Search Documents

By L. Vinnett, T. Ledezma, F. Contreras, F. Díaz

"Mass balances in secondary grinding are subject to critical constraints mainly because of the unknown load distribution from the SAG mills, the uncertainties in the hydrocyclone split estimations and the lack of flowmeters in the key streams. In this paper, a methodology to support mass balances based on the use of radioactive tracer is presented. This approach was successfully implemented in two secondary grinding circuits of Minera Los Pelambres, which operate with ball mills of 21’ x 33.5’. The method allowed the load distribution of the SAG product (secondary grinding feed) to be determined. This load distribution was used as an input in the mass balance data reconciliation.The effective residence times of solid tracers were obtained in the secondary grinding equipment, where irradiated solid was used as a tracer. The residence times were obtained from the parametric deconvolution between the input and output tracer signals. The model fitting was performed to reconstruct the normalized output tracer concentration. Effective residence times of solid tracers in the ball mills ranged from 1.9 min to 9.5 min. The use of radioactive tracer measurement in grinding circuits is a powerful tool to consolidate mass balance results as well as to characterize grinding mills.INTRODUCTIONGrinding is the last stage of the comminution circuits. At this stage, the ore particles are reduced in size by a combination of impact and abrasion, either dry or wet (Austin & Concha, 1994). The grinding equipment mostly used in industrial operations correspond to horizontal tumbling mills (Wills & Napier- Munn, 2006). Tumbling mills employ steel balls or rods as grinding media. Ball mills, which are a type of tumbling mills, use steel grinding media with greater surface area per mass unit than SAG (semiautogenous grinding) mills or rod mills (primary grinding). Hence, the ball mills are suitable to obtain the particle size required in the next separation stages (Napier-Munn et al., 1996; Wills & Napier-Munn, 2006)."

Jan 1, 2016

By J. P. Piguet, A. Hosni, J. P. Josien, H. Baroudi, R. Hadadou

"The iron ore mines in the Lorraine region of north-eastern France cover a surface area of approximately 3,900 km2 and involve more than 150 cities. A total extraction method was usually used during exploitation, but this technique was sometimes replaced by the room and abandoned pillar technique when it was necessary to protect surface buildings and infrastructure. Rooms and abandoned pillars were initially designed to ensure long-term mine stability. However, this aim was not always reached and numerous collapses occurred in the Lorraine iron basin, either during production or several years after closure. Several subsidence events were identified during a period of one century; the most recent event occurred in 2012. Two groups of events were identified. The first group represents events characterized by sudden surface movement, and the second group includes event characterized by progressive subsidence.Numerous studies conducted during the last decade helped improve our understanding the origin mechanism of spontaneous or progressive (slow) events. These studies led to identifying long-term potentially unstable underground zones (hazard zones), particularly deep zones located under buildings and infrastructure. The latest are currently monitored by microseismic networks. A similar high requirement level is needed for unstable zones without taking into account the kinetics of the subsidence, which is very important for safety. Thus, GEODERIS initiated this study, primarily to acquire a better understanding of the kinetics of the progressive events group and identify the main parameters that could explain why some pillars zones developed a maximum amplitude subsidence on surface within a few hours or days, while it took several weeks to months for others. In practice, the results of this study will facilitate adapting the requirement level of microseismic monitoring system to the kinetics of pillar collapse.To retrieve the real kinetics for each event, historical and sparse documentation was used. Firstly, archives research was conducted, especially testimonies and newspaper articles published during the events. This work helped to gather useful information that sometimes contained a precise description of subsidence duration. The archives research helped to classify some progressive events according to the subsidence kinetics. Secondly, a diagnostic of geotechnical and geomechanical parameters of historic events was realized, combined with a cross analysis of the data. The analysis took into account dimensions of underground workings (e.g., pillar lengths, widths, heights, introduction of a “pillar shape factor”, and stress amount). An original expression was highlighted to connect the pillar geometry to the stress state. The kinetics expression was calibrated to classify the historic events taken into account according to the kinetics of movements. The kinetic criterion was applied to predict subsidence kinetics for the potential unstable zones currently monitored by a microseismic system."

