Search Documents

By AIME AIME

NAPOLEON'S dictum that an Army travels on its stomach has not changed in this present war, but the things an Army's stomach calls for would be more than strange to Napoleon. Today one of the main articles of diet for the mechanized army is oil and gasoline, and the chief and most efficient source of 'apply overland is the pipe line. It was a flexible 4-in. pipe line that supplied the voracious appetite of tanks, trucks, jeeps, and planes across the North African desert. and it is the 1800-mile pipe line from Calcutta to Kunming, Yunnan Province in China, the longest in the world, that supplied oil and 100-octane gas for the trucks, tanks, Jeeps, and planes fighting on the Assam-Burma-China front in recent months. Completion of this approximately 1800-mile pipe line to China over rivers that had never been bridged, over hill that towered 9000 ft., and over swamps

Jan 1, 1945

By F. V. Lenel

Resistance sintering under pressure is a method of hot pressing in which a powder compact is subjected to pressure and simultaneously heated by passing a low voltage high amperage current through it. Equipment for this process is described. Its basic characteristics such as resistance requirements for powders and compacts, temperature distribution in compacts, and gas reactions during resistance sintering are discussed. Examples of the sintering process in compacts made of a single metal or an alloy powder and in compacts made of mixtures of powders are presented. Potential commercial applications of the process are evaluated. THE usual sequence of operations in commercial powder metallurgy is to compact metal powders in a die at room temperature and sinter the compact subsequently without applying pressure while the compact is in the sintering furnaces. In hot pressing, on the other hand, the compacting and the sintering are combined. The loose powder, or in many cases a cold formed compact, is inserted into the die which is held at the hot pressing temperature, the compact is left in the die until it attains its temperature, and then pressure is applied and maintained for a given length of time. The die may be heated by surrounding it with a suitable furnace, by high frequency induction heating, or by passing current through the die. In hot pressing, compacts of high density and good mechanical properties can be produced in a relatively short time. One of the principal difficulties in hot pressing is the lack of suitable die materials which will have adequate strength at the hot pressing temperature. This difficulty can be overcome at least partially by heating only the material to be hot pressed without heating the die directly. This can be done by passing a low voltage high amperage current through the material and simultaneously subjecting it to pressure. Either loose powders or compacts can be hot pressed by this method in which the desired temperature is produced by the power dissipated in the metal powder. This method of hot pressing has been termed "electrical resistance sintering under pressure." The most significant differences between this operation and conventional hot pressing are: 1—The sintering times are very short, usually a fraction of a second and at most a few seconds. 2—The powder and die are initially cold. 3—Heat is generated within the powder itself and not conducted in from the die. 4— The pressure used is high. 5—Cooling following sintering is rapid, amounting to a quench. Resistance sintering of metal powders under pressure has been suggested repeatedly. In 1933, G. F. Taylor' proposed an apparatus which consisted of an insulating tube made of glass, or a ceramic filled with the powder to be pressed, and plungers above and below the powder. The powder was to be heated by passing an electric current through it and pressure was then applied. The apparatus was intended principally for hot pressing cemented carbides. Although the principle of resistance sintering under pressure is clearly shown in this patent, few details are given. A sintering period of a second or a fraction of a second, which is terminated by the operation of an inertia switch, is mentioned but no values for current density are mentioned. Low pressures, such as atmospheric pressure or a somewhat higher pressure exerted through a lever, are suggested. W. D. Jones' discussed electrical resistance sintering under pressure and proposed using resistance welding apparatus for this purpose. In a patent issued in 1944, G. D. Cremera described a method of electrical resistance sintering under pressure using resistance welding apparatus which was to be applied mostly to nonferrous metals such as copper, brass, bronze, and aluminum. Current densities of 400,000 amp per sq in., sintering times of 1 and 2 cycles of 60 cycle current, and pressures of 5 to 10 tsi are proposed. Cremer suggested using an

