Search Documents

By A. Warczok

Chalcocite concentrate obtained by magnetic separation and flotation of Bessemer matte is processed in the Inca top blowing bottom stirring MK reactor into semi-blister copper. The semi-blister is then converted into blister copper in the multi-purpose vessels (MPV) by oxidation of iron, nickel and sulphur. High melting point NiO and Fe30 4 are formed inside the MPV s, which together with Cu20 and smaller amount of fayalite are the major constituents of the solid mush. The accumulation of solid mush and buildup requires periodic MPV cleaning by adding reductant and copper-nickel matte, a unique process called "washout". Various reductants and their combinations, such as pig-iron, 15%Si Ferro-silicon and 50%Si Ferro-silicon, have been used for the reduction of solid mush and buildup. The possibilities of using calcium carbide as a reductant and slagging flux were examined experimentally at the crucible scale. The rate of reduction of MPV buildup was determined by continuous measurement of CO and C02 contents in the offgas and the flowrate of argon carrier gas. The rate of the buildup reduction with calcium carbide was approximately five times faster than the rate of reduction with coke. Additionally, the formation of CaO results in the melting of reduced buildup and formation of a slag at 1300°C and higher temperatures. It was found that simultaneous silica addition enhanced the melting and slag formation. The results showed the strong dependence of the reduction rate on temperature. Activation energy is approximately 225 kJ/mol. Expected benefits of using calcium carbide are related to cost saving on reductant, significant acceleration of solid mush reduction, and reduced amount iron input from reductant.

Jan 1, 2007

By D. Campbell

Mining activity is increasing in northern boreal and subarctic regions of Canada. This is the case in the far north of Ontario, especially in and near the Hudson Bay Lowland (HBL). De Beers Canada opened the Victor diamond mine in the centre of the HBL in 2008, and advanced exploration and impact assessments are occurring to the west in the ?Ring of Fire? for ferrochrome, nickel/copper, iron/ vanadium and platinum-group elements, making it one of the richest mineral finds in Canada in recent years. However, the HBL is also a near-pristine, sensitive environment. Its peatlands forms the third largest wetland in the world and are globally important stores of terrestrial carbon. Human populations in the region are sparse, consisting almost entirely of First Nations communities. Local First Nations also have a strong land ethic and greatly influence mining developments. Through formal agreements, they have insisted on a gold standard for environmental management, including a small mine footprint and the return to representative native ecosystems after mine closure. However, knowledge on the revegetation of subarctic and northern boreal ecosystems is limited. Here, we are conducting research at the Victor mine to develop gold standard protocols for the revegetation of disturbed peatlands and mine waste uplands and present a summary of results. We first tested existing protocols for peatland restoration from southeastern Canada. We collected peat-forming plants from nearby muskeg, spread them sparsely over disturbed peatlands and applied a light phosphate fertilizer, but unlike southern protocols, no mulch appeared to be required to produce a representative cover of peat-forming plants within three years. A bigger challenge is the reclamation of uplands made of mine waste back to representative ecosystems. We first characterized reference conditions for uplands in the HBL, which are scarce in the region. Nearby natural uplands were divided into two classes, interior uplands and uplands along river valleys. Multiple parameters were examined at these sites including soil development, bulk density, soil chemistry in the rooting horizons, plant cover by stratum, plant species composition and dead wood. The mean condition and, more importantly, the range of these parameters allow us to set broad targets for progressive reclamation, which will facilitate success. Finally, we characterized local upland plant species through their functional traits to determine their likely abilities to colonize, grow and contribute to ecosystem processes. A classification of species by these simple functional attributes will help restoration managers to select candidate species to meet different goals at different successional stages (i.e. good versus poor dispersers or establishers). Research into these protocols remain in the early stages, but show promise that gold standards can be achieved to ensure that mining wastes can be reclaimed to productive ecosystems.

