Search Documents

By Michael Bauer

Increases in productivity and improvements in mining occupational safety and health are intrinsically linked. Over the past years, the German Hard Coal Mining Industry has been able to accomplish both: an increase in coal production and, at the same time, a significantly reduction of accidents. This success has been achieved by advances in technology, better organization and investment in people. Since 1990 productivity has more than doubled, while the total number of accidents has been reduced by more than 90%. Further development started initially with the mechanisation of the winning and drivage technology. Innovative technology and standardisation of the mining equipment were one reason for the increase in productivity and reduction of the accident rate. Therefore this technical development was not only one important pillar of the TOM model explicated later but also the requirement for the successful development of the other pillars. In addition to further developing this innovative technology it was possible to realise procedural and organisational improvements. As a result, the above achievement is based on implementing the three pillars of the so-called "TOM" model (technology, organization, ?Mensch? = human). To increase safety, improve performance, raise awareness and change of employees? attitude, the following technical and organizational requirements have been introduced: ??New innovative technology and procedures, standardized techniques and better equipment. ??Measures to revise or redefine the organizational structure, processes and systems of work, which were then integrated into the company policy and procedures as a company management tool. ??Personnel measures (investment in people). These include, improving motivation and behaviour, training, communication to raise and to change awareness of safety issues. Success in Occupational Health and Safety is not an automatic or self-regulating process. It needs hard work to make improvements and it must be treated as a recurring cyclic process. As a result of the above, occupational health and safety has become a natural part of daily work in the German Hard Coal Mining Industry. This could only be achieved by the unconditional "commitment" of all managers and employees to the issues, coupled with discipline and responsible action. Further improvements towards the ultimate aim of "zero" accidents are only possible by mutual involvement in implementing the ?TOM? (technology, organization and ?Mensch? human) model.

Aug 1, 2013

By Chris McBean

Due diligence mistakes ? lost opportunity ? High profile write-downs and cost overruns ? Result ? tight market for financing ? Implications for due diligence ? need to get it right ? maybe only one chance ? Where should focus be?

May 1, 2013

By José J. Suárez

Abstract: Globally, the mining industry is expected to face the following challenges through 2020: 1. Sustaining growth amidst fierce competition 2. Containing cost increases and managing through the cycle 3. Attracting and retaining talent 4. Managing environmental concerns and improving sustainability 5. Managing volatility risks in commodity markets Our experience and research reveals that the higher performing global miners are adopting many of the following strategies: (1) Adopt a Global, Agile Operating Model (2) Be the Developer of Choice (3) Drive Capital Efficiency (4) Be the Employer of Choice (5) Integrate the End-to-End Business Model (6) Move to the Virtual Mining Value Chain This paper/presentation will provide data obtained through research on five (5) challenges facing the mining industry, and on the six (6) strategies that high performing global miners are adopting.

May 1, 2013

By R. Llewellyn

"Wear damage is responsible for very high maintenance costs and significant production losses in the oil sands industry of northern Alberta.It affects all areas of operations and involves a panoply of wear mechanisms from low stress sliding abrasion at extremely frigid temperatures during winter mining, to elevated temperature erosion/corrosion in processes where bitumen is converted to lighter hydrocarbon products.There is no universal panacea to defend against such diverse attack and a wide selection of resistant materials and systems is employed. These range from relatively soft rubbers which rely on their elastic properties for their protective capability, to some of the hardest ceramics and cermets which are currently available commercially.Details are presented of the characteristics and forms of the variety of wear materials being used and how they relate to the requirements of their areas of application. The review focuses on the practices followed at Syncrude Canada Ltd., which is the larger of the two commercial oil sands plants."

Jan 1, 1997

By P. C. McLeod

THE GECO OREBODY, located north of lake Superior in the Thunder Bay district of northern' Ontario, was discovered in 1953. Diamond drilling in the following year indicated a 15,000,000-ton ore-body, and production plans were made for the shipment of copper and zinc concentrates in three years. To accomplish this, the Geco Project was initiated. The property was in an undevdoped, inaccessible area, and the project involved the conversion and extension of a logging road to the property, the construction of two railways and seventy miles of hydro transmission line, the erection of a municipality, the building of a plant, and the development of an underground mine to produce 3,300 tons per day. This paper describes some of the methods used in the underground development phase of the Geco Project.