Jan 1, 1956

Jan 1, 1959

By R. L. Wilcox, M. L. Fuller

Most commercial alloys undergo changes in phase composition after casting. This is a natural result of the fact that the alloys are not in a state of phase equilibrium as cast and phase changes will therefore take place, with more or less rapidity, in an attempt to attain equilibrium. The practical aspect of aging in zinc-Alloy die castings concerns the changes in physical properties and in dimensions that may accompany aging phase changes. Harmful alterations have been reduced to a minimum and zinc-alloy die castings are being produced today that are so stable with respect to dimensions and physical properties that they are entirely suitable for most practical purposes1. In the first paper2 of this series, and in this paper, aging phase changes of zinc-alloy die castings have been investigated and the possible influence of these changes on dimensional changes of the castings has been evaluated and compared with the dimensional changes actually experienced. The change of dimensions has been selected for practical comparison in these papers because the effect of phase changes on the dimensions of a casting is directly calculable from X-ray crystal-analysis data of the phase structure. The die-casting alloys considered contain, in addition to zinc, 4 per cent of aluminum, about 0.03 per cent magnesium, and from 0 to 3 per cent of copper. It was shown in the former paper that the eutectoidal decomposition of the beta aluminum-zinc phase, while intrinsically capable of causing a considerable shrinkage, can have very little effect on the observed shrinkage of die castings because it takes place within a few days of aging, whereas the observed shrinkage continues for five weeks. It was therefore concluded that the other existing phase change, namely, the segregation of secondary phase from the zinc-base solid solution, must account for the major portion of the shrinkage.

Jan 1, 1936

By AIME AIME

I am happy to welcome you to the twenty-third conference of the National Open-Hearth Committee, and our joint conference with the Blast Furnace Committee, of the American Institute of Mining and Metallurgical Engineers. It is appropriate that, for our fifteenth year anniversary, we should meet in the hotel and the city where this Open-Hearth Committee was inaugurated in 1925. At that first meeting, only a handful of men from a number of steel companies met to discuss ways and means to start a movement to improve the practical and metallurgical technique of open-hearth operations among independent manufacturers, as the United States Steel Corporation had carried on for many years.

Jan 1, 1940

By S. Saito, P. A. Beck

The crystal structure of MoNi3 was determined by means of X-ray diffraction. This structure is isotype with that of ovgered TiCu3. The lattice parameters are: a. = 5.064A, bo = 4.224A, co = 4.448A, and zf 0.157. If the orthorhombic distortion (slight relative to the corresponding orthohexagonal unit cell) is disregarded, the structure may be described in terms of a close-packed ordered atomic layer, stacked in the sequence: abab. The structztres of ordered TiCu3 and TiAl3 are homotectic. The three types of ordered hexagonal phases, iso-structural with TiNi3, MgCd3, and VCo3, are known to occur in AB3 alloys of transition elements of the first, second, ad third long periods. It was noted1 that phases with the TiNi3 structure occur selectively in alloys of Ti-group elements with Ni-group elements. In AB3 alloys of Ti-group and V-group elements with Co-group elements the AuCu3-type structure predominates.' The vCO3 structure, which was determined very recently,' has hexagonal symmetry, but the actual atomic arrangement here, too, is rather closely related to the ordered cubic structure of AuCu3-type. However, an ordered hexagonal close-packed structure of the MgCd3-type occurs in MOCO33 and WCO3.4 Consequently, the question arises as to whether or not the crystal structure of MoNi3 is also of the MgCd3-type. Grube and winkler5 found that MoNi3 has a hexagonal close-packed structure with a = 2.54A and c/a = 1.65. They pointed out that some additional weak diffraction lines could be observed in the powder pattern, which may have been due to an ordered atomic arrangement in this phase. However, no detailed information was obtained by them and the structure was apparently not further investigated by others. The present work was, therefore, undertaken in an attempt to determine in detail the structure of MoNi3, and to investigate the possibility of ordering. EXPERIMENTAL METHODS Alloys used in the present work were arc-melted in a water-cooled copper crucible under helium atmosphere. Electrolytic nickel and molybdenum, both 99.9 pct pure, were used. Chemical analyses were not made, but the melting loss was not higher than 2 pct for any alloy. Ingots were first homogenized at 1200°C for 48hr, quenched, heavily cold worked, and then annealed at 820" or 860°C for 1 week, followed by quenching in cold water. Powder specimens for X-ray work were prepared by crushing the heat-treated solid specimens. In order to remove strains, the powders were reannealed in evacuated scaled fused silica capsules for 6 hr at the same temperature at which the corresponding solid specimens were annealed. X-ray photographs were taken with an asymmetric focussing camera, using unfiltered CrK or CuK radiation. EXPERIMENTAL RESULTS The X-ray diffraction patterns of alloys containing 20.8, 25, and 26.4 at. pct Mo, homogenized at 1200°C, showed the face-centered-cubic structure of the Ni-base a-solid solution. It was revealed, however, by micrographic examination that the 26.4 at. pct Mo alloy contained in addition very small amounts of a second phase, in accordance with the phase diagram.6 On the other hand, the 20.8 at. pct Mo alloy after annealing at 820°C gave the X-ray diffraction pattern of the ordered face-centered-tetragonal MONi4.7 In this pattern several additional weak diffraction lines were also observed, corresponding to the strongest diffraction lines of MoNi3. The alloys containing 25 and 26.4 at. pct Mo after annealing at 820" or 860°C gave X-ray diffraction patterns, as shown in Tables I and 11, corresponding to MoNi3. Each one of the reflections which could be tentatively indexed on the hexagonal close-packed cell of Grube and Winkler,5 with the exception of the basal plane reflections, was split into a doublet, as seen in Table I. Since microscopically the alloy consisted of a single phase, it seemed probable that the lattice of MoNi3 is actually slightly deformed, as compared with the tentative hexagonal unit cell. In addition to these diffraction lines, several weak lines were also present, as shown in Table 11, which could not be indexed at all on the hexagonal close-packed cell considered. Satisfactory indexing of all diffraction lines observed was found to be possible by using an orthorhombic unit cell with ao = 5.064A, ft = 4.224A, and c = 4.448A. These values, whose accuracy is estimated to approximately ± 0.008A, correspond to 95.14A3 for the volume of the unit cell, and to an X-ray density of 9.50 g per cm3. If no attention were paid to the weak reflections listed in Table II, a reduced -unit cell of half the volume (a = 2.532A, b = 4.448A, and c = 4.224A), closely related to the orthohexagonal cell, might be used. The dimensions of the orthohexagonal cell of the same volume as the reduced cell are: a = 2.562A, b = 4.437 A, and c = 4.183A. It may be seen that in the reduced cell the a axis is slightly shorter, while the b and c axes are slightly longer than those corresponding to the orthohexagonal cell of the same volume. This slight orthorhombic distortion is re-