Aug 1, 2013

By Eiichi Sato, Koichi Kitazono, Hiroshi Masuda, Kenta Higane

"The present study investigated the low-temperature creep mechanisms in ultrafine-grained (UFG) aluminum manufactured by accumulative roll bonding. UFG aluminum with grain size 0.39 µm showed steady state creep even at room temperature under low stresses as confirmed by the creep curves in the strain rate–strain plot. The low-temperature behavior was divided into four regions by three distinctive stresses, sI, sII and sIII: sI (=45 MPa) is denoted as the micro-yielding stress with which dislocations start movement, sII (=85 MPa) the dislocation-multiplication stress above which dislocations multiply with creep deformation, and sIII (=171 MPa) the conventional yield stress above which macroscopic plastic strain is generated. During low-temperature creep, below sI, negligible plastic strain is generated. Between sI and sII, creep deformation with stress exponent 2.5 occurred, which is accommodated by dislocation absorption into grain boundary and grain boundary sliding, similarly to the low-temperature creep of HCP metals. Between sII and sIII, creep deformation with stress exponent 7.0 occurred, whose mechanism is similar to the low-temperature creep of coarse-grained aluminum. Above sIII, power-law breakdown occurred.INTRODUCTIONIt is well understood that the creep deformation brings about at high homologous temperatures (T/Tm) of >0.4, where Tmis the melting point, with diffusion processes. Recently, the importance of aluminum is increasing for cryogenic temperature parts such as a metallic liner or a cap in high pressure-hydrogen vessels, and the presence of creep behavior in aluminum at room temperature has become recognized (Matsunaga, 2013;Kassner, 2015).In HCP metals and alloys, especially intitanium, steady-state creep behavior appears at room temperature with apparent activation energy of1/10 of that for self-diffusion(Neeraj, 2000; Matsunaga, 2009).On the other hand, Kassner (2015) claims that aluminum shows creep behavior at room temperature with apparent activation energy of 4/5of that forself-diffusion, but never reaches the steady state. We should note that it is derived from the data obtained from short-term creep tests of few hour, and Matsunaga (2013) already claimed the presence of steady state in room temperature creep in aluminum with activation energy of 1/5of that for self-diffusion.The mechanisms for low temperature creep are considered different between HCP and FCC metals: in HCP metals, grain boundary sliding is observed and is thought to accommodate piled-up dislocations at grain boundaries through absorbing them. The so-called slip-induced grain boundary sliding occurs with low number of activated slip systems(Matsunaga,2009).On the other hand, in FCC metals, many activated slip systems bring about work hardening with dislocation cell structure formation. In the initial stage of creep, it results in primary creep (Kassner, 2015), but Matsunaga (2013) claimed that once the annihilating of a cross-slipped dislocation to another reaches balance, steady state is established. It has been, however, strongly required to show more convincing experimental verification for the presence of steady state in FCC metals at low temperature."

Jan 1, 2018

By P. Dinham, G. C. Summerton, N. McCulloch, S. Dowling, D. C. Craig

"Development of a process for the treatment of a nickel copper matte rich in the minerals heazlewoodite, chalcocite and bornite has demonstrated significant base metal recoveries and metal separation efficiencies. The determination of chemical and mineralogical changes occurring in the individual leaching stages in laboratory experiments has enabled a better understanding of the complex leaching chemistry. The chemistry and mineralogy of the piloting and laboratory processes are discussed.INTRODUCTIONThe nickel-copper sulfide ores of the South African Bushveld Complex are among the most important Platinum Group Metal (PGM) bearing ores, and contain the world’s largest reserves of platinum. The treatment used in the recovery of PGMs from these ores includes three types of processes, namely ore concentration using physical techniques such as flotation and gravity separation, concentration by pyrometallurgical means, hydrometallurgical extraction of the base metals followed by the PGMs. Following milling of the ore, flotation involves the separation of high value minerals from gangue by taking advantage of the differences in their hydrophobicity. These differences are generally maximized through the use of a surfactant or wetting agent. Concentrates are then thermally treated and melted which brings about physical and chemical changes that enable the recovery of base metals and PGMs. The main aim of the smelting and converting process is to separate and eliminate the valuable metals from the bulk of the unwanted gangue and essentially all of the iron and to concentrate the metal VALUES (into a high grade converter matte. The matte can be further enriched by magnetic separation, producing a PGM-rich magnetic fraction and a base metal-rich non-magnetic fraction. The magnetic fraction is treated by hydrometallurgical processes to produce a PGM concentrate which is further refined to separate and purify the individual metals. The non-magnetic fraction is treated to produce marketable metal VALUES (such as nickel, copper, cobalt and to a lesser extent PGMs. The principal objective of any hydrometallurgical extractive process is to leach the desired elements selectively into an aqueous phase so as to separate them from the bulk of the material. (Crundwell, Moats, Ramachandran, Robinson and Davenport, 2011; Hundermark, Mncwango, de Villiers and Nelson, 2011)."