Jan 1, 1958

By L Thompson, R C. West, T S. Kho

In 1978, the Outotec direct to blister flash (DBF) smelting process was commercialized with the commissioning of the Glogow 2 smelting facility in Poland. Since then four further DBF facilities have been constructed, two at Olympic Dam, one in Zambia and most recently one at Glogow 1 in Poland. The DBF smelting process differs considerably from conventional smelting process in both chemistry and unit operations, presenting opportunities for flowsheet capital and operating cost savings particularly when the concentrate copper grade is high. WorleyParsons has amassed considerable expertise in the Direct to Blister process and in this paper the process is compared to the modern two stage Double Flash process. The processes are modeled, and the key operating parameters, consumables and production metrics are directly compared. Subsequent flowsheets, key equipment lists and capital costs are also presented for comparison and discussion. The results show the range of concentrates which are most economically treated by the DBF process relative to those best treated in conventional processes along with those concentrates which could be treated by either process. INTRODUCTION The Outotec Direct to Blister (DBF) process was developed and installed at Glogow in 1978 (Czernecki et al., 2006). Currently there are a total of five DBFs built on three sites: Glogow No.2, Olympic Dam No.1, Olympic Dam No.2, KCM Zambia and Glogow No.1, being the most recently constructed. The DBF process was the first flash furnace process to produce blister copper and paved the way for the subsequent development of the flash converter and other continuous converting processes. Today four flash converters are in operation taking the total number of flash furnaces producing blister copper to eight. In all DBF operations it is the unique ore and concentrate composition which made selection of the DBF process the most attractive. In all cases, the concentrate is relatively high in copper but low in iron because chalcopyrite is not the major constituent. When considering smelting options for high copper, low iron concentrates a key question is then often asked, “At what point does it become economic to switch from two stage smelting and converting process to the DBF process?”

Jan 1, 2019

By M. V. Rowley, D. D. Warkentin

With high commodity prices, tightening operating budgets and increasing disposal costs, there is an increasing interest in processing municipal waste streams, such as the ash derived from combustion processes. This paper describes laboratory development work for a process to recover metal values from the finer fractions of these wastes. The work was initially aimed at recovery of copper and the removal of lead and other heavy metals from the ash residue, but results showed gold and silver recovery to be an important objective as well. The process uses gravity and flotation as the principal separation steps, with gold recovery occurring mainly in the flotation stage. The particle size range and chemistry of the ash presented numerous challenges to developing a suitable flotation method, but an effective flowsheet was developed by separating the ash into a fine fraction and a separate slime fraction, each with a unique flotation strategy. Specialized conditioning stages and careful reagent selection have resulted in effective gold and silver recovery from a range of ash types and sources. The work has resulted in a patent being issued for a process based on this novel approach to the treatment of combustion wastes.

Jan 1, 2017

Vast quantities of cosmic material, ranging in size from fine dust to large meteorites and planetoids, have been colliding with and accumulating on the earth since its origin 4.5 billion years ago. There are less than twenty well preserved meteorite craters and Jess than thirty fossil craters or astroblemes on the present face of the earth. On the moon, there are approximately 200,000 craters on the visible face alone -the largest crater being 132 miles in diameter and attaining a depth of 16,000 feet. Making allowances for the different physical conditions on the moon and assuming that these lunar features are of impact origin, the indifference is that, since primeval time, large numbers of celestial objects have also encountered the earth, but that both the topographic expression of the impact and the objects themselves have been destroyed by weathering and erosion. It may be reasonable to suggest that additions of cos-mic bodies have materially altered the chemistry of the earth's crust from place to place and that the impact of large meteorites and asteroids has created zones of weak-ness in the crust that could be the center of magmatic intrusion and mineralization.

Jan 1, 1965

By J. F. Wright

Gold-bearing quartz veins and replacement chalcopyrite deposits are the two important types of metallic mineral deposits of the east central Manitoba mining district. The gold-bearing veins occur along Manigotagan valley, northwest for 25 miles from Beresford lake, and the copper deposits along Oiseau valley, between Oiseau lake and the east end of Lac du Bonnet. Lithium-bearing minerals of possible commercial value have recently been discovered in pegmatite along Winnipeg river about 10 miles east of Point du Bois. There are also prospect pits with showings of galena, sphalerite, cobaltite, pentlandite, nickeliferous pyrrhotite, arsenopyrite, pyrite, molybdenite, cassiterite, and other minerals, but the various occurrences of these minerals, as exposed, are small. The bedrock and mineral deposits of this mining district are Precambrian and resemble in many respects the formations and mip.eral occurrences of western and northern Ontario. Although prospectors visited eastern Manitoba at intervals during the last fifty years, effective prospecting did not begin until 1913 or 1914, and not until 1923 were skilfully directed, systematic explorations undertaken. It is true, that between 1913 and 1923 considerable sums were expended in a number of attempts at mining and milling the gold-quartz ore, but these enterprises failed partly through poor management or attempts to develop veins that were too small or too low-grade to be worked at a profit under the existing conditions of transportation and power supply.

