Search Documents

By D R. Swinbourne, T Lehner

Study of the distribution of minor elements between copper matte andfayalite slag is important in determining appropriate methods tomaximise the recovery of valuable metals and the rejection of harmfulelements. Boliden Mineral AB operate a large copper smelter in northern Sweden, where they had noted that the loss of silver to the slag in the settling furnace appeared to be a direct function of the tin content of the slag. This work was aimed at determining whether or not this was a cause-and-effect relationship. Copper matte containing approximately 50 wt per cent copper and small amounts of silver and tin was equilibrated with silica-saturated fayalite slag at 1250¦C, then quenched. The matte and slag were then analysed for their silver and tin contents. It was found that there was no relationship between the silver distribution and the tin distribution. The silver matte/slag distribution ratio had a value of 120 ¦ 40 while that for tin was 2.8 ¦ 0.3. It is suggested that the most likely cause of the relationship observed at the Boliden smelter was matte entrainment in the slag.

Jan 1, 1999

By H Benzer, N A. Aydogan

It is well known that the high pressure grinding rolls (HPGR) can only be operated efficiently under choke feeding conditions in which a material bed is built up between the rollers to ensure interparticle breakage. By increasing the fines amount in the material bed up to a specific level with the recycling load, a uniform material bed is created and higher pressure gradient along the roller width is obtained which results in compact flakes including more fines. Extensive test work has been carried out with an industrial HPGR unit grinding cement clinker in a cement plant in Turkey. During the test work the recycling load of the circuit was changed to achieve different ratios to the fresh feed rate in order to identify the effect of the recycling load on the circuit performance. Six different tests were performed with the circuit at steady state. For each test, samples were collected from HPGR fresh feed and discharge, and total feed, then the particle size distributions of the samples were determined and mass balances around the circuit were calculated. The conclusion was that the reduction ratio of the HPGR increased with increase in recycling load. The flake densities showed the same trend with more compacted flakes being produced for higher recycling loads.

Jan 1, 2009

Located 350 km west of Sydney and 20 km outside Orange, NSW, lies the Ridgeway Gold Mine û NewcrestÆs flagship Underground Gold Mine. Key to success at Ridgeway has been the fast tracked development of the 3.8 km, 1 in 5.3 conveyor decline which houses the 850 t/hr conveying system feeding the dedicated Ridgeway Concentrator, built adjacent to the existing Cadia Hill Concentrator. Eroc was contracted to develop the steep conveyor decline, drawing on its personnel and experience from past metalliferous, tunnelling and coal mining projects to complete the ambitious schedule within 12 months. This paper deals with the complexities and experiences in safely delivering what is understood to be one of AustraliaÆs steepest declines of any substantial length in a metalliferous mine.

Jan 1, 2002

By L J. de Lange

As a material asset for mining entities, the resources and reserves (RR) estimation processes are surprisingly underrepresented in the assurance landscape. When press reports expose them being inaccurately reported, or in merger and acquisitions processes, their importance becomes clear. The impact of erroneous RR numbers (both positive and negative) could have a material impact on an entity’s reputation and value.The technical nature and ‘black magic’ connotations of the RR estimation processes are possibly reasons why audit committees are not actively involved with it. Internal auditors avoid the RR processes for similar reasons. Also the traditional approach to obtain assurance on RR is expensive and is therefore only performed when it is absolutely required.However, stakeholders’ expectations of good governance are growing. Part of this increased focus is based on attaining a higher degree of certainty about the current and forecasted position of the entity. Stakeholders are also increasingly more interested in non-financial areas of entities, as the future success of an entity is more than a set of financial metrics.Consequently, the RR estimation processes should be visible on the agendas of audit committees. Monitoring of key controls is required as part of the governance obligations for senior management and the audit committee. So once it is on the audit committee’s agenda, the question then becomes, how will that agenda be supported by an assurance process that is cost-effective?The main objective of the paper is to describe a model of RR assurance that has been effectively applied in some mining companies. The paper discusses one particular approach that provides an audit committee with the required assurance regarding RR processes. The approach ties the assurance needs of the audit committee to the needs of the technical experts in the entity, therefore involving two important figures. It also offers assurance providers with a model to audit ‘through’ the RR processes rather than ‘around’ them. The paper then discusses top-down and bottom-up approaches that provide assurance at different levels of an entity.A governance audit that focuses on the RR processes is suggested as a top-down approach. A bottom-up approach assesses the design adequacy of internal control processes. A hybrid model is described which meets the needs of diverse stakeholders including the audit committee and the RR community.The hybrid model combines the expertise of professionals in both internal audit and RR. The right balance of these skills directed by a singular approach ensures that a credible result is achieved.This approach is not as expensive as some verification approaches used in the industry and can, as a result, be performed on a more regular basis.The last element of the paper looks at implementation of the reporting mechanism. An assurance process aimed at continuous improvement further enhances the robustness and reliability of RR reported by an entity.CITATION:de Lange, L J, 2016. Resources and reserve assurance processes – a framework for improved governance, in Proceedings International Mine Management Conference, pp 21-34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By S M. Jowitt, G M. Mudd