Jan 1, 2012

By Jerry Gagnon, Matt Burr, Timothy Ellis, Abbas Mirza, Larry Webb

"The mechanical properties of RSR anode alloys (lead-calcium-tin, 009+ and lead-strontium-tin) were investigated as a function of time with an objective of developing lead anodes for use in high temperature electrolytic processes such as in copper liberator cells and in cobalt and nickel electrowinning. At a temperature of 70 oC, the mechanical properties of rolled RSR lead-calcium-tin (PbCaSn) alloy currently used in copper electrowinning decreased gradually while the mechanical properties of rolled RSR lead-strontium-tin (PbSrSn) decreased relatively quickly and stabilized at low strength levels. Cast PbSrSn started off as the weakest alloy but its properties remained stable with time. Rolled RSR 009+ anode alloy showed improvement in ageing properties over the other alloys tested. However, its mechanical properties did not stabilize in the study timeframe of 284 days. Further investigations are planned to study the effect of alloying elements on mechanical properties of RSR 009+ anode alloy over several years as a function of time at 70 oC. The mechanical properties will be evaluated to determine the time at which they stabilize. Comparative plant trials with rolled RSR PbCaSn and RSR 009+ will also be performed in copper liberator cells and in cobalt and nickel electrowinning tankhouses to determine their mechanical and electrochemical performance at temperatures of 65-75 oC.INTRODUCTIONLead-based alloys are the primary anodes used in the electrowinning of copper, zinc, nickel, cobalt and manganese from sulfate-based aqueous systems. Lead anode technology has evolved over the years migrating from pure lead and lead-antimonial alloys to the present day PbCaSn alloys for copper and PbAg and PbCaAg alloys for zinc electrowinning (Prengaman, Ellis and Mirza, 2010). It has also migrated from cast to rolled microstructures in search of improved mechanical properties and higher corrosion resistance. Although great strides have been made in the development of new lead anode alloys and production processes for lead anodes to be used in copper electrowinning, the industry still has some unresolved issues. These relate to the necessity of having higher mechanical properties especially for the lead anodes in liberator cells in copper electrorefining and for cobalt and nickel electrowinning as these tankhouses operate at temperatures of 65-75 oC compared to 40-45 oC in case of copper electrowinning."

