Search Documents

By Frank J. Purcell

“Down The Hole” (DTH) hammer drilling is often necessary to advance the casing during pile construction where the test bores have determined difficult drilling conditions with obstructions such as boulders, cobble and glacial till. The use of compressed air to operate DTH hammers in foundation drilling has been a contentious point in many regions of the world due to its potential to disturb the ground around the pile being constructed. There are many examples of damage to adjacent building foundations where compressed air exiting the pile being drilled disturbed the subsurface around the building’s existing piles. This paper looks at the use of compressed air in DTH hammer foundation drilling and the move towards controlling the exhausted air to avoid over drilling the pile, causing potential damage to nearby piles. Simulated models of air flow penetration into the soil of different configurations of drill bits are discussed to highlight design changes employed to better control the air during the drilling process. A case study of the construction of a water-tight pipe pile wall for a building’s underground parking structure is studied to demonstrate the potential of DTH hammer foundation drilling where the air is fully controlled.

Nov 1, 2022

By Kishore Kumar B., Eswaran Prasad C R, Srini Naik B., Ramakrishna Raju N

The authors through this paper intend to introduce the non-vibro technique of ground improvement by stone column, being used for the first time in India under the Western Dedicated freight Corridor in Mumbai area. New 2x25 KV double line dedicated freight corridor tracks, capable of carrying 32.5-ton axle load are proposed to be built on this stretch. Non-Vibro Displacement Stone Columns of 900 mm diameter were installed to improve the safe bearing capacity of the soft ground to take the loading of Dedicated Freight Corridor Railway embankment. Vertical footing load tests on single and three column groups were conducted to assess the improvement in the sub-surface condition after installation of stone columns. This paper describes load tests conducted on stone columns and analysis of the obtained results. The observed load settlement behaviour of the improved ground has also been presented. Behaviour of single and group of stone columns have been compared and criteria adopted for arriving at desired factor of safety based on the settlement observed, has also been discussed.

Nov 1, 2022

By Satyajit Vaidya, Rudolph Frizzi, Quadri Owokoniran

"This paper presents a case history in the design and construction of high-capacity drilled shafts for the iconic New York Wheel presently being constructed along the St. George area waterfront in northern Staten Island, New York. Although the site is located in an area that offers views of the Statue of Liberty, the Manhattan skyline, and New York Harbor, the variable and challenging subsurface conditions at the site and the structural loading requirements for Wheel erection and service conditions presented geotechnical design and construction challenges. The paper focuses on site and subsurface conditions, drilled shaft design and construction details, results of Osterberg-cell and lateral load testing, and load test data analysis and evaluation.PROJECT DESCRIPTIONThe proposed 630-foot (190 m) -tall New York Wheel (the Wheel) is projected to be one of the tallest observation wheels in the world. Upon completion, the Wheel will be capable of carrying over 1,400 passengers in its 36 capsules. The Wheel site is located along New York Harbor offering views of the Statue of Liberty, the Manhattan skyline, and the New York Harbor; see Fig. 1. The Wheel structure is sited along the waterfront, and served by a 3-story terminal located south of the Wheel in the eastern portion of the site and having a footprint area of about 34,250 sq-ft (3,180 sq-m). A 4-story parking Garage, with a footprint of about 112,840 sq-ft (10,480 sqm), is to be constructed south of the Wheel in the central and western portions of the site.SITE AND SUBSURFACE CONDITIONSThe site’s close proximity to the New York Harbor presented geotechnical challenges because the site is located in an area that was once beyond the historic shoreline of Staten Island. The site is an about 350,000-sq-ft (32,500-sq-m) parcel generally bounded by the Richmond County Bank Ballpark to the southeast, the 9-11 Memorial to the east, Bank Street to the north and northeast, and Richmond Terrace and an associated retaining wall to the southwest and south. A 50-ft (15-m) -wide New York City Transit Easement, with an active on-grade service area and tracks, is located in the southern portion of the site. See Fig. 2 for site location and approximate location of the Wheel foundation footprint."