Jan 1, 2015

By W. E. Cockfield

THE object of this paper is to review recent geological work in the Cariboo district and to present notes on the recent development of mineral properties. The Geological Survey has done considerable work in the Cariboo district, extending over a period of years. In 1885 and 1886, Bowman (1) mapped the geology of a large area. In 1922 and 1923, Johnston and Uglow (2) mapped Barkerville area in some detail and prepared a report on the placer and lode gold deposits. In 1931 and 1932, Cockfield and Walker (3) mapped the Quesnel Forks area. In 1933, Hanson reported on Willow River area ( 4), and in 1934 made a detailed examination of part of the Barkerville area (5). In 1935, Lang commenced work on the Keithley area, lying to the southeast of the Barkerville area, and in 1936 published a preliminary re-port (6). The work on Keithley area was continued in 1936 by both authors of the present paper. As the results of the earlier work have been published, this paper will be concerned largely with Keithley area, that is, the part of the region lyinp between longitudes 121° 00' and 121° 30', and latitudes 52° 45' and 53° 00 . This area lies astride Cariboo (Swamp) river and extends north some 17 miles from Keithley, which is situated near the southern border of the map-area (see sketch-map). Points in the western part of the map-area are fairly accessible. A road extends from Barkerville to upper Cunningham creek, and from this a trail crosses Snowshoe plateau to Keithley. A second trail from this road leads to the lower falls on Cariboo river. From this road, a branch road leads to upper Antler creek, with a trail leading from this branch road to Keithley. Part of this western half of the area is made up of the Snowshoe plateau, which constitutes a gently rolling surface, at or above timber line, where trails are largely unnecessary.

Jan 1, 1937

By K. Ebrahimi-Nasrabadi

The dependence between the extent of conversion of cryptocrystalline magnesite to caustic magnesia was studied experimentally in the temperature range of 400?1200 °C and for calcination times up to 8 h. A TGA?DTA analysis showed that decomposition begins at temperatures as low as 340 °C and is completed at 600 °C. Measurements of specific surface area (SSA), iodine adsorption number (IN), crystallite size, and loss on ignition were carried out to characterize the product quality. It was found that while all the parameters are dependent on the extent of calcination, densification of the product caused by grain coarsening affects their final values. As a consequence, SSA and IN went through a maximum with time. The study showed that high quality caustic calcined magnesia can be produced in a narrow range of temperature (600?650 °C) and time (1?4 h). Medium quality caustic calcined magnesia can be made within a wider range of parameters.

Aug 1, 2013

By Limao Zhang

This paper presents a BIM-based Risk Identification Expert System (B-RIES) for metro construction, composed of three main built-in subsystems: BIM extraction, knowledge base management, and risk identification subsystems. The engineering parameter information related to risk factors is extracted from the BIM of a specific project where the IFC standard plays a bridge role between the BIM data and metro construction safety risks. An integrated knowledge base, consisting of fact base, rule base and case base, is established to systematize the fragmented explicit and tacit knowledge. A hybrid inference approach, with case-based reasoning and rule-based reasoning included, is developed to improve the flexibility and comprehensiveness of the system reasoning capacity. During the safety risk identification process, B-RIES is able to improve the inefficiencies in engineering information extraction, reduce the dependence on domain experts, and facilitate knowledge sharing and communication among dispersed clients and domain experts. A typical safety hazard identification in the Mingdu station, located in the Wuhan Metro Line Two, is presented in a case study. The results demonstrate the feasibility of B-RIES, and its application potential. B-RIES can be used as a decision support tool to provide guidelines for safety management in metro construction, and thus increase the likelihood of a successful project in a complex environment.

