Search Documents

By Earnshaw Cook, H. S. Avery, J. A. Fellows

TEe increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni; 16 per cent Cr, 35 per cent Ni; 12 per cent Cr, 60 per cent Ni; etc.) in recent years has been accompanied by continued demands by the consumer for improvement in properties. The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties. To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created. It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloys presented in a companion paper. The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized. The Creep Test Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure. The creep-test iaboratory constructed for the American Brake Shoe and Foundry Co. is designed to permit I000-hr. tests in the temperature range of I200° to 2 200°F. with a choice of applied stress extending from jo to 50,000 lb. per sq. in. in increments of 50 lb. per sq. in. To simplify the calculation of weight combinations, the loading beams (Fig. I) are provided with counterweights to eliminate the tare. The precision of the knife-edges (10:I ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a I-gram weight attached to the loading shackle. Check of the loading weights proved the maximum error to be 0.06 per cent. Axial alignment is provided by crossed knife-edges in the grip seats. The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U.S. Steel Corporation. An 80 per cent Pt, zo per cent Rh No. 19 B. and S. gauge wire is used as the heating element. The details of -construction are shown in the radiograph reproduced in Fig. 2. The windings are held in place on an alundum tube with aludum cement; the distribution of turns is adjusted to give a maximum temperature gradient of , I°F. over a 4-in. gauge length (Fig. 3). To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length. Sixteen-inch coupons are used „ to reduce the temperature of the threaded joints and thus to facilitate removal from the grips. Thermal losses are minimized by refractory insulators cut to shape and surrounded by diatomaceous ear,th. The taps

Jan 1, 1942

By J. A. Fellows, Earnshaw Cook, H. S. Avery

TEe increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni; 16 per cent Cr, 35 per cent Ni; 12 per cent Cr, 60 per cent Ni; etc.) in recent years has been accompanied by continued demands by the consumer for improvement in properties. The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties. To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created. It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloys presented in a companion paper. The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized. The Creep Test Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure. The creep-test iaboratory constructed for the American Brake Shoe and Foundry Co. is designed to permit I000-hr. tests in the temperature range of I200° to 2 200°F. with a choice of applied stress extending from jo to 50,000 lb. per sq. in. in increments of 50 lb. per sq. in. To simplify the calculation of weight combinations, the loading beams (Fig. I) are provided with counterweights to eliminate the tare. The precision of the knife-edges (10:I ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a I-gram weight attached to the loading shackle. Check of the loading weights proved the maximum error to be 0.06 per cent. Axial alignment is provided by crossed knife-edges in the grip seats. The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U.S. Steel Corporation. An 80 per cent Pt, zo per cent Rh No. 19 B. and S. gauge wire is used as the heating element. The details of -construction are shown in the radiograph reproduced in Fig. 2. The windings are held in place on an alundum tube with aludum cement; the distribution of turns is adjusted to give a maximum temperature gradient of , I°F. over a 4-in. gauge length (Fig. 3). To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length. Sixteen-inch coupons are used „ to reduce the temperature of the threaded joints and thus to facilitate removal from the grips. Thermal losses are minimized by refractory insulators cut to shape and surrounded by diatomaceous ear,th. The taps

Jan 1, 1942

By Haley, D. F.

WHEN operations were first started at Climax in 1917 by the Climax Molybdenum Co., they were pioneering in the molybdenum industry for little was known relative to the uses of molybdenum or the metallurgy of molybdenite concentration. Concentration of molybdenite is relatively simple today but in 1916, when the Climax deposit first attracted attention, it presented serious difficulties. Little was known, in fact, even about the assaying of such low-grade molybdenum ores. Mine samples were sent to at least a dozen of the best laboratories in the United States and average values reported varied from 0.4 per cent to 1.0 per cent MOS2. Owing to the wide variations in MoS2 content obtained from reliable chemists, the actual value of the ore was most uncertain. This variation occurred repeat¬edly over a period of six months in 1917. It was finally decided, as a last resort, to cut several tons of sample from the tunnel and have a mill test made, using the recovered MoS2 per ton as the grade of the ore, for a small error in the assaying of the concentrate would not materially affect the results. These mill tests were made by the General Engineering Co. (Callow) at Salt Lake City. The results proved an ore of commercial grade and indicated the flotation process for the best metallurgy. Based upon these tests, the decision was made to build a 200-ton flotation plant. At this time, the art of flotation was