Jan 1, 2016

By R. Kaibyshev, I. Zuiko

"The effect of thermomechanical processing (TMP) including cold working by tension or rolling before aging on mechanical properties and a dispersion of secondary phase particles of an AA2519 alloy (Al–5.64Cu–0.33Mn–0.23Mg–0.15Zr–0.11Ti–0.09V–0.08Fe–0.01Si (wt. %)) was examined. It was shown that the use of tension to impart pre-strain =10% in the alloy provides the best combination of properties in peak aging condition of the material. The AA2519T87 alloy processed by tension exhibits the yield stress, ultimate tensile strength and elongation to failure of 425.4±2.4, 475±2.4, 12.1±0.4, respectively. The one pass rolling leads to -5% decreases in yield stress and –20% decreases in ductility. Dislocations serve as heterogeneous nucleation sites for ?'-phase precipitation. The positive effect of tension is attributed to the formation of more homogeneous dislocation structure, uniform distribution of ?'-phase particles with higher aspect ratio. Precipitation of the O–phase plates on {111}a habit plane was detected. In addition it was shown that the low angle boundaries are heterogeneous nucleation sites for ?' and O particles.INTRODUCTION Precipitation-hardened alloys are a commercially important group of the materials because their mechanical properties can be modified by treating and changing the microstructure. Age-hardenable aluminum alloys belonging to the Al–Cu–Mg system are widely used due to their attractive combination of high specific strength, good fracture toughness and enhanced creep resistance attributed to the highly efficient strengthening by the ?'-phase (Palmer, StJohn, Nie, & Qian, 2017). An AA2519 alloy exhibiting superior mechanical properties among high-strength Al–Cu alloys (2XXX-serie) due to minor Mg additives. It is known that, in alloys with high Cu/Mg ratio (=5.6) the classic precipitation sequence (Palmer et al., 2017; Wang & Starink, 2005; Wang et al., 2010) of supersaturated solid solution (SSSS) decomposition occurs: SSSS ? GP zones (Al3Cu) ? ?? (Al3Cu) ? ?' (Al2Cu) ? ? (Al2Cu) (1)"

Jan 1, 2018

By Magella Pelletier

"IntroductionDepuis une vingtaine d'année, les nombreux travaux de géochimie effectués par l'industrie privée et les milieux gouvemementaux ont permis:• de découvrir de nombreuses zones minéralisées a valeur économique;• d'identifier et de vérifier certains patrons de dispersion géochimique au-dessu s de secteurs minéralises déjà connus;• de favoriser le développernent des techniques analytiques;• de forcer le développement d'une mise en carte des résultats d'analyse, qui soit plus adéquat afin de permettre une meilleure interprétation géochimique.L'une de ces cartes géochimiques qui permet le mieux de mettre en valeur les données analytiques et qui fut instaurée au debut des années 80, est la carte d'interprétation géochimique par pondération.Cette carte numérique semi-quantitative, qui est construite à partir des données de base et de l'importance des éléments indicateurs pour une substance donnée, permet d'identifier et de définir des zones possédants de fortes probabilités pour la recherché de sources minéralisées."

Jan 1, 1987

By Yujing Jiang, Xuezhen Wu, Bo Li, Tomomi Iura, Gang Wang

"Yielding bolt has been widely used for rock reinforcement in mining and civil engineering in high stress conditions. However, the interaction mechanism of yielding bolt and matrix mass is still not clear at present, and no analytical model is available to predict its reinforcement effect quantitatively. In this paper, the mainstream yielding rock bolts were reviewed firstly. After that, a coupling model is proposed to account for the interaction between yielding bolt and matrix mass. Based on the plane strain axial symmetry assumption and the incremental theory of plasticity, equilibrium equations and compatibility equations of matrix mass, and also the response of yielding rock bolt are deduced theoretically. The proposed method was programmed in Visual Basic development environment, and a semi-analytical solution for the coupling model is achieved. The reinforcement mechanism of yielding bolt in conventional tunnelling is clearly demonstrated through an illustrative case study. The reinforcement effect of yielding bolt is estimated quantitatively, and the distribution of axial force along the bolt is presented. In addition, the validity of proposed method is verified by numerical simulations. INTRODUCTIONHigh stress in surrounding rock mass can cause serious stability problems such as massive squeezing in soft rock and rock burst in hard rock. It is observed that many conventional rock bolts failed when experiencing large displacement, which implies that they are too stiff to sustain large deformation and dynamic conditions (Stillborg, 1994; Hoek et al., 1995). Yielding bolt, which can also be called energy-absorbing bolt, has been widely used for rock reinforcement in mining and civil engineering for these conditions (Neugebauer, E., 2008). This paper focuses on the static reinforcement effects of the yielding bolts with analytical method and numerical simulations."