Jan 1, 1925

By W. E. Hale

An area of about 7,000 square miles within the eastern part of the Grenville Sub-province is underlain chiefly by granitic gneisses. There are, however, some exposures of mafic rocks which warrant further investigation, and some attractive structures, particularly basins, which deserve additional economic consideration. T HIS paper describes in a very general fashion the economic and geological features of an area of about 7,000 square miles on the north shore of the Gulf of St. Lawrence in the eastern part of the Grenville Sub-province (Figure 1). The scarcity of published geological data on this part of the Cana-dian Shield (DePuyjalon, 1899 and Longley, 1944) justifies the presentation of these tentative results. It should be appreciated, however, that the information which follows was acquired in a rapid reconnaissance designed specifically to out-line what might be interpreted as favourable geological environments for the occurrence of economic minerals, rather than to produce an authoritative analysis of the geological history of the region.

Jan 1, 1962

By D. F. Zhang, X. Q. Jiang, N. Tahreen, D. L. Chen, F. S. Pan, D. Y. Li

Alloying with rare-earth elements has been proven to be an important tool for magnesium to achieve superior properties via texture randomization. The role of yttrium in texture weakening and the link between texture and formability are fairly well known. Since annealing is a vital part of metal processing which could significantly contribute to ductility, it is important to ascertain the impact of annealing in terms of texture change. Also, an understanding about texture development during pre- and post-deformation annealing is essential to improve the industrial deformation processing as texture is closely related to formability. While there is independent information in the literature regarding the effect of rare-earth addition and heat treatment on the texture formation, no systematic studies have been reported on the collective impact of yttrium addition, annealing and deformation on texture evolution. The present study was, therefore, aimed to identify the inter-relationship among texture evolution, yttrium content, heat treatment and deformation behavior in an extruded Mg-Zn-Mn-Y alloy. Annealing at 450°C for 1 hour and uniaxial compression tests at a certain amount of deformation were performed. The deformed and annealed samples were then subjected to annealing and compression test, respectively, followed by texture measurements. It was observed that yttrium addition effectively weakened the crystallographic texture in all conditions, which was evident from the changes in the microstructures and textures.

Jan 1, 2015

By M. Potesser

Higher prices for natural gas or oil have motivated the copper industry to reexamine the modes of oxygen and oxy-fuel burner usage at operating plants. With rising energy costs and the growing importance of environmental protection, burner usage and burner operations have become the focus of several investigations and optimization efforts. One possible approach to lower energy usage is through combustion using tonnage oxygen. When such oxygen is used, the flame temperature increases and operational efficiency is improved. As well, with the correct technology, due to the presence of lower levels of harmful substances such as NOx in the off gas, there is improved environmental performance. As regards copper production, furnaces are employed for both concentrate smelting or for melting and casting operations. The use of tonnage oxygen in concentrate burners for smelting provides for a higher thermal efficiency. For furnaces employed for melting, air-operated burners may in fact have an initial advantage because a long radiant flame is typically generated, thus providing for a higher degree of heat transmission. This paper describes the new experimental burner chamber of Messer Austria GmbH which provides for testing of the combustion of natural gas with oxygen or oxygen-enriched air and the use of special water cooling ducts that simulates a metal charge during melting, The operational effectiveness of the burner is determined from temperature and off-gas analysis data. The paper also discusses future trends in burner technologies including a new patented burner. Cu2007 - Volume III (Book 2) The Carlos Diaz Symposium ou Pyrometallurgy Edited by A.E.M. Warner, C.J. Newman, A. Vahed, D.B. George, P.J. Mackey, A. Warczok Toronto, Canada,