Jan 1, 1960

By Randall L. Neal

This paper discusses the impact of taxes at the state and federal level on typical on-shore oil and gas exploration economics in the USA. Taxes considered are the windfall profits excise tax, state production (or severance) taxes, state income tax, and federal income tax. Also considered will be market prices for oil and gas in the USA. The effect of government take as a percent of revenue, on rate of return, discounted Payout, and discounted cumulative cash flow is shown on the attached tables. The conclusion drawn is that tax laws, while rarely the most important factor to be considered when drilling a well, can have significant impact on the profitability of oil and gas ventures, and should be considered when determining where to drill. Hypothetical exploration wells were analyzed for the impact of tax laws on project profitability. The results of this study show that when factors other than taxes are postulated to be the same (such as producing rate, capital, operating costs, and prices), cash flow can vary by as much as 68% due to the differences in the tax laws. Other significant findings for the cases studied include: (a) that discounted payout varied by as much as 1.8 years, (b) that rate of return differed by up to 67% and (c) the total tax rate as a percentage of revenue had a maximum variance of 33%.

Jan 1, 1982

[Aase, Qlenn D., (Junior Member '40) Jr. Met.. American Smelt. & Refin. Co., Selby. Calif. Abadie, Henry G., (Junior Member '43) Petr. Engr.. Avenal, Calif. Abbott, Clarence E., (Member '04) Civil En=.. V.P.. Tennessee Coal. Iron & R.R. Co., 1542 Brown biarx Bldg.. Birminpham, Aln. Abbott. Fred E., Jr., (Member '44) Petr. Engr., C/O Arabian Anierican Oil Co.. A.P.O. 816. c/o Postmaster, New York, N. Y. Abel, Raymond L., (Member '28) Chem. Engr.. C. O., Pittsburgh Chem. Warfare Procurenlent Dist.. American Bank Bldg., Pittsburph. Pa. Abel, Walter D., (Member '32) Min. Engr.. Supvr. Engr.. RFC, Los Angeles, Calif.]