Aug 1, 2013

By S Sokhanvaran

Electrodeposition of silicon from a cryolite based electrolyte at a relatively low temperature (1000°C) is a promising approach to generate high purity silicon. In order to obtain fundamental data pertaining to electrowinning of silicon from Cryolite?SiO2 melts, density and electrical conductivity measurements were made. A range of temperatures and SiO2 contents was studied for each property. It was found that while density has an inverse relationship with temperature, the dependence for electrical conductivity is direct. Increasing silica content up to the saturation limit (~ 5 wt%) increases the density whereas further increase in SiO2, lowers the melt density. On the other hand, the conductivity is lower for the melts with greater SiO2 content, at any temperature.

Jan 1, 2011

By C. D. M. Chisholm

IN discussing stope filling, or backfilling, at the Sullivan mine, at Kimberley, B.C., a brief description of the problem will first be presented. The Sullivan orebody is a replacement in quartzite, with the ore con-forming, for the most part, with the bedding. The dip of the vein, apart from local irregularities, averages about 15 degrees near the outcrop in the southwest section of the mine, and steepens to almost 40 degrees at the northeast end of the mine. The thickness varies from a few feet to over 200 feet at the widest sections. The mineable length along the strike has averaged about 4,000 feet between the 4,600 and 3,900 levels-the section under discussion in this paper. To date, 28,000,000 tons of ore have been mined by the room-and-pillar method. Prior to 1930, all ground opened up had been supported by ore pillars, left during mining operations. From that time, the recovery of the ore from these pillars has been given serious consideration. Backfilling, as being carried on today, is the result of this study and is being done for two reasons: (1) to allow extraction of the ore pillars, and (2) to minimize subsidence of the hanging-wall rock, except where forced caving is found desirable. PRELIMINARY DEVELOPMENTS LEADING TO BACKFILLING When the Sullivan orebody was first opened up, early in the century, there appeared to be low-grade sections of the vein sufficient in extent to serve as permanent support for the roof. However, as mining extended into sections of the vein that showed continuous ore over greater areas, wooden cribs, filled with waste and low-grade ore, were erected. In some stopes, these cribs were as large as 40 ft. by 100 ft. in plan and from 50 ft. to 60 ft. in height, but it was soon realized that this method of support was inadequate. As mining progressed, it was found necessary to leave ore pillars, which eventually became the sole system of support. At first, these pillars were left at irregular intervals, but later they were laid out at definite locations on the mine plans, and these locations were adhered to as closely as mining would permit.

Jan 1, 1941

By J. I. Carroll, J. A. Walker

"Abstract - Camelback is a small (=200 000 tonnes), moderate grade (5%-7% Zn+Pb), volcanogenic massive sulfide deposit, which occurs within the Nepisiguit Falls Formation of the Ordovician Tetagouche Group. The host rocks are tuffaceous sedimentary rocks (Little Falls member) that overlie quartz-feldspar porphyritic tufflavas (Grand Falls member). The hanging-wall sequence comprises rhyolite of the Flat Landing Brook Formation, overlain by the Forty Mile Brook tholeiitic basalt. A dike of unaltered andesite was intersected beneath the massive sulfides, but was not found in the hanging-wall sequence in the vicinity of the deposit. The stratiform part of the deposit is made up of two, steeply south dipping, subparallel massive lenses that average approximately 4 m in thickness. Each lens is zoned, with an upper part consisting mainly of a pyrite and a basal part containing pyrite, sphalerite, and galena, with Ag values. The Au content in the massive sulfides is low (average = 52 ppb for 271 samples), but tends to be enriched in the massive pyrite near the top of each lens. Oxide facies iron formation is spatially associated with the massive sulfides, and has been traced up to 1800 m along strike. Footwall hydrothermal alteration is typical of VMS systems, and is characterized by depletion in K2O and Na2O, and enrichment in MgO and Fe2O3T with proximity to massive sulfides. The massive lenses are underlain by intensely chloritic, fine-grained, tuffaceous sedimentary rocks containing locally significant sulfide (chalcopyrite > pyrite > pyrrhotite) veins, which are interpreted to represent feeder zone mineralization. Unlike many VMS deposits, there is no evidence of silicification beneath the massive sulfides at the top of the feeder zone. The oxygen isotopic compositions (d18O = -1.5‰ to -0.3‰) of hydrothermal chlorite coupled with sulfur isotopic compositions (d34S ˜ 12‰) of the massive sulfides suggest that seawater was the dominant fluid in the hydrothermal system. Normalized rare earth element diagrams show flat Ce profiles and positive Eu anomalies, indicating that modified seawater was involved in ore formation; i.e., high-temperature (=350ºC), acidic, and reduced prior to entrainment into the hydrothermal cell. Although, seawater was the dominant fluid in the sulfide-forming system, d34S values of stringer zone sulfides (8.5‰) coupled with elevated Sn (400 ppm) in one massive sulfide sample indicate that there was at least some magmatic component in the hydrothermal cell."