Jan 1, 2007

By R. Lodha, C. Oprea, G. Oprea, H. Zargar, T. Troczynski

"The basic refractories used in non-ferrous industry contain chrome ore for improving the thermal shock resistance, thus reducing the penetration of molten metal and fayalite-type slags into the lining. The current study aims to replace chrome ore with Me4+ ions along with Fe3+ ions in order to form MgO-Al2O3- FeOx-Me4+O2 based complex spinel systems that could perform similar to the complex chromia-bearing spinel in the magnesia-chrome refractories. This system allows for lower temperatures of synthesis and sintering. In our study, compositions with 60% MgO were fired below 1500°C and resulted in complete formation of complex spinel, and open porosity less than 5%. The in-situ formation of the complex spinel from the fine mix of oxides in the MgO-Al2O3-FeOx-Me4+O2 system offers a suitable alternative of binding system to produce basic refractories at lower temperatures and of similar physical and mechanical properties with magnesia-chrome bricks fired above 1750ºC. INTRODUCTIONThe synthesis of magnesium aluminate spinel (MgAl2O4) (Maschio, Fabbri, & Fiori, 1988) or magnesium chromate spinel (MgCr2O4) from their respective oxides is diffusion controlled resulting in a sluggish reaction even at high temperatures. For instance, the diffusion of Mg2+ and Al3+ ions in the intermediate spinel layer during reaction is slower than the diffusion of Mg2+ in corundum and Al3+ in periclase. The interfacial layer of spinel formed during the reaction increases the diffusion path for the spinel forming cations. This accompanied by ~8% volume expansion retards further reaction resulting in incomplete spinel forming reaction during sintering and hence densification during the reaction cannot be achieved. In order to assess sintering studies with fine particulate oxides that would result in a lower diffusion path, a mechanical mixture of the hydroxides of aluminium and magnesium calcined at 1400ºC to 1600ºC for 1 hour does not result in complete spinel formation (Sarkar, Das, & Banerjee, 2003), which indicates that reaction sintering of stoichiometric magnesium aluminate spinel is retarded by initial reaction forming the interfacial spinel layer. The basic bricks used as linings in non-ferrous pyro-metallurgical convertors are manufactured using magnesia and chrome ore, the sintering of which produce spinel solid solution. This solid solution is a mix of both normal and inverse spinel structures that sinters at temperatures in excess of 1800ºC in air."

Jan 1, 2012

By R. K. Mishra, A. Kula, X. Jia, M. Niewczas

The mechanical properties of Mg-Gd and Mg-Y solid solutions have been studied under uniaxial tension and compression between 4K and 298K. The results reveal that Mg-Gd alloys exhibit higher strength and ductility under tension and compression attributed to the more effective solid solution strengthening effect and grain boundary strengthening. Profuse twinning has been observed under compression, resulting in a material texture with strong dominance of basal component parallel to compression axis. Under tension, twining is less active and the texture evolution is affected mostly by slip. The alloys exhibit pronounced yield stress asymmetry and significantly different work-hardening behaviour under tension and compression. Increasing of Gd and/or Y concentration leads to the reduction of the tension-compression asymmetry due to the weakening of the recrystallization texture and more balanced twinning and slip activity during plastic deformation. The results suggest that under compression of Mg-Y alloys slip is more active than twinning in comparison to Mg-Gd alloys.

Jan 1, 2015

By M. Grenon

"The presence, size, orientation, nature, and persistence of geological discontinuities dictate the behaviour of a rock mass. Block size, which is defined by discontinuity spacing, by the number of joint sets, and by the persistence of the discontinuities delineating potential blocks is an important indicator of the degree of fracturing of a rock mass. Consequently, block size is represented either explicitly or implicitly in all rock mass classification systems employed for analysis and design of surface and underground mining structures. Insitu block size distributions may provide a better means to describe the structural complexity of a rock mass. These are the distributions that would be derived if the in-situ rock mass was separated into its constitutive blocks, delineated by existing discontinuities, and each block measured. This paper presents the results of a field campaign at Louvicourt Mine aiming to characterize the rock mass using different methods for determining block size and block size distributions. IntroductionGeological structural data are used to provide input data for analysis and design methods for surface and underground structures. As the collection of structural data involves considerable investment of time and effort, it is sometimes overlooked, thus denying an important source of information for mine design. What is somewhat surprising, however, is that when structural data are available, they are not used to their full potential. Recent work has shown that data on block size have potential applications in different areas of rock engineering:• Blasting — Hudson (1993) has described the excavation process as the change of a preexisting natural block size distribution to the debris fragment size distribution (Fig. 1). Lizotte and Scoble (1994) have reviewed previous efforts on integrating site specific geological conditions into blast design. Grenon et al. (1997) provide a case study where in-situ block size distributions are compared to photogrammetric studies of blasted rock.• Rock mass classifications — Block size is used in the majority of rock mass classification systems either explicitly, as in the RMi classification system Palmstrøm (1995), or implicitly, such as in the NGI system, Barton et al. (1974)."