Jan 1, 2015

By S. Hopkins, J. Nolan, S. Gillis

"Cast in place concrete shaft linings have been used in many salt and potash shafts sunk in North America over the last 100 years. A large number of these shafts have exceeded their initial design lives and as producers look to extend the life of their operational assets, maintenance costs and shaft downtime will, in many cases, continue to rise unless repair work is undertaken. Successfully implementing concrete liner repair schemes in operating salt and potash shafts is complicated due to their age, environment and time constraints during inspection, detailed design and construction. This paper outlines a general approach to the repair of concrete-lined portions of these shafts, based on lessons learned from the authors’ involvement in a recent repair project. INTRODUCTION Prior to the recent boom in potash mine construction many of North America’s potash mine shafts were entering their sixth continuous decade of production (Table 1). Of North America’s salt mines, one has been in continuous production, for nearly nine decades.As would be expected, considering the environment in which these liners operate and the age of the material, the concrete-lined sections of the shafts outlined in Table 1 have been noted by the authors to have lost both cross-sectional thickness and strength over time. Since construction, three principal factors have contributed to this loss in section/strength; (1) physical degradation (impact, freeze/thaw or rebar expansion), (2) chemical degradation from brine/water inflows (Neville 1969; Bothwell, 1972) and (3) overstressing of the liner. These factors may act in combination, in which case they can produce more significant distress than individually. Physical degradation There are three main causes of physical degradation of concrete shaft liners. The first is impact from falling debris/tools or equipment (whether large or small), which may damage specific sections of concrete lining as they fall through the shaft. Impacts tend to damage infrastructure fixed to the shaft liner more than the liner itself, so damage from this mode of failure is usually localised, for example, where bolts fixing a shaft services bracket to the wall have been pulled away, pulling out the concrete around the bolts with them."

Jan 1, 2019

By Ralf M. Kleine

THE property of Consolidated 1 Discovery Yellowknife Mines Limited, (Figure I) is situated in the Northwest Territories, approximately 50 air miles north of the town of Yellowknife. The mine is reached by a shaft which extends from surface to a depth of 4,000 feet, with working levels established at 1 50-foot intervals. Stopping operations are carried on throughout a vertical range of 2,000 feet, with both shrinkage and cut and fill methods being used, depending on the ground conditions. Production started in 1950 and milling is done in a 1 65-ton per day cyanide plant. During ten months of the year, the property is serviced entirely by air, utilizing charter aircraft from Yellowknife. A 4,000-foot runway near the mine was constructed from mill tailings. This strip is adequate to receive Bristol freighter planes carrying heavy loads. Other servicing is done by Otter aircraft, equipped with skis or wheels for winter and with pontoons for summer operations.

Jan 1, 1962

By K. K. Panthi, P. K. Shrestha

"Displacement of rock mass around a tunnel opening varies according to the rock mass properties, insitu stress conditions and applied support in the tunnel. Such displacement is also altered by presence of bands of rock mass that differ in properties. This paper focuses on the deformation behavior of rock mass around tunnel openings at four tunnel sections in Kaligandaki headrace tunnel where extensive instrumentation was done. Based on the actually measured tunnel displacement records and actually measured support pressure; back analysis has been done to estimate rock mass properties and insitu stresses. Numerical analysis has been done to analyze and assess the deformation behavior of the rock mass around the tunnel sections.INTRODUCTION Instrumentation and monitoring of tunnel convergences have significant importance in evaluation of tunnel stability. One of the key aspects of monitored data is that early convergences can be used in estimation of long term convergence. In addition, these data can also be used in evaluation of rock mass parameters and in-situ stresses around the tunnel. Convergence around a tunnel periphery may vary according to rock mass quality. Presence of bands of different rock mass may hinder the displacement pattern in the tunnel. Particularly, displacement characteristic of tunnel periphery in schistose, foliated and deformed rock mass is altered by presence of bands of comparatively stronger rock mass, e.g., quartz veins or presence of shear seams or faults. Similar observations were also recorded in monitored tunnel sections in Kaligandaki headrace tunnel, located in the Nepal Himalayas. Extensive monitoring was done by installing multiple point borehole extensometers (MPBX) at three different locations of the tunnel periphery at four different tunnel sections. In addition, convergence measurements by tape extensometers and installation of pressure cells to record support pressures were also carried out at each of the tunnel sections. Observations showed that the tunnel convergences varied according to rock mass quality, in-situ stress and effective support pressure.Rock mass parameters and stresses have significant role in the extent of tunnel deformation, but these parameters are often unknown or difficult to predict. Back analysis based on actual tunnel displacement records and known support pressure is believed to be an important method in such endeavor. This paper performs back analysis to evaluate rock mass parameters and discusses correlation of rock mass behavior with tunnel deformation and applied support. For this purpose, the rock mass parameters are estimated from actual tunnel displacement records, mapped rock mass quality records and laboratory tested data. Then, numerical modelling is conducted to correlate post peak behavior of the rock mass with actual tunnel displacement."

