviour of a single pile and/or pile group under horizontal loads is presented in the paper. The evaluation of the non-linear lateral deflection is based on a procedure taking into account the decrease of the model stiffness with the increasing of the applied load. The solution derived firstly for the single pile, was extended to the case of a pile group introducing the p-multiplier (fm) concept proposed by Brown et al. (1988).

Jan 1, 2006

By Daniel J. Rider

In 1980 the Niagara Frontier Transportation Authority contracted for three miles of cut and cover box structure and station construction in Main Street, Buffalo, New York. Project depths ranged from 30 feet to 60 feet below street grade. Soils, Figure No. 1, consisted of loose to very compact sands and gravels. Ground water level was generally 20 feet below grade. Specifications required a soldier pile and timber lagging support system with external dewatering. Soldier piles were to be installed in prebored holes with bentonite slurry and lean concrete backfill. Conventional pile driving was not allowed due to concerns over excessive noise and vibrations and its effect on nearby historic structures and the surrounding population

Jan 1, 1987

By D. V. Karandikar

Contiguous bored piles have been used in the past for retaining the sides of deep excavation. An innovative version of this method was adopted successfully in two prestigeous projects in Bombay in which in a very constricted and congested locality, adjoining seashore at Walkeshwar, 14 m deep excavations with vertical sides were required. 600 mm dia bored cast-in-situ piles were first installed at 1.2 m c/c and subsequently as the excavation proceeded, they were tied to cast-in-situ RCC waling beams. The shear connectors to the beams were pre-fixed to the pile reinforcing cage at specified depths. The pile / waling beam system was anchored into the ground by installing inclined prestressed cable anchors at the designed depths. The waling beams were also used to support the brickwalls, which formed the required backup wall for fixing the tiled water proofing system. Catch-drains were installed behind the brickwalls for relieving the ground water pressure and thus ensuring a very economic design. The adequacy of the system was proven in that where the system was not installed in time, failure of the sides occurred during monsoon. Whereas in the areas where the above retaining system was installed, there were no problems inspite of heavy monsoon and surcharge of construction materials and equipment. The system became a very effective and economic alternative to an anchored diaphragm wall. The paper presents the case studies of these two projects.

Jan 1, 1996

By Cassandra A. Wetzel

Rock socketed mini-piles are a desirable foundation alternative when design capacity is more than 40 tons and there is limited access. In this case history mini-piles were designed to support between 75 and 200 kips at 12 locations adjacent to a perimeter wall, a party wall and at cast iron column piers. Limited geotechnical information, low overhead clearance, and active building population tested the creativity of the team to get the piles installed. The key geotechnical concern during installation of the mini-piles was the presence of a glacial till layer above the bedrock surface that restricted the seating of the casing into bedrock with a track mounted drill rig. Soil loss during the advancement of the rock socket using an air hammer was excessive and increased the risk of subsidence. Over a three week period the engineer worked with the contractor to modify the design, means, methods, and materials to install piles with adequate load capacity. This paper will present the changes in design and construction methods that were required.

By Koichi Kobayashi

Performance-based approach to design of structures including foundations was adopted after enforcement of the revised Building Standard Law in Japan in 2000. The use of piled-raft foundation is favorable for medium-rise buildings in soft ground because of its good performance. In the design of the piled-raft foundation (Architectural Institute of JAPAN2002), vertical load is usually carried by the raft foundation, while the pile is primarily meant to control settlement of the structure. Shaft friction is expected to be larger in a nodular pile(Karkee, et.al., 1998) since it has larger surface area than a straight pile, and such piles are frequently used in piled-raft foundations. Since few structures with piled-raft foundation exist currently, the settlement characteristics of piled-raft foundation have not been fully clarified. To design piled-raft foundations with better confidence, the mechanism of vertical bearing capacity and the spatial distribution of settlement should be clarified, for which the actual behavior of the building-foundation system needs to be evaluated. This paper presents observations of settlement of a building with a piled-raft foundation at a soft ground site. The building is a steel structure covering an area an 766 m2, and consists of two-storey office block and one-storey warehouse block. The filled ground of about 5-m thickness at the ground surface is underlain by approximately 4-m thick alluvial sand layer below which lies about a 17-m thick alluvial clay layer with SPT N-value less than 2. The piles used in the piled-raft foundation are 12-m long nodular piles with nodal diameter of 500 mm (pile shaft diameter is 400 mm). The bored pre-cast piling method (Karkee, et.al., 1998) was used to install the piles. To evaluate the foundation settlement, the method of analysis of three-dimensional frame system, utilized widely in Japan, was adopted in combination with the foundation system. Basic assumptions were: (i) total ground settlement is evaluated as the sum of immediate settlement and consolidation settlement, (ii) immediate settlement is evaluated from the Mindlin?s solution in which strain dependency of shear modulus of soil is considered, (iii) settlement in clayey layers is evaluated by the one-dimensional consolidation theory, and (iv) shear spring between soil and pile shaft is represented by a hyperbolic function. The applicability of the method of analysis was verified by comparison with results of field monitoring of building settlement.