"The mining industry is the source for the vast majority of the metal, mineral and energy resources we use on a daily basis. New deposits are discovered over time and are developed into mines before being rehabilitated – a sequence that when repeated can help contribute to the noble notion of ‘sustainable development’, despite the generic concept of mining being the unsustainable consumption of non-renewable resources. The scale of the modern mining industry is immense – from iron ore and coal to base and precious metals, modern mines are sometimes hundreds or thousands of times bigger than their long lost historic ancestors. We also live in a world with emerging and increasing demands for so-called technology metals (aka ‘critical’, ‘e-tech’ or ‘specialty’ metals) that are needed to feed the rapid growth in renewable energy (especially solar photovoltaic panels and wind turbines), consumer electronics, sophisticated military technologies and super alloys, amongst other uses. These elements include the rare earth elements, indium, germanium, tellurium, rhenium, selenium, gallium and many others, most of which had few or no known uses in the recent past. Although the mining industry has been successful in developing ever larger mines and increasing the scale of production, the key issues underlying the future of the industry are declining ore grades, increased tailings and waste rock generation, the presence of toxic or other impurities, balancing the economics of primary and secondary products, stricter environmental conditions, more difficult exploration, increasing community expectations, as well as the processing of more complex or refractory ores, let alone the recent volatility in world commodity markets. Here, we synthesise our recent research on many of these various issues, focusing on the need to link all areas within the mining chain from mineral resources through mining to environmental performance in order to ensure we obtain the most out of our modern mining effort. The paper presents a unique and detailed assessment of the sustainability challenges and opportunities facing modern mining – and geometallurgical thinking is at the heart of this conundrum.CITATION:Mudd, G M, Jowitt, S M, 2016. From Mineral Resources to Sustainable Mining – the Key Trends to Unlock the Holy Grail?, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 37–54 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

The modern resource extraction enterprise is a complex capital intensive business operating in a world of constantly evolving social, environmental and economic scrutiny. Investors, government, media and special interest groups expect to see business environmental and social performance respond and deliver increasing corporate responsibility and sustainability.   Thorough interrogation of business performance using a multi-disciplinary due diligence approach presents a more sophisticated review and benefits beyond the traditional compliance/conformance 'audit' style assessment.   Using a due diligence approach allows assessment through a comprehensive lens which examines potential short- and long-term risks including sometimes less tangible environmental and social liabilities, and informs management, investors and regulators of broader business performance. This approach provides information in a form that business can measure performance in a repeatable and enterprise wide sense.   This paper provides an outline of the due diligence process applied in this way, drawing from lessons learnt and industry based experiences in the due diligence process and the benefits and tools that can  be applied in an environmental and social due diligence business performance assessment

Jun 1, 2010

By C Bie, S Li, P Xiao, P Zhao, H Lin

"Based on solid simulation material research, the simulation conditions for methane and coal solid-gas coupling were obtained using solid-fluid coupling theory. Using sand as the aggregate and paraffin and oil as the cementing agents, a material suitable for solid-gas coupling simulation was developed. A permeability testing instrument was also developed, and the compressive strength, brittleness parameters and seepage velocity of material were tested with different aggregates. The results showed that as the paraffin content increased, the compressive strength of the material increased but the permeability decreased. The oil removed the drawback of intensely changing material compressive strength. By setting a different ratio of aggregate to cementing agent, it can simulate rocks with different strengths and permeability. Applying the material to a mining simulation experiment revealed a relationship between methane seepage velocity and overlying strata movement. By extracting pressure relief gas from Shanxi Tianchi coalmine drainage, the authors found that the mining fissure zone was a storage area of pressure relief gas, and a gas drainage system can be placed to achieve good results. CITATION: Li, S, Zhao, P, Lin, H, Bie, C, Pan, H and Xiao, P, 2015. Character of simulation material of coal – rock and gas solid-gas coupling and engineering application, in Proceedings The Australian Mine Ventilation Conference, pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

