Search Documents

By Jin Liu, Torstein A. Utigard

At its Copper Cliff Smelter, Vale Inco Limited processes a bulk copper-nickel concentrate in two Inco oxygen flash furnaces. Coke supplies a minor proportion of the process heat requirements, limiting the flash furnace matte grade to the target 45% CuNiCo. Coke addition to the furnace offers a potential means of establishing a reducing barrier on the surface of the molten bath. Such a practice would be conducive to producing sulfur deficient (partially metallized) matte. At the same iron content, the iron activity of sulfur deficient matte is higher than that of regular matte. A supernatant coke barrier could, therefore, be expected to lead to higher nickel and cobalt recoveries, reduction or even elimination of magnetite furnace bottom build-up and increased sulfur elimination as SO2 in the flash furnace. Extensive experiments were conducted in a miniplant flash furnace to investigate the effect on process metallurgy of the suggested modified scheme. The introduction and description of the experimental set up were given in Part 1 of this paper and an early paper published in Yazawa symposium1 together with the results and some in depth discussion on metallurgy. This paper intends to discuss the kinetics of the miniplant flash furnace testwork.

Jan 1, 2015

By J. Gustavsson, S. Holmin, Å. Afvander, E. Rosseland, E. Zimmerman

There are numerous advantages in replacing lead-based anodes with mixed metal oxide (MMO) coated anodes in copper electrowinning; for example, lower energy consumption, improved working conditions for operators and less environmental impact. Since 2012, Permascand AB in Ljungaverk, Sweden has evaluated Permascand coated titanium anodes in copper electrowinning pilot trials at Glencore Nikkelverk in Kristiansand, Norway. The investigation has proceeded in three different steps (Phase I, II and III). In Phase I, different Permascand coatings, electrode structures and coating methods were investigated. The results showed that improved current distribution, lower energy consumption and longer service life could be obtained with expanded mesh electrode structure in a box configuration compared to rod anodes in a single-mode construction. In addition, improved current distribution and less coating wear was found when electrostatic spray coating was used instead of brush (manual) coating. It was also found that the extrapolated service life from controlled lab experiments at 200 A/m2 was much shorter compared to what was experimentally obtained in copper electrowinning pilot trials at similar current densities. This was mainly attributed to different coating failure mechanisms in lab and industrial copper production. INTRODUCTION Traditionally lead-based anodes have been used in copper in electrowinning due to lower cost. But there are many advantages in replacing lead-based anodes with mixed metal oxide (MMO) coated titanium anodes in copper electrowinning, such as lower energy consumption, higher corrosion resistance, improved working conditions for operators and less environmental impact. Still, many facilities are using lead-based anodes, although the progression of using metal oxide coated anodes in copper electrowinning has slightly increased (Robinson et al., 2012).

Jan 1, 2019

By R. J. Labine, D. I. Brisbin, R. Roussain, P. R. Coad

"Abstract - The Owl Creek Mine is located near the west end of the Neo-archean Abitibi greenstone belt, 17 km northeast of Timmins, Ontario, and 4 km north of the Destor Porcupine fault. Gold occurs in epigenetic quartz veins and their pyritic wallrocks in two zones within a package of east striking, steeply north dipping, volcanic and sedimentary rocks. At the West Zone, 1 729 603 t of ore with a grade of 4.83 g/t Au (268 587 troy oz.) were produced from an open pit centered on a wedgeshaped unit of Tisdale Group basalt that occurs between two overturned, south facing units of Porcupine Group graywacke and argillite. Basalt/graywacke contacts are locally marked by graphiticcarbonaceous argillite, strike-parallel faults and massive quartz veins.Deformed quartz+/-ankerite veins occur along the graphitic sedimentary/volcanic contacts and in gently to moderately dipping fractures in basalts, and, to a lesser extent, in graywackes. Veins also occur sub-parallel to steeply dipping 070° foliation. Altered host basalts are composed of iron carbonate, sericite, quartz, carbon, chlorite and disseminated pyrite. Gold occurs as inclusions in pyrite, and less commonly as free gold in fractures and along graphite-quartz grain boundaries in quartz veins. Fractures preferentially developed in more competent basalts during pre- to syn-ore deformation are interpreted to have provided the permeability required for emplacement of mineralized quartz veins. Carbonaceous basalt/graywacke contacts further enhanced gold deposition by acting as chemical traps. The interaction of hydrothermal fluids with these carbonaceous sedimentary rocks led to the characteristic local darkening of host basalts due to carbon impregnation and chlorite development."

