Search Documents

THIS paper is the outcome of experiments carried on and experience gained. at the Waihi-Paeroa Gold Extraction Company's tailings plant at Waihi, New Zealand. The plant was erected to treat accumulated tailings which had been discharged into the Chinemuri River by the Waihi batteries.The Chinemuri River is a common sludge channel for all mining debris, tailings, and ashes from the power plants, the last being the cause of occasional high residues, which gave so much trouble to the management. The tailings were dredged from the bed of the river into barges by means of a Pohle air lift, the power being supplied: by a 13 b.h.p. Tangye oil engine driving an air compressor and a centrifugal pump. The sands were elevated from the barges by bucket-belt elevators over screens, to eliminate large particles and rubbish, into storage hoppers, and from there fed direct into four C. Judd Ltd. tube mills.The method of treatment was fine grinding in a weak cyanide solution, agitation in B. and M. tanks, filtration with turn-over vacuum filters, and precipitation with zinc shavings. The comparatively high values of the residues in gold gave a great deal of trouble, 'and it was not until repeated experiments were carried out that the cause of the trouble was located. While the value of silver residues remained stationary, the gold values...

Jan 1, 1912

By Hirst H, McAfee J

In December, 1934, Mr. R. Sussex extruded some silver lead alloy wires in order to determine their electrical resistance. After the determinations had been made each wire was threaded through a sheet of paper on which the composition was noted. The wires were placed in a more or less tangled mass in a cupboard in March, 1935. It was not until September, 1936, that they were re-examined, and it was found that during the eighteen months some of the wires had corroded very badly. It was not until March, 1938, that the wires and the corrosion product could be examined, and the results are given in the following pages. It is of interest to note that none of the numerous silver-lead alloys which have been used for creep testing in the rolled condition have shown a similarphenomenon. The silver content of the rolled alloys was, however, never greater than 0·1%.GENERAL APPEARANCE OF THE CORRODED WIRESThe wires contained 0·1% up to 28% of silver, and a general examination showed that the corrosion had progressed farther the higher the silver content. This can be seen in Fig. 1, which is a photograph taken in March, 1938, of typical wires at a 'magnification of five diameters. In the early stages the corrosive action seems to be localized and an area of grey, yellow or reddish brown powder appears. The grey corrosion product is by far the one, most frequently seen, and in the later stages the only one visible from the outside. The reddish coloured product is sometimes seen on the residual metallic centre when the grey product has been broken away.The irregular extent of the corrosion can be seen in Fig. 2, which shows (natural size) the 5% silver wire after standing two years. The corroded parts are seen to be much thicker than the slightly corroded ones. The corrosion product, being non-metallic, is quite brittle and falls away from the wire on bending. In the extreme case the' whole wire has corroded and presents a cracked appearance as seen in Fig. 1 (281% silver).An approximate idea of the extent of corrosion can be obtained by measuring the diameter of the corroded part. The original diameter in each case was ·050/ ·051 inches and in Table I are given the diameters of the corroded parts after Hand 3 years respectively. When the diameter...

