Search Documents

By Otto Wartenweiler

AFTER the phenomenal development of the new mine, the United Eastern Mining Co., with Mr. Frank A. Keith as President, decided to install a reduction plant. The character of the ore, closely resembling the product of other mines in the district, did not offer any particular metallurgical problems, since these neighboring mines had been operating milling plants very successfully for several years. Thus, with the general metallurgical treatment fairly well-defined, the matter of next importance was to design and construct a plant as economically as possible, that would give the best results obtainable. The ore consists of a mixture of calcite and quartz in about equal quantities with some decomposed andesite, while the average value of mill heads were calculated to be $20 plus in gold, no silver being present. The tonnage to be treated at ,the start was fixed at 200 tons, but, in view of the favorable condition of the mine, it was considered advisable to arrange facilities, for increasing the capacity to 400 tons. . While it is best in some cases to adopt a distinct independent unit system where future enlargement is contemplated, in this instance the plans worked out differently. Summarized, the treatment adopted consists of coarse crushing, coarse grinding, fine grinding and cyanidation. For coarse crushing the selection of the No. 6 size gyratory crusher was governed not so much by its capacity as by the size of the feed openings to properly receive the run-of-mine material, which was too coarse for a No. 5 crusher. To accomplish the coarse grinding to. best advantage, a careful comparison was made between the modern steel ball mill-the last word in crushing and grinding-and one of its older, and, at that time better-established, competitors, the rolls.' The following conclusion was reached: While it is possible that for the sized plant under consideration the cost of operating rolls might be a little cheaper, it is preferable to use ball mills because a simpler arrangement is possible, and1 because. the handling of, ball mills is preferred by the operator.

Jan 11, 1917

By W. H. Bassett

THE ease and value of the application of spectrum analysis to industrial chemistry appears to be appreciated in few of the large works laboratories of this country. For 8 years, this analysis has been of great value to the authors in both analytical and metallurgical work. To the analyst the complete qualitative analysis of an unknown alloy, revealed by a spectrogram, is a sure basis for the planning of the most direct and rapid method of attack. As the determination of each element proceeds, the purity of precipitates may be checked as often as desired. The spectrograph proves invaluable in the recognition of impurities, the separation of which would entail a lengthy and difficult procedure, or when the weight of an unknown is less than is necessary to complete the desired determinations. A few hundredths of a gram will usually suffice for spectrographic analysis. In the separation of the rarer elements, the spectrograph will show, with precision, the point where each step has been successful. In zinc of certain classes, indium, gallium, and germanium have been isolated in this way; the presence of antimony in lake coppers has been proved; and bismuth has been detected in zinc and in alloys where the presence of a few thousandths of a per cent. would be harmful. An antimony precipitate in a delicate determination may contain a considerable proportion of tin or arsenic, both of which will be revealed. The spectrograph is consequently important to the metallurgist as well as to the analyst.

Jan 2, 1922

By Dean S. Rogers

The conventional role of exploration, development and grade control is examined in this paper within the context of the many and varied types of gold occurrences which are found at the Dome Mine. The account endeavours to trace the development of the total ore evaluation process, from diamond drilling through the exploration and drifting stage, to the stope development and planning phase of the operation, with an emphasis on sampling techniques and assaying procedure. The concept of ore reserve calculations is developed and the practice of grade control is described. In summary, the role of the geological, the engineering and the mining department is presented in relation to the contribution each has to make in the evaluation and exploitation of ore from one of the world's classic Archean gold deposits.