Jan 1, 1998

By M. A. Power

The diamondiferous Drybones Bay kimberlite pipe is the largest pipe (900 m by 400 m) discovered to date in the Northwest Territories. The pipe intrudes granodiorite of the Archean age Defeat Pluton and contains crater, reworked crater (epiclastic) and diatreme facies kimberlite. In-situ measurements of seismic p-wave velocity were recorded with in-line refraction arrays over representative areas. Refractions from fresh kimberlite were recorded over epiclastic facies kimberlite in the eastern portion of the pipe and returned an average velocity of 4300 m/s. Refractions from weathered kimberlite were recorded on all lines and returned velocities ranging from 1900 m/s to 2200 m/s. Granite surrounding the pipe returned an average velocity of 5400 m/s. The results indicate that there is a definite contrast in seismic velocities between kimberlite and country rocks at Drybones Bay and suggest that seismic refraction surveys may be an effective means of screening kimberlite targets in glaciated areas underlain by igneous or metamorphic rocks.

Jan 1, 1998

By R. D. Corrans

"Abstract - Africa is endowed with a number of the world's giant ore deposits which have contributed significantly to the development of their host countries. Mineral exploration has a long history in the continent, but mining on an unprecedented scale took off during the latter part of the 19th century, accompanied by the development of lines of communication and other infrastructure to service the major mining centres .The ""Winds of Change"" which swept Africa in the 1950s and 1960s brought in new styles of government and economic management to a number of regions, often with demise of economic viability and infrastructure. ln recent years, with the end of the cold war, collapse of communism and changes in South Africa, new opportunities for mineral exploration are opening up rapidly in Africa. However, due to the large cost, long lead-in time, and high risk of developing new mineral ventures in the continent, it is necessary for the host countries to draft realistic and favorable mineral laws and fiscal codes in order to attract, and not deter, potential mineral investors.There will be an on-going role in mineral exploration throughout Africa for the artisanal miner, the smaller entrepreneurs and mining companies, exploration aid programs funded by the developed countries through African governments, as well as the major mining houses who have the resources to develop larger viable mineral deposits."

Jan 1, 1994

By M. G. Lipsett

One challenge in applying information technologies in Mining is building a business case. In Mine Maintenance, there is a complex flow of information that contributes to making informed business decisions. By understanding those information relationships and the cost of wrong decisions, analysts can estimate the value of information flow. Developers can then ensure that systems deliver key information in an accurate and timely way. In this paper, general maintenance decision-making is discussed, with examples of how model-based analysis can improve the information delivered to decision makers.

May 1, 2001

By D. Rylander

The operation of Quarry and Aggregate sites are similar to factory production, since it contains sequential production processes, tasks and activities to produce the output product. Compared to the plant though, the quarry processes are generally not synchronized and controlled towards the overall throughput of the site in real time. Some quarries control parts of the production but do generally not utilize real-time technologies for the whole site and all its activities. This fact indicates a general improvement potential in increased productivity at quarry sites, but also unsolved challenges for the same reason. The main contribution of this paper is the presentation of a Lean based method for how to describe the processes to identify control improvement potential within a site. The aim of the identified improvements is to increase overall site productivity by optimizing site, fleet and machine utilization towards the overall throughput, and minimizing operational expenses and inventories. Further the paper exemplifies the method?s usability with field studies at operational quarry plants successfully identifying and quantifying potential wastes and improvements. In addition the identified productivity improvements based on increased control and automation indicate challenges and needs in wireless communication and sensing technologies.