Jan 1, 2016

By James Coull, Brian Wilson, David Siddle

"In 2012, Golder Construction Inc. was awarded a Design-Build contract for the design and construction of an extensive, deep ground improvement scheme to support up to 20 metres (66 ft) high Mechanically Stabilized Earth walls and bulk earthworks required for the development of the proposed Kitimat Liquefied Natural Gas (LNG) facility at Bish Cove, British Columbia (BC). Utilizing Cutter Soil Mixing (CSM) to construct barrettes consisting of overlapping rectangular panels of in-situ cement-treated soils, a deep mixing scheme, covering an area of approximately 12,900 m2 (15,430 yd2) and comprising some 1645 CSM panels to depths of up to 30.7 m (101 ft), was developed to provide the required static and seismic stability for the LNG structures, and meet the project-specific performance criteria.CSM panels were constructed through varying thicknesses and discontinuous layers of fine-grained, very soft to soft marine deposits, and loose to compact sands, with occasional interbeds of dense sands and gravels. Panel completion criteria was based on soil response factors, as measured by the CSM equipment, with the design requiring a typical embedment of about 2 m (7 ft) into dense silty sand to sand and gravel to provide the required bearing. A total volume of approximately 73,900 m3 (96,660 yd3) of soil was treated with cement to consistently yield average unconfined compressive strengths exceeding 2.5 MPa (363 psi).This paper outlines the challenges associated with the construction and quality control of this large deep mixing scheme in highly variable geotechnical conditions at a remote location with barge-only access, and limited communication facilities. Specifically the paper will discuss the logistical challenges faced and solutions adopted for the project; equipment redundancy requirements for a 24/7 operation; the impacts of wear and tear, as well as variability in subsurface conditions on productivity; quality control processes adopted for the project, including the value of provision of an on-site laboratory; and materials handling issues, and their impacts on mix design and quality control."

Jan 1, 2017

By Lenin T., Madhav M. R., Padmavathi V.

Use of PVDs and preloading on the ground can significantly reduce the time taken for ground to consolidate. Many soils in situ are lightly overconsolidated, with overconsolidation ratios (OCR) ranging from 1.0 to 2.0 due to various reasons such as glaciation, ground water level fluctuation, aging, cyclic loading, creep, erosion, cementation, etc. The effects of overconsolidation ratio are analysed in this study. Compression index and consolidation coefficient are important parameters in determining time – settlement response of soft soils under preloading and with PVDs. These parameters are typically estimated using oedometer tests on samples, with the assumption that the results represent the entire deposit. The in-situ time-settlement plots at different depths are used in the back analysis for estimating compressibility and consolidation parameters of in situ ground, resulting in more representative values that reflect the deposit's overall behavior. From observed time versus settlements plots, variations of compression index and coefficient of consolidation with depth of a deposit are presented. Estimation of compression index with depth is possible based on different OCR values as shown in this study. Barron (1948), Asaoka methods are used to estimate the coefficient of consolidation with flow in the radial direction.

Sep 1, 2022

By Chandramohan P. V

A unique tension pile where the pull is at a point a certain distance below the top of the pile. The pull is transferred by a cable consisting of high tensile strands. The HDPE duct of the cable prevents bond between the strands and pile concrete in upper portion. While soil friction on the pile will act downwards on the whole length, there is tension in the bottom portion of pile, there will be compression at the top portion.

Nov 1, 2022

By Nagarajan. D, Raja Rajan. K, Vijayakumar. T

Major bridges crossing mighty rivers must be constructed in flowing water. Constructing the sub-structure in water has been a challenging job for contractor. Special construction techniques with marine fleets to be adopted for waterfront construction. Enabling works like temporary piling platform and cofferdam used for pile and pile cap construction. Apart from this, enabling works like load out jetty to transport the materials from land to water; temporary walkway for access of workman to work location; temporary access bridge for construction vehicles movement; temporary liners for tower crane foundation; Concrete block to act as dead man anchor for barge movements were all required by the contractor for smooth functioning of site as per construction schedule. Investment in enabling works by contractor plays a significant role on profit margin of the project and of course with utmost safety. Design of enabling works for waterfront structures involves hydrological data like afflux, bathymetry survey, current force, scour depth and wave force to be taken cautiously for safe and economic design. Type of foundation and pile/well cap top level corresponding to water levels shall influence the construction scheme. Usage of geotechnical software like Wallap and Plaxis required for enabling work design to enhance the safety of the structure. Bathymetry and soil condition play a critical role in design and construction of enabling works. Water Discharge quantity in river along with water levels like low water level, high flood level, seasonal fluctuation of water levels has a great impact on design of enabling works. Establishing enabling works for waterfront construction near to an existing bridge is an additional challenge for the contractor. Along with design, constructing the enabling works in water requires special construction methodology and sequence of work. This paper shall provide insights on overview of design and construction of enabling works for waterfront construction.