Jan 1, 1941

By C J. Unger, A M. Lechner, A Walton, V Glenn, M Edraki, D R. Mulligan

In Australia, responsibility for abandoned mines can be unclear. With a few exceptions, state and territory governments have become responsible for abandoned mines on Crown land and private landholders are responsible for abandoned mines on freehold land. Abandoned mines pose risks and opportunities across the full suite of sustainability themes (environmental, human health and safety, socio-economic and community development) after mining ceases.Across Australia, there are more than 50 000 abandoned mines recorded, ranging in size from individual shafts to large polluting open cut mines. Addressing the safety and environmental impacts of these sites, as well as the socio-economic development opportunities of significant rehabilitation projects, requires the implementation of effective policies and programs. Qualitatively defined graded scales or ‘rubrics’ have been used for many years in student assessment and increasingly in the performance assessment of other sectors (Davidson, 2005). While risk-based maturity models have been used for safety prioritisation (Westrum, 1993; Hudson, 2007; DRET, 2008; Hancock, 2010) and evaluation of organisational development (Esteves et al, 2010), this paper is the first to adapt maturity models for the evaluation of abandoned mine rehabilitation programs in Australia.In this paper, we used indicators based on the national policy for abandoned mines to assess the maturity of abandoned mine programs. Fourteen elements of maturity were identified (Unger et al, 2012) under the five chapters of the national policy for abandoned mines (MCMPR and MCA, 2010). Jurisdictions were then evaluated and ranked on their maturity on the basis of information that was web-accessible. Information transparency of abandoned mines policies and programs is in itself one element of the maturity chart. Each jurisdiction in Australia was compared with one another and with a Canadian jurisdiction; the British Columbia (BC) Crown Contaminated Sites Program (CCSP), which represents leading practice (Unger, 2009; Unger et al, 2012).Our research found that in some jurisdictions in Australia there is little or no information on abandoned mine programs or individual abandoned mine sites on government websites, while other jurisdictions provided very detailed program information on planning, funding and implementation. Each jurisdiction in Australia, for which web-based information was available, had some elements where they were more mature than other Australian jurisdictions. For some elements, maturity ranked equivalent to the BC CCSP, but most Australian jurisdictions were less mature. There was only one element where a single Australian jurisdiction ranked higher than the BC program in maturity. Legacy mine policies, programs, priorities and funding information via departmental websites are easier to find in some jurisdictions, indicating progression toward greater transparency and more mature programs. A systematic approach to monitoring and evaluating abandoned mines programs is essential for accountability as it can demonstrate liability reduction over time and continual improvement. The maturity model approach can provide both a measure of progress over time as well as a tool to support the implementation of the national policy for abandoned mines (MCMPR and MCA, 2010).CITATION:Unger, C J, Lechner, A M, Walton, A, Glenn, V, Edraki, M and Mulligan, D R, 2014. Maturity of jurisdictional abandoned mine programs in Australia based on web-accessible information, in Proceedings Life-of-Mine 2014 , pp 467–480 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By N Weerasekara, M Powell, P Toor

The effect of liner wear on SAG mill performance has gained much attention in recent years. It is commonly observed that the three key performance criteria of SAG milling; throughput, power and product size all improve as the liner wears.The increase in throughput is generally ascribed to the increase in the grate apertures and the increase in mill volume due to the wear of these components. Whilst the decrease in product size is attributed to the reduction in lifter height and angle, resulting in more breakage by means of attrition and abrasion.Though it is widely acknowledged that the wearing of liner components such as Lifters, Plates and Grates have a significant impact on mill performance, their individual contribution to changes in mill performance has been unclear, and resultantly lead to questions like; what percentage of the throughput increase can be attributed to the increase in mill volume (plate wear)? and how much can be attributed to the increase in grate aperture (grate wear)?It has been found that through the use of grinding surveys, analysis of production data and JKSimMet it was possible to separate the effects of changing liner profile, increasing mill diameter and increasing grate aperture on the mill performance allowing for the quantification of each.The outlined methodology allows for both troubleshooting of problem liner components which reduce milling efficiency in their wear life as well as providing a basis for a more quantitative approach to liner design and reline scheduling.CITATION:Toor, P, Powell, M, Hilden, M and Weerasekara, N, 2015. Understanding the effects of liner wear on semi-autogenous grinding mill performance, in Proceedings MetPlant 2015, pp 150–161 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

Some crystal chemical properties of several apatites from Brazilian deposits and occurrences were determined; the samples had different origins (igneous, metamorphic and sedimentary). The aim was to establish relationships to their froth flotabilities behaviour. Detailed X-ray diffraction studies were carried out, to determine precisely the unit cell parameters and the degrees of crystallinity of the apatite samples. A thorough chemical analysis of these minerals was also conducted. Microflotation studies were carried out, using sodium oleate and dodecylammonium chloride as collectors. The crystallinity levels were determined for all samples studied, with the establishment of a crystallinity index, which varied from 10.0 to 4.5, on a normalised scale. A marked dependence was observed between this crystallinity sequence and flotability; for both collectors, flotability dropped drastically for crystallinity indices lower than 8.0. Also, the low crystallinity apatites showed a decrease in floatability, for longer conditioning times.