Aug 1, 2013

By Jerry Ran

Many large underground mines using the open stoping method have changed their primary applications of consolidated rock fill (CRF) to paste or consolidated hydraulic fill due to considerations of demand in infrastructure and equipment, system reliability, backfill capacity and material sources. However, some smaller or even large mines still use or consider using CRF for backfill purpose due to factors such as capital expenditure, availability or suitability of other fill types or in some cases local regulatory requirements. As demands on CRF applications diminish among major mining companies, there is a lack of recent literature on application of CRF to open stoping in design and operation. There are several methods being used for fill strength design. Results from these methods have been successfully applied to paste or hydraulic fill. However, the design strength for CRF is much higher than that determined by use of these widely accepted methods. In operation, CRF preparation and placement have significant impacts on the quality of placed CRF and therefore the mining performance. This paper reviews the current fill design methods and their applications to open stoping with presentation of the bench marking data, presents fill failure cases and various CRF preparation and placement arrangements and discusses quality assurance and control programs.

Jun 1, 2012

By Yves Caron

Résumédes travaux effectués De septembre 2009 àmai 2011 ? Plus de 21 000 m de forages complétés en avril 2011 et près de 9 000 échantillons ? 2,7 km de décapage, 52 tranchées et 852 m de rainures ? Estiméde ressources 28 mai 2010 (SGS Géostat) ? Essais métallurgiques en laboratoire (automne 2010) ? Étude économique préliminaire (janvier 2011)

May 1, 2011

By I. Filippova, L. Filippov

"The by-product potential of light rare-earth elements (LREE, La, Ce, Nd) and rare-metals (W, Nb, Sn) within the St Austell kaolin deposits (UK) is related to the kaolinisation process, which liberates the accessory heavy minerals of the host granite in the clay matrix and allows their separation in the waste streams. As a consequence these minerals are pre-concentrated in the micaceous residue which displays relatively high LREE content (around 170 ppm) hosted by monazite which is mainly distributed (up to 95%) in the -100 µm fraction. A combined gravity/flotation concentration flowsheet, starting with classification of the residue into 3 size fractions (+150 µm, 150-53 µm and -53µm) was developed. This study presents the results of the clay-rich -53 µm size fraction beneficiation by flotation using sodium oleate and hydroxamate as collectors.The effect of dispersant addition during de-sliming operations on flotation efficiency was also investigated. The LREE grade in the floated product obtained with sodium oleate increased from 3370 ppm to 5350 ppm and recovery from 30% to 80% with dispersant which is attributed to clay coating. Comparison of flotation performance and Falcon Ultra-Fine (UF) concentration of monazite to previous results obtained with Falcon Semi-Batch (SB) gravity concentrator on the unscreened raw residue clearly shows that flotation of the fine residue is more efficient than Falcon UF and Falcon SB. Indeed Falcon UF produced high recoveries (87-95%) but with almost no enrichment (1.3-1.4 ratios) whereas Falcon SB concentration of unscreened residue produced higher grades (up to 0.6 % LREE) but with low recoveries (17-22 %). These preliminary results show that LREE can be pre-concentrated suggesting that the micaceous residue stream (and the associated tailings dams) could be considered as a potential resource for these metals."

Jan 1, 2016

By S. J. Laskowski

In potash ore flotation, carried out in NaCI-KCI saturated brine (about 6-7 molar KC1 and NaCI solution), long-chain primary amines are used as flotation collectors. Long-chain primary amines are poorly soluble in water and their solubility further decreases at high electrolyte concentration. For ionic surfactants there is a characteristic temperature (Krafft Point, KP) below which their solubility is too low for micellization. In a previous study, the effect of pH on the KP of dodecylammonium chloride in water was determined [Q. Dai and J.S. Laskowski, Langmuir, 7, 1361-1365 (1991)]. This paper deals with the effect of electrolyte concentration on the KP of dodecylammonium chloride. The derived theoretical relationship between the KP and the critical micelle concentration (CMC) for dodecylamine can be used to calculate the KP for electrolyte concentrations of up to 0.5 mol/L (about 8% NaCI-KCI brine). A simple experimental procedure for the determination of the KP for higher electrolyte concentrations is also described. The results show that the Krafft point of dodecylamine increases from about 17-18°C (in distilled water) to about 80°C at 16% brine saturation.