Jan 1, 1946

By J. F. Myers, F. M. Lewis

C. G. McLACHLAN*-I have read this paper with considerable interest and wish to congratulate the authors on the care with which they carried out their experiments and for the detailed sizing data they have presented. 011 the other hand I do not feel that these data establish their contention that "with other factors the same, the work accomplished in a fine crushing rod mill is directly proportional to the rotating speed." My reason for making this statement is that their conclusion is based on the percentage of minus 65 mesh material produced at each of the speeds at which their tests were run. The rod mill is, however, not a fine grinding machine and therefore figures based on minus 65 mesh production are figures outside the range at which it operates to best advantage. Further, if rod mill performance is to be judged on the production of such material it should have been established that a rod mill will produce it as effectively as a ball mill. To check this last point I have gone over some of the rod and ball mill grind-ing figures for our Waite-Atnulet operation and find that the ball mill at that property produces more minus 65 mesh material per horsepower than the rod mill. Moreover, this comparison is even more favorable to the ball mill if it is limited to minus 100 mesh production. It therefore seems to me that the most satisfactory basis on which to try to com-pare the performance of the rod mill in the present case is by taking a weighted average of all the new surface produced per horsepower. W. H. Coghill3 has published data which can be applied to the sizing figures presented by the authors, and if this is done the units of new surface per horsepower produced in the Tennessee tests are as follows: Admittedly the increment of increase in new surface per horsepower shown in the foregoing figures is not great, but its trend is nevertheless definitely in favor of slower speed operation, for the conditions under which these particular tests were run. I also feel that some information regarding liner contour should have been given as I think it will be found that a mill which is equipped with liners which lift the rod load can be run at a slower speed than a mill in which the liners are comparatively smooth. J. F. MYERS and F. M. LEWIS (authors' reply)—The position taken by Mr. McLachlan is to be respected even though we are all aware of the faults of surface considerations. As he points out. the increment of increase is very small. It is so small in fact that for all practical purposes it does not conflict with the conclusions of the paper. The authors appreciate Mr. McLachlan's comprehensive study of the data.

Jan 1, 1950

By B. M. Larsen, T. E. Brower

A perspective is presented of the steel plant sulphur distribution and elimination problem from coal to liquid steel ready for teeming, giving distributions of sulphur over a range of coke sulphur content, and some methods of sulphur control, in the blast furnace, external desulphuriza-tion between blast furnace and open hearth, distribution between fuel, slag, and metal, and methods and limitations of control of sulphur in the open hearth furnace. AS a part of the 1951 AIME symposium on sulphur in steelmaking, it was thought that a discussion of the distribution of sulphur throughout the whole series of operations, from coal and ore to finished steel ingots, might have some value in giving a perspective on the whole problem. The following discussion is an attempt to present such an overall picture. The order is that of the actual plant operations, beginning with a very brief consideration of the coking process. Sulphur in Coal and Coke Since by far the largest source of sulphur entering the steelmaking cycle is in the coal used to make coke for the blast furnace, it would seem reasonable to eliminate some of it, either from the coal, or the coke, or during the coking process. This has appeared impracticable up to the present, at least, for two main reasons: the low activity of the organic sulphur in either coal or coke, and because of price limitations involved in treating a low cost material such as coke. A variable portion, usually M or less, of the sulphur is present in coal in the form of pyrites or similar compounds, and a large part of this sulphur may be removed in the coal washery. Most of the sulphur, however, is normally present as "organic" sulphur, intimately associated with the coal structure. Its distribution prevents any separation by mechanical means. Its low activity makes improbable ' any rapid chemical removal, although hydrogen will remove sulphur from both coal and coke. Thus, prolonged recirculation of coke oven gas in the coking process would tend to leave a smaller percentage of the total sulphur in the coke residue. Table I shows a typical distribution of sulphur from coal into products in the coking process. As the sulphur in the coal increases, the sulphur in the coke tends to increase in about the same proportion. Sulphur in the Blast Furnace The best picture of the situation in the blast furnace is provided by a sulphur balance of raw materials entering, and of products leaving, the furnace. The difficulties in accurate weighing and sampling of the variable solid materials entering this process, and the number of hours required for the raw materials to descend through the furnace under variable operating conditions, make it difficult to obtain an accurate balance. However, balances made over periods of weeks or months tend to average out some of these uncertainties. Table I1 presents three typical sulphur balances similar to a number that the writers have calculated. In most of these the slag volume calculated from the sulphur balance is, in some instances more, and in other instances less, than the value corresponding to the best input and output balances of the other slag constituents (lime, silica, alumina, etc.). Probably the greatest source of error in these calculations is the sulphur content of the slag. Despite some possible inaccuracies the balances of Table II show rather definitely the following points: 1—That 87 to 95 pct of the total sulphur input is in the coke and 95 to 97 pct of the total sulphur output is in the slag. Also, that if any sulphur leaves the furnace with the gas it is relatively small, amounting to a possible 1 pct or less. 2—At the lower sulphur coke level of 0.86 pct the total amount of sulphur charged is 15 Ib of sulphur per ton iron increasing to 26 lb per ton at the higher sulphur, intimately associated with the coal struc-rare burdens containing sulphur-rich ores will the total sulphur burden fail to be nearly proportional to the content in the coke used. 3—The 7 to 9 pct of the total sulphur input from the limestone of furnaces B and C is due to the relatively high sulphur content of the stone, 0.226 and 0.265 pct, respectively. In the case of furnace A, the sulphur content of the limestone was only 0.06 pct which resulted in only 3 pct of the total sulphur input coming from this source. It is rather interesting to compare the sulphur balances of a typical ferromanganese furnace with