Jan 1, 1985

By Roger C. Malan

The Monument Valley and White Canyon districts are in northeastern Arizona and southeastern Utah. Exploration and mining for uranium has been conducted in these districts since the late 1940's. In July 1965, ore reserves plus ore production at 174 properties were approximately 3.3 million tons of ore containing about 19 million pounds U3O8, of which about 10 per cent remained in reserves. The two largest mines, Monument No. 2 and Happy Jack, together account for about 45 per cent of the sum of production and reserves. Approximately half the deposits in these districts contain less than 1000 tons of ore. Nearly 5000 feet of Permian, Triassic, and Jurassic sedimentary rocks, mainly continental in origin, are exposed in these districts. All the important uranium deposits are in the Shinarump, the basal member of the Chinle Formation of Triassic age. The Shinarump lies on a widespread unconformity. It is composed of fluvial sediments, generally less than 100 feet thick, that were deposited by streams flowing from a source to the south. Most of the deposits are in an arcuate belt, convex to the west. This belt, 3 to 12 miles wide, extends from Monument Valley northward nearly 130 miles. It is along the western flank of the ancient Monument Valley-Monticello upland, an area that was slightly uplifted at the beginning and again at the end of deposition of the Shinarump. Erosion and subsequent reworking of the Shinarump sediments in the vicinity of this upland are postulated to have made possible the transportation, in solution, of the uranium contained in these sediments. The soluble uranium probably was carried by migrating ground water into sites favorable for precipitation in Shinarump beds bordering the upland. Thus, the original very small amounts of dispersed uranium in the early Shinarump sediments were accreted in the favorable belt where the accumulations of carbonaceous plant remains and their decay products provided a persistent reducing environment.

Jan 1, 1968

By H. S. Martin

The Phosphate Recovery Corporation operates three flotation plants, Nos. 1 and 2 concentrators about three miles northeast of Mulberry, Florida, and No. 3 plant at Wales, Tennessee. These plants represent the first commercial phosphate flotation operation and are also believed to be the largest nonmetallic flotation operation in the world at the present time. The details of this paper will be confined to plant No. 2, this being the newest and largest concentrator in Florida, and the flow sheet being practically the same as at plant No. 1. The No. 3 plant has been operated but a short time and has been shut down since December, 1932, on account of the decrease in phosphate rock production. The phosphate washers usually are located centrally on a known deposit so that about two hundred acres of ground can be mined economically to each washer location. The washers are moved to new areas when the distance becomes too great for economical pumping. The flotation plants are built either adjacent to a washer, so that current debris may be utilized, or on the site of a former washer where there is sufficient accumulated debris available for mining, and the flotation plants must also be moved from time to time. Most of the water used in the Florida flotation plants is recovered after passing through a circulating system where most of the fine suspended matter is settled out, but some make-up water is obtained from deep wells near the plant. Power is obtained from the Tampa Electric Co. through the distribution facilities of the International Agricultural Corporation. Flotation concentrate is hauled from the plant by trolley over the International Agricultural Corporation's trolley system, to the drying plant at Prairie, one mile northwest of Mulberry. Ore Treated In the pebble phosphate district of Florida, the phosphate mineral, or collophane, is usually found in horizontal beds of varying thickness

Jan 1, 1935

By M. R. J. Wyllie, Michael A. Torcaso

With the continued deep drilling of today, increasing numbers of high pressure and high temperature gas-condensate reservoirs are being discovered. Correspondingly, the ranges of properties of gas-condensate reservoir fluids are also being increased. The literature1*'." contains several excellent reviews of the property ranges in presently known condensate reservoirs. When one examines these property ranges, it becomes apparent that the need for reliable data is great if the engineer is to evaluate properly or appraise a gas-condensate reservoir. It is the purpose of this paper to present phase-behavior data that will point out some of the important variables that influence recovery from gas-condensate reservoirs produced by pressure depletion. All these variables may be resolved into two major categories: the hydroc:arbon composition of the reservoir fluid and the physical properties of the reservoir. But the variables which we will consider are those which are usually determined from well tests shortly after discovery and are, consequently, readily available to the engineer. They are as follows: (1) the producing separator gas-stock-tank liquid ratio, (2) stock-tank liquid gravity, and (3) reservoir temperature. Laboratory depletion studies have been performed on several reservoir fluids to illustrate the effect of changes in the cronsidered variables upon ultimate recoveries. The deviation factors, Z, of a series of reservoir fluids were determined experimentally to illustrate their order of magnitude and their effect upon the calculation of in-place reserves existing at high pressurcs and temperatures. The procedures followed in conjunction with the performance of these studies and their associated calculations are illustrated in Fig. 1. For the purpose of this paper, the depletion recoveries are expressed only in terms of pcr cent of initial stock-tank liquid, with the abandonment pressure assumed to be 500 psig. VARIATION OF RECOVERY WITH INITIAL PRODUCING SEPARATOR GAS-STOCK-TANK LIQUID RATIO The producing separator gas-stock-tank liquid ratio has long been one of the principal criteria in assumptions and generalized correlations' used for the estimation of ultimate recovery from gas-condensate reservoirs. Fig. 2 presents a plot of the cumulative recovery of stock-tank liquid at abandonment as a function of the initial producing separator gas-stock-tank liquid ratio. The graphical illustration represents the results of 44 laboratory depletion studies performed on actual gas-condensate fluids. These data are presented not only to illustrate the general trend of ultimate recovery increase with initial producing ratio increase but to emphasize the considerable variation in possible recovery at any given producing ratio. Table 1 presents the properties of two actual reservoir fluids chosen to illustrate the approximate extremities of producing ratios for gas-condensate systems. The fluids designated as A and B exhibited initial producing ratios of 3,400 and 114,000 scf/bbl, respectively. Fig. 3 presents a graphical comparison of the cumulative stock-tank liquid recoveries, calculated from the well-stream compositions and produced volumes for each fluid during depletion. It is to be noted that Fluid A exhibited a recovery of only 16.5 per cent when produced to an assumed abandonment pressure of 500 psig while the corresponding recovery for Fluid B was calculated to be 62.2 per cent. This difference in recovery, which exemplifies the general trend of recovery increase with initial producing ratio increase, is readily explained by consid-