Jan 1, 1946

By P. D. Rao, H. B. Charmbury, D. R. Mitchell

As a result of a changing market pattern for anthracite, there is now an increasing demand for steam size and a decreasing demand for domestic sizes. To help the producer meet this new demand, the authors present the technical aspects of the problem of crushing domestic sizes to steam fineness and size. The market pattern for anthracite coal has changed considerably in recent years. The demand for domestic sizes has been gradually decreasing and the demand for the steam sizes has been increasing. The companies however aim for a maximum production of domestic sizes, since these sizes command premium prices. To meet the market demands, particularly in certain periods of the year, further size reduction of the coarse clean coal is necessary. The present practice of multistage crushing in toothed rolls leads to complicated flow arrangements and is high in cost. Data presented herein indicate that crushers with high reduction ratios could be used with a resulting simplification of crushing flows and an appreciable reduction of capital and operating costs. The different types of crushing equipment investigated included the rotary-type breaker, the jaw crusher, the impactor-type crusher, and the Aerofall mill. CURRENT PRACTICE The standard sizes of anthracite are presented in Table I and market specifications require that any given size be maintained with only a limited amount of oversize and undersize material. The 1958 prices of the various sizes also are presented, so it may be seen that size reduction is only performed when dictated by market demands. At the present time the general practice of crushing anthracite consists of removing the top size and crushing it in a toothed double roll crusher to the next largest size. Consequently, to reduce the domestic egg, stove, and nut sizes to steam sizes of pea, buck, rice, and barley, the original material must be screened to produce the three top sizes and each size must be crushed in three separate rolls to the next largest size. Each crushed product must then be rescreened to remove the oversize for re crush ing. Thus a typical operation would consist of scalping the egg size from a mixture, crushing it to stove size, and rescreening the product. This same cycle would be repeated for the stove and nut sizes requiring three screens and three crushers as well as conveying equipment to handle the crushed products. This results in an expensive series of operations to make a product which sells for a lower price. If the three top sizes are crushed in one operation to the smaller sizes then the yield of steam sizes is low and the production of Nos. 4 and 5 sizes is large. These sizes sell for lower prices than the steam sizes. A typical operation is presented in Fig. 1. From the figure it may be seen that the original cleaned anthracite contains 67.4 pet domestic sizes, 26.4 pct steam sizes, and 6.2 pct fines. After multistage crushing of the domestic to steam sizes the composition of the product is 0.6 pct domestic sizes, 89.6 pct steam sizes, and 9.8 pct fines. From a technical standpoint these results are reasonable but the handling and crushing costs are

Jan 1, 1961

By R. R. Sayers

THE South African Mining and Engineering Journal recently pointed out that no satisfactory solution of the question of compensation for silicosis can be arrived at by placing further liability of an inequitable nature upon the mines. There are at present 35 scheduled mines liable to contribute to the annual levy of $800,000 and provide for the net outstanding liability of $6,400,000. Several of these mines have, as yet, not been able to set aside sufficient funds against their out- standing liability to the Compensation Fund. The gold producers declare that the gold mining industry today is passing its zenith, and that the production of gold will decline, with a consequent lessening of the spending power of the mines, which in about ten years will be reduced to a great extent unless encouragement is given for the opening of new mines. It is during this period of decline that the mines will be required to meet the large burden already created by miners' phthisis. In England the Workmen's Compensation Act, 1925, was extended to industries involving exposure to asbestos dust.

Jan 1, 1931

By Basil B. Zavoico

PRODUCTION of crude it in the United States during 1939 totaled about 1.255,776,000 barrels, an average of 3,440,482 barrels per day, 3.41 per cent above the 1938 output of 1,214,355,000 barrels but 1.83 per cent below the record pro¬duction of 1,279,160,000 barrels, in 1937. However only the two-week shutdown of oil fields in the Southwestern States in August and September prevented the domestic crude production from establishing an all-time record in 1939. Demand for all petroleum products for the first ten months of 1939 showed an increase of 7.04 per cent over the similar period of 1938. Domestic demand for all petroleum products was particularly benefited by the increasing industrial activity, advancing 8.37 per cent above the like period of the preceding year equivalent to a volume increment of 256,810 barrels per day; with motor-fuel demand gaining 5.83 per cent and demand for all fuel oils gaining 12.15 per cent over the corresponding period of 1938. The export demand for the first ten months of 1939 was slightly below the export movements during the same period of 1938, declining 0.56 per cent. The European war was a major factor in 1939 for the petroleum industry in the United States, even if, at the end of the year, the war had not yet resulted in the expected large shipments to England and France.