In this paper the system of an operative expert estimation of innovative policy of mining enterprise technological development on sustainable development principles, created in the laboratory of economic analysis, planning and management of Mining Institute after D A Kunayev is represented. It is based on application of technology of satellite navigation and global positioning system (GPS). It allows to estimate the geotechnological complex functioning efficiency in the automated mode and on the basis of the obtained results to develop a complex of management measures on the competitiveness increase, realised by means of the automated corporative management system of geotechnological complex. The estimation of complex competitiveness is carried out on such basic aspects, as: technical, technological, organisational, ecological and economic as all of it give certain expenses and influence on complex overall performance. The major difference of the given approach is its realisation within the limits of the automated corporative management system of geotechnological complexes. It is based the fact that data of monitoring of complex's work will provide a sustainable development of geotechnological complex of mining enterprise.

Dec 6, 2010

By J Rowland

"This paper was primarily put together in order to demonstrate what are believed to be acceptablestandards, in relation to ventilation surveys and the subsequent model assembly process. Thiswas brought about by the fact that in many parts of the world it is regarded as acceptable to carryout ventilation surveys and then build and supply the client with a æstick fi gureÆ type ventilationmodel. Such stick models have arguably litt le use and a very short life span in the real world and isalmost impossible for site staff to maintain. Thankfully most underground coal mines in Australia strive to maintain a true replica model of their ventilation circuits and to keep them in a relatively good state. Given that these mines own and maintain the models, it is often seen as necessary to update or rebuild them. The level of survey detail required to do so is totally dependent on the end use of the data and the criticality of the accuracy of the data set, to the ongoing safety and viability of the business. Mine technical personnel should think clearly about the use and importance of the ventilation survey and subsequent report outputs required that will help them bett er understand their mines and bett er prepare them to manage their ventilation circuits, on an ongoing basis. This paper provides some guidance for Australian ventilation engineers so they may plan and execute this work æin houseÆ, should they rightly choose to do so. To this end, methods of data collection and circuit analysis required for surveys of a high order of accuracy are detailed. Also, some of the issues which are important when formulating a strategy to carry out the appropriate ventilation survey for the required purpose are summarised. As well, the major details that should be furnished within any survey and some survey/report outputs and/or omissions, which are clearly not acceptable, are highlighted."

Jun 1, 2012

By K B. Quast

Changes in feed size distribution can have significant effects in rod mill grinding. The product sizing resulting from wet batch milling of a tin ore showed little influence on fines production after truncating the feed at either the coarse or fine end. The addition of fine material caused a less amount of fines to be produced and a possible increase in grinding at coarse sizes, although this is complicated by the changing feed size distribution. The changes in feed size distribution caused no tendency for preferential grinding of the cassiterite.

Jan 1, 1998

The Horn Island gold and mineral field produced 194 kilograms of gold in the 4 years subsequent to its discovery in 1894, from an area of shallow workings 1.5 kilometres x 0.5 kilometres. Gold deposits in the adjacent Prince of Wales, Hammond and Possession Islands also drew attention at that time.These islands form part of a Carboniferous sequence of ignimbrites (Torres Strait Volcanics) intruded by the Badu Granite and minor volcanics within the Cape York-Oriomo Ridge. Gold is associated with the epithermal stages of igneous activity. Recent exploration has defined sub-horizontal zones of disseminated gold mineralisation in the sub-surface, as well as reserves in the outcropping sub-vertical structures mined in the past. Released estimates of 170,00 tonnes proven ore and 550,000 probable ore at 4 grams per tonne gold, have been established.Gold is mostly contained in quartz vein stockworks and hydrothermal breccias within the intensely propylitised medium grained granites which form the local host rocks within the coarse grained Badu Granite. Associated vein minerals are sulphides (primarily of lead, zinc and iron) and calcite. Various intrusions of porphyry, aplite and granodiorite occur through the prospect area.