Jan 1, 2015

By Anoop Sattineni

Over the past decade the use of BIM in the AEC industry has grown several fold and with it the number of standards available for implementing BIM. The ?National BIM Standard? by buildSmart Alliance, the ?Contractor Guide to BIM? by the Associated General Contractors of America, the ?BIM Project Execution Planning Guide and Templates? from Penn State University, the ?BIM Roadmap? by the US Army Corps of Engineers are some of the several BIM guidelines that are currently available to the AEC industry practitioners. Some of these guidelines are as comprehensive as defining BIM and the associated taxonomy while others are meant to be used on an individual project basis. From a contractor?s perspective one of the key benefits of using BIM is for the purpose of collision detection and coordination. This research has found that currently available guidelines do not address these issues adequately. For instance, the currently available guidelines do not allow the subcontractor to quickly communicate issues such as naming conventions and color schemes within the model, to the general contractor. Consequently general contractors and sub-contractors find themselves making changes to their BIM deliverables based on each other?s abilities and levels of adoption, apart from reason?s stemming from use of different software platforms. This paper describes how a group of contractors and subcontractors from Atlanta and Birmingham in the United States came together to create and adopt a ?Coordination Guidelines for Virtual Design and Construction?. These guidelines were specifically created with the purpose of streamlining the construction coordination process using BIM. This paper describes how the guidelines created differ from other guidelines currently available in the industry.

Aug 1, 2013

By F. L. Thompson

MAN has been using lubricants of one type or another for at least four thousand years, and probably for a much longer period. We have learned from the inner wall of the tomb of Tehuti-Hetep, on which is a decoration illustrating the method of moving a great stone statue, that as early as 1650 B.C. lubricants were used to facilitate the movement of heavy loads. The Egyptians had available nearly every animal oil and fat, as well as at least thirteen vegetable oils, of our time, all used for food products and in the arts. Examination of the deposit on the axle of a chariot from an Egyptian tomb of 1400 B.C. showed it to consist of animal fat, quartz, sand, iron, and compounds of aluminium and lime-indicating a manufactured lime-soap grease made with lime-soap and possibly tallow. This would not be a bad lubricant for the axles of chariots which had to travel over sandy soil in hot weather. As to the method of grease application, it is remarkable that, from the time wheels were first used in the far distant past up to the present day, no one has ever thought it necessary to design a seal to keep the lubricant in and the dirt out. While time certainly marches on, we have today, in waggons throughout the world, exactly the same form of lubrication as was used in the earliest chariots. From the early days of the chariot until shortly before 1800 A.D. (when the steam engine was introduced), the main heavy equipment required for mining purposes, for machines of war, etc., was made of wood. The bearings were rough, but usually they had metal in the lower half. Light machinery was made of bronze, brass, or iron. Large clearances and poor alignment, plus the fact that speeds were much below present-day demands, combined to provide conditions that were quite satisfactorily met by the lubricants available. These were often produced locally by the machine operator. In northern countries, lard oil, prepared from the fat of hogs, was the universal lubricant employed in machine shop, as a belt and leather dressing, and for cutting operations. Sperm oils were used for light machinery, whereas beef and mutton tallow were more generally employed for the largest bearings. For the early steam cylinders, a slug of heated beef tallow was injected wherever the cylinders gruntingly complained of a lack of lubricant. Southern countries, however, resorted to the use of vegetable oils-olive, cocoanut, etc.