By W. M. Gray

The determination of the state of stress existing at a point in any solid body requires the determination of the six components of the stress tensor relative to a convenient set of axes. One general method of doing this in rock is to make strain or deformation measurements associated with local relief of stress in a number of boreholes penetrating a limited volume in the vicinity of the point at which the stress is to be determined. The stress is assumed to be constant throughout this volume. Leeman1 has described a number of the instruments that have been developed for making deformation or strain measurements in boreholes. Panek2 has described the application of statistical methods to the determination of the average components of ground stress from sets of measurements made in boreholes by means of deformation meters of the type developed by the U.S. Bureau of Mines. In this paper attention is given initially to the strain cell developed for use on the flattened ends of boreholes by the Council for Scientific and Industrial Research (CSIR) , South Africa. The equations required for evaluating the average components of ground stress from measurements made by means of the CSIR strain cell are derived. These equations are similar in form to those applying to measurements made by the borehole deformation meter developed by the U.S. Bureau of Mines. The results of an investigation of the properties of the equations are described. These results are important in the practical use of both the instruments mentioned above and any instrument based on similar principles.

Jan 1, 1968

By R. G. Fleck, W. R. Webb

Iron ore mining in the Adirondack region of northern New York dates back to the Revolutionary War. It is recorded that Benedict Arnold in his campaigns in the Lake Champlain area during the American Revolution utilized the local ores to produce armament and cannon balls. Through the efforts of early pioneers, the iron mining industry in northern New York gained impetus so that in the 1880's mines in the area accounted for nearly one fourth of the iron ore produced in the United States. Both magnetite and red hematite ores were mined during this period. With the discovery of the Lake Superior ores, the iron ore industry in New York started to decline and remained relatively unimportant until 1938. Modern day methods of mining and beneficiating sufficiently high tonnages of low-grade ores to justify the large expenditures for plant and equipment prompted a resurgence in northern New York mining. During the past several years, the production of iron ore from the Adirondack magnetites has greatly increased, and production which amounted to .6%, of the United States total during the 1918-1928 period (Mining and Metallurgy, November 1943) has been increased to 2.85% of the total in 1948. Today, Republic Steel is mining in the Port Henry-Mineville and Lyon Mountain areas; the

Jan 4, 1950

By Hal T. Morris

The main Tintic mining district in central Utah has produced approximately 13,500,000 tons of ore, containing silver, lead, gold, copper, zinc, and other metals, valued at more than $315,000,000. More than 90 per cent of this ore has come from large, irregular ore bodies that have replaced folded and faulted limestone and dolomite strata. Of lesser importance are replacement veins that chiefly cut contact-pyrometasomatized carbonate rocks and fissure veins that cut altered intrμsive bodies and volcanic rocks. The district is in the west-central part of the East Tintic Mountains, a north-trending fault-block range near the eastern margin of the Great Basin. The consolidated sedimentary rocks exposed at the surface and in mine workings are miogeosynclinal deposits more than 10,000 feet thick that range in age from late Precambrian to Late Mississippian. They are folded and strongly faulted and are partly overlain by volcanic tuffs and agglomerates and by extensive flows of porphyritic and vitrophyric quartz latite, latite, and trachyandesite of Eocene age. All of these rocks are locally concealed beneath thick alluvial deposits of Pliocene and Quaternary age. The Eocene and older rocks are cut by dikes, sills, and small stocks of porphyritic quartz monzonite, monzonite, and latite, which are genetically related to the ore deposits. The district is inactive except for the production of halloysite clay and for minor leasing activity and exploration ventures. Several exploration targets remain untested.