Jan 1, 1940

Sponsored by the Utah Section of AIME, the 1960 Annual Rocky Mountain Minerals Conference brought more than 500 members of the mineral industry to the conference rooms of the Newhouse Hotel in Salt Lake City during the period October 5 to October 7. Under the overall supervision of J. M. Ehrhorn, general chairman, and H. E. Wright, assistant general chairman, the Conference offered 14 papers of technical interest in four sessions during the first two days, and it culminated in the Exploration Symposium held on the morning of October 7. The opening session of the Conference, meeting on the morning of October 5, heard R. P. Work, utility engineer of the Mountain Fuel Supply Co., discuss the growth and economic factors related to the use of natural gas in Utah. In his paper entitled Natural Gas Market In Utah, Mr. Work emphasized the very good prospects of natural gas serving almost all parts of that state. He mentioned that recently the El Paso pipeline, built to serve the Pacific Northwest with gas from Texas, has permitted natural gas to be available to Eastern Utah, and a tentatively planned pipeline from Green River, Wyo. to Southern California will bring natural gas to the central and southeast areas of the state.

Jan 11, 1960

By B. C. Allen, R. I. Jaffee, D. J. Maykuth

Wrought unalloyed iodide chromium, containing 39 to 95 ppm total interstitials, has a tensile transition temperature of —15°C. Re crystallizing at 1100°C causes the transition to rise to 90° to 390°C, depending on the purity, grain size, and cooling rate after annealing. At about the 100 ppm level, individual additions of carbon or nitrogen raise the transition of both wrought and recrystallized chromium by as much as 210°C, while oxygen has a lesser effect, and sulfur essentially no effect. High transitzon temperatures are exhibited by recrystallized and quenched chromium, and appear to be associated with the amount and distribution of inter-stitials. The latter cm be either in solid solution or in the form of precipitates within the grains or at the grain boundaries. Quench hardening in chromium is primarily caused by nitrogen. The hardness, re crystallization, and grain growth behavior of chromium with and without impurity additions were also investigated. BECAUSE of low density and good oxidation resistance, chromium-base alloys are potentially useful for elevated-temperature applications. The main deterrent to the use of chromium in structural applications is its lack of low-temperature ductility, especially in the recrystallized condition. Accumulated evidence has shown that the ductility of chromium is sensitive to purity. The objective of the current study was to determine the effect of common nonmetallic impurities on the tensile properties of high purity chromium. The separate effects of carbon, oxygen, nitrogen, and sulfur additions on the ductile-to-brittle transition were evaluated for wrought and recrystallized material after various cooling rates. EXPERIMENTAL WORK Unalloyed iodide chromium and seven impurity alloys containing individual carbon, oxygen, nitrogen, or sulfur additions were prepared in rod form. Nominal additions were 100 ppm C, N, and S, and 100 to 500 ppm O. The additions were about a factor of ten greater than the residual amounts in the unalloyed material. The seven alloys and two unalloyed compositions were consolidated into four-pound ingots by conventional consumable arc melting of pressed and welded electrodes under 0.5 atm of helium. Impurity additions were made to the electrode in the form of crushed master alloys. The impurity alloys were double melted to improve homogeneity. The ingots were broken down by extrusion at 1200°C in evacuated steel cans at a reduction ratio of 18 :1, using a molten borosilicate glass lubricant and a ram speed of 80 in. per min. The cans were removed by acid pickling, and the chromium core ground free of surface undulations. Cut lengths were sheathed in mild steel and swaged at 900°C until the core was about 1/4 in. in diam. Two additional 15-lb ingots of unalloyed chromium (ICr-3, ICr-4) were prepared by arc melting and broken down by 26:1 extrusion at 1250°C without a steel can. The billet was lubricated and protected from contamination by a coating of molten glass. The resulting extrusion was then sheath swaged as described previously. Representative chemical analyses of each of the materials, after removal of a 10-mil surface layer

Jan 1, 1963

By Barry K. McMahon

Following minor slope failures at the commencement of mining the west wall of the Kanmantoo Mine was redesigned from an overall slope between haul roads of 55° to 46°. This decision was based on a probabilistic analysis which indicated that 46° was the optimum economic slope.

Jan 1, 1983

By John M. Cigan

Samples of copper-lead concentrates from the mine of Cia Minerals Santander, Inc., a Peruvian subsidiary of the St. Joseph Lead Co. were recently subjected to special analysis. This concentrate was known to contain bismuth which, under some circumstances, might have incurred a smelter penalty. In this case, customers for the concentrate accepted it and requested a higher concentration of bismuth. Although chemical analysis would disclose the presence of the metal, it was not possible with equipment available at the mill in Peru to determine the mode of occurrence in the fine grained ores.