Jan 1, 2006

By Vahid Tajdar

The behavior similarity between pile and cone penetration test, has guided the researchers to use the CPT results in prediction of piles bearing capacity. In this article, artificial neural networks have been used to study about relation between cone tip and sleeve friction strength obtained from cone penetration test and ultimate pile bearing capacity, obtained from static pile load test. Artificial neural networks "ANNS" is a form of artificial intelligence. ANN tries to dramatize the human nerves & brain system biology structure in self-structure. In this article, the results of relevant studies about the prediction of ultimate pile bearing capacity in especial area of soils are presented by use of back - propagation neural networks. The results of static pile load test up to failure on 63 piles with closed end and CPT test results in the place of construction these piles use in order to confirm and creation ANN model. Comparing predicted ultimate pile bearing capacity by utilizing ANN with the numbers which are predicted by 5 common traditional methods shows that using of artificial neural networks is a suitable method for predicted ultimate pile bearing capacity in identified area of texture of soil moreover it has a better operation in comparison with common traditional methods.

Jan 1, 2006

By Zhu Tonghao

A method of calculating anti-slide pile, sheet pile, underground diaphragm and structure with anchors etc. is proposeed in the paper. The effect of the various layers of soil, anchors and bracings etc. on laterally loaded structures may be considered in the model. In the analysis the structure is divided into a series of elements. The transfer matrices of both deformation and internal force are established for each element. According to continuous condition neighbouring element should be connected. Thus the deformation and internal force of each element can be found out in conbination with boundary conditions. The method has a wider adaptability and it can be applicable to a great variety of the analysis of interaction between various structure and soil. If parameters in model are selected properly, the computed results would be in good agreement with the measured data.

Jan 1, 1991

By Dimitrios Polantzas P. E., Collin E. Sweeney E. I. T., Franklin M. Grynkiewicz P. E., Leili Javidanian P. E.

In the latest AASHTO design specifications, the Load and Resistance Factor Design (LRFD) method is prescribed for the design of retaining walls. However, inconsistencies arise when LRFD is used for retaining wall design versus the traditional Allowable Stress Design (ASD). Required toe embedment and wall loading demand vary greatly when the two design approaches are compared, all else being equal. This is due to application of linear load factors to properties that vary non-linearly in the design. These inherent inconsistencies are further intensified when introducing factors such as layered soil profiles, different wall types, groundwater elevation, and surcharge requirements. When applied correctly, these two design approaches, in theory, should lead the designer to the same result with little discrepancy, as they do with steel structure design. However, the use of the current AASHTO LRFD method for various geostructural retaining wall designs yields contradictory results that suggest existing retaining walls that have been successfully designed and constructed are unstable. Fundamentally, LRFD should be built on reliability-based calibrations; the successful past performance of existing retaining structures designed using ASD suggests that the LRFD approach requires considerable modification. The authors of this paper recommend that the current LRFD load factors be reviewed and revised based on more comprehensive wall performance data and wall type such that the difference between retaining structures designed using LRFD and those designed using ASD is eliminated.