Jan 1, 1968

By Maurice E. Peloubet

This discussion of accounting will describe the statements and the information that the accounting system produces, from the point of view of those who use such systems rather than of those who prepare them and who do the detail and technical accounting work. In any well organized mine, quarry, or other enterprise exploiting a mineral deposit, no matter how small, some clerical and accounting work must be done. Miners and other employes must be paid, supplies must be purchased and issued, and various tax and information returns, which even the smallest enterprise must file, have to be prepared. In this chapter it is assumed that the enterprise has employes of this type and that they understand the fundamentals of record keeping and accounting. It would be impossible here to give sufficiently full explanations to enable a man with no previous clerical and accounting training to set up and operate an accounting and cost system for even the simplest extractive operation. Rather, we shall hope first, to tell the investor and the operator, from the chief engineer or president down to a subforeman, what to expect from the accounting statements and records and how to use this information in his daily work; and second, that it will enable the man with some knowledge of accounting or book- keeping, but with little or no experience in any extractive industry, to set up and operate a satisfactory system for a mine or other extractive enterprise. For readers who wish to go further, the bibliography at the end of this chapter contains many references. T he emphasis has, therefore, been placed on the statements to be produced and the purposes for which they are to be used rather than the underlying books and records. These are, with a few exceptions which will be described later, essentially what might be found in any industrial enterprise and would probably, in the extremely small enterprise, consist of handwritten journals, ledgers, analysis books, payroll books, and stores ledgers. In the larger enterprise, various types of mechanical accounting would be introduced in proportion to the complexity of the operation.

Jan 1, 1964

By R. E. Hummel, J. W. Koger

IT is generally accepted that the martensitic start temperature (Ms) can be determined by resistivity measurements and is that temperature where the resistivity vs temperature curve on cooling first deviates from a straight line.1-4 Both Titchener and ever' and pops5 have used resistivity measurements to follow the martensitic transformation in b1 Cu-Zn and ternary Cu-Zn-based b-phase alloys, respectively. Actually because of the nature of their measurements the temperature of minimum resistivity (M) was used by these authors to determine "Ms" . Also, due to experimental difficulties in detecting M, with resistivity measurements, Pops and Massalski 8 determined M, by optical microscopy. The present communication is concerned with high-precision, low-temperature resistivity measurements which reveal a definite M, temperature which differs from the temperature of minimum resistivity (M). It is also shown that M is merely the result of the geometry of the percent-transformation curve and the temperature coefficient of resistivity of the alloy. In other words, it will be demonstrated that M has no apparent significance (except that it denotes a temperature at which some percent of martensite can be detected in a given alloy). Alloy specimens were made by melting 99.999 pct Cu and 99.9999 pct Zn in sealed and evacuated quartz tubes and homogenizing them at 601PC for 300 hr. After the alloy was cold-rolled into foils suitable for resistivity measurements, it was quenched in ice water from 871PC. The chemical analysis showed a zinc content of 38.8 wt pct. The cooling rate during the martensite transformation was 1°C per min and was controlled with a thermistor. Electrical resistivity measurements were made using a K-3 type potentiometer; the reproducibility of the resistivity values was better than 0.03 pct. Temperatures were measured with a thermocouple to an accuracy of better than 0.2° C. Fig. 1 shows the resistivity vs temperature curves of the martensitic transformation in B1 Cu-Zn for both cooling and heating. The starting point of the martensitic transformation (M,) was taken as that

Jan 1, 1968

By William H. Bassett

RECENTLY it has become the custom of retiring presidents to talk of the relations of the Institute to its membership and its constituency- and it seems a good precedent to follow. Past-president Smith reviewed our relations to materials and to society in general. Mr. Bradley spoke of the value and use of our publications and of our educational duties. My message will be in regard to the coordination of our various groups of member interests and of service to industry. This Institute has, within its organization, four divisions and fourteen technical committees--each interested in a separate put very definite subject, and each covering a phase of mining engineering interest. These vary from geology and the geophysical methods of prospecting, to the physics of the structure of metals, truly "from the mine to the consumer"-from the preparation for mining to the final use of that which has been mined.