Jan 1, 1993

By Gerasimenko MP

The authors consider the features and advantages of a new promising trend in mineral processing - column flotation. Design aerohydrodynamic and process characteristics of pilot-scale columns are studied. Optimum process parameters for various ores and operations are studied. Flow patterns in cells of various cross-sections are investigated and the relationship between Peclet criterion and specific capacity of cell is determined. On this basis options were developed for optimisation of hydrodynamic characteristics of large capacity cells, including longitudinal sectionalising of the collection zone. It is shown that advantages of high column cells (10 - 13 m) produced in the West can be implemented in a sectionalised machine of smaller height (5 - 6 m). Investigations on the influence of slurry and air bubbles flow patterns indicated that to increase flotation rate of particles of various flotabilities it is expedient to combine co- and counter-current flows of phases in a single column. The proposed designs allow tailings to repeatedly return tailings to the collection zone and alternate co- and counter-current slurry and air flows. For the first time columns with alternating slurry flows (combination of co- and counter-current flows) are developed and commercialised. Unique multi-sectional cells having a number of essential advantages compared to monocells are developed. Design features of the cell allow: implementation of different flotation process flowsheets in a single unit, improved beneficiation process results, reduced specific power requirement, and elimination of sludging of the aerator and cell bottom part. Operational problems restricting introduction of column cells are connected with the aeration unit. The new cells are supplied with pneumohydraulic and stepped airlift spargers, allowing control of bubble size distribution with a service life of not less than three years. Successful operation of the new generation of columns with cell volumes of 15, 25, 40, and 80 cu m and the height of 5 - 6 m in copper, molybdenum, antimony, tungsten and nickel ores and coal slurry processing at different plants in this country illustrated their considerable process and operational advantages and verified the proposed options and relationships. A simulation technique of the flotation process and models for the solution of various problems are developed. A modular model of column flotation is constructed taking into account the kinetic relationship of the process and the hydrodynamic regime in the cell. Based on this, a technique of calculating the column parameters based on laboratory tests is developed (scaling-up), and applied for calculating the design of commercial-scale columns is developed.

Jan 1, 1993

Perception has the unfortunate habit of becoming reality. Urban inhabitants unfortunately do not regard mining as a legitimate or desirable business, despite its contribution to Australia's export income (+A $8,000 million, being nearly a third of all exports); share of GDP (it is 4.5%); and the fact that its presence fills up all the empty spaces northwest of the Adelaide-Melbourne-Sydney-Brisbane crescent of inhabitation. The huge economic contribution of Australia's minerals industry, resulting from providing more than half of merchandise exports (Figure 1), is achieved by employing only some 2% of the national work force (Gaulton, 1997). Unfortunately, the minerals industry's critics generally oppose exploration on the basis that what you don't know will not hurt you. It is the 'do-not-confuse-me-with-facts' philosophy or 'ostrich syndrome', which somehow crudely assumes that mining practices have stayed in the style popular circa late 1800s. Somehow ignorance really is bliss for these idealistic believers, who are reminiscent of the members of the Flat Earth Society!

Jan 1, 1997

Statistics on the imports of industrial minerals into the EECshow that the traded volume in 1987 is approximately 23 million tonnes.The following table documents the imported quantities on the most important industrial minerals.

Jan 1, 1989

The early development patterns of both Australia and New Zealand were substantially in parallel and both were heavily indebted to gold mining for, providing the stimulus to growth. However, since the mining boom, of 1895 - 1899, the mining sector in New Zealand has progressively declined, while in Australia it has assumed an increasing importance in the economy. The continued dominance of minerals in Australian trade, and the fact that eight out of the top ten companies in Australia are directly involved in mineral exploration and production, has strongly influenced government and public attitude's to the minerals sector. Although the legal framework of mining and exploration Acts and Regulations are similar it is in, the method of administration, particularly in regard to exploration and prospecting licences, that the gulf across, the Tasman is apparent. Despite the relative ease of application and granting of licences in Australia, in the more settled south eastern part of the continent we are finding more and more land is being zoned unavailable for exploration. In the remote areas, the Aboriginals now control nearly ten per cent of the land area of Australia, virtually with drawing that portion from exploration. The concept of 'Australianisation' has softened a hardening attitude against foreign investment in mining on the part of the bureaucracy. This anti-mining attitude is fortunately, not shared by the public, and we can but hope that the will of the Australian people can filter through to our masters in Canberra, and ease the rapid increase in the number of regulatory bodies which does so much to inhibit the normal conduct of business. The delays caused by interminable hearings and committee investigations all cost money. This cost can only rebound back on the end consumer, who after all is a voter.