Nov 1, 2022

By Nasr Sheta

"After Hurricane Sandy, the stability of an earth slope in the Atlantic Highlands, New Jersey in the United States was deteriorating due to slumping soils and erosion from flooding. A slope stability evaluation indicated the slope did not satisfy the requirements of the local building code. A triple-tier, pile-supported and mechanically stabilized earth wall was designed and constructed to stabilize the slope. The construction was planned from a 3-m-wide roadway and, because of rough terrain and limited work space at the site, a cast-in-place drilled-pile construction was deemed impractical due to slow pile production. An alternative procedure was utilized by pre-drilling holes, and installing precast tip-and-shaft-grouted (PCTSG) piles, which extended to competent soils to improve slope stability. A grade beam, connecting the PCTSG piles along with soldier beams and concrete lagging were used to form the lowest tier of the slope stabilization, while the middle and higher tiers were built as mechanically stabilized earth. The stability of the proposed stabilization was analyzed using 2-D non-linear finite elements. After construction, monitoring of the wall continued for about 8 months to check its performance, and indicated lateral and vertical wall movements were less than 25 mm and 6 mm, respectively, indicating effective slope stabilization.INTRODUCTIONStabilizing earth slopes using piles to connect near-surface unstable soils to underlying stable ground masses has been investigated by many researchers, who presented various approaches to evaluate the contribution of the pile system towards improving the stability of the slope. Some of these approaches consider the piles as structural elements receiving forces from the upper sliding ground mass and transmitting these forces to the underlying stable one. The force from the top sliding mass is applied at between one third and one half of the pile embedment into the top sliding mass, Anagnostopoulos et al. (1990), Fukuoka (1977) and Matsui et al. (1988). The point of application of the sliding force was explored based on successful case histories while addressing the safety factors for both geotechnical and structural design, Vessely A. et al. (2007). The development of numerical analysis techniques utilizing the method of finite elements (FE) also enabled better analysis and design of slopes stabilized using piles. A FE-based approach was successfully utilized to design slope stabilization with target safety factor based on the shear and bending demands and the spacing of the piles, Pradel D. et al. (2010).After Hurricane Sandy in October 2012, the stability of many properties constructed atop earth slopes located along the coast of the Atlantic Ocean has become a concern due to storm-induced erosion. This paper presents the analysis, design and construction of a hybrid slope stabilization system utilized at one of these storm-impacted properties, which is located in the Atlantic Highlands, New Jersey in the United States. The subject property consisted of a two-story residential dwelling and a parking structure, and was built on top of an about 8-m-high earth slope having crest at about elevation 10 m (el 10) and toe at about el 2."