Jan 1, 1986

By Wong KY, Woodcock JT

Previous results have shown how con- trolled-potential sulphidization (CPS) can give improved metallurgy during rougher flo- tation of mixed oxide-sulphide copper ores. Results in this paper, using different samples and different equipment, confirm the previous results and extend the application of CPS to cleaner flotation. By using CPS, faster flotation of copper minerals (chalcocite and malachite) from clay was obtained in roughing and cleaning, and improved concentrate grades and recoveries were achieved over those by conventional manual control. The optimum sulphidizing potential (i.e. the potential of a sulphide ion-selective electrode versus a saturated calomel electrode) was -500 mV, and could be controlled to ¦5 mV, during four rougher- scavenger and three cleaner-re cleaner stages. This optimum gives the best balance between copper recovery, concentrate grade, and sodium sulphide consumption. Five cleaning circuits and five ore com- posites of different composition (0.55-1.50 per cent Cu) were examined as well as the effect of feed size and pulp density. Better results were obtained at 20 per cent solids in a Denver cell than at 33 per cent solids in an Agitair cell; this may have been related to the high clay content of the ore. Commercial equipment for pilot plant or full-scale plant application of CPS is cur- rently being developed.

Jan 1, 1986

By P G. Hicks

The influence of feed size and pulp density on the specific rate ofbreakage of quartz was investigated. Plots of log fraction of feedremaining within the feed size interval against grinding time allowed the application of the first order grinding model to be examined. Substantial non-linearities were observed for all feed sizes due to environmental and material factors. For feed sizes above 1.3 mm, the specific rate of quartz breakage was higher with rod milling than ball milling, but below this size the reverse was true. Material that remained in the feed size interval after the initial grinding broke more slowly in subsequent grinding than the original feed material. Grinding media and time as well as feed size influenced the effects of pulp density on grinding. More dilute pulps (eg 50 per cent solids density by weight) were favoured for higher rates of breakage in rod milling but for ball milling, the optimum pulp density appeared to be 60 to 70 per cent solids by weight.

Jan 1, 1998

By G Hancock, A Kemp, I Taylor

The mine site is situated south east of Port Hedland in the Pilbara region of Western Australia. A detailed engineering design was undertaken for six irregularly shaped waste rock dumps at the site. The design was undertaken to ensure long-term stability of the dumps and optimise material movements for closure construction. The Watershed Erosion Prediction Program (WEPP) and SIBERIA landscape evolution modelling was undertaken for the landforms using regional and site-specific material characteristics to provide an indication of the maximum allowable slopes and corresponding slope lengths for long-term stability.The majority of the waste materials present in the waste rock dumps are considered likely to be subgrade banded iron formation (BIF) and chert, which is generally competent material. The presence of a large number of dolerite dyke swarms indicates appreciable volumes of dolerite were produced as waste from the pits. Geological records also indicate that the dolerite is logged as being heavily kaolinised in the geological logging, hence kaolinite is very likely to be present within the waste dumps on-site. This material has an elevated risk of being highly erodible/dispersive. Clays and shales are also likely to be present in the dumps and are considered to be less competent material (relative to the BIF/chert).The final design configuration of the largest existing ‘unplanned’ waste rock stockpile is compared to a hypothetical continuous ten degree outer embankment alternative. This paper will present a brief description of the alternatives for closure of three waste dumps in close proximity to each other and how the detailed design based on site-specific materials and conditions compare to an alternative approach blankly assuming that most materials will be erosionally stable at less than ten degrees.CITATION:Kemp, A, Taylor, I?and Hancock,?G,?2014. Landform design for Pilbara mine site – why plan and design waste rock dumps for closure based on site-specific conditions?, in Proceedings Life-of-Mine 2014 , pp 47–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By R L. Brathwaite