Oct 1, 2022

By Wu Jian-tao, LI Guo-wei

"The Cement Mixing Pile (CMP) quality assurance assessment is an important programme in evaluating the efficiency of foundation improvement. Coring is the current specified method of quality assessment in China which has the shortcomings of long cycle, high cost and low efficiency. The field and laboratory test show that the regular cone penetration test can only detect maximum of 4m of effective detection depth in CMP. In contrast, the method of cone penetration test in the reserved hole can detect the quality continuously along the pile at any depth. The tip resistance of reserved hole penetration in the 7th day has good linear relationship with unconfined compressive strength in the 28th day. The slope of linear relationship decreases with the increasing of clay particles content.INTRODUCTIONThe method of Cement Mixing Pile (CMP) is often used to improve soft soil foundation in highway construction, with the major purpose of reducing settlements under embankments (Bruce et al., 2000),which is a form of what is known as the Deep Mixing Method (Bruce et al., 2013). The CMP technology spread quickly in China in the 1980s. CMP quality assurance assessment is an important programme in evaluating the efficiency of foundation improvement. Coring is the current specified method of quality assessment in China (China Academy Of Building Research, 2002). The method of Coring is perceived in some quarters that samples will provide lower strengths given the distress caused to the core during drilling and extraction (Bruce et al., 2002).The cone penetration test CPT can provide continuous measurements of the penetration resistance, sleeve friction at the tip of the probe, which has advantages of simple operation, low cost and high efficiency compared with coring. However, CPT tests have not been established to assess CMP in Sweden because of difficulties in maintaining verticality (Larsson, 2005). In Finland and Norway, however, CPT tests are commonly used (Halkola, 1999). One of the disadvantages of CPT is the tendency of the cone to steer out of the column (Porbaha et al., 2003). Darya Mokrousova (2010) states this tendency to deviate can be overcome by pre-boring and starting the penetration test from the base of the pre-bored hole. Sheng Haiyang (1999) found that probes may be deflected out, sometimes even at small penetration depths, and may not give a complete inspection of the pile. Liu Songyu et al. (2003) suggested that the Standard Penetration Test (SPT) is an effective way to evaluate the strength and quality of stabilized soil-cement columns. In general, Regular CPT can’t test the full length of CMP, and SPT still needed drilling which causes discontinuous detection. From the existing standard of China, core sampling compressive strength test is the main method, evidently, coring displays a longer test cycle, high cost and low efficiency. Therefore, an improvement of CMP quality assessment, by conjuring a fast and reliable detection and evaluation method, is necessary. The aim of this paper is to research the feasibility of using CPT in assessing the quality of CMP and presents an improved CPT method."

Jan 1, 2015

By Ke Yang

Drilled shafts are widely used as foundation system for sound walls to resist lateral loads. The design method based on the ultimate lateral capacity, such as Broms method, is often used for sound wall foundation design. Allowable Stress Design (ASD) is currently used for deep foundation design. However, by October 2007, all states Department of Transportations are required to use the Load Resistance Factor Design (LRFD) approach for the design of foundation in highway projects. There is a need to develop a calibrated resistance factor in LRFD lateral design of drilled shafts supporting sound barrier walls. This paper provides resistance factors for design of laterally loaded drilled shafts supporting sound walls using Broms method based on the study using reliability based method and fitting to ASD method. Additionally, the resistance factors for static lateral load tests are recommended. Furthermore, a methodology to update the resistance factors using Bayesian approach by incorporating the on-site full-scale lateral load test results is presented. To illustrate the Bayesian update methodology, two lateral load tests in Colorado were employed to develop the updated resistance factors.

Jan 1, 2007

By Marie-Pierre Bourdouxhe-Barnich

Since 1997, in partnership with the Laboratoire Central des Ponts et Chaussées in Strasbourg, ProfilARBED has been carrying out a vast study to qualify the improvements jetting can make to vibratory driving of steel sheet piles, and to understand its effect on the surrounding ground and on the sheet piles themselves. The process basically involves discharging a fluid (mostly water, sometimes in association with air) at controlled pressure and/or flow rate near the toe of the sheet pile being driven. The steel jetting pipes are attached to the sheet pile and are connected to the pumps by hoses. The jet of fluid loosens the soil, thus reducing the resistance at the toe of the sheet pile. Depending on ground conditions, the fluid that flows along the pile can reduce skin friction. Four soil types were involved in our experiments. Each site was instrumented: the driving parameters and the geotechnical characteristics of the soil before and after vibratory driving and jetting-assisted driving were recorded. Each test provided its own particular information which contributes to overall thinking on the matter and is of help to project managers who are often confronted with rapid driving to the final depth.