Jan 1, 1900

By Ali S. Fayad

"In June 2014, Orange County Flood Control District (OCFCD) completed construction improvements of the East Garden Grove-Wintersburg Channel for a price of $42 million. Instead of the pre-existing traditional trapezoidal levee, the channel was improved with a vertical compact levee. Dubbed Soil-Mix-Sandwich (SMS), this geo-structural and environmental solution for coastal channel improvements, underlain by liquefiable soil strata, was both a design and construction innovation. It employed Deep Soil Cement Mixing (DSCM) within the confines of a hydraulically-pressed (Giken Method) sheet pile duo. SMS was unique because it incorporated both subterranean and supra-dredge-line soil mixing within a very narrow workspace. Its DSCM pattern aimed at optimum densification of the workspace and was confirmed during the construction process. It availed the DSCM sub-contractor (Hayward Baker Inc.) the opportunity to demonstrate the fitness of their huge wet-mixing machinery within a very confined access-area and introduced approximately 70,000 cubic yards of DSCM within a limited 15 foot workspace width that stretched for a mile. The sheet pile duo created a construction-enclosure that became a stay-in-place load resisting system. PROJECT CHRONOLOGY AND LOCATIONAn Orange County Flood Control District (OCFCD) project-report was commissioned to study the East Garden Grove Wintersburg channel (OCFCD facility # C05). The report examined the hydraulic conveyance of the C05 channel and was concluded in 1994 by Williamson & Schmidt. The project-report did not encompass extensive geologic studies; but it provided several alternatives for channel improvement. It recommended a single row of sheet piles as the preferred alternative for the downstream reach.The most downstream reach of the C05 channel is located in an environmentally sensitive area, in City of Huntington Beach, California, USA. Its site includes seismic chasms that surface within the C05-footprint (the Newport- Inglewood tectonic fault). Extensive deposits of liquefiable soil exist beneath the channel. Furthermore, tidal-influence prevails against the channel levee. Implementation of a successful design for channel improvement emerged after several traditional concepts were deemed unacceptable by geotechnical consultants. OC Public Works (on behalf of OCFCD) was in need of a design and construction technique that mitigated many associated risks. From these circumstances, Soil-Mix-Sandwich was born and was referred to in the rest of this discussion as SMS. OC Public Works required the SMS design concept to undergo verification by independent geotechnical consultants. SMS chronology from conception to construction can be summarized as follows:"

Jan 1, 2015

By Mario Mauro

In 2007 the US Army Corps of Engineers classified the Herbert Hoover Dike in Florida as a Dam Safety Action Classification (DSAC) 1 dam, and started the implementation of one of the largest dam rehabilitation projects in the nation. The construction of the cutoff wall is a key feature of this rehabilitation work to upgrade the dike to current dam safety criteria. The cutoff wall installation is currently being completed on Reach 1, which extends from Port Mayaca to Belle Glade, under a Multiple Task Order Contract based on performance specifications and stringent verification criteria. For the construction of the cutoff wall TREVIICOS selected the self-hardening slurry method. Since the cutoff wall is installed through a layer of highly variable limestone with Unconfined Compressive Strength (UCS) up to 14,000 psi, the excavation requires the use of the hydromill equipment. This is the first successful application of the hydromill technology with self-hardening slurry in a large scale project in the US. This paper presents the details of the method utilized, the quality control procedures, and the experience gained over seven miles of cutoff wall installed.

By Ali Ebrahimi, Meena L. Viswanath, John F. Beech, Mustafa B. Erten, Ming Zhu

"Excessive deformation of a cantilever sheetpile wall can occur due to dredging, excavation, backfilling, or long-term creep behavior of soil. A buttressing berm constructed in front of the wall can be considered as a mitigation technique to prevent or decrease the deformation by increasing the passive earth pressure and thus improving the wall stability. The effect of the buttressing berm on the stability and deformation of a sheetpile depends on the berm geometry (i.e., the thickness/depth and the width) as well as the properties of the sheetpile and the adjacent soils. A parametric study was conducted using a conventional limit equilibrium method. Design charts were prepared to evaluate the effect of a buttressing berm and the soil friction angle on the wall stability and deformation. These charts can be used as a tool by geotechnical engineers to make a quick estimate of the required size of a buttressing berm in case of calculated or unexpected excessive deformation of a sheetpile. An analysis of the effect of a buttressing berm on the stresses and deformation of a sheetpile was also compared with the results from finite element analysis. The results of this comparison are discussed.INTRODUCTIONCantilever sheetpile walls are commonly used to support excavations. Sheetpiles are hot rolled or cold formed sections of steel made to interlock with adjacent sections to form a continuous structure providing lateral support. Sheetpile walls can be cantilever walls or anchored with tiebacks. To construct a cantilever sheetpile wall, sheetpiles are driven by pile drivers or vibrated in to a design depth sufficiently below the depth of excavation. Excavation can then proceed in front of the sheetpile wall, which resists the earth pressure loading from behind the wall. The design depth and geometry of the sheetpile wall depend on the soil conditions, the depth of excavation, and the tolerable deformation. In certain cases, when a small buttress of soil can be left immediately adjacent to the sheetpile wall, the required depth or geometry of the sheetpile wall can be reduced or adjusted, which can significantly decrease the cost of procuring and installing the wall. Such a buttress can also serve as a short-term or long-term remedy in case of observed excessive deformation in a constructed wall. Traditional methods of analyzing the stability of a sheetpile wall do not account for the passive pressure effects of this small buttress. In this paper, a parametric study was performed for a variety of soil types and wall and buttress geometries by implementing traditional limit equilibrium methods in commercial software and design charts were created illustrating the effect of a buttressing berm on sheetpile deflection. Selected cases were then modeled in a finite element software to compare the results with the traditional limit equilibrium method. The resulting design charts can be used as a tool by geotechnical engineers looking to reduce the design geometry of a sheetpile wall or address observed excessive deformation in a constructed sheetpile wall."