Jan 1, 1982

By C J. N Wilson

The central Taupo Volcanic Zone is a region of intense Quaternary silicic volcanism accompanying rapid crustal extension. Modem central TVZ is the most frequently active and productive silicic volcanic system on Earth, erupting rhyolite at c.0.28 m3 s-1. The rhyolites show no major compositional changes with time, but the total extent of magma chamber zonation has changed with the advent of rifting and crustal extension at c.0.7 Ma. At least 34 caldera-forming ignimbrite eruptions have formed a complex sequence of relatively short-lived, nested and/or overlapping volcanic centres in central TVZ. Taupo contrasts with other large silicic magmatic systems in the exceptionally high frequency, but small size, of caldera forming eruptions. This contrast reflects the thin, rifted nature of the TVZ crust that precludes the development of long term magmatic cycles at Taupo. Within central TVZ, non-rhyolitic compositions have been erupted apparently irregularly in time and space; in particular there is no evidence for a geographic separation of basalts from andesites. TVZ is a rifted arc, but its segmented nature, high thermal flux and voluminous rhyolitic volcanism make it unique on Earth.

Jan 1, 1995

By M Quinteiro, Å Sundqvist

What is special about being a female mine manager? We do not believe that the challenge is greater for women in managing a mine compared to managerial positions in other male-dominated businesses. The challenge lies in the fact that it is a male-dominated business. Being a leader belonging to a minority creates a situation where competence not only lies in having technical knowledge or general leadership characteristics, but also in acquiring an understanding of the male norm and being able to behave and communicate effectively in the organisation.In order to move towards a better gender balance at senior levels it is important to set measurable objectives on desirable proportions between women and men at management levels within the company. Focus and action are required to achieve this goal. At LKAB, the current target is to reach 25 per cent women in the total workforce by 2020. To date, LKAB has reached 19.4 per cent women in the total workforce, and the number of women in management positions is 19.9 per cent.It is of vital importance to create a non-discriminating working environment to achieve equal opportunities at the workplace, to be able to use the whole workforce as a resource for recruitment of professionals and managers, thereby improving decision-making, productivity, efficiency and profitability.Women as mine managers is not a utopia, but rather an effect of long-term investments in actions that result in equal opportunities for all employees.CITATION:Quinteiro, M and Sundqvist, Å, 2016. Women as mine managers – a utopia?, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016) , pp 43–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By D M. Frantois-Bongarton

Variograms can be powerful tools for the analysis and control of process streams and their sampling. Their uses and proper utilisation have been described somewhat unclearly to date, and their limitations and precautions of use are too rarely mentioned. The general meaning and properties of the variogram tool and its use in geostatistics are therefore reviewed in details to derive a critical view of its proper use for process control: what to expect from it and what it cannot deliver and which uses are illusory or potentially misleading. A summary of GyÆs seminal work accompanies this essay to put the concepts into historical perspective.CITATION:Frantois-Bongarton, D M, 2012. Review of variogram properties and remarks on its use in process control, in Proceedings Sampling 2012 , pp 175-180 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By R Crookes

Mine to Mill optimisation is not a recently developed concept. It is one which is finally gaining greater acceptance in the Australian Mining Industry, possibly as a consequence of the downturn in markets and certainly made possible by the development of tools and techniques to measure and predict performance of mining equipment and milling plants. Fragment size after blasting has a major bearing on the performance of all aspects of mining and a major influence on the economics of the mine and mill. The process to optimise fragmentation consists of identifying the key factors, measuring their sensitivity through a modelling and trialing program and conducting economic evaluations on the changes on both the mine and mill. Management of the Ernest Henry copper-gold mine in NorthernQueensland, Australia, has espoused the Mine-to-Mill concept and isactively pursuing excellence in blasting to drive down the total cost of mining. Ernest Henry has extremely hard, wet and heavily jointed geological conditions, and had high powder factors and a large percentage of oversize material reporting to the crusher or ROMstockpile. A blasting improvement program was undertaken betweenErnest Henry Mining, Thiess Contractors and Orica Explosives tooptimise the ore size distribution, particularly the oversize component, as a step to reducing production costs. Measures of success included bringing the rock breaker back from double shifts to part-time operation and increasing direct dumping into the crusher from 70 per cent to 92 per cent. Tools and technologies to predict and measure the performance ofindividual blasts are needed before it is possible to optimisefragmentation or the downstream processes. These include suchspecialised Orica Explosives tools as SABREX, POWERSIEVE, andPOWERLINE and commercially available drill monitors. As importantare the more common still and video camera, borehole loggers,measuring tapes, surveying equipment such as face profilers, and ahigh-speed camera if possible. There are many tools which can be applied however it is rarely necessary or possible to use all of them due to time constraints and a point of diminishing returns. The critical point is knowing what the true parameters of the blast were compared to design - only then can the predictive tools be effectively utilised. Stage one of the program has seen gradual improvement as theunderstanding grew and practices have been implemented resulting inreduced bridging in the crusher, geological mapping with respective blast designs and the oversize component under control. This paper is about a process approach which links tools and technology to understand the fragmentation drivers and then to optimising the size distribution.The continuous improvement program continues...