Jan 1, 2002

By Harry K. Weatherbee

The paper presents a design case study for a four-story correction facility addition in south Boston, Massachusetts, supported on friction piles driven into the Boston Blue Clay. 356 mm (14-in.) square prestressed-precast (PSPC) concrete piles were selected as they were found more effective and economical. A static load test was performed where the pile was brought to "failure". The load test data were evaluated to estimate the Ultimate Pile Capacity as well as the Ultimate Unit Skin Friction (Adhesion) to serve as a design tool for friction pile projects in the south Boston Area.

Jan 1, 2003

By Patrick P. A. Wolfs

In the summer of 2000, the ECR®/EFT® was first introduced in the Netherlands. After the first project a field test was performed together with other geophysical methods to prove the liability of these systems and their application in areas with soft soil and high groundwater levels. The objective of this test, which was carried out with three leakage detection systems, was to locate the holes. After this test several projects have been carried out. In this article the Dutch projects "Ringvaart Aqueduct" and "Bottleneck Limburg N296/N297" are mentioned.

Jan 1, 2006

By J. Matos e Silva

"Abstract The paper refers five examples of executed diaphragm walls with one to five levels of anchorages. For each example a comparison is made between the results of the design using the traditional criteria and the ones obtained by using the Eurocode 7 and the Portuguese Norm related to the EC7 (NP EN 1997-1 2010), as the Eurocodes consider the possibility of each European country to adopt their own geotechnical parameters as these may vary from one country to another. A comparison is also made with the behaviour of these diaphragm walls during its construction phase; so the values from the design that were adopted in the construction are listed in tables 2 to 6 in the “Construction Options” columns. From the referred examples the author presents his conclusions.1 - INTRODUCTIONIn the so-called “traditional criteria” the soil parameters (dry unit weight, angle of internal friction and cohesion) have values obtained through tests or empirically. It is assumed that the characteristic values of the soil parameters adopted in Eurocode 7 are equal to the soil parameters adopted in the calculations by the “traditional criteria”. In the present paper the design according to the EC7 was made considering only the ultimate limit states and the respective Cases A1 and A2.The partial coefficients used for the actions in the present paper were those on Table 1:2 - CONSIDERED EXAMPLESThe five examples correspond to the situations of figures 1 to 5, and the respective results are summarized in tables 2 to 6.For all the considered examples, that are case histories, a simplified method published by Matos e Silva (March 2000) was adopted. This method attains good performances when compared with other more sophisticated ones as the finite elements and the elasto-plastic methods as described in a paper published by Matos e Silva (2000). All the obtained values were compared between them and with the so-called “Construction Options” that were the values adopted by the designers of the considered examples. For the wall bottom length calculation two possible situations were envisaged:"

Jan 1, 2014

By A. J. Partos

The figures and tables referred to herein are presented in the Proceedings; Volume I, Pages 309 through 316. The 61-story One Liberty Place, at 315 m., is the tallest building 1n Philadelphia and was in 1987 the ninth tallest building in the world. One Liberty Place is supported on drilled piers socketed in heterogeneous metamorphic rock. Design load distribution was 40% on the base and 60% by shaft resistance. Drilled Pier G-10 supporting a T13-A type outrigger column was instrumented. There 1s no uplift load on the exterior outrigger columns. This column supports a 53,850 kN compressive load which includes a 13,440 kN windload. Table 4 presents experimental parameters from straight line interpolation of Mohr failure envelopes for the Wissahickon schist. Lowest values of cohesion (12,200 kN/m2) and angle of internal friction (19°) are at a 50° - 59° angle of foliation. Figure 3 presents a typical pier supported by shaft resistance 1n decomposed (D) and coreable (C) rock and by end bearing (B).