Jan 1, 2016

By Sunil S. Basarkar, Vinothkumar S

Ground Improvement Techniques serves to improve various engineering properties for supporting various foundations. These may be undertaken either by conventional or advanced methods. The Controlled Modulus Column (CMC), also known as Rigid Inclusion is a soil improvement technique to reduce the total and differential settlement by using semi-rigid soil reinforcement columns. The CMC technique can be executed by displacement or non-displacement methods. It does not aim to bypass the compressive layer or to install a pile that will directly support the entire load from the structure. Principle of the technique is to introduce a load transfer platform between the head of the column and structure and transform a uniform load into soil. Initially, the structural load transmitted into the soil generate the settlement greater than CMC piles. When the settlement between the soil and column became equal at neutral point, maximum structural load shall be balanced by the positive friction and tip resistance to stabilize the foundation without exceeding the allowable settlement limit. This paper describes the behaviour of soil reinforcement with CMC column and their installation process with reference to a project at the Dry Bulk Terminal Port, San Pedro- Abidjan (Western Africa). Methodology of CMC, requirements of Ground Improvement, arrangements and outcome of this method are presented in this paper.

Sep 1, 2022

By Charles G. Crans, Naresh Gurpersaud

"Toronto’s Union Station, a National Historic Site occupying an entire city block, is the busiest commuter rail transportation hub in Canada. An extensive project is being undertaken to revitalize Union Station while maintaining the historical significance of the building and minimizing disruption to commuters. A significant stage of the revitalization involves excavation indoors, to a depth of up to 5.5 m below the existing floor level to create space for a new transit concourse and a new lower-level pedestrian retail concourse. A hybrid excavation support system utilizing micropiles as soldier piles was constructed over an 18 month period between 2010 and 2011.Development and testing of connections between the micropiles, shotcrete facing, lagging, walers, and tiebacks presented significant challenges. The existing viaduct structure was constructed in the 1920’s on land reclaimed from Toronto Harbour, so there was significant (and ongoing) uncertainty with respect to buried obstructions including relic timber wharfs and abandoned steel and timber piles. Collectively all these conditions precluded the use of conventional methodology; new techniques, installed using modified equipment, and for the first time in the Greater Toronto Area, were required.Details of the existing site conditions, installation challenges, design, construction and performance of the hybrid excavation support system inside this historic structure are presented.INTRODUCTIONUnion Station in Toronto, Ontario is the busiest passenger rail facility in Canada, with 65 million passengers annually and an average of 200,000 passengers each day. Construction of the station was completed in 1920. It has been designated a National Historic Site of Canada and inducted into the North America Railway Hall of Fame in the Facility and Structure category.The Union Station Revitalization Project (USRP) was tendered in 2010 and awarded as a 6-year, $450M construction management / trade contract package. Included was a large scale grade reduction, referred to as “The Dig Down”, to create two basement levels and this required extensive excavation support constructed entirely indoors within the active station setting."