Jan 1, 2006

By Z. Tang

A collaborative project was performed between NRC Institute for Fuel Cell Innovation and MagPower Systems Inc, to develop a cost effective fabrication process to manufacture the anode for magnesium-air fuel cell with improved performance. A novel fabrication process was developed, which resulted in a porous microstructure with increased surface area, instead of the traditional solid structure. This porous anode greatly increased power density in the magnesium-air power source. This fabrication process is very simple and cost effective. Especially, this process makes it convenient to incorporate different alloying additions, as well as hydrogen inhibitor and electrolyte management additive into the anode. The anode composition was designed so that micro galvanic cells were formed as current is drawn out of the fuel cell, and resulting increased dissolution rate of Mg. It is feasible to incorporate hydrogen inhibitor and electrolyte management additive into the porous anode, and the anode with some kinds of inhibitors exhibited improved electrochemical performance. This paper describes the microstructure and electrochemical performance of anodes with designated porous structure and alloying additions. Furthermore, quantitative kinetics analysis of the obtained I-V curves and electrochemical impedance spectroscopy were carried out to clarify the mechanism.

Jan 1, 2005

By A. R. Hekmat

Hypereutectic Al-Si alloys are used in applications that require high resistance to wear and corrosion, hardness and low coefficient of thermal expansion, To maximize the properties of these alloys, semi-solid processing can be utilized to modify the solidification structure of the primary silicon crystals as well as to reduce microsegregation and porosity, The transformation and spheroidization of primary Si crystals by shearing in the semi-solid state are not fully understood as they precipitate in the presence of other alloy phases, The objective of the present work is the determination the rheological characteristics of A390 (Al-17%Si-4,5%Cu-0.5%Mg) alloy using a Couette type (Haake RV12) viscometer and examining the microstructural evolution during continuous cooling and isothermal shear rate experiments, The effect of shear rate, solid fraction (temperature) and morphological evolution of the silicon crystals are investigated.

Jan 1, 2005

By J. K. Atherton

If the metals sector is to contribute successfully to sustainable consumption we must adopt principles and practices which address the entire life cycle of the materials we produce. Progress must be founded on a sense of shared responsibility for the resources we utilize and the materials we create - it is this integrated approach which lies at the heart of materials stewardship. Materials stewardship means mining and metals companies producing materials in a responsible manner and then working with others, beyond their site, to ensure that the downstream material flows and applications are managed properly to create maximum societal value. In September 2006 ICMM published 'Maximizing Value: Guidance on implementing materials stewardship in the minerals and metals value chain'. This document takes a practical view presenting structured guidance as well as good practice case studies. In the publication, materials stewardship is described in terms of the range of activities that can be undertaken to ensure that all parties work collectively toward the responsible use of metal and mineral resources. This paper introduces the materials stewardship concept as set out in `Maximizing Value' and describes the business case for implementation as well as the ICMM framework for promoting materials stewardship.

Jan 1, 2007

By J. W. Kramers, R. A. S. Brown

"Samples from seven test wells distributed throughout the surface-mineable area of the Athabasca Oil Sands have been evaluated to determine the amounts of heavy minerals present and the titanium and zirconium contents. The samples were treated to yield the size distribution of the titanium and zirconium minerals as well as their spatial distribution. The study has shown that heavy minerals are found throughout the surface-mineable area; concentrations range from 0.24 to 2.29 per cent (by weight), with a mean of 1.02 per cent. Titanium and zirconium contents vary throughout the area, and are found preferentially in the finer size fractions. •on the basis of preliminary calculations, the tailings streams from an oil sands plant would provide sufficient feed for a large-scale titanium pigment plant, and the tailings from one plant would provide sufficient zircon feed to satisfy Canadian demand for. metallic zirconium. Variability of the heavy mineral content and composition is such that the heavy mineral potential must be evaluated in detail for each mine site."