Jan 1, 1998

By T L. Horsley

This paper deals with the drilling and blasting methods employed at the Cassiar mine, which is located just south of the B.C.-Yukon border. It covers both the "pit" and "peak" mining operations. Specific problems, such as working in frozen ground, are discussed, and the breaking characteristics of the various rock formations are outlined. The paper concludes with a brief mention of the equipment used in the operation, as "~ell as an outline of the breaking costs. Introduction T HE Cassiar asbestos mine is located just south of the British Columbia -Yukon border high on a spur of McDame mountain. Chrysotile asbestos fibre occurs in a faulted enlargement of a serpentine sill lying conformably be-tween a series of sedimentary beds and volcanic flows which dip at 45 degrees into the mountain. One end of the orebody is eroded by a cirque in which a layer of permanently frozen ore and waste talus lies at the end of the mining benches. The topography at the mine is steep, with no flat areas. Roads, dumps, and areas for crushing,

Jan 1, 1965

By L. Paulino, C. E. Zangiacomi, J. Yamamoto

"This paper presents the learning from Alcoa Po9os de Caldas Smelter in Brazil, after several energy restrictions resulting from the failures of three rectifier units at its power switchyard. Starting on December 27th, fuses and diodes failed in three rectifier units of Potline #1, causing a long and dangerous power interruption. Even after current was reestablished, amperage was only 70% of the line target leading to a bath freezing process that lasted for around 48 hours. The process engineering team played with several potroom parameters as pot resistance, bath and metal levels, alumina feeding and bath chemistry in an attempt to minimize impact on the potline metal output and energy consumption. As it will be illustrated, the first battle was to keep the pots running on a ""survival"" approach. After that, several changes took place on the procedures used to run at reduced current which were considered rather successful. Finally, some recommendations will be given to foresee and prevent transformers and rectifiers from undesirable failures."

Jan 1, 2006

By G. Favini

A Bayesian decision model of minimun risk, based on the probability and costs of mine discoveries and non-economic projects, is presented for massive sulphide exploration in the Canadian Shield. The sample used for the model is composed of data relating to forty mines, sixty non-economic sulphide occurrences, and sixty occurrences of graphitic and pyritic material. These economic and barren samples consist of drill-tested occurrences which were, in varying degree, characterized by conductivity anomalies. Given the large size, the reliability and the homogeneity of the data base available for massive sulphide exploration, it is shown that certain statistical models can and should be utilized as a tool for decision-making by explorationists. Given this data base, information theory tells us that only those signals that are independent of one another will transmit information with minimum error. An ensemble of six significant multilevel signals, markedly independent of one another and consisting of numeric and geometric form descriptions derived from Bouguer anomaly, aeromagnetic and physiographic maps, were identified and evaluated by case studies. The use of these signals as input in a simple statistical procedure, or in a carefully planned and experienced visual appreciation scheme, can be of significant aid in decisions concerning the choice of favourable areas or sectors to explore in detail. The method of discriminant analysis is theoretically and practically suited for the statistical modelling involved. By way of a simulation on our statistical model, the efficiency of the model and of the underlying criteria is determined for historic cases and, by inference, for its validity in future exploration. An approximate optimized solution is derived from the model which suggests that over 90% of the known ore could be found by screening, according to a model such as that herein described, and drilling only 30% of the targets (mostly barren) normally identified and tested in current and past exploration.

Jan 1, 1979

By R. H. Waddington

Historical The limitations of reverberatory furnace operation have prompted many investigators to consider electric furnaces for melting electrolytically refined cathode copper. In the majority of cases where experimental work was performed, the furnace used was of the granular resistor, induction, or indirect-arc rocking type, and attempts to adapt the three-phase direct-arc furnace to copper melting appear to have been relatively few. In 1935, the International Nickel Company of Canada, Limited, carried to an advanced stage its experimental investigation of continuous melting of copper in the three-phase direct-arc furnace, and demonstrated that this process was technologically and economically practicable. Trial operations were conducted at the Huntington, W.Va. works of the Company, and were followed by the installation at Copper Cliff, Ontario, in 1936, of a full-scale unit for commercial operation. Two years later, a second unit was installed -which raised the electric melting capacity to a point permitting complete replacement of the coal-fired reverberatory furnace operation in the production of refined copper castings.

Jan 1, 1946

By E. S. Allen, P. R. Kruesi, J. L. Lake

An electrochemical process is described for converting concentrates of base-metal sulphides to the corresponding pure metals and elemental sulphur. The application of the process to chalcopyrite is discussed. The process is also of potential interest in processing copper-nickel sulphides, and laboratory data concerning this potential are presented. The process creates neither air nor water pollution.

Jan 1, 1973