Jan 1, 2000

The phosphorus content of the banded iron formation (BIF) and of the associated iron ore deposits in the north west of Western Australia is known to vary widely, a fact which has considerable econ~mic significance. Trendall and Blockley (1970) have described the variety of textural appearances of apatite in the Hamersley Group BlF, and suggest that apatite may account for the entire phosphorus content of the unaltered BIF.A preliminary investigation using an M.A.C. electron microprobe analyser has shown that, at least in some iron ores and in partially enriched BIF and associated shales, the phosphorus occurrence is more complicated than this. A suite of samples was examined from one location which covered the entire Dales Gorge Member and some adjoining macrobands in the Mt. McRae shale, together with samples selected for their high phosphorus content, degree of ore enrichment, and position relative to the enrichment zone. Calcium apatite was not observed in any sample of ore from this sequence, despite its ubiquitous occurrence in the BIF. Silicate mineralogy in the enriched regions also differs from that in the BIF, but this change has not yet been studied in detail.The phosphorus content of goethite in one orebody is often high and appears to be in solid solution in the goethite structure. It shows little or no variability on a micro-scale within a grain, except where theremay be a zoned enrichment near boundaries and solution channels. There is also a limited solubility of phosphorus in hematite (the maximum observed by the author is 0·1 per cent P); but where the hematite is martitic (after magnetite) its phosphorus content is always low or zero. In some bands, martitic hematite has been hydrated to goethite, and this also has a very low phosphorus content. Phosphorus was not found in the silica or silicates in the ore, and even when iron enrichment is just beginning, a limited suite of samples from the BIF suggests that the phosphorus content of the chert microbands is almost entirely in the microscopic goethite nuclei (after riebeckite) scattered throughout the chert. The ability of goethite and hematite to accept phosphorus...

Jan 1, 1973

On the Kinetics and Equilibrium Models for Biosorption of Ni(II) onto a Gram-Positive Bacteria Strain, Rhodococcus opacus, for Environmental Applications The aim of this fundamental study was to evaluate the biosorption of Ni(II) from aqueous solution streams onto a Rhodococcus opacus strain through kinetics and equilibrium isotherms studies. The biosorption of nickel achieved its highest value in a pH around 5. The experimental data evaluation was carried out focusing three two-parameter models, as: Langmuir, Freundlich, Dubinin - Radushkevich. In order to determine the best isotherm fit, three error analysis methods were used to assess the data: correlation coefficient (R2), residual root mean square error (RMSE) and Chi-square test. The error analysis established that the Freundlich model fits better the nickel biosorption data. Maximum uptake capacity of nickel reached a value around 7.63 mg.g-1 for R. opacus. The biosorption rate was fast and achieved a removal of around 79 per cent of Ni(II) in the first 5 minutes at room temperature (25 ¦ 2¦C). The experimental kinetics data was evaluated considering two models (pseudo-second order and pseudo-first order). The error analysis established that the pseudo-second order model better fits the data.

Sep 13, 2010

The Khanong supergene-enriched copper resource, (~23 Mt at 3.0 per cent Cu), is one of several resources recently discovered in the intrusive-centred, sediment-hosted Au-Cu Sepon mineral field located in southern Lao PDR. The unusual style of hypogene mineralisation and unique set of conditions have resulted in the development and preservation of a supergene-enriched profile in this subtropical climate. Hypogene sulphide-rich mineralisation replaced calcareous cataclastite (fault rock) developed in the flat-lying, extensional, Khanong Fault. Spatially, the hypogene mineralisation was immediately out board of the skarn û hornfels Cu-Bi front and in board of sediment hosted Au-(As-Sb) mineralisation in a zoned intrusive-centred hydrothermal system. In situ supergene enrichment of the sulphide protore has resulted in a high-grade chalcocite-clay zone (~10.3 Mt at 4.6 per cent Cu) overlain by leached limonite-clay. A very high-grade in situ to exotic limonite-clay Cu-oxide-mineral zone is locally developed above impermeable dolomite at the base of chalcocite-clay zone. Exotic Cu-Mn-wad mineralisation developed for up to 1 km down the hydraulic gradient from the chalcocite-clay zone. Unique supergene enrichment conditions have resulted in the high-grade Khanong Cu resource in a subtropical weathering environment. The base of the currently active supergene profile coincides with the base of a flat-lying, pyrite-rich fault rock, dipping parallel to the hill slope, maximising Cu enrichment. Meteoric water has been channelled along subvertical faults and narrow horizontal subsurface zones. Low permeability of the fault host rock and footwall rocks has controlled the low volume and slow movement of groundwater required for supergene enrichment. Erosion has been slowed by the resistive ironstone and limonite-clay layer at surface, which assists in preserving the gentle slope over the chalcocite-clay zone.