The orogenic gold deposits wall poster is one in a series of posters on different mineral deposit types being produced by GNS Science to raise awareness of the characteristics of New Zealand mineral deposits and their prospectivity. Orogenic gold deposits are typically quartz vein deposits formed in fault and shear systems at crustal levels within and above the brittle ductile transition zone, at depths of 3 12 km and temperatures from 200¦ to 400¦C. In New Zealand, orogenic gold deposits are found in regionally metamorphosed sedimentary rocks of Paleozoic and Mesozoic age. The deposits in Paleozoic rocks include those at Golden Blocks in Northwest Nelson, Lyell and Reefton on the West Coast, and Preservation Inlet in Fiordland. Quartz veins are developed along shear zones that dip steeply and generally strike parallel to the axes of folding in the greywacke and argillite/slate host rocks, although most are discordant to bedding. The lodes are typically less than 1 m wide and extend an average 200 m horizontally and vertically, but the Birthday Reef at Blackwater, Reefton, the largest quartz vein deposit in Paleozoic rocks, averages 60 cm in width and was mined over a strike length of 1070 m, and to a depth of 830 m. Disseminated gold occurs adjacent to the quartz lodes at Globe-Progress and some other Reefton deposits. The deposits in Mesozoic rocks are hosted in schist of Otago and Marlborough, and schist and greywacke of the Southern Alps. The lodes are typically lensoidal, less than 1 m wide and localised along single or multiple parallel shear zones that generally dip steeply, and are discordant to the schist foliation and bedding. A notable exception is Macraes, where the lodes are developed in the semi-concordant, low angle Hyde Macraes Shear Zone that has a strike length greater than 25 km.

Jan 1, 2005

By G Wyartt

In the Pilbara region of Western Australia, an iron ore mine is undertaking a high wall cut-back to improve stability and allow access to deeper ore deposits. Several sections of the wall have been classified low factor-of-safety due to unstable localised geology, and therefore an engineered approach to vibration critical blasting was required. The use of electronic detonators allowed multiple signature (seed) holes to be incorporated into a production blast adjacent to the low factor-of-safety area, therefore providing baseline vibration data to be used for future modelling with the added advantage of eliminating unnecessary pit closure downtime typically associated with a signature hole program. All subsequent blast patterns also incorporated multiple signature holes to provide additional data and allow continual updating – and therefore improved accuracy - of the blast prediction model. Electronic detonators and blast initiation systems were combined with advanced blast vibration modelling software to produce optimal timing sequences with predictable vibration outcomes. Although minimising vibration was the primary focus, blasting induced frequency was also a concern for the project team and therefore initiation sequencing was optimised to also avoid undesirable frequencies. Minor variations in ground factors (vibration transmission and attenuation) were noted, and therefore justified the inclusion of regular signature holes which allowed continual vibration model updates. Blasting results produced vibration and frequency measurements within allowable limits and closely resembled the predictive model. These positive results were achievable through the combination of electronic detonators, advanced modelling software and good onsite practices by engineering and on-bench teams alike. This project will remain ongoing as the pit progresses to deeper benches, and therefore the same methodology will be applied; quality and continual data collection, the use of electronic detonators, and optimisation via advanced vibration and frequency modelling software. CITATION:Wyartt, G, 2018. Vibration control blasting for low stability final walls, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 504–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By K H. Esbensen

Optimisation of a real-time at-line monitoring system for control of industrial granule coating quality is presented. The system is based on a fluorescence imaging system, because fluorescence originates in the interiors of enzyme granules but is significantly quenched by a polymer coating (which is needed due to environmental precautions). We have developed an image analytical system for direct prediction of coating quality, which is based on application of the Angle Measure Technique (AMT) for image complexity characterisation; AMT is briefly described. The first part of the presentation addresses pixel sampling strategies within a digital industrial image, inherent in application of AMT, in which the unfolded image is regarded as a one-dimensional object in analogy with 1D process sampling in Theory of Sampling (TOS). The effects of random, stratified and systematic pixel selections in the unfolded image are evaluated. Also factors such as the fraction of image pixels and the effects of specific unfolding strategies (there are three principal strategies, termed æchopÆ, æsnakeÆ and æspiralÆ respectively) are investigated. It turns out that unsuspected artifacts are sometimes produced, related to the specifics of the unfolding procedure, which interferes with a straightforward 1D TOS process sampling analogy. These artifacts have a wider interest û among others, for 2D sampling û and therefore receive special attention in this presentation. The optimal pixel selection strategy for the AMT algorithm is found to be systematic or stratified sampling (not surprising according to TOS) of 500+ initiating points, but need to be unfolded in the novel spiral- or snake-wise fashions in order to effectively counteract these artifacts. This also has a general impact on various suggested standard schemes for 2D grid-sampling, among others, from the geoscience realms. The second part of the presentation is directed towards optimal image analytical sampling of a continuous series of fluorescent images (imaging of conveyor belts of æinfinite lengthÆ), ie optimisation of process image sampling. The minimum number of images needed to uphold a sufficiently good on-line estimate of the quality control (QC) parameter in question is found to correspond to the relatively high sampling rate of 15 - 20 per cent, which can be shown to be related to an intrinsic very high measurement error level (25 per cent) of a mandated analytical reference method.