Jan 1, 2017

By Ronald Damen, Dion Denes

"Friction fatigue is the loss of soil-pile friction around the shaft area of the pile. It has been observed during impact driving of piles, and has been modelled to a limited degree using physical scale models. This paper proposes the use of high strain dynamic pile testing to assess and quantify friction fatigue in impact driven piles. The method is applied to two case studies: one on a project off the north-west coast of Australia and one on a South Pacific Island. On both sites calcareous sand layers are present. Pile Driving Analyzer (PDA) monitoring has been conducted during impact driving of steel piles, which allowed for assessment of shaft resistance development both with depth and with progressive driving, by use of wave equation signal matching. Lessons are drawn from the case studies to improve future observations.INTRODUCTIONFriction fatigue is the loss of soil-pile friction around the shaft area of the pile, under cyclic loading or during pile driving. The phenomenon has been frequently observed in some non-silica sands, such as pumice sands and calcareous sands and has been the subject of academic study.The occurrence of friction fatigue impacts the driving behaviour of piles and the shaft friction component of the ultimate geotechnical strength (Rd,ug). If potential friction fatigue is not recognised in the design phase of a project, required pile toe levels can be significantly underestimated. This could lead to extra cost and delays, or, if no adequate pile verification is conducted, to geotechnical failure or underperformance of piles. This is especially true in remote locations, such as Pacific islands, where calcareous material is often present.A better understanding of the phenomenon would aid both pile design and driveability assessment. This paper proposes the use of high strain dynamic pile testing to assess and quantify the effect of friction fatigue from impact driving. Two case studies are presented in which high strain dynamic testing has been conducted on driven piles in calcareous sands to illustrate the method.BACKGROUNDFriction fatigueThe geotechnical strength of piles is composed of the resistance to static loading by the base of the pile and the shear resistance between the shaft of the pile and the adjacent soil. The latter is often referred to as the shaft resistance or shaft friction.During impact pile driving, a decrease in shaft resistance is often observed. Although this phenomenon is also observed during vibratory pile installation, this paper deals predominantly with impact driving. This decrease in material strength from the tip of the pile influences the shaft resistance and may be either temporary or permanent. Temporary reduction in shaft resistance is common in cohesive soils and is thought to be caused by excess pore water pressure, which has insufficient time to dissipate. This phenomenon, commonly referred to as set up, is observed to a significantly lesser extent in non-cohesive materials such as clean sands (Rausche et al., 2004)."

Jan 1, 1900

By Arpana P. Sabu, Themis Vaxevanis, Sissy Nikolaou, Guillermo Diaz-Fanas

Geo-failures from extreme events (landslides, wild fires, earthquakes, floods, etc.) have increased exponentially in recent years around the world and within the USA. When catastrophic failures occur, they usually involve hundreds of fatalities especially in cases of unexpected triggering events, such as large intensity earthquakes or heavy flash floods. Protective actions against identified potential geohazards can mitigate the associated risks and the future occurrences and prevent these occurrences from becoming disasters, targeting the essence of resilience in geotechnical engineering. Imaging and other virtual design and construction tools can be used to identify weaknesses that trigger geohazards and can, in combination with numerical simulations, guide decision making. In spatially distributed problems, 3D visualization and LiDAR-type of technologies are essential in providing geotechnical engineers a deeper understanding of precarious soil zones and support finding appropriate solutions. This paper will present the value of using virtual design and construction technologies though the case study of the Iztapalapa suburb of Mexico, about 20 km southeast of Mexico City. Iztapalapa was developed within irregular topography and has a long history of severe soil subsidence. Following the 2017 Puebla-Morelos earthquake, the town experienced large settlements resulting in extensive damage to the already frail buildings and unregulated infrastructure. The soil subsidence was visualized by mapping available historic and geotechnical data. The visualization helped to identify areas where additional investigations were needed. Additionally, this paper presents a case study of a series of landslides from the 2016 Mw7.8 Muisne Ecuador Earthquake, which demonstrates the advantages of using novel technologies to collect data and create cloud datasets from drones and digital photos to understand and evaluate geo-vulnerabilities in anticipation of an extreme event and during rapid reconnaissance to plan for long-term instrumentation, which can enhance geo-disaster prevention and overall community resilience. INTRODUCTION Iztapalapa is a southeastern borough of Mexico City (CDMX) located within the Mexico Basin (Figure 1). This borough is a densely populated area of CDMX with a total of 1.8 million inhabitants, and has a third of its population living in poverty (Gonzalez-Hernandez et al., 2015) with limited to no access to clean drinking water. Iztapalapa also suffers from high rates of crime, drug trafficking, sex trade and illegal buildings. As the population continues to grow, the already non-regulated and fatigued infrastructure is unable to meet the community needs, especially during and after natural hazard occurrences. The region of CDMX is one of the world’s most seismically active regions that is also exposed to other geo-hazards such as floods, volcanic eruptions, and continuous settlement due to water pumping that has reached 11 meters over the past 100 years (Nikolaou et al, 2019). While the soil subsidence alone has caused significant infrastructure damage in Iztapalapa and throughout the rest of the city, recent earthquakes have also contributed to those damages.