Jan 1, 1931

By H. P. Stüwe

HE recent papers of Aust and Rutter112 have again brought to mind the importance of certain "special" orientation relationships between the lattices of two fcc crystals on the mobility of the grain boundary separating them. No theoretical treatment of this problem has been offered till now. The only principle published so far that has given an indication why certain orientation relationships should be "special" is the counting of "coincidence sites" according to the suggestions by Kronberg and Wilson.3 The "coincidence plots" published by these authors show, for instance, that two fcc lattices rotated by 38 deg around a common (111)-axis have 1/7 of their lattice sites in common. Such an orientation relationship is also characteristic for high boundary mobility. The accuracy of the orientation relationship needed for high mobility is not too rigid. Deviations up to 10 deg from the ideal orientation seem to be tolerable as can be gathered from the experimental data.'j4 The auestion arises, then. how the density of coincidence sites will be affected by a deviatioi from mathematical accuracy. This can be checked by a simple model. Two sieves are prepared, the arrangement of the holes corresponding to lattice sites on a (111)-plane in a fcc crystal. They are placed upon each other, Fig. 1. One is kept fixed, the other is rotated around an axis pushed through one hole in common to both. The light falling through holes of both sieves is then a measure for the density of coincidence sites. If the diameter of the holes is very small, light intensity is contributed only by holes the centers of which coincide "exactly." If the diameter of the holes is rather large, some intensity will be contributed by

Jan 1, 1962

By H. E. Strauss

The time-to-fracture test has been applied to pure platinum and to two alloys of platinum under the special conditions of small cross-sectional area of the specimens and of a test temperature above the annealing temperature. While the results are similar in character to those secured with large specimens of steel at temperatures below the annealing temperatures, two differences are noted: (I) an upward inflection in the curves for log stress vs. log time for the alloys, and (2) a sharp break in the curve for log stress vs. log time for pure platinum when single crystals filled the wire. The experiments showed that: (I) platinum and 10 per cent rhodium-platinum maintained their strengths at IIOO°C. better than did to per cent iridium-platinum, and (2) the rhodium-platinum after a time exceeded the iridium-platinum in strength at IIOO°C. Platinum alloys in their service at high temperatures encounter conditions somewhat similar to those that exist in the usual form of the "time-to-fracture"l test with steel. This paper is intended primarily to present results obtained by a "time-to-fracture" test under conditions approximating actual service for platinum (at the temperature IIOO°C. under oxidizing conditions) with three materials, pure platinum (99.99 per cent), a platinum alloy with 10 per cent iridium, and a platinum alloy with 10 per cent rhodium. The experimental procedure differed from that previously used in this type of measurement in that the samples were of small diameter (0.010 in.), were fully annealed, and were tested at a temperature definitely above their annealing points (600°C., IOOO°C. and 1050°C., respectively, for 60 per cent cold reduction and 15 min. heating time2,3). The experimental arrangement was similar to that previously described,' using as heating unit a small, horizontal, platinum-wound furnace, ½ by 12 in., maintained at constant temperature by an automatic controller. The samples were 0.010-in. wires, which had been annealed at 1200°C. by drawing them slowly through the furnace. The time-to-fracture was measured electrically. Elongation was not determined because of the difficulties inherent in the experimental arrangement. Life—that is, the time-to-fracture—was considered the important property in these first tests. No attempt was made to measure the reduction in area, but the types of fracture were noted qualitatively; in the text they are referred to as (I) the normal, plastic, or necked fracture, (2) the knife-edge fracture, and (3) the brittle or intercrystalline fratture with small reduction of area. Results for different constant applied stresses are plotted in Fig. I. In all cases at least two trials were made for each stress, although they cannot always be indicated separately on the curves. The breaking Stresses drop very rapidly to a small frat-286

