Search Documents

By R. A. Deju, R. B. Bhappu

The basic structural unit of all silicate minerals is a tetrahedron with a silicon atom at the center and four oxygen atoms at the corners. The oxygen-silicon distance is about 1.6 & and the oxygen-oxygen distance about 2.6 &. The different types of oxygen-silicon frameworks in the various silicates are based entirely on the combinations of the tetra-hedral oxygen-silicon groups through sharing of oxygen atoms. In recent years, infrared spectroscopy has permitted estimation of the ratio of the ionic character of the oxygen-silicon bond to be a few times that of the oxygen-carbon bond and the ratio of electro-negativity of the two bonds has also substantiated this finding. On this basis, it is generally accepted that the oxygen-silicon bond is the strongest one occurring in silicate minerals. As the oxygen-silicon ratio increases from quartz to the olivines, a greater percentage of the oxygen bonding power is available for bonding to cations other than silicon. Hence, with an increasing oxygen-silicon ratio, there is increasing oxygen-to-metal bonding. Upon the fracturing of a silicate mineral crystal, the oxygen-metal bond, which is almost entirely ionic in character, should break more easily than the stronger oxygen-silicon bond, resulting in a greater number of unsatisfied negative forces on the surface. If, then the mineral is immersed in a liquid containing hydrogen ions, these negative forces should tend to be neutralized by hydrogen ions from solution, resulting in a change of the pH of the solution. An increase in the degree of adsorption of hydrogen ions is to be expected as the oxygen-silicon ratio in the crystal structure increases. This study attempted to correlate the oxygen-silicon ratio for various representative silicate minerals to the adsorption of hydrogen ions. Experiments to determine the effect of surface area on this adsorption and to investigate the effect of surface iron were also conducted. It is believed that such studies of the surface properties of silicate minerals will supply pertinent information about their behavior in froth flotation systems. EXPERIMENTAL PROCEDURE Ion Exchange: Carefully selected, hand-picked samples of the minerals investigated were dry-crushed in a ceramic ball mill and sieved to obtain a minus 100 plus 200-mesh sample. The sized samples were then run through the electro-magnetic separator to remove any iron-bearing particles. A 10-g sample of each mineral was placed in 100 ml of freshly deionized water previously adjusted to a pH of 3.50 with HCl. The beaker containing the sample and the water was placed under a bell jar from which the air was displaced at once by nitrogen gas from a tank. All experiments were carried out in a nitrogen atmosphere. The sample and solution were stirred gently but continuously during the entire experiment, the stirring speed being kept about the same for all runs. Changes in pH were followed with a Beckman Zeromatic pH meter and recorded on a

Jan 1, 1967

By GEO M. FOWLER

AN appraisal of the activities of the mining geologists during 1936 clearly indicates the ever in- creasing utilization of geology in the search for ore. Few men with geo- logic training are idle at present; this is particularly true regarding recent graduates. Many have accepted employment in distant fields, such as the Philippines and South America, and greatly increased mineral production from these places reflects their activities. In North America, regions of intense mineralization formerly important are being restudied in greater de- tail and with better understanding; as a result, new mineral wealth is being found in many such districts. Much is being done by private companies and individuals, and it is to be hoped that mining companies will increasingly make available the purely scientific results of such studies by permitting their