Jan 1, 1976

By D. J. Houlahan

ABSTRACT Sorting has the potential to massively improve the pro?tability of mining base metal, hard-rock ores. However, several barriers to the increased application of sorting have been identi?ed, including a lack of mineral-speci?c sensors available to the industry. This paper presents the outcomes of acollaborative project to develop an induction-balance sensor speci?cally for low-grade copper and nickelores. A review of the basic principles of induction-balance sensing and of the sensor-rock interaction is presented. Early development and testing of the sensor on ores from the Thompson nickel belt in northern Manitoba is discussed. Shortcomings of the prototype identi?ed in early testing have now been over-come, leading to improvements in design and construction, as well as sensor accuracy. The improve dsensor has now been tested on additional ores from the Sudbury Basin, with good results. A discussion of potential applications is presented and recommendations for future development are made.

Jan 1, 2010

By L Mariani, G. Mendoza-Suarez

In this investigation, TiH2 powders were coated with copper and nickel by electroless plating to delay hydrogen evolution. Copper-coated samples were found to have a mixed acicular (2D growth) and cauliflower (3D growth) morphology whereas the nickel-coated samples had a cauliflower morphology. Examinations of the coated powder cross-sections revealed that the coating thickness ranges from 0.2 µm to 4 µm. Uncoated areas on the powder surface and coating flakes unattached to TiH2 particles suggest poor adhesion between the coating and the substrate. The phase transformation undergone by the TiH2 during dehydrogenation was studied in samples taken at intermediary points in the heating cycles and examined by XRD. The findings reveal that as the powder is heated from room temperature to 800°C, it changes from TiH1.971 to Tiu and to aTi. Differential Thermal Analysis (DTA) was performed to study the effects of the coatings on the temperature of hydrogen release. It was found that increasing the number of plating iterations, and therefore the thickness of the coating, creates a significant shift in the temperature of gas release.

Jan 1, 2006

By L. C. Johnston, J. N. Gills

This paper reviews the basic reactions of the blast furnace and the open hearth furnace, and then discusses the quarrying and sizing requirements of the limestone feed for each. Particular emphasis is placed on the lime-stone at Irish Cove, now being mined under an agreement between Scotia Limestone Limited and Dosco Steel Limited. The drilling and blasting operations are described, along with loading and haulage, plant flow, water supply, power supply and transportation facilities.

Jan 1, 1967

By D. Auerswald, M. Kotze, V. Yahorava, T. Udayar

Uranium can be recovered from lower grade uranium ores (<800 mg/kg U3O8), leach residues, and waste dumps cost-effectively via resin-in-pulp (RIP). Using this technology, no solid/liquid separation or washing of the leach residues are required. Furthermore, the uranium recovery can be higher than with conventional methods. RIP technologies have, however, been perceived negatively due to concerns around potential resin fouling and losses. This paper highlights the advancements made in RIP and discusses a number of potential applications where the technology could deliver economic and consequential environmental benefits by reducing the uranium levels in the waste.

Jan 1, 2014

By D. Ortiz, J. R. Frias, E. D. Mast, J. J. Fañas

Falconbridge Dominicana (Falcondo) has operated an integrated tpy nickel laterite mine and ferro-nickel processing plant since 1972 in the Dominican Republic. The operation includes mining, a processing plant, an oil refinery, and a power plant. Falcondo has improved process efficiency over the years via modernisation and better understanding of the process. The present business environment of high fuel prices and high nickel prices present a challenge and an opportunity to Falcondo&apos;s operation. This paper gives an update of Falcondo&apos;s process, improvements in energy consumption, factors affecting energy consumption and how Falcondo is facing up to the current business environment.

Jan 1, 2005