Jan 1, 1952

By E. C. Wright

FOR many years the cost of making pig iron and steel in the Birmingham district has been about the lowest in the United States. The close proximity of the important raw materials such as coal, iron ore, limestone, and the large available scrap supply made it possible to assemble all of the important ingredients necessary for steel- making with only nominal costs for transportation. Both iron ore and coal were being mined in this district at one time for about $1 per ton from underground operations. At that time mining wages were low everywhere and the labor rate in the South was considerably below that of other mining districts. This situation persisted until the emergence of labor unions as an economic and political force, emigation of southern labor to northern plants, and continued growth of industry in the South in the years following the depression of 1932. Since that time union organizing of miners and steel workers throughout the nation has increased labor costs in mining and steelmaking. This influence has been felt particularly in underground mining operations since the proportion of labor cost to total cost is still high. The previous advantage in basic labor rate in the South has been almost entirely eliminated by the equalization of labor rates in basic industries by national unions. Since 1945 these influences have been especially noticeable in increasing the cost of mining coal and iron ore in the South. The northern steel districts are still being largely supplied with iron ore from the Minnesota open-pit mines and the cost of this ore has not increased nearly as much as the cost of ore obtained from underground mines in Birmingham. A similar situation exists in coal mining; the thinner seams in Alabama are not so amenable to mechanization as the northern mines and, as a result, the output per man-day in southern mines is only about three tons of coal as compared to five or six tons per man-day in the large captive mines of West Vir-

Jan 1, 1950

By F. H. Gilpin

SINCE Noah pitched his ark within and without with pitch, the use of asphalt in human endeavor has been increasing-for Noah's pitch was asphalt. Asphalt is a bituminous material found in nature, either pure or admixed with smaller or greater quanti-ties of mineral and non-mineral materials, or obtained by the refining of crude asphaltic-base petroleum under proper methods of control. Native or "natural" asphalts are scattered through-out the world, though the commercial value of the various deposits varies greatly, depending upon both their accessibility and magnitude and the quality of the material found. It is an acknowledged fact that such asphalts have been produced through natural causes by practically the same application of tempera-ture and pressure as are used in the modern refining of crude asphaltic-base petroleum. The best known of all the native asphalt deposits are those of Trinidad Lake in the Island of Trinidad, British West Indies, and of Bermudez Lake in Vene-zuela. Asphalt from Trinidad Lake, after refining to remove organic and some inorganic diluents, contains approximately 35 per cent, of inorganic residue, and the asphalt thus produced must be fluxed with lighter asphaltic or semi-asphaltic base oil to make it com-mercially utilizable. The refined asphalt obtained from the Bermudez Lake deposit contains from 4 to 6 per cent. of inorganic material which cannot be removed. This asphalt, also, must be fluxed to produce com-mercial products. Small quantities of similar materials are available in other locations. The best pure native asphalt' is known as. gilsonite and is mined in com-mercial quantities in the State of Utah. In numerous places in the United States, particularly Oklahoma and Kentucky, there are deposits of sand¬stone and limestone impregnated with bitumen, which are known as rock asphalts. These rock asphalts may be used, particularly in the paving industry, either as found or by slight fluxing; from some deposits the asphalt is extracted and marketed commercially.