Jan 1, 1940

By F. E. Millett

The following notes deal chiefly with changes from steam to electric drives, or, in the case of the Bellevue pumps, from air to electric. Where electric power can be purchased or generated cheaply it can be used to advantage and is generally more economical than steam, especially in places remote from the central power-plant. Nothing could be more simple than the operation of electrical gear. It does not require a competent engineer constantly on the alert, oiling and watching bearings, and maintenance is at a minimum. The ease with which the current is transmitted from its source to where it must do its work is one of its greatest advantages. Transmission losses are very low. Generally speaking, the smaller the plant the lower the loss and 90 per cent, and better, efficiency is easily attained. In and around Bellevue 2300-volt, three-phase, is the standard distributing pressure; our power requirements and the distances transmitted, for the present, do not require more than this. Most of the heavier motors are 2300-volt .machines, which eliminates the cost and possible troubles of step-down transformers, and makes for a cheaper and less bulky motor. This applies to two fan, two hoist, and two compressor motors, the smallest being 75 and the largest 520 horse power. The standard pressure on power lines to all inside pumps is 550 volts, and 220 volts is general for the the tipple. While 110 volts is used for house and office lighting service, it is not economical around and in the mine. No matter what kind of device is used to lock and protect the lamps, they are invariably missing.

Jan 1, 1926

By Duanyou Li, Qing Xiao, Zhiwang Wang, Xiaoqing Gan

"Seepage is a major cause of earth-rockfill dam failure. Numerical simulation of infiltration process, distribution of drift, flow velocity and direction after the impoundment can guide seepage control and evaluate its effects. A double field coupling model is established based on soil consolidation theory and the interaction between the seepage field and the temperature field. The simulation is implemented under the situation of core wall setted, core wall not setted, and core wall setted with concentrated leakage. The results indicated that the saturation line height was significantly reduced due to impervious core wall, and the temperature distribution is uniform above the saturation line. If concentrated leakage occurs, temperature distribution of dam was significantly changed, which is consistent with theoretical inference.INTRODUCTIONEngineering seepage field distribution must be calculated in seepage control design, optimization, and correction of new engineering construction of earth dams, as well as in seepage monitoring and evaluation of existing earth-rockfill dams. The aim of calculation is to identify the important parameters in seepage field, such as the coefficient of permeability, seepage flow, pressure, head, and allowable seepage slope, for effectively implementing seepage control design, correction, safety assessment, and anti-seepage reinforcement. These seepage parameters usually can be obtained by in-situ test and back-analysis based on reliable monitoring data.In order to obtain reliable monitoring data and reflect the earth-rockfill dam seepage state and change process, appropriate monitoring technology and monitoring method is necessary. The traditional seepage monitoring method is through site inspection and sensors (e.g., osmometer, piezometric tube and measuring weir) that buried in the structure and its foundation. However, there are still some disadvantages:"

Jan 1, 2015

By S. Hill

For a mining operation, the determination of the best place to build haul roads is typically done by hand, or with the assistance of rudimentary shortest path optimisation algorithms. Straight line, point to point, modelling of costs is often used with distances multiplied by constants that are based on rise of the road between the points. Failings of this approach are that straight line approximations are notoriously poor as they do not take into account areas where a truck cannot travel. In addition, the rise and fall of the road may vary considerably over the truck journey meaning acceleration/deceleration and varying truck speeds are not taken into account. Lastly, the use of rudimentary optimisation algorithms means properties a truck must obey such as minimum turning circles, line of sight restrictions or even that the truck must travel forward at all times are not taken into account. Thus solutions generated may not be feasible, let alone optimal. In this paper we discuss a state of the art parallel Artificial Intelligence tree search technique for solving haul road location problems. As well as the above properties, factors such as road utilisation, cut and fill, and construction costs are taken into account. The combination of advanced modelling and fast computing and optimisation techniques produces significant benefits both in terms of time to generate roads and cost savings. Preliminary results where this method has been used are discussed.