Jan 1, 2006

By Masahiro Eguchi, Giuseppe Granata, Chiharu Tokoro, Hiroki Fukuda, Yuichiro Toba, Shungo Hobo

"Currently, large amounts of wastewater containing boron are discharged from industries like coal-fired power plants. Although coagulation-sedimentation is widely employed for their treatment, only a little consideration has been given to its mechanism. An additional problem is that the produced sludge has poor solid-liquid separation. This study is focusing on coagulation-sedimentation using magnesium, examining the mechanism and improving the solid-liquid separation. First, the co-precipitation with magnesium hydroxide was conducted against high-concentration boron wastewater with 500 mg/dm3as B. Second, in order to improve the solid-liquid separation by maintaining high reactivity, low-crystalline magnesium oxide was synthesized from magnesium carbonate by calcination at 400–700°C. It was tested as an adsorbent of boron and compared to co-precipitation with magnesium hydroxide. Co-precipitation showed high removal capacity. X-ray diffraction (XRD) of the sludge revealed the presence of other compounds besides magnesium hydroxide. This result suggests that other processes play a role other than simple adsorption on to magnesium hydroxide, and provides a plausible explanation for the observed high separability. As for the adsorption, the synthesized magnesium oxide immobilized as much or more amount of boron than co-precipitation. Furthermore, the results of fourier transform infrared spectroscopy (FT-IR) suggested the residual magnesium carbonate improved solid-liquid separability due to its poor solubility.INTRODUCTIONBoron is used in various industrial applications. In glass industry, the addition of a little amount of boron into glass products can enhance heat-resistance and chemical-resistance. Semi-conductor industry also employs boron as dopant for silicon. From these industries, large amounts of wastewater containing boron have been discharged. Additionally, coal-fired power plants have been recently discharging highly concentrated boron wastewater because the amount of boron contained in coal has been increasing due to a gradual decrease of the quality of coal. Since boron is partially proved to be toxic for animals, plants, and human beings (WHO, 1998),the guideline of the World Health Organization limit the boron concentration in drinking water to 2.4 mg/dm3(WHO, 2009).Because boron does not precipitate from solutions by simply changing the pH, the removal could be carried by operations such as adsorption or ion exchange. However, since ion exchange is an expensive operation with relatively low capacity, it is not suitable to treat the large amounts of wastewater produced by heavy industries like the coal-fired power plants. Therefore, coagulation-sedimentation method is still widely used as a suitable alternative way."