Jan 1, 1943

By H. E. Strauss

The time-to-fracture test has been applied to pure platinum and to two alloys of platinum under the special conditions of small cross-sectional area of the specimens and of a test temperature above the annealing temperature. While the results are similar in character to those secured with large specimens of steel at temperatures below the annealing temperatures, two differences are noted: (I) an upward inflection in the curves for log stress vs. log time for the alloys, and (2) a sharp break in the curve for log stress vs. log time for pure platinum when single crystals filled the wire. The experiments showed that: (I) platinum and 10 per cent rhodium-platinum maintained their strengths at IIOO°C. better than did to per cent iridium-platinum, and (2) the rhodium-platinum after a time exceeded the iridium-platinum in strength at IIOO°C. Platinum alloys in their service at high temperatures encounter conditions somewhat similar to those that exist in the usual form of the "time-to-fracture"l test with steel. This paper is intended primarily to present results obtained by a "time-to-fracture" test under conditions approximating actual service for platinum (at the temperature IIOO°C. under oxidizing conditions) with three materials, pure platinum (99.99 per cent), a platinum alloy with 10 per cent iridium, and a platinum alloy with 10 per cent rhodium. The experimental procedure differed from that previously used in this type of measurement in that the samples were of small diameter (0.010 in.), were fully annealed, and were tested at a temperature definitely above their annealing points (600°C., IOOO°C. and 1050°C., respectively, for 60 per cent cold reduction and 15 min. heating time2,3). The experimental arrangement was similar to that previously described,' using as heating unit a small, horizontal, platinum-wound furnace, ½ by 12 in., maintained at constant temperature by an automatic controller. The samples were 0.010-in. wires, which had been annealed at 1200°C. by drawing them slowly through the furnace. The time-to-fracture was measured electrically. Elongation was not determined because of the difficulties inherent in the experimental arrangement. Life—that is, the time-to-fracture—was considered the important property in these first tests. No attempt was made to measure the reduction in area, but the types of fracture were noted qualitatively; in the text they are referred to as (I) the normal, plastic, or necked fracture, (2) the knife-edge fracture, and (3) the brittle or intercrystalline fratture with small reduction of area. Results for different constant applied stresses are plotted in Fig. I. In all cases at least two trials were made for each stress, although they cannot always be indicated separately on the curves. The breaking Stresses drop very rapidly to a small frat-286

Jan 1, 1943

J. H. HEGINBOTHAM, a, metallurgist of the General Engineering Co., talked on "Current Milling Practice at Kirkland Lake," at the December meeting of the Utah Section. The ore is enough alike through the whole district so that some generalizations and comparisons may be made. The question as to whether or not the flotation process should be used in the flowsheet for extracting gold by cyanide solutions is still being vigorously debated, and it will seemingly need some years for a definite answer to be given. Most of the gold is either free, though much of it is finely dispersed in quartz, or occurs with pyrite. At times there may be 2 per cent of telluride compounds in the ore, but the amount of gold telluride present is small and has not been definitely established. It has been shown by Dr. Haultain and others that though gold tellurides may be so finely disseminated that it is necessary to grind the ore exceedingly fine, the compounds themselves are not difficultly soluble. (An increase in temperature helps to dissolve tellurides, and also to settle pulps.) It is likely that if the ore were ground through 400 mesh, practically all of the gold would be soluble. As it is, with 96 to 98 per cent of the ore ground to minus 200 mesh, and some 70 per cent minus 325, the cost of

Jan 1, 1934

By R. G. Aspden, D. A. Colling

THE {120}(001) texture has been reported in near 50 pct Ni-Fe alloys <0.004 in. thick1,2 and in copper 0.014 in. thick.3 This texture is one of two types of secondary recrystallization textures observed to replace a cube texture matrix and is desirable in Fe-Ni alloys because of its unique magnetic characteristics.1,2 However, the conditions for and mechanism of the {120}(001) formation are not well understood.3 During an investigation of the influence of alloying elements on the magnetic characteristics of 49 pct Ni-Fe alloys with a sheet thickness of 0.014 in., we have observed the growth of {120}(001) secondaries when strong deoxidizers such as aluminum and calcium were present. It is believed that this observation in unique and provides additional insight with regard to the mechanism for {120}(001) texture formation. Three alloys were prepared with electrolytic iron and nickel and contained a nominal 49 wt pct Ni. Alloy A was a straight binary Fe-Ni alloy, whereas intentional additions of 0.013 wt pct Ca to alloy B and of 0.59 wt pct A1 to alloy C were made. Ingots were forged at 1100 C, hot-rolled to 0.150 in. gage, pickled, and cold-rolled to 0.014 in. Standard U-shaped magnetic test specimens were punched, deburred, sprayed with MgO, and annealed in ~50°C dew point hydrogen. Textures were identified with the aid of etch pits, the