Jan 2, 1923

By Wallace E. Pratt

TO SERVE their primary function of balancing supply with demand. crude-oil prices must not only return full cost plus a reasonable earning to the efficient producer but they must also offer an additional reward to stimulate exploration sufficiently to maintain adequate reserves. High prices increase the volume and efficiency of exploration; low prig e- -Idle exploration. Over the last decade average prices for crude oil have been much lower than for the proceeding ten years, and lower even than the average over the life of industry. Under these circumstances no one should be surprised to learn that over this same recent period of discovery of new oil fields has also lagged and fallen below its average level for the previous decade. Crude oil prices have been too ion to support the required activity in wildcatting.

Jan 1, 1941

By Zay Jeffries

Tungsten has the highest melting point of all the known metals, namely 3350 C.; it is one of the hardest of the metals; it has the highest equiaxing or recrystallization temperature after strain hardening, of any pure metal known. It is particularly distinguished because, when composed of small equiaxed grains, it is extremely brittle and fragile at room temperature, and when possessing a fibrous structure it may be ductile and pliable at room temperature. The common ductile metals act in exactly the opposite manner in this respect. The present paper will include a brief note regarding the manufacture of wrought and ductile tungsten. The metallography of wrought and ductile tungsten in the various stages of manufacture will be considered more or less in detail. The general relationships between the properties of tungsten and other metals will also be considered. A discussion will be given explaining why fibrous tungsten is ductile at room temperature, even though past experience with other metals would indicate that it should be brittle. Finally, a brief note regarding some new fundamental metallographic propositions relating to all metals will be given. Manufacture of Wrought and Ductile Tungsten Up to about 10 years ago, it had not been possible to work tungsten mechanically. About the year 1908, Dr. William D. Coolidge, of the General Electrie Go., produced ductile tungsten from what was then supposed to be an inherently brittle metal and which, in fact, was inherently brittle in its normal state, that is, when composed of equiaxed grains. Since that time many products, chief among which are the filaments for electric incandescent lamps, have been made from wrought and ductile tungsten. Tungsten is produced chiefly from the minerals wolframite and scheelite.1-8 The ores may be reduced in many ways. For example, the ore may be fused with alkali carbonates and the fusion dissolved in water; sodium tungstate is formed, which is soluble in water. This

Jan 1, 1919

By David C. Jonson, W. Bruce MacKenzie, Arthur A. Bookstrom, Vaughn E. Surface, Neil K. Muncaster, Stewart R. Wallace

In mid-Tertiary time a wet silici-alkalic magma penetrated the Precambrian rocks of what is now the Tenmile Range of Central Colorado and formed the Climax Stock. The stock is a composite one and was intruded in four separate irruptions, each giving rise to a major hydrothermal event. The first three of these produced large stockwork ore bodies that cap and flank the tops of their respective source intrusives; the fourth, and last, yielded almost no commercial mineralization. The ore bodies and their related zones of alteration are circular to ring-shaped in plan and arcuate in section. The different phases of the stock are so positioned with respect to each other that many of the circular and arcuate zones of mineralization and alteration overlap or are juxtaposed. Evidence of a time separation between the different ore bodies is found in certain dikes that were intruded between periods of mineralization and are well mineralized in one ore body but are barren in another. If it is assumed that the parent magma at Climax contained 10 per cent "water," that the "water" contained 0.1 grams per liter of molybdenum, and that the processes of extraction were 100 per cent efficient, then approximately 10 cubic miles of magma would be required for the formation of each ore body. The volume requirements, taken in conjunction with the cross-sectional areas of the different phases of the stock to explored depths, suggest to the authors that each magma chamber was columnar, extended to a depth of thousands of feet, and was connected with a much larger master reservoir. The repetition of similar intrusive, structural, and hydrothermal events, indicates periodic tapping of this reservoir. A regular chemical evolution of the parent magma is suggested by the systematic change in metal ratios and differences in the sites of deposition, relative to the source intrusive, in each of the four separate igneous hydrothermal stages. The preparation of ground was due to changes in magmatic and/ or hydrothermal pressures within the igneous-hydrothermal columns; small, repeated, up and down movements of the rock enclosing the tops of the columns formed the stockwork fractures into which the mineralizers penetrated. The forceful emplacement of each successive phase of the Climax Stock resulted in a slight doming and rotation to the westward of the earlier-formed geologic features. Postore normal displacement along the Mosquito fault is estimated at about 9000 feet. Part of one ore body was cut by the fault and lies at depth below the Paleozoic sedimentary strata on the hanging wall. On the footwall side of the fault, subaerial erosion and glaciation removed a large part of one ore body and uncovered the top of a second.