Jan 1, 2017

By A. L. Mular

"On behalf of Bob Bruce and myself I would like to begin by stressing some key points.First, most of us know that the Canadian Mineral Processors was formed in 1969 and is an offshoot of the Canadian Gold Metallurgists. I attended that first meeting in 1969, and I haven't missed a meeting since! Pretty obvious that CMP serves the best booze! At any rate, we know that our meetings are supported by CANMET. Camsell Hall is always at our disposal; Bob Bruce acts as permanent secretary pretty much free of charge; we receive a financial grant from CANMET. This brings me to a second point.Second the Canadian Mineral Processors do not enjoy a free ride in this relationship. CMP provides a genuine service to the mining industry, to government, and to universities. For the industry, CMP serves as a forum for the rapid dissemination of new ideas and new technology developed at remote locations throughout Canada. New developments outside Canada are introduced by invited speakers at our meetings. The effect is to help reduce operating costs and increase efficiency.For government, problem areas and research priorities can be isolated through mutual discussions. Direct communication at our meetings can help CANMET to temper its goals and modify its national priorities.For universities, CMP provides a wealth of operating experience and practical know how. The yearly proceedings are a major current reference source fo1· those of us who teach mineral processing. Admittedly, the proceedings are publ-shed from CMP coffers. However, I note that our fees are up this year, which brings me to a third point.Third, we face some potential problems of a financial and political nature. From a financial view, we may lose our CANMET grant and other financial good will simply because of spending constraints. Our fees are expected to climb each year thereafter.From a political view, we know that the metallurgical society of CIM is anxious to incorporate CMP as a section. The pros and cons of such a merger have been described in a recent mailing. In th2 final analysis, the political and financial problems are interrelated. There are several alternative solutions to both problems, which brings me to a fourth point"

Jan 1, 1979

By G. Ozbayoglu, Z. Ozdemir

Turkey is the main boron minerals producing country in the world. The most important boron minerals are tincal, colemanite and ulexite. All mining, beneficiation and handling operations generate fines which cause ecological and economical problems. Utilization of this accumulated material requires both upgrading and agglomeration. The aim of this research was to exploit the ulexite fines by improving their grade and size. Attrition-scrubbing followed by washing and screening was employed for upgrading the fines. It was found that the grade can be increased from 23-25% B2O3 to 29% B2O3 with 73% recovery. Briquetting was applied as the size enlargement process. During the briquetting, the effect of moisture content, pressure, amount and type of binder, and drying on the quality of briquettes were investigated. The tests showed the possibility of production of strong briquettes by adding water alone, but the briquettes had no resistance to abrasion and water. Binders, namely boric acid and borax have been added to improve the properties of briquettes. The results showed that the compressive strengths and abrasive resistances of briquettes obtained with both binders were acceptable. However, the briquettes have no water resistance properties.

Jan 1, 2004

By B. Stettner, J. Asante, S. Abraham

The levels of nitrogen in steel produced in various metallurgical vessels vary significantly. For example, the tap nitrogen levels in steel produced in the BOF are around 4Oppm, as compared to 70-100ppm in both DC and AC electric arc furnaces. Given the pressing need to reduce nitrogen levels in steel to satisfy customer demand, IPSCO Inc. has gained considerable experience in controlling nitrogen levels in steel over the course of the last three years. Hence, a cost effective process has been developed through an intensive nitrogen control program from steel melting in the EAF through to the continuous slab casting stage. This paper describes the practices employed at each stage of the steelmaking process that have enabled IPSCO Inc. to reduce and control nitrogen levels in steel.

Jan 1, 2004

By A. Blackmore, D. Baker, L. Human

"Mechanical mixing equipment is common in a wide variety of mining, metals and process applications, such as hydrometallurgical reactors, solvent extraction, digestors, and tanks for storage of slurry or hydrocarbons. Computational Fluid Dynamics (CFD) has been applied successfully to single-phase mechanical mixing problems for several decades and is established as a reliable design tool. As computational power and CFD codes have improved over the years, there have been significant advances in modelling capabilities including improved models of turbulence, interaction of rotating and stationary components, multiphase flows, and modelling of free surface interfaces, for example. This paper will provide an overview of the application of CFD to mechanical mixing problems. First, it will review the traditional single phase Multiple Reference Frame (MRF) approach and introduce a range of advanced modelling techniques. Three examples of the application of CFD to industrial mixing problems will be given. It will be demonstrated that CFD is an effective tool for reducing technical risk in design, for identifying the root-cause of mixing problems, and testing modifications to existing operations."