Jan 11, 1964

By NORMAN EBBLEY

NUMEROUS references have been made recently to "Alaska's oil reserves," and in view of the wartime petroleum situation sober thinking demands a dispassionate and scientific study and investigation of these reserves or supposed reserves. The question naturally arises, "Is there actually oil in Alaska, or are the reserves there a supposition?" True, in 1923 President Harding established Naval Petroleum Reserve No. 4 in Alaska, certainly implying that oil was there. This reserve, embracing about 35,000 sq. mi., was set aside on the advice of the Bureau of Engineering of the Navy Department and was based upon the existence of known petroleum seepages at Cape Simpson on the Arctic coast. The Cape Simpson seepages have been known for more than fifty years, but in spite of persistent rumors of other seepages in northern Alaska no definite evidence of their existence has been available.

Jan 1, 1944

By Albert E. Wiggin

PagE I. Early History of Boston & Montana Mill at Great Falls (1891 to 1905). 210 a. Original Mill Built in 1891.........210 b. Coarser Concentration Tried...211 c. Screen Sizing of Fine Jig Feed Introduced..211 d. Installation of Finer Grinding.......211 e. Steam Stamp Tried in Place of Blake Crushers..... 211 j. Mill Increased from Three to Six Sections........ 213 g. Tonnage Increased from 300 to 450 Tons per Section... 212 h. Round Tables Replaced by Wilfley Tables....212 I1. Hancock Jig Replaces Evans Jig...212 a. Description of Hancock Jig...213 - b. Tests Made on- Hancock Jig..213 1. Treating Natural Feed..215 2. Treating Sized Feed..215 3. Treating Classified Feed .215 c. Tests Made on Evans Jig...216 III. Richards Pulsator Classifier System...218 a. Experimental Work.....218 b. Installation of System in Section No. 4,....... 220 IV. Woodbury Classifier and Jig System.............222 V. The Great Falls System................ 222 a. As Installed at Anaconda............ 224 1. Coarse Crushing and Jigging Division...... 225 2. Hancock Jig Division........... 226 3. Fine Middling Division.......... 229 4. Table Division............. 230 5. Slime Division.........230 b. Special Features of Great ails Flow sheet....... 231 1. Development of Hancock Jig Flow Sheet..... 231 2. Development of Finishing Table Flow Sheet.... 232 3. Treatment of Coarse Middling Table Products .. 232 4. Results of Test Made on 500-Ton Section at Great Falls Mill...........234 VI. Comparison of Great Falls and Evans System at Anaconda.... 236

Jan 1, 1914

By W. W. Norton

The gradually increasing proportion of sulphide ores which lead smelters of to-day are called upon to handle has caused the roasting problem to become one of ever greater importance. Mines have increased in depth, methods of concentration have improved, competition in the purchase of ores has become more keen and it has been clear that new and modern methods of eliminating sulphur must receive a large share of attention. We may look back a score of years or so and recall the old hand roasters, some of which turned out a finely divided roasted product, and others fashioned with a "fuse-box" wherein the roasted ore was slagged. Then came mechanical furnaces of several types, the Bruckner cylinder, the Brown-O'Harra, the Ropp, and others, all designed to cut out the cumbersome hand labor of the old reverberatories. Roasting costs were thereupon reduced and tonnages stimulated to a gratifying extent. However, it seems to have been early recognized that this very feature of a greater amount of roasted sulphide ore as compared with oxide ore brought with it a train of difficulties at the blast furnaces. The mechanically roasted ore was fine physically, the blast furnaces were choked and the troubles of the smelterman were not at an end. Then the Huntington-Heberlein pot system of roasting appeared upon the scene, and later on the Dwight-Lloyd machines were invented, and inasmuch as both of these processes were designed not only to roast the ore but to agglomerate it as well, it was apparent that distinct steps in advance had been achieved. At the Murray plant, modern up-to-date roasting practice is fully exemplified and there are now in successful operation roasting furnaces or devices of several sorts: namely, Godfrey revolving-hearth furnaces, Wedge multiple-hearth mechanical roasters, Dwight-Lloyd sintering machines, and Huntington-Heberlein pots. Godfrey and Wedge furnaces will properly handle material high in sulphur, say ores with 25, 30, and 35 per cent. of that element; D. & L. machines and H. & H. pots will positively not treat efficiently ores or mixtures containing anywhere near the sulphur content mentioned, but are confined to charges containing in the neighborhood of 15 or 18 per cent. In passing, it may also be explained that, so far as the knowledge of the writer goes, Godfrey and Wedge furnaces do not economically eliminate sulphur to an extent