Jan 1, 1968

By Kidd, Robert L.

INASMUCH as galena and sphalerite flotation concentrates are being produced that contain over 95 per cent galena or sphalerite, it is not unreasonable to believe that a flotation concentrate assaying at least 80 per cent of native gold can he secured provided the gold is free. As yet, little if any fundamental information has been published concerning the flotation of free gold either alone or in the presence of sulfides. So far, we are unable to make as complete a separation of gold from sulfide minerals by flotation as is possible in, the separation of one sulfide from another by this method. An introductory study of the flotation of several free gold ores has been made in our Utah laboratories. For this study three general types of gold ores were chosen, namely: (1) Quartzite containing 0.26 oz. gold per ton in which no base metals are present; (2) sulfide ore (2.04 oz. Au; 1.31 oz. AO containing pyrite as the only sulfide present and the gold free; and (3) oxidized ore (1.10 oz. Au; 0.70 oz. Ag) from an oxidized zone of the vein from which sulfide ore (No. 2) was taken; little sulfide iron was present.

Jan 1, 1932

THE Executive Board of The American Engineering Council met in Pittsburgh, May 26 and 27. Its actions on the licensing of engineers and on the Employment Bureau are printed at length elsewhere in this issue. The board announced plans purposing the solution of the national problems of water power and forestry, upon which "the industrial development of the nation and the standard of living of future generations largely depends. The whole Federal water-power situation is in so critical a condition that immediate constructive action by the Government to conserve the public interests, involving vast consequences of economic and Federal policy, is necessary. After a long discussion during which the water-power problem as it affects Government reorganization was reviewed and Henry Ford's Muscle Shoal's plan was discussed, the board decided to lay the entire question before President Harding. A national movement to conserve the nation's forests, in which engineers, the U. S. Forestry Service, the forestry services of the states, universities and technical schools, and other groups such as the farmers, the railroads, and lumbermen, shall pool their efforts, was set in motion by the engineers. The work will be in charge of a Reforestation Committee of the Council, headed by Charles H. MacDowell of Chicago. Mov-ing picture interests will be asked to aid. The board pledged its support to President Harding in his plan for Government reorganization. In adopting the report of its Committee on Public Affairs, headed by J. Parke Channing of New York, the Executive Board of the council determined, in the event of the failure of the President's efforts to bring about greater economy and ffieciency in national affairs by regrouping of Federal functions, to press independ-ently a nation-wide movement for the establishment of a Department of Public Works. Progress in a national survey of the two-shift day in American industries was reported by the Council's Committee on Work Periods in Continuous Industries. This survey, called the most extensive of its kind ever made, has been in progress for more than a year; and purposes an exposition of industrial conditions which shall form a basis for establishing the relative merits of three shifts of eight hours each and two shifts of twelve hours each.

Jan 7, 1922

By F. C. Greene

The oil and gas industry in Missouri in 1934 continued along the same lines that have marked the previous years. One new gas pool has been opened, others have been extended and in one oil pool a 25-bbl. well was completed. Missouri has no laws or regulations relating to drilling or the filing of well logs and the Geological Survey depends on its own scouting activities to obtain information. The data herein have been taken largely from a paper by the author recently published in the 58th Biennial Report of the State Geologist of Missouri. That report is available on application to H. A. Buehler, State Geologist, Rolla, Missouri, accompanied by ten cents in stamps, the amount of the postage. The preliminary figures, subject to revision, indicate that before the end of December, 1932, there were 2495 completions, of which 320 were oil wells, 1139 were gas wells and 1036 were dry. Over half of the oil wells were drilled in the Richards-Stotesbury area of Vernon County and were pumped for only a short period of time. During the period 1933-34 there were 201 completions, of which 10 were oil wells with an initial daily capacity of 100 bbl., 90 were gas wells, with an open flow of 26,578,256 cu. ft., and 101 were dry. The most active areas in drilling for gas in 1934 were the Marota area, sec. 17, T.49N., R.32W., Jackson County, the Grandview area in T.47N., R.33W., Jackson County, and the Plattsburg area in Clinton County. The Knoche oil pool in sec. 16, T.46N., R.33W., Cass County, was the scene of the only important oil development. In the Marota pool nine wells were completed to the Squirrel sand, with a combined open flow of about 5,000,000 cu. ft. The pool is on a small symmetrical dome with a closure of at least 30 ft. The average depth of the wells is 450 ft. The Squirrel sand (Upper Cherokee, Pennsylvanian) had a thickness of 94 ft. in a near-by dry hole, but only the upper 30 or 40 ft. is drilled in the producing wells. The largest well