Jan 1, 2015

By G. Bartolacci

In a COREM-McGill collaborative research and development project, gas dispersion parameters and froth properties were manipulated in a copper flotation plant to study interactions between the collection and the cleaning zones. In this paper, specific work on developing some relationships between operating conditions and froth stability in several different types of flotation cells is reported. Froth stability, measured by image analysis, was related to the following process conditions for specific flotation machines in an industrial case study: Gas flow rate, collector dosage, pH, frother type and dosage. Across the range examined, froth stability was improved through an increase in gas flow rate and/or frother dosage. Metallurgical results (grade and recovery) showed that both gold and copper were dependent on froth stability. Results indicated that flotation conditions could be optimized by monitoring froth stability.

Jan 1, 2007

By Jaeheon Lee, Junmo Ahn, Doyun Shin

"Many alternative leaching systems including bacterial leaching have been introduced to avoid passivation on the surface of chalcopyrite and to increase the leaching efficiency of copper from chalcopyrite. Recently, glycine, one of the simplest amino acids, has been emerging as an efficient and environmental-friendly lixiviant to recover copper. In the present study, an alkaline glycine–peroxide lixiviant system was used to leach copper from chalcopyrite concentrate and the leaching mechanisms were also investigated by a suite of kinetic studies under different conditions. The chalcopyrite concentrate contains 28.8% copper with 30.8% sulfide sulfur. The effect of concentration of glycine and hydrogen peroxide of the leaching solution was investigated. Glycine concentration was varied from 0.5 to 1.0 M and the hydrogen peroxide concentration was changed between 3 to 5%. Leaching time and pulp density were also varied. Hydrogen peroxide is an oxidant of the system and the leaching efficiency with periodic additions of the peroxide was also studied. A mineralogical study was performed using XRD and SEM. To investigate the surface of the residue materials, XPS was used to see if any passivating layer was formed during the leaching. Detailed results from mineralogical, chemical, and metallurgical studies will be presented and discussed.INTRODUCTION The greatest global resource of copper is low-grade chalcopyrite and heap bioleaching may be the only economic option for its processing. However, formation of a passivating layer on the surface of chalcopyrite slows down the oxidation reaction and reduces the efficiency of the process."

Jan 1, 2017

By Z. Z. Öztürk, N. Sarica, A. H. Üçisik, C. Bindal

"Titanium oxide films were fabricated on commercially pure titanium surfaces via anodization procedure. Anodization parameters, anodization time and voltage were altered, whereas temperature and chemical composition of anodization bath were kept constant. The main idea in this study is to obtain rough titanium-oxide surfaces. The type and feature of titanium oxide formed were observed via SEM and EDX analyses. What was revealed from SEM and EDX analyses were combined with Ti-O phase diagram in order to make judgment on the type of phases obtained, e.g. solid solution and/or compounds. Studies on the different regions of each sample showed that surfaces consist of different titanium oxide compounds with various O/Ti ratios in nano level and solid solutions varying in terms of chemistry on the same sample. Thus together rough surfaces and inhomogeneous distribution of "titanium oxides" were obtained. It was also found that when anodization time and voltage were increased, more granular surface with higher O/Ti atomic ratio was obtained."

Jan 1, 2015

By Michael Samis

Conventional project valuation techniques, such as discounted cash flow (DCF) method, are more frequently being criticised for the manner in which they consider the interacting effects of uncertainty and project structure (including management flexibility) on project value. Modern asset pricing (MAP; often called ?real options valuation? when applied to the analysis of flexibility) is a more general valuation framework that corrects many of the shortcomings of common valuation methods. Previous mining applications of MAP have tended to treat the ore deposit as a homogenous entity. While useful for demonstration purposes, this is inadequate for practical application in industry. This paper presents a MAP valuation example that allows for the heterogeneous nature of an ore deposit. It shows that deposit structure may increase the complexity of the mine planner?s decision so that results of a standard DCF analysis, or a simple MAP analysis that ignores the details of deposit structure, are misleading. In the example, a management is considering the development of an adjacent low-grade zone while mining operations in a high-grade zone are ongoing. If the low-grade zone is developed before high-grade reserves are exhausted, the proposed development will include both low-grade zone development and a capacity expansion to handle additional low-grade reserve production. If development of these reserves is delayed until the high-grade reserves are depleted, then the low-grade reserves can be developed without a capacity expansion. A typical DCF analysis would reduce the management?s decision problem to three alternatives: 1) continue mining only in the highgrade reserves, 2) immediately develop the low-grade reserves and expand capacity, and 3) delay low-grade zone development until the high-grade reserves are exhausted. The model presented here allows the management to reconsider the development and capacity expansion decision on a discrete half-year basis. It delineates price regions, for given levels of high-grade zone reserves, in which it is optimal to develop the low-grade zone, defer low-grade zone development and abandon the mine irrevocably. The model presented here extends the ability of mine planners to describe actual project structure while using the MAP valuation framework that is already noted for its capacity to combine project uncertainty and risk insights with a dynamic project description.