Jan 1, 2019

By Teresa M. Bodas Freitas, Arianna Lupattelli, Peter J. Bourne-Webb, Diana Salciarini, Martina Zito, Donatella Sterpi

The thermomechanical response of thermally-activated (TA) piles under monotonic thermal loads is quite well understood and the remaining uncertainties relate to the effect of long-term, cyclic loading of individual TA piles and pile groups. Recent studies undertaken by the authors have provided insights into the behaviour of TA pile foundations undergoing cyclic thermal loading. Despite their simplicity, the analyses show that key aspects of the observed response of piles in sand, under cyclic thermal loading can be reproduced, providing confidence in the outcomes of the analyses. The studies examined isolated piles and pile groups, and concluded that irrecoverable thermally-induced settlement may be mitigated through the choice of an appropriate margin of safety on the pile shaft resistance under service mechanical load conditions, and the maximum thermal stress can also be readily estimated. This paper consolidates these works and provides guidance regarding the safe geotechnical and structural design of the piles, then looks towards the remaining issues around the safe provision of thermally-activated pile foundations.

May 1, 2022

By Sailesh S. Author

The current design method for soil-cement (SC) columns improved soft clayey ground under the highway embankments assumes a slip circle failure surface shearing through the columns and the soils using a weighted average shear strength. However, the results from the laboratory centrifuge model test and numerical analysis indicate that in many cases, the SC columns fail by bending. Some researchers have proposed methods for estimating the maximum embankment loading for bending failure of SC columns, but those methods have limitations in correctly considering the internal shear stresses or not applicable for the group SC column improvement. Numerous model embankments on SC columns have been simulated by three-dimensional (3D) finite element analysis (FEA) and the mechanism of bending failure and the magnitude of the bending moment in the SC columns under embankment load has been investigated. Based on the simulated results, the design method for the estimation of the bending failure of floating SC columns has been proposed. The predicted results from the proposed method agreed with the existing field condition of one embankment in Saga, Japan reported in the literature in terms of the stability of columns. Hence the proposed method can be used for the design of floating SC columns in the soft ground.

By Brian Wilson, Franz-Werner Gerressen

"Cutter Soil Mixing, also known as CSM, was developed in Europe as an alternate method of Deep Mixing to the more traditional single and multiple auger techniques, and brought to market by Bauer Maschinen GmbH (Bauer), towards the end of 2003. Initial development of the technique had been completed in a joint venture between Bauer and Bachy Soletanche. In 2004 the concept was introduced to the North American market. Continued development of the method and demonstration of its versatility, both in terms of applications and applicable soil types has seen a steady growth in the number of designs incorporating the approach, and contractors offering the technique. This paper provides a brief overview of the variety and size of projects and applications where the method has been adopted, discusses some lessons learned with respect to equipment operation as well as the improvements that have been introduced to the equipment, and briefly reviews the current state of practice, as well as some of the associated on-going research and development.BACKGROUNDCutter Soil Mixing (CSM) is a technique for deep soil mixing that was initially developed as a collaborative effort between Bauer Maschinen (Bauer) and Bachy Soletanche, but which ultimately resulted in the separate development of two somewhat different brands of CSM tool. The Bauer brand of CSM entered the European market in 2004, and was first promoted in the North American market in late 2004, with the first project starting in 2005. The Bachy Soletanche brand, sometimes referred to as “Geomix” was first marketed in Europe in 2005 and the first model introduced in North America in 2007.The development of the Cutter Soil Mixing technique utilized the experiences gained from Trench Cutter/Hydrofraise equipment, developing a technique that incorporates two cutting wheels rotating about a horizontal axis as opposed to the more conventional deep soil mixing approach which utilizes augers and mixing paddles rotating about vertical axes. Whereas the Trench Cutter/Hydrofraise technique excavates the soil from within a panel, and supports the open hole using a bentonite slurry, the CSM technique cuts and displaces the soil whilst pumping a slurry/grout directly into the soil through a port located between the wheels. The combination of cutting the soil while introducing an appropriate volume of slurry effectively fluidizes the column of soil around and above the cutter head. While this process achieves a high degree of mixing, even on the downward cutting stroke, thorough in-situ mixing typically occurs on the withdrawal stroke, when most of the slurry is added."