Jan 1, 1935

Levi Holbrook was born in Westboro, Mass., March 7, 1836. He was a descendant of John Holbrook, who came from England in 1660 and settled in the Massachusetts Bay Colony. Mr. Holbrook was prepared for college at Williston Seminary, East-hampton, Mass., and after one year spent in the West, he entered Yale. He was a, member of Phi Beta Kappa and of Linonia. During the six months following his graduation he was in Boston, under medical treatment for his cyes; then he took a horseback trip across the Rocky Mountains to the Columbia River and back, and resided in Danville, Va., for a time. From 1860 to 1863, as his eyes permitted, he was a student of modern languages and literature in Cambridge, Mass., part of the time being a resident graduate at Harvard University. Finally, however, he was obliged to abandon the idea of a literary life and from 1864 to 1867 he was engaged in financial business in Boston. The following year, he spent in New York, and then traveled for a year in Europe, Egypt and Asia Minor. In 1871, he returned to New York City. Mr. Holbrook was a member of the New England Historic Gcncalogical Society, the Society of Colonial Wars, and the Sons of the Revolution, was registrar general of the Order of the Founders and Patriots of America from 1915 to 1920, and had been governor of the New York society of that order. He was also a member of the American Fine Arts Society, the Order of the Cincinnati, the American Geographical Society (of which he was a councillor and secretary). and the Geographical Society of America. He joined the American Institute of Mining Engineers in 1878, and served as manager from 1895 to 1897. Mr. Holbrook died on July 26, 1922, from organic heart trouble, at his residence in Center Harbor, N. H. He was married Dec. 27, 1871, in Newark, N. Y., to Viola, daughter of John A, and Elizabeth (Failing)Vowers, who died on Sept. 10, less than six weeks after her husband. His two children, Clark Holbrook of Red Bank, N. J., and Mrs. Julian P. Smith, survive him

Jan 1, 1923

Levi Holbrook was born in Westboro, Mass., March 7, 1836. He was a descendant of John Holbrook, who came from England in 1660 and settled in the Massachusetts Bay Colony. Mr. Holbrook was prepared for college at Williston Seminary, East-hampton, Mass., and after one year spent in the West, he entered Yale. He was a, member of Phi Beta Kappa and of Linonia. During the six months following his graduation he was in Boston, under medical treatment for his cyes; then he took a horseback trip across the Rocky Mountains to the Columbia River and back, and resided in Danville, Va., for a time. From 1860 to 1863, as his eyes permitted, he was a student of modern languages and literature in Cambridge, Mass., part of the time being a resident graduate at Harvard University. Finally, however, he was obliged to abandon the idea of a literary life and from 1864 to 1867 he was engaged in financial business in Boston. The following year, he spent in New York, and then traveled for a year in Europe, Egypt and Asia Minor. In 1871, he returned to New York City. Mr. Holbrook was a member of the New England Historic Gcncalogical Society, the Society of Colonial Wars, and the Sons of the Revolution, was registrar general of the Order of the Founders and Patriots of America from 1915 to 1920, and had been governor of the New York society of that order. He was also a member of the American Fine Arts Society, the Order of the Cincinnati, the American Geographical Society (of which he was a councillor and secretary). and the Geographical Society of America. He joined the American Institute of Mining Engineers in 1878, and served as manager from 1895 to 1897. Mr. Holbrook died on July 26, 1922, from organic heart trouble, at his residence in Center Harbor, N. H. He was married Dec. 27, 1871, in Newark, N. Y., to Viola, daughter of John A, and Elizabeth (Failing)Vowers, who died on Sept. 10, less than six weeks after her husband. His two children, Clark Holbrook of Red Bank, N. J., and Mrs. Julian P. Smith, survive him

Jan 1, 1923