Jan 1, 2005

By R Price, B H. Miller

"The rise of autonomous haul truck fleets may have been initially driven by the rapid escalation of the cost of equipment operators, but the actual improvements reported by the major iron ore miners far exceeds the simple reduction in workforce. Utilising cost models developed for feasibility studies and mining contract modelling, the limits of cost improvements due to simple labour reductions are compared to those achieved by the early autonomous fleet adopters and through traditional process improvement techniques such as fleet class upgrades or hot-seating of equipment. As autonomous fleet implementation matures, it is likely that the gains seen by current adopters will seem minor compared to the limits generally governed by the limit of equipment utilisation. This ultimate limit is explored through time utilisation models, which were also developed for use in feasibility studies and mining contract modelling.Citation:Miller, B H and Price, R, 2016. Autonomous Haul System Savings - It's Not about Less Truckies but Better Truckies!, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 2–10 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By J Zhou

This paper discusses the implementation of a mixed integer linear programming model for a coal preparation plant. The plant considered consists of primary and secondary heavy media cyclones, hydrocyclones for intermediate fines and froth flotation for the very fine material. The model is designed to optimise the plant settings and product flows to maximise revenues for a given specification for two product outputs. The model can deal with bonus/penalty aspects of the product pricing for products that exceed or fail to meet specification. We report on a model with two separate coal feeds with parallel circuits for the oversize, intermediate and fines streams. The genesis of this model is more than 30 years old but recent improvements in mixed integer programming solvers make a full mixed integer formulation practical. The original model began as an enumeration of cut points with arbitrary rules for product allocation. The product allocation was improved in a linear programming formulation by Gunn (1982) and Sarker (1991 and 1995). Current mixed integer programming capabilities make it possible to replace the enumeration aspects and solve directly as a mixed integer programming problem. The current implementation uses a general purpose modelling language to formulate the model. Open source and commercial mixed integer programming solvers are compared

Sep 26, 2011

By S J. Schafrik, C Keles, C Schlosser, E S. Gilliland, A K. Louk, N S. Ripepi, S Keim, J Amante, E Diminick

Three legacy coalbed methane production wells have been converted to injection wells for a one-year carbon dioxide (CO2) injection test to evaluate the potential for CO2 storage in the coal reservoir and the potential for enhanced gas production at offset wells. The injection reservoir is composed of 15–20 individual coal seams with an average thickness of 30 cm (1.0 ft), spanning a depth range of approximately 240 (800 ft) to 670 m (2200 ft).The monitoring program for this test includes gas and water sampling of the three injection wells, three dedicated monitoring wells and approximately 20 offset production wells. Key technologies used for monitoring the study area include time-lapse GPS and interferometric synthetic aperture radar (InSAR) acquisitions for surface deformation measurement, a 28-station buried passive microseismic monitoring array, real-time downhole pressure and temperature sensing and perfluorocarbon tracer fluids, which will be injected with the CO2 stream. The schedule for the monitoring program includes pre- (baseline), during- and post-injection data collection. This schedule will allow data to be analysed for time-lapse changes and trends, which are important for understanding the migration of gas and fluid phases in the reservoir – including CO2, methane, other hydrocarbons and water – and for observing the changing distributions of reservoir pressures and stresses.The results of the monitoring efforts for this study have implications for monitoring mining operations. The combined use of GPS and InSAR geospatial data to evaluate elevation changes across and beyond the study area may prove to be an accurate option for measuring surface deformation, including mining-induced subsidence, in unstable terrain. Long-term microseismic monitoring using high-sensitivity instruments has several applications in mining operations, including rock stability monitoring, production monitoring and miner location detection during emergencies. Tracer studies and short-term microseismic monitoring used to assess methane extraction can also be used to develop and optimise degasification systems for underground coalmines.CITATION:Gilliland, E S, Ripepi, N S, Schafrik, S J, Schlosser, C, Amante, J, Louk, A K, Diminick, E, Keim, S, Keles, C and Karmis, M, 2015. Monitoring design and data management for a multiwell CO2 storage/enhanced coalbed methane test in a stacked coal reservoir, Buchanan County, Virginia, USA, in Proceedings Third International Future Mining Conference, pp 47–56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015