Aug 1, 2013

By G. Bourque

One of the design criteria for the Mount Wright facilities was to incorporate the latest proven automation techniques and devices for the new crushing, grinding and concentrating plant. The heart of the centralized control system is a Fox 1 process computer, located in the central control room in the administration building. The entire operation, i.e. crushing, conveying, storing, grinding and concentrating, is monitored and controlled, through the process computer , by one operator via a CRT console. In case of computer failure, the control is automatically, and without process interruption, transferred to manual back-up panels. One of the newest management tools, the process computer is programmed to collect and automatically print out shift. daily and monthly reports on tonnage, metallurgy and equipment operating time, for better planning of operations and preventative maintenance.

Jan 1, 1977

By J E. Gordon

For many years, it has been known that certain loud noises may, with prolonged exposure, temporarily or permanently damage a person's hearing ability. Pneumatic rock drills, al-though among the offenders, have, until recently, remained unaltered and unrestricted as to noise output. Now, there are drills available with higher rates of penetration and yet with noise levels reduced to those of previous models or less. Use of such drills, when proved to be superior in noise attenuation and of acceptable performance, should be encouraged in order to reduce future hearing losses to a minimum. People Have the Right to Hear P ERHAPS the earliest recognized indication of hearing loss due to industrial noise was the deaf-ness developed by the workmen in boiler factories. Here, the vibration set up in the shells by the riveting hammers gradually deteriorated the workmen's hearing, especially those whose job it was to hold the dollies inside the drum, where the sound is greatly intensified by reflection

Jan 1, 1963

By M. L. F. Paullo, S. Cristian Mejia, D. Roehl

"Rock fracture simulation most often presents non-linear behaviour due to loss of material integrity and strain concentration in the fracture zone. These strains generate local instabilities that propagate to the global system of equilibrium equations, generating convergence problems of the numerical solution. Often, in such cases, analyses in the post-critical regime are unfeasible. To overcome the numerical difficulties associated with problems of stiffness loss in the post-critical regime control methods, also called continuation methods, are employed. Among them are the arc-length method, the energy control method and the indirect displacement control method. These methods are employed in conjunction with a Newton- Raphson scheme for the solution of non-linear systems of equations. However, depending on the system instability, convergence in not guaranteed even with very small increments. In the present work these control techniques are investigated in combination with cohesive elements to simulate rock fracture. The constitutive model employed with the cohesive elements represents stiffness degradation through a damage law, which leads to serious convergence difficulties as reported in the literature. Here the continuation methods mentioned are applied to a Mode I rock fracture problem and to hydraulic fracture simulations. The effectiveness of the different continuation methods is compared.INTRODUCTIONThe process of rock fracture induced by the fluid pressure is called hydraulic fracturing. The propagation of a hydraulic fracture is a complex process, which is basically defined by the mechanical deformation of the rock, the fluid flow within the fracture and the fracture propagation itself (Mokryakov, 2011). In the works of Bendezu et al. (2013), Chen (2012) and Carrier et al. (2012), vertical hydraulic fracture propagation is modeled by cohesive elements with traction-separation law. The softening behavior of rock in post-critical regime is demonstrated by experimental testing and is characterized mainly by high strains and low stresses (Crowder and Bawden, 2004). This nonlinear behaviour can arise due to material nonlinearity, such as micro-cracking and damage, leading to softening behaviour (Chandrakant, S.D., 2012). The cohesive fracture model considers in its formulation the softening behaviour that most rocks present in post-critical regime with propagation criteria."

Jan 1, 2015

By J. A. Cox, R. S. Mattson

"One of the main problems encountered in employing sublevel caving is the inherent high dilution factor. The operating results at Granduc illustrate that this dilution can be closely controlled and satisfactory recoveries achieved, in base metal ores grading less than 2.0% copper equivalent, by using an assay grade control system based on the fundamental draw characteristics. The history of draw control procedures employed since the start of operations provides an effective comparison between this system and one based mainly on tonnage. The transverse and longitudinal sublevel caving mining methods are described and it is shown how improvements in design layout, operating practice and draw control in narrow complex ore zones (12-foot minimum width) have raised the operating performance of the longitudinal system to a satisfactory level."

Jan 1, 1973