Jan 1, 1915

By AIME AIME

AMONG the recent mining and metallurgical developments in England great interest has been shown in the development of an iron-ore field covering 26,0.00 acres in Northamptonshire, containing 500,¬000,000 long tons of ore; and the erection at Corby, by Stewarts & Lloyds, of a modern basic bessemer steel plant and tube works. The entire project was planned to cost about £3,300,000. Many improvements have been made in the varied equipment that is being installed, some of which has set mew records for massiveness. There is, for instance, a new roll crusher, which has been manufactured by Hadfields, Limited, of Sheffield, the largest ever built in England, and weighing 130 tons. This machine, shown in Fig. 1, as erected at the Hadfields shops, is primarily designed to take blocks of iron ore as they come from the steam shovel. The maximum size is 54 by 48 by 36 in., hut occasional pieces slightly larger than this may be accommodated. The capacity is upwards of 500 tons per hour, the product passing to a secon-

Jan 1, 1934

By Johann F. Kerl

Autogenous batch grinding tests were performed in laboratory-scale tumbling mills with magnetite, limestone, and sandstone pebbles. The influence of pebble size, feed size, mill speed and loading, and grinding time on the fineness of grinding was investigated. Comparisons were made with the results from ball mill grinding experiments.

Jan 1, 1972

Jan 1, 1882

With a total value to date of well over $200,000.000.00 for its ore production, the Tintic mining district, which is about 100 miles southwest of Salt Lake City, ranks as one of the three main ore producing areas of Utah. In it are located the biggest silver mines of the country, silver having been the chief metal produced in the camp since its start. Tintic's silver production to date has a total value of over $1 00,000,000, approximately half of the value of the camp's ore production, the balance being roughly divided among lead, gold and copper. Discovery of the camp was made in the late sixties. Lack of transportation and ore reduction facilities delayed extensive development of the area for nearly a decade. In recent years Tintic's ore production has ranged from 350,000 to 400,000 tons annually. In 1924 the camp produced one-eighth of the silver produced in the nation with an output of 7,729,700 ounces. Its lead production was 77,765,000 pounds and its gold production 26,285 ounces.

Jan 1, 1925

By Renato G. Bautista, David C. Lindholm

The results of scale-up studies on a continuous, multistage horizontal mixer-settler extractor are presented. The chemical and mechanical system involves the separation of lanthanum from a mixture of rare earth chlorides using di(2-ethylhexyl) phosphoric acid as the solvent and dilute HCl as a scrub solution in a bench scale extractor. Each stage has a hold-up of 2.6 l. A single stage unit is utilized for scale- up studies. Results are obtained on four sizes of geometrically similar units, the largest being six times the volume of the original bench size. A unit operations technique is chosen so that mixing and settling can be examined independently. Variables examined include type of continuous phase, flow rate of inlet streams, and power input to the mixer. Inlet flow-rate ratios are kept constant for all tests. TWO potential methods of unbaffled pump-mixer scale-up are explored; the maintenance of constant impeller tip speed and constant power input. For the settler, the previously successful method of basing design on constant flow-rate per unit cross- sectional area is used.

Jan 1, 1977

By Gordon E. Frantti

Under the auspices of the Geophysical Committee of Michigan College of Mining and Technology, an investigation was made in Michigan's Upper Peninsula to obtain geophysical data related to the regional subsurface geology in the area covered by Paleozoic sediments. The area surveyed includes that portion of the Upper Peninsula which lies between R18W to R26W and T41N and T49N, covering approximately 1300 square miles. On the index map, Fig. 1, it is represented by the cross-hatched zone west of Munising. Four of the five sites of detailed investigation are indicated by the letters A, B, C, and D. A detailed gravity and magnetic survey had previously been conducted by J. G. Wilson near Perkins, 8 miles north of Rapid River, on a local anomalous area. Results of his work, which showed a large positive magnetic anomaly associated with a gravity anomaly, aroused interest in the possible economic significance of the formations underlying the Paleozoic sediments in this part of the Upper Peninsula.

Jan 1, 1956

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members) Member, Graduate Colorado School of Mines. Four years' experience in West and Northwest. Two years with American Smelting and Refining Co. Wishes to join field party on geological work, mining or areal, where opportunity will be given to be of direct assistance to chief of party in solution of field problems. Age, 26. Unmarried. At liberty June 1. No. 342. Member, technical graduate, aged 30, with' 7 years' experience in concentrating and mining, desires a position of authority with reliable company. At present employed. No. 343. Member. Ambitious, energetic, tactful engineer, college graduate, married, aged 30, desires location with a large coal mining organization. Seven years with present employers -n middle west; has had broad experience in the past eight years on examination, development and construction; successful record in handling men. Position must carry responsible work and a future. Will go anywhere for proper opportunity. Exceptional references as to reliability, character and capacity for work. No. 344.

Jan 3, 1917