Jan 1, 1999

By Lavers G

Factors governing the dissolution of nickel and iron in pentlandite and pyrrhotite concentrates from Mt. Windarra were studied for aqueous solutions at normal temperatures and pressures. The effects of dissolved dioxygen, carbon dioxide, hydrogen ions, and chloride ions are described. The direct reaction of aerated water wiili pyrrhotite is much faster than with pentlandite, and reaction rates are proportional to the dissolved dioxygen concentration. In both cases divalent metal sulphates are produced initially. The subsequent oxidation of iron(II) to iron(III) and its oxolation produces acid solutions which rapidly attack both minerals. The presence of carbon dioxide or chloride ion has little effect on these rates.

Jan 1, 1976

By J Addai-Mensah, M Adam, W Skinner, J Begelhole, K Quast

Granulation of iron ore fines into robust granules is critical to successful sintering and blast furnace operations in iron and steelmaking. Iron and steelmakers desire iron ore granules with high strength, uniform size distribution and low fuel consumption to enhance efficient sintering operation. Unlike hematite ore, magnetite concentrates do not granulate easily at low binder dosage to yield coarser granules due to the absence of nucleus particles. This motivates the present study to harness the complementary properties of hematite ore to enhance granulation of magnetite concentrates via blending. The current state-of-the-art in hematite and magnetite blend granulation is reviewed, along with granule property limitations. Preliminary experimental work on granulation of hematite and magnetite blends as a precursor to sintering is reported.CITATION:Adam, M, Addai-Mensah, J, Begelhole, J, Quast, K and Skinner, W, 2017. Enhancing magnetite concentrate granulation by blending with hematite ore, in Proceedings Iron Ore 2017, pp 17–24 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

THE following brief paper is submitted with a view to encouraging the exploitation of hitherto neglected 10w~ grade ore-bodies which are suitable for extraction by open-cut methods.The Corinthian North mine, situated 10 miles from Southern Cross, in the Yilgarn district of Western Australia, furnishes an example of low working costs, although operations are carried out on quite a limited scale.The body of quartz which is now being worked strikes N.W. and S.E., has a very slight underlie to the west, and lies between bodies of quartz-hrematite s,chist on the east and amphibolite on the west.So far as the property has been explored, it would appear that the underlying sulphide rises to within about 70 ft. of the surface in the northern end of the workings, and pitches away to the south at a grade...

Jan 1, 1915

The subject which I have chosen for my paper is one that I am sure has occurred to the minds of nearly every mining man on these goldfields at some time or other. I refer to the carrying out of hydraulic mining on a fairly large scale on some ofthe alluvial areas of the West Australian goldfields. There are many, no doubt, who have the question ready at the present moment, "But where is the water coming from? " However, the great difficulties in the way are not due to the want of natural facilities, but due to the fact that sufficiently large areas cannot be leased for this purpose under the present Mining Act. Now, ever since the inception of the West Australian goldfields there has been the old familiar cry when referring to some alluvial gully or flat, "I wish I had a head of water to sluice that ground," but what seems an impossibility at times can be brought to a very great possibility by the use of a little thought and the expenditure of the necessary capital. This is so as regards West Australia with sluicing which, in spite of the its having so many detractors, can be carried out successfully in certain localities if the ordinary facilities on the part of the Govenment are given, and on the other hand the necessary capital is supplied. Alluvial gold areas, I propose now to draw your attention to first of all, the numerous alluvial areas that exist around Coolgardie, Kalgoorlie, Bulong, Kurnalpi and many other centres. Some of these areas have afforded fortunes inthe early days to the alluvial miner, and also afforded a living for years to many diggers' by the use of the dryblowing...

Jan 1, 1901