Jan 1, 2015

By Brandon T. Buschmeier, Sonia S. Swift, Michael P. Walker, Frederic Masse

"Ground improvement has undoubtedly become a cost-efficient and effective solution to support the development of poor soil sites. Ground improvement elements, such as Controlled Modulus Columns (CMCs), replace piles by improving the subsurface soils and reducing settlement. As ground improvement becomes more popular, the applications become more creative and ground improvement is being used to control settlements under large structures with tight settlement tolerances.In this paper, we will discuss the use of CMCs to support two (2) large industrial warehouses where soil conditions would normally lead to the use of deep foundations and a structural slab, grade beams, and hung utilities to prevent excess settlement. Each of the sites we will discuss had poor soil conditions in the form of very soft or compressible soil, heterogeneous fill of varying thickness, and environmental contamination. At each site, we developed a design that would allow for the use of Controlled Modulus Columns (CMCs) with a Load Transfer Platform (LTP) in place of the previously-proposed deep foundations. The use of the CMCs also allowed for the use of spread footings and slab on grade construction. The benefits of this value-engineering approach include economy in the foundation system, risk mitigation by not disturbing contaminated soils requiring expensive removal, and ease of access for future sub-slab upgrades with new tenants. Additionally, the use of recycled concrete aggregate as an LTP is more environmentally friendly than placing structural slabs with heavy steel reinforcement.Designing for the settlement of large warehouses is challenging because it requires changing how we typically perform our designs. For most structures, the slab loads are relatively light when compared to the footing loads, whereas for warehouses, the slab is heavily loaded compared to the relatively light footing loads. Thus, it becomes essential to perform three-dimensional analyses to confirm that the proposed CMC layout will provide uniform support of the slab and footing across a variety of loading scenarios (loaded bays vs unloaded or travel bays). The complexity of the designs for these warehouses generated interest in conducting large area load tests over a grid of multiple columns. The performance of the area load tests provided invaluable information on the effectiveness of the LTP and CMC spacing. In this paper, we present a general description of CMC ground improvement, the differences between ground improvement and traditional pile foundations, our typical design methodology for CMC design, and the modifications to that methodology for warehouses."

Jan 1, 2017

By Shyam Chengalath, Johan Jeansson, Magnus Hörman

Down-The-Hole (DTH) drilling usually uses compressed air to power the hammer. However, there are now DTH hammers on the market which instead of compressed air use high pressure water to power the hammer. There are several benefits with using water DTH compared to air DTH, which are discussed in more detail in this paper. From a physics point of view many of the benefits arise from the fact that water is an incompressible media and air is not. Energy consumption is roughly a quarter compared to air, resulting in lower carbon emission and a lower energy bill. In the case of water DTH the water leaving the drill bit in the hole is at a low velocity and ambient pressure. However, with air DTH the air leaving the drill bit in the hole is at a high velocity and high pressure. This means that the risk of damaging surrounding structures in sensitive areas such as urban environments and dams, is greatly reduced with water DTH. In this paper two cases where water DTH is used in jet-grouting applications are discussed in detail. As these cases show there is a clear improvement in productivity when using water DTH hammers.

Sep 1, 2022