Jan 1, 1991

By Abhijit Saha

"Two analytical closed-form elastic-rigid-plastic solution methods to predict the rigid foundation behaviour on stone-column reinforced soil are compared, both of which takes into account the stone material yield within the host soil according to stress-dilatancy theory. These are the mechanistic methods developed by the author (2004, 2005) [that presently incorporates the dilatancy angle as per Schanz and Vermeer (1996)] and that developed by Pulko and Majes (2006), that takes into account the column yield as per Rowe dilatancy theory. Since optimal design of stone column necessitates optimum stress concentration on column, which is generally composed of dense gravel with/or without sand, the vertical stress on granular column is often close to its peak strength and the material dilates. To arrive at closed-form analytic solution to this complex soil-stone column interaction problem, some common assumptions like axi-symmetric soilstone column ‘unit-cell’, elastic host soil and rigid-plastic Mohr-Coulomb stone column material are combined with equilibrium and kinematic conditions. The results reflect the beneficial effect of dilatancy within the optimal range or techno-economic domain of area-ratio. The settlement predictions are compared with other analytical methods available in literature as well as with measured settlement reduction of stonecolumn reinforced ground at different subsoil conditions around the globe reported in literature.INTRODUCTIONStone columns or granular piles are frequently used in stabilization of soft clays, silts and loose silty-sands with large amount of fines. The majority of analytical methods assume infinitely wide loaded area with end-bearing columns having constant diameter and spacing that approximate to axi-symmetric conditions, and the approach is known as ‘unit-cell concept’. Several analytical solutions are available, and many of them (Aboshi et al; 1979, Balaam & Booker; 1981) are based on elastic approach considering the stonecolumn and surrounding soil as elastic materials. However, elastic methods give the ratio between the vertical stress in the column to soil (stress concentration factor) approximately equal to the ratio of constrained modulus of both materials. This ratio was found to be considerably higher than measured in the field and it is believed that elastic methods may overestimate the effects of stone columns on settlement reduction (Barksdale & Bachus, 1983). The elastic and elasto-plastic solutions presented by Balaam and Booker (1981, 1985) indicate that the problem can be idealized by assuming that the stone column is in a triaxial state and possibly yielding, such that there is no shear stress at the stone-soil interface and no yielding in the soil. Similar assumptions of stone column to be in a state of limiting equilibrium and under a triaxial stress state are considered in other methods also (Priebe; 1976, Van Impe & De Beer; 1983, Van Impe & Madhav; 1992, Saha & De; 1994, Saha; 2004, 2005, Pulko & Majes; 2006). In majority of the methods it is assumed that under load the stone-column yields at constant volume. However, the last three cases cited consider another parameter; the dilation of stone column. In Van Impe and Madhav’s (1992) and author’s (2004, 2005) method, the dilation is taken into account through the final value of the volumetric strain of column, whereas Pulko & Majes (2006) considered the stone column as Mohr-Coulomb rigid-plastic; dilating at yield in line with Rowe (1962) dilatancy theory."

Jan 1, 2015

By Peng Jiahong

With ultrasonics application during checking the large diameter cast-in-situ pile body, it is usualy applied the statistical method of probability and PSD. This paper presents a converse probabilistic-analytical method which can identify important anomalies, both strong and weak, during interfered situation. So the inhomogeneity in concrete pile may be ellectively distinguished. In order to ensure the capacity of bed rock support layer under large diameter pile, a test-in-situ is conducted to determine the compresive strength and shear force inserting rock of the support layer, so the compresive strength and modulus value of elasticity of bed rock tested will closely tally with the actual situation.

Jan 1, 1991

By Thomas J. Weaver

Piles extending through soft soil near the ground surface will have a relatively low lateral stiffness. As a result, lateral serviceability limits may control the number of piles required for foundation support. Improving near surface soil properties may significantly increase lateral pile stiffness and thus reduce the number of piles required for the foundation. A series of analyses have been performed to assess the depth and lateral extent of soil improvement required to significantly increase lateral foundation stiffness. Analyses consisted of Winkler type beam on a spring foundation and three-dimensional, linear elastic finite element analyses. Results from the analyses show that lateral pile foundation stiffness can be doubled when soil properties are improved to a depth and lateral extent of 5 pile diameters. In order to achieve this increase in foundation stiffness, the modified/improved soil modulus of elasticity needed to be approximately 5 times greater than adjacent unimproved soil. This magnitude of soil improvement over such a limited lateral extent suggests that limited soil improvement can result in more economical foundation designs at soft soil sites.

Jan 1, 2006