Jan 1, 1970

This is a most interesting paper and some data in it are corroborated by work I did at Watertown Arsenal some time ago with iron powder. I would like to ask Dr. Wulff to say just a little more about the compressive and tensile stresses on the surface of compacts. JOHN WULFF (author&apos;s reply).-Our work has not yet been completed; although enough data have been obtained with cylindrical compacts of iron to permit some conclusions. Briefly, in a compact 3/4 in. high and 1/2 in. in diameter pressed at 48 tons per sq. in., the residual stresses on the surface measured by X-ray diffraction techniques are as follows: The radial stresses on top center and bottom of compacts are practically zero; the longitudinal residual stresses on the side walls are near the top quarter of the compact about seven tenths that of the yield point of mild steel in tension; at the center surface of the compact they are in compression and in magnitude about 0.3 that of mild steel in tension; near the bottom, they are practically zero. F. V. LENEL.?- I was particularly interested in the work that Messrs. Wulff and Seelig reported on the influence of lubrication on the density of parts. In connection with the work of the American Society for Testing Materials on determining the green density of a compact, we ran into considerable difficulty in getting reproducible results of green density determinations. It was much easier to get a reproducible green density when the lubricant was mixed with the powder than when the lubricant was applied to the die walls; particularly when the die was not perfect-i.e., if it was somewhat rough or out of round. In this case, it was almost impossible to get reproducible green densities when the die walls were lubricated, while it was not too difficult to get reproducible

Jan 1, 1946

The regular activities of the Institute are financed mainly by income derived from members&apos; dues, from advertising in MINING AND METALLURGY, and from the sale of publications to the public. In addition, collateral activities and special projects are financed each year by means of income from endowed funds controlled and administered by the Institute. In the aggregate, the principal sums of these endowments amount to more than $530,000. An active effort is being made to increase the endowment funds of the Institute through a standing committee, of which H. T. Hamilton is chairman, and of which the other members are: W. H. Aldridge, George D. Barron, Cleveland E. Dodge, D. C. Jackling, Henry Krumb and J. V. W. Reynders. This committee feels that there exists a tremendous opportunity for the Institute to be of ever-growing service to the public, to the mineral industries, and to the profession. It welcomes suggestions as to names of men of means who are vitally interested in the mineral industries, and to whom the opportunity to make a contribution or bequest might appeal favorably if presented in the proper light by the committee.

Jan 1, 1941

By Elmer W. Pehrson

Minerals have played a prominent role in the affairs of man and nations since time immemorial but with the advent of the industrial revolution, expanding use of the products of the mineral kingdom became synonymous with the material progress of mankind. Individuals and business groups have recognized this fact so have been aggressive in searching for and utilizing mineral resources, with notable success. Indeed, their achievements are primarily responsible for the present Machine Age. On the other hand, until recently the body politic has failed to grasp fully the essentiality of minerals although, at times, access to mineral supplies has been an important factor in the political maneuvers of nations. This chapter is concerned primarily with the broader political and economic relationships of mineral resources to the world economy, and with the internal and external actions of nations in the field of minerals. Many factors that condition the mineral economy of regions and the world as a whole, influence the internal and external affairs of individual nations. The more important of these are: 1. The nature of man&apos;s dependence on minerals. 2. The problems resulting from the unique characteristics of mineral occurrence. 3. Geopolitical concepts. 4. Minerals and world power. Actions of individual nations affecting their mineral economy seek two basic objectives : 1. Attainment and maintenance of prosperity. 2. Military security. Other objectives may be cited but on careful analysis they become integral parts or extreme phases of the two points noted above. For example, the twentieth century aggressions of the USSR, Germany, Italy, and Japan might be considered as direct bids for world power but they also can be interpreted as exaggerated or mistaken efforts toward military security and peacetime prosperity. Similarly, trade barriers, nationalization of industries, foreign exchange manipulations, taxation, monopolistic prac-

Jan 1, 1959