May 1, 2001

By G. K. Herzog

THE problems relating to the construction and use o{ mining equipment are basically the same as those pertaining to equipment in other industries. It is true that much mining equipment is subjected to an unusually severe combination of shock, high stresses, abrasive wear, and corrosive ? conditions, but in other industries, also, equipment must operate under similar adverse conditions, so that their experiences may readily be applied to the problems of the mining industry. Steel and iron are for obvious reasons the most suitable materials for the construction of the greater part of the equipment used in the mining industry. For a large percentage of uses, the ordinary plain carbon-steels and ordinary or unalloyed cast-iron are, and probably will continue to be for a long rime, entirely satisfactory materials. There are, however, many. conditions which cannot be satisfactorily taken care of by these materials, and alloy steels and irons must be used where the greatest possible economy is desired. In general, alloy steels and irons are used where it is necessary or economically desirable to use materials possessing properties superior to plain carbon-steel or ordinary cast-irons, such as: (a) better strength (b) better wear resistance (c) better corrosion resistance (d) better resistance to high temperatures (e) better resistance to low temperatures or combinations of two or more of these advantages. There are also conditions where materials having other special properties are required, such as, for example, certain magnetic or electrical properties for electrical machinery; but in the great majority of cases, one or more of the five advantages listed are the most desired.

Jan 1, 1938

By F. Parada, R. Parra

"The neutralization process of SO2 from coal burning plants is a well-defined technology using limestone to form CaSO4 according to the following reaction: CaCO3 + SO2(g) + 1/2O2(g) = CaSO4 This paper presents the results of a study carried out to validate the option of capturing SO2 using gases from a non-ferrous smelter; SO2 content was up to 12% using a three-stage fluidized bed reactor. The difference in SO2 content affects equilibrium conditions and kinetics, rendering a direct extrapolation of the high efficiency achieved for low SO2 content impossible. The R&D program consisted of a laboratory study using a semi-pilot operation of a one-stage fluidized bed reactor and the construction and operation of a three-step reactor prototype. Results show that the reaction proceeds according to the unreacted core model that imposes a compromise between CaCO3 conversion and SO2 capture. For high SO2 capture, the calcine from the reactor contained CaSO4 and CaO. A complete capture of SO2 from gases with 8 vol.% can be achieved with a mean reaction time of two hours at 800°C."

Jan 1, 2007

By T. Crivits

"Freeze lining technologies are used industrially to protect the integrity of furnace walls in pyrometallurgical reactors. This is achieved by solidifying a protective layer of slag on the inner furnace wall. In the current study, laboratory experiments have been undertaken to produce freeze linings in ‘Cu2232 O’-‘FeO’-MgO-SiO slags under controlled conditions using an air-cooled probe technique. Whilst most thermal models of freeze linings have assumed the freeze lining-bath interface to be at the liquidus temperature of the bulk bath and to be planar in geometry, the current research has demonstrated that this is not the case. Experiments undertaken using this high-temperature slag system have shown the interface at steady state conditions to be at subliquidus temperatures. The solid phases present at the interface do not include the primary phase and the interface is non-planar. The study indicates the need for improved understanding of the fundamentals of freeze lining formation, and of the influence of system properties and process parameters"

Jan 1, 2015