Search Documents

By N Berkowitz

Slurry pipelining, as now under-stood and practised, can only command marginal interest in Canada, as long-distance railway freight charges in this country are generally lower than slurry pipeline tariffs. Several alternatives to conventional slurry transmission are, however, now emerging, and two such alternatives are briefly discussed with reference to coal pipelining. In one, coal is transported as a suspension in oil; the other contemplates the movement of paste "slugs." Preliminary economic estimates indicate that the resulant process simplification and adoption of common carrier principles could lead to cost reductions that might make Western coal competitive with imported fuel in the power generating stations of eastern Canada. R ECENT appraisals of slurry pipelining techniques, some-what incongruously 'based upon the performance of successful installations (1,2), are making it increasingly apparent that current solids pipelining methods can only command marginal interest as methods of bulk commodity transportation (3). Although some uncertainties remain in matters of detail, it is now generally conceded that long-distance slurry pipelining cannot compete against rationalized railway transportation unless movement of

Jan 1, 1963

By D. J. MacKinnon

"The Canadian Copper Company, formed in 1885, began mining the nickel-copper ores of Sudbury in 1887 and producing nickel-copper matte from its smelter in 1888(1). Although it was quickly appreciated that the separation of nickel and copper (i.e. refining) was critical to the production of a marketable nickel product, refined nickel was not produced in Canada until about 1918. From the beginning of the industry, there was considerable political agitation to refine nickel in the Province of Ontario(2). The companies, however, claimed that the existing processes, viz. the sodium sulphide ""tops and bottoms"" process operated by the Orford Copper Company of New Jersey, U.S.A.(1,3,4) and the carbonyl process(5,6) developed by the Mond Company at Clydach, Wales, were too costly to operate in Canada. Nickel was first refined in Ontario about 1918 when the International Nickel Company opened a nickel refinery at Port Colborne, Ontario(6). Initially, however, the refinery at Port Colborne employed the Orford sodium sulphide process, and the first electrorefined nickel in Canada was produced in 1920 by the British America Nickel Corporation whose mine and smelter were located in Sudbury, Ontario, but whose electrorefinery was located at Deschenes, Quebec, near Ottawa, Ontario. The purpose of this article is to outline the early history of nickel electrorefining and to trace the significant developments which led to the first successful commercial electrolytic nickel refinery in Canada. The development of an electrolytic process for refining nickel is due largely to the efforts of four individuals, viz. Carl Hoepfner, Hans A. Frasch, D.H. Browne and ultimately N.V. Hybinette, and the contribution of each is discussed separately below."

Jan 1, 1999

By M. M. C Jiménez, J. A. S Ténorio

For the recovery of valuable materials and for the protection of environment, recycling process of printed circuit board is an important subject of study. Moreover, the popularization of the computers and its technological evolution has generated a large number of waste electrical and electronic equipment. This paper presents a study of synergistic solvent extraction of copper, nickel and zinc from a sulfuric leaching liquor of printed circuit boards (PCB’s). The percent extraction of copper, nickel and zinc from dilute aqueous sulfate media besides synergistic effect of mixture of the .extractants Cyanex 272 and D2EHPA have been studied. Furthermore, different conditions such as temperature, pH of the feed solution have been examined. The results suggest that the synergistic effect of the .extractants mixture enhance the extraction efficiency of nickel.

Jan 1, 2014

By A. W. F. Smith, P. B. Prangnell, D. N. Crowther, P. J. Apps

It is well known that the refinement of grain size in metals leads to a significant improvement in important mechanical properties. As part of a European collaborative project, processing schedules have been investigated aimed at producing a homogeneous ultra-fine ferrite and spheroidised carbide aggregate microstructure structure in high carbon (CMn) steels (0.6-1.2wt%C), via conventional 'warm' rolling and innovative Equal Channel Angular Extrusion (ECAE). Suitable deformation schedules were determined from dilatometry and thermo-mechanical Gleeble simulations. Evidence of an ultra-fine ferrite and carbide aggregate microstructure following 'warm' rolling is given. A significant improvement in tensile strength, particularly proof stress (0.2%) was also noted in comparison to material deformed at higher temperatures. Concurrent Equal Channel Angular Extrusion (ECAE) experiments investigated microstructural evolution with incremental strain. Extensive analysis was carried out using various techniques, including high resolution Electron Back Scattered Diffraction (EBSD). Evidence of ferrite grain refinement was noted in a eutectoid composition steel. A sub-micron ferrite structure was observed following high strains (E-3.33) and the mechanical properties exhibit a marked increase in tensile strength.

Jan 1, 2004

By D. G. Sinclair

IN surveying the changes that have taken place in the mining industry of Ontario in the past ten years, the striking growth of the gold mining industry first attracts attention. In 1925 there were only twelve regularly producing gold mines in the Province, six of which were located in the Porcupine area, four at Kirkland Lake, and one each at Larder Lake and Boston Creek. In contrast with this, the year that has just closed (1935) has seen production on a steady basis from forty mines, with what may be termed spasmodic production from twelve other properties. This so-called spasmodic production is, however, responsible for the recovery of gold to an estimated value of between $75,000 and $100,000 during the year. Further illustrating the expansion in the gold mining group is the activity in the exploration and development of properties. In 1925, mining operations were conducted at 29 properties which had not reached production, while in 1935 work of this nature was carried on at 87 such properties. It is of interest to note that of the six properties listed as producers in Porcupine ten years ago, five are still producing at rates considerably in excess of the tonnages handled at that time. In fact, the estimated tonnage treated at these mines in 1935 exceeds the 1925 tonnage by approximately half a million tons. In Kirkland Lake, the figures are still more striking. The four mines in production in that camp in 1925 milled 346,584 tons, producing bullion to the value of $5,132,128, while in 1935 these same mines treated approximately 1,643,000 tons, with a recovery of roughly $29,300,000. While Porcupine and Kirkland Lake remain the great gold-producing camps of the Province, the growing importance of the newer areas is readily appreciated when we consider that in 1935 the mills of these areas treated over 1,000,000 tons of ore for a production in excess of $7,500,000. Pro-duction from these newer districts first became of importance in 1930 with the commencement of recovery at the Howey mine, in Red Lake, and the Minto, in Michipicoten. Since 1930, eighteen new gold mills have gone into production in the Red Lake, Little Long Lac-Beardmore, Pickle Crow, Sturgeon Lake, Michipicoten, Sudbury, and Matachewan areas. In respect to silver mining, the period under review has seen a considerable slackening of activity, due to a generally unstable and depreciated price for the product and to the exhaustion of ore reserves in the mines.

Jan 1, 1936

By J. G. Patterson

"The depressive action of sodium cyanide on chalcocite has been investigated and found to be unstable. Flotation results show that with the addition of sodium cyanide to the system chalcocite is initially depressed but rapidly recovers with time, provided there is sufficient oxygen present.lt is proposed that the unstable depression is due to the reaction of cyanide with adsorbed xanthate and copper ions at the chalcocite surface to form soluble copper complexes. When all the free cyanide has so reacted, xanthate anions can then re-adsorb on the chalcocite surface and the flotation will recover. Results are presented to verify the the above mechanism."

Jan 1, 1968

By E. Y. Carlson

"IN A SHORT PAPER it is impossible to do much more than to list the industrial minerals found in Saskatchewan and to give a brief description of the activity associated with each. I will not attempt to discuss the geology. It is sufficient to say that the settled part of the Province is covered by glacial drift which varies in thickness from a few feet to several hundreds of feet, and that this has hindered the search over much of the Province.CLAYA notable exception to this is the Cypress Hills area in the southwest corner which did not suffer any glacial action and where we find some of the large exposures of Cretaceous clays. In this area, the majority of the deposits are of stone-ware clays which are •an excellent raw material for such products as face brick and sewer pipe. Although the clay cannot be transported over any great distance it is used extensively in Alberta and Saskatchewan in the production of these products."

Jan 1, 1959

By E. C. Roper

THE Britannia Mining & Smelting Company, Limited, have been operating their property at Britannia Beach, B.C., continuously for nearly forty years and have mined over 33,000,000 tons of ore from orebodies within a belt of highly sheared rocks, five miles long by 2,000 feet wide. The property is in the Coast Range mountains, about twenty miles due north of Vancouver. The mountains rise abruptly from sea level to elevations of 4, 500 feet within a horizontal distance of 7,000 feet. The topography has enabled the orebodies to be developed by adit tunnels. The active mining levels are connected to the adits by incline and vertical service shafts. The main service adits are the 2200, 2700, and 4100 levels (see Figure 1). The mine surface shops, three bunk-houses, and over one hundred dwellings form the townsite camp at the portal of the 2200 level adit. A small camp of one bunk-house and a few dwellings is situated at the 2700 level portal. The beach surface shops and camp, adjacent to the 4100 level adit, service the mill, foundry, and other beach installations as well as the mining from the 4100 level. The ore mined from the various orebodies is delivered to the 4100 main haulage level through a system of rock raises and intermediate tramming levels and is hauled on the 4100 level to the mill.

Jan 1, 1945

By A. Proulx

Durant les années 1955 à 1961, plusieurs campagnes d?exploration ont été menées sur la zone Bond dans la partie sud-ouest de l?anneau nord de la carbonatite d?Oka (propriété de Niocan, figure 1). Les zones minéralisées HWM1 et HWM2 sont découvertes à l?ouest de la propriété. Un des forages, le S-60, avait intercepté 80 mètres de minéralisation à 0.71% Nb2O5 à l?est des zones HWM1 et HWM2 mais aucun autres travaux d?exploration n?avaient été réalisés sur cette interception minéralisée. En 1995, Niocan réalise une campagne de forage pour mieux définir la zone minéralisée recoupée par le forage S-60. En 1997, une seconde campagne de forage détermine un tonnage de 14.37 Mt avec une teneur de 0.66 % Nb2O5 pour la zone S-60 (Marcotte et Gagnon, 1997). Le complexe carbonatitique d'Oka se situe à environ 35 km à l?ouest de Montréal sur la rive nord du lac des Deux-Montagnes. Sa formation remonte au Crétacé précoce (entre 117 à 123 Ma). La carbonatite d?Oka fait partie de la suite d'intrusions alcalines que constituent les collines Montérégiennes. Le complexe a une forme allongée (7.2 km par 2.4 km) orientée NO-SE (figure 1). Il est intrusif dans des roches précambriennes constituées d?anorthosites au nord et de gneiss charnokitique au sud (Gold, 1963) appartenant à la Formation de la colline d?Oka. Les gneiss au contact du complexe sont fénitisés sur une épaisseur qui peut atteindre jusqu?à 60 mètres. Les roches carbonatitiques forment la série dominante du complexe et elles sont composées principalement de calcite (> 50 %) à gros grain et parfois rubanées. Les minéraux accessoires les plus communs sont la biotite, le pyroxène, la monticellite, la magnétite, l?apatite, la forstérite, la mélilite, le pyrochlore, la pérovskite, la niocalite, la pyrite et la pyrrhotite (Gold, 1963).

May 1, 2003

By W. L. Uglow

In recent years, the microscope has come to be recognized as a valuable aid to engineers whose business is the discovery, development, concentration or reduction of metallic ores. In many of the large treatment plants microscopical research has already an important status; and in the hands of efficient operators the microscope has indicated methods of solving ore problems resulting in the saving of thousands of dollars that otherwise might have been lost in tailings, or expended in freight rates or smelter charges. Failure to procure all the information that the microscope can supply concerning the physical and mineralogical characteristics of complex ores has in many cases led to the construction of unsuitable concentrators, just as the failure to investigate in detail the geological conditions of an ore deposit has often results in the squandering of money on shaft sinking, and mechanical installations which subsequent development of the deposit failed to justify. The great progress recently made in the selective separation of minerals by means of the various processes of flotation and leaching brings strongly to our attention, the scope of the field in which microscopical methods may be advantageously employed. The microscope enables one to observe the minute details of rock, ore, gangue, concentrate, tailing, matte, slag and metal, that are invisible to the naked eye. Furthermore, the technique of microscopal research has been so highly developed that a microscopist can not only observe, but deter-mine the compositions and measure the diameters of the mineral constituents in the ore to be treated. Magnifications of these constituents up to 3,000 diameters may be produced by the proper combination of eyepiece, objective, and projection apparatus, and the images thus viewed may be photographed through the microscope, and permanent records made of them.

Jan 1, 1924

By William James Kempson

This paper discusses ore handling systems in shafts. These are considered from the loading facility at shaft bottom all the way through to the discharge mechanism in the headframe. These systems will be discussed from the following perspective: i. Intrinsic safety of the systems ii. The efficacy of the systems to perform consistently iii. The maintainability of the systems iv. Overall system cycle times Particular emphasis is placed on the following specific areas: 1. The Shaft Bottom Loading Facilities The various shaft loading systems currently in use are discussed, the selection parameters surrounding these are quantified and the specific selection criteria are outlined. 2. The Various Skip Configurations In this section the various skip configurations in use around the world will be described and the specific design details associated with these will be highlighted. The advantages and disadvantages of these systems will be compared and the overall efficacy of these will be discussed. 3. The effect of the loading and skip configurations on the Load Cycle Times. The overall cycle time which can be achieved by a shaft system is strongly dependant by the speed and efficiency with which the ore can be loaded and transported out of the mine. The potential of the various systems to be optimized will be discussed. The emphasis of this paper is to highlight the lessons which have been learned with respect to ore transport system design and provide a common basis against which these can be compared in future applications.

May 1, 2013

By Edward Rybinski

Compañía Minera Antamina is a polymetallic mining complex that produces copper and zinc concentrates as primary products and molybdenum and lead/bismuth/silver concentrates as by-products. In 2007, Metso Process Technology and Innovation (PTI) was contracted to increase SAG mill throughput by integrating and optimising blast fragmentation, crushing and grinding for the harder M4/M4A (CuZn) ores. Following the implementation of recommendations provided by Metso PTI, the SAG mill throughput increased from 2750tph to reach an average of 3600tph for the remainder of 2007. Due to continued application of mine to mill integration and optimisation philosophy, by 2010, the concentrator consistently exceeded the target of 4400tph while processing harder CuZn ores.

Jan 1, 2012

By Joseph Licavoli, Paul Sanders, Yang Yang

"Al-Sc-Zr alloys form thermally stable L12 precipitates which provide high temperature strength. Although the overall fraction of L12 Al3Sc and Al3Zr may be increased by increasing scandium (Sc) and zirconium (Zr) content, such additions may increase primary phase fractions and do not produce desirable secondary phase morphologies. Rapid solidification techniques, such as melt spinning, increase solute atom concentration within the matrix. When the supersaturated matrix is aged, higher precipitate volume fractions at low Sc and Zr levels can be achieved improving high temperature strength. Melt spinning was used to rapidly solidify (107 k/s) a thin ribbon of Al-0.5Sc-0.4Zr at. %. The ribbon was compacted and extruded into 99.8% dense rods, and then aged using multi-step isochronal heat treatment up to 600°C. Precipitation strengthening was evaluated by ambient hardness measurement. The ambient hardness of melt-spun ribbon after precipitation hardening increased by 450 MPa (~67% increment) during isochronal heat treatment.INTRODUCTION Small Sc and Zr additions to aluminum improve strength and creep resistance above 300°C due to tri-aluminide precipitation of Al3(Sc,Zr) in L12 structures similar to ??, Ni3(Al,Ti) in nickel superalloy, but the Al3(Sc,Zr) particles have a Sc-rich core surrounded by Zr-rich shell (Figure 1). The Al3Zr shell limits atomic transport between the Al3Sc core and the matrix and reduces coherency strain. These factors reduce precipitate coarsening rate at elevated temperature (Bergner & Van Chi, 1977; Fujikawa, 1997; Knipling et al., 2011; Clouet et al., 2006).Figure 1. Simplified schematic model of precipitate Al(Sc,Zr) in Al-Sc-Zr alloy. Shell is rich of Al(Zr) intermetallic phase, particle core is rich of Al(Sc) intermetallic phase (after Voorhees, 2006). Numerous Al3(Sc,Zr) particles increase alloy strength and creep resistance as the precipitates impede dislocation glide and to a lesser extent climb. Previous work on ternary Al-Sc-Zr alloys show large strength increases versus binary Al-Sc, and Al-Zr alloys in Table 1."

Jan 1, 2018

By Frederick J. Browne

Water, water everywhere, but not a drop (fit) to drink! Trite, but how often only too true? What is there met with in mining which, under various circumstances, may be said to be the most sought-for and highly-prized and also the most objectionable and most feared? Water! What visions that combination of five letters brings to all thoughtful minds? Up to near the end of the eighteenth century water was thought lo be an element but was then discovered to be the result of the combustion of two volumes of hydrogen with one volume of oxygen, and water so produced is chemically pure. Pure water is a clear and colourless liquid when seen under ordinary conditions, but appears bluish when seen through a long tube, and this same bluish tint may be observed in many lakes, especially those of glacial origin. A story often told describes a prospector in the desert who, failing to find water to replenish his canteen, suffers torture and death under fearful circumstances. Then again we may recall the flooding of mines, where water poured in so quickly that there was no opportunity of saving the unfortunate workmen. Instances might be multiplied without number showing that either the lack or excess of this essential fluid has taken heavy toll of human life. In all branches of mining and associated industries water must be dealt with to a larger extent, from an economic point of view, than any other substance, and very often the purity of the water is a matter of considerable importance.

Jan 1, 1925

By K. van Netten, T. P. Ernst

"Froth flotation has been used successfully for about a century in the beneficiation of both coal and mineral particles. With the on-going trend towards lower feed grades, however, there is a need to transform this technology in ways that can deliver ultrafast separations, with strong selectivity, and recovery, covering a broader size range. It should be recognised that the hydrophobic effect, with its highly selective and long-range interactions, will most likely underpin any new technology. We identified the separation of the concentrate from the tailings as the rate determining step of conventional flotation technology. This limitation was then addressed by developing a novel flotation technology, insuring the formation of a concentrate that could be separated more rapidly from the tailings. We introduced a novel binder medium, a highly concentrated water in oil emulsion, to act as the focal point for hydrophobic adhesion, effectively replacing the air bubbles used in conventional flotation. The hydrophobic particles adhere to and become embedded within the binder, forming saturated agglomerates that float upwards. Moreover, by forming these large and resilient agglomerates, the product can be quickly dewatered over a screen and separated almost immediately from the tailings. Remarkably, this new binder permits residence times in the order of a few seconds under batch conditions. This paper examines the performance of the technology as a function of the oil wt% added to the slurry. The paper also examines the performance of the technology as a function of the particle size, showing a decline as the particle size exceeds 0.50 mm.INTRODUCTIONFroth flotation involves the collision and adhesion of hydrophobic particles to rising air bubbles, the carrying of those particles from the bubbly-pulp zone into a froth zone, and subsequent drainage and migration of the pulp to achieve the final concentrate (Wills, 2006). Within a Jameson Cell the feed slurry and air bubbles are brought into intense contact within the active area of the downcomer, achieving rapid kinetics of hydrophobic particle adhesion to the air bubbles (Harbort et al., 1994). However, once the bubble laden product and tailings emerge from the downcomer there is the need for separation of the concentrate from the tailings, an inherently slower process. In other devices such as mechanical cells the initial kinetics of particle adhesion are far slower, relying on the turbulent eddies throughout the cell, while in a column the kinetics rely upon an even slower process of bubble interception with suspended and settling particles (Gorain, 2007). However, in all cases the driving force for segregating the bubbles from the tailings, and the drainage of the froth are inherently the same. We do note, however, recent advances by Galvin and co-workers in achieving so-called Fast Flotation, utilizing a system of inclined channels to dramatically increase the segregation rate of bubbles from the tailings, permitting much higher gas and feed fluxes to be applied, achieving up to a ten-fold throughput advantage (Dickinson et al., 2014). Any further improvement within the existing flotation paradigm would require the introduction of centrifugal forces, but this would also require the formation of much finer bubbles than is typically used given the tendency of relatively large bubbles to reach a limiting slip velocity due to deformations and increased drag. Across all flotation devices we argue the rate determining step remains the segregation of the bubbles from the tailings."

Jan 1, 2016

By David Penswick

Despite anecdotal evidence to the contrary, the mining industry is not in decline. Rather, the world?s largest mining companies are among the most consistently profitable companies in any industry. In many cases, profitable mining companies have been built around a few large scale, long life mines. These criteria for success ? size and long life ? have led to the current preference for deposits that can be exploited using open pit methods. However, developments in the science of block caving have resulted in this mining method achieving costs and productivities that are competitive with the largest open pits, while achieving widespread applicability. One implication of the low costs and widespread applicability of block caving is that some current open pits are possibly too deep.

May 1, 2003

By G. S. Hume

Research thrives on ideas, and the theoretical considerations of today are either the discarded notions or the proven facts of tomorrow. The progress made in the past fifty years in the acquisition of knowledge of petroleum geology is no less astounding than is the tremendous increase in the production of oil on the North American continent from 61 million barrels in 1897 to 1,917 million barrels in 1947, an increase of 3,300 per cent, with production of natural gas expanding from less than 400,000 Mcf in 1897 to approximately 4,500,000,000 Mcf, or an increase of 11,000 fold in the same period. In the search for and discovery of the oil and gas fields that have yielded such prolific wealth, no idea has had a more profound effect than has the ?anticlinal? theory of oil accumulation, propounded in 1844 by Sir William Logan, the founder of the Geological Survey of Canada, after noting the position of oil seepages on the crests of anticlines in Gaspe peninsula. Sir William apparently was not much impressed with his own idea at this time, but after the Drake well discovery in 1859 and the publication by Henry D. Rogers, of Glasgow University, formerly of the Pennsylvania Geological Survey, of a paper in which he pointed out that the seepages in Pennsylvania were on anticlines, T. Sterry Hunt, an associate of Sir William Logan on the Geological Survey of Canada, published a reasonably comprehensive statement of the anticlina theory in the Montreal Gazette on March 1st, 1861. Hunt recognized the fact that the oil ?being lighter than the water which everywhere penetrates the rocks below the water level, naturally rises and accumulates along the crown of these anticlines". This was a recognition of the fact that gas, oil, and water in an anticlinal structure separate according to buoyancy or specific gravity. For some years the anticlinal theory does not seem to have attracted much attention, but when I. C. White in 1883 revived it and put it to practical use by prospecting for 'anticlinal' oil an gas structures in Pennsylvania, West Virginia, and Kentucky, its real value not as a theory but as a fact became widely recognized. Even today, the search for anticlines as oil and gas structures is being vigorously continued. In the past fifty years, however, it has become widely recognized that petroleum and natural gas collect in many different types of structures, and these have become known by the general name of 'traps'. About 1890, terrace structures were highly regarded because it was thought certain oil fields in Pennsylvania, New York, and Ohio were directly related to them. However, as Wilson (2, p. 437) has pointed out, it is recognized to day that ?'wherever the surface evidence is complete and dependable, other factors (than the terrace structure) are found to be in control'.

Jan 1, 1948

By H. Feldheiser

Acid resistant brick linings are state of the art for anti-corrosion linings in tanks for high pressure acid leaching (HPAL) treatment. The design of these brick linings has to take into account the almost non-elastic behaviour of the brick lining inside a relatively highly elastic steel vessel. There must be tools and data available to determine for the steel vessels the thermal growth plus the pressure expansion and for the brick lining the linear thermal expansion and the chemical swell. Thermal shocks and pressure drops are not regular operating events but their negative influence on the lifetime of a brick lining has to be a part of the engineering study. Finite Element (FE) models as well as a lot of research and development on brick lining materials is the only way to find a path through the complex engineering work for pressure vessels.

Jan 1, 2004

By C. Villaseca, F. Penna, R. Villarroel

Acid mist is the undesired result of copper electro-winning (EW) process, generating a contaminated and hazardous environment in the working areas, as well as promoting high corrosion conditions for structures and equipment in the EW tank-house due to the buoyancy of sulfuric acid in aerosol form. Likewise, organic entrainments that occasionally occur in this process contaminate the cathodes, as well as increasing the risk of fire. LateralVex® and LateralFlow® are technologies that effectively and efficiently solve these problems, without affecting the usual activities of the operators, thus presenting a significant distinction with respect to other technologies that seek to solve these problems. Minera Antucoya, an AMSA group company, which produces 80,000 tons of electrolytic Cu per year, decided to install both technologies for its EW tank-house, LateralVex® in commercial cells and LateralFlow® in scavenger cells to keep both the acid mist and the organic entrainments under control. This paper presents the effects of applying these technologies in Minera Antucoya’s electro-winning plant, the challenges addressed, the difficulties encountered, the problems and opportunities that their implementation involved, as well as the surprising results obtained at the time of measuring the acid mist— less than one hundred’s part of the Allowed Weighted Limit—in samples taken with the plant operating at maximum current capacity. Additionally, the paper includes some of the improvements identified during the period, more than 3 years, in which these technologies have been in operation in Minera Antucoya. INTRODUCTION Electrowinning is the most used electro-chemical process in the hydrometallurgical industry for the recovery of highly pure metallic copper as its final product, which is formed in previous stages in an aqueous medium that goes through a selective process using organic solvents to separate impurities and concentrate the metal in a sulfuric acid solution. In the last stage, this solution goes through a process in which high- density current at a low voltage is applied, so that the metal in the solution will deposit in solid state on a plate, usually a stainless-steel plate. This last process involves the generation of other sub-products due to the electro-chemical dissociation of the electrolyte’s components, or to the addition of chemical additives, or due to specific physical conditions or lack of controls during the operation.

Jan 1, 2019

By Y. Rama Murthy, Amit Ranjan, Pankaj Satija, Sunil K. Tripathy

"Chromite ore is one of the essential raw materials for ferroalloy and steel industry. Boula-Nuasahi belt of Sukinda region, Odisha, is the only resource of chrome ore in India. The Indian deposits are typically characterized as ferruginous and siliceous type ores. Chrome ore is generally mined by open cast mechanized mining method in these areas. The run-off-mine (ROM) ore from the various mines is sent to beneficiation plant via stack yard for further up gradation. The chrome ore beneficiation plant (COB) has two major circuits: comminution (feed preparation) circuit and beneficiation circuit. In the comminution circuit, the ore is reduced to <1 mm size ( for complete liberation of chromite) from -220 mm size in stage wise crushing (primary and secondary crusher) followed by screening and single stage grinding in a ball mill. Fraction having size <1 mm is further upgraded in the beneficiation circuit to produce three different concentrates having specific chemical composition and Cr: Fe ratio. The beneficiation plant is a complex circuit comprising of combination of unit operations (spiral concentrator, Floatex density separator, hydrocyclone, wet shaking tables). In the recent years the overall performance efficiency (grade and recovery) of the beneficiation circuit got affected with numerous changes in the run-off-mine ore quality (physical and chemical), mineralogical composition, etc.In this article, attempts made for improving the performance of chrome ore beneficiation circuit is discussed. The approach adopted and practical problems encountered while the process were also highlighted. The results of the trials has shown an improvement in the performance of the cyclone (d50 : 56 µm – 40 µm) and chromite losses into tailing to <12%.INTRODUCTIONChromite has a wide range of application, from refractories to metallurgical industries, and from chemical to non-ferrous alloy industries. Chromium ore (Fe2+, Mg) [Cr, Al, Fe3+]2O4) occurs exclusively in rocks formed by the intrusion and solidification of molten lava or magma which is very rich in the heavy, iron containing minerals such as pyroxene and olivine. With the richness of silica and iron, the chrome ores are broadly classified as siliceous type and ferruginous type. Pure chromite with composition FeCr2O4 is rare because magnesium usually substitutes for ferrous ion and aluminum and ferrous ion substitutes for chromium. Generally the associated gangue minerals are talc, quartz, hematite, goethite, limonite, gabro, serpentine, anorthosite, dunite, pyroxinite, etc. Around 96% of the chromite ore production is consumed for metallurgical applications of which 94% is converted into different grades of ferrochrome i.e., high carbon ferrochrome and charge chrome as shown in Figure 1. Stainless steel being the leading consumer of ferrochrome, any change in the dynamics of the stainless steel industry impacts overall chrome ore demands significantly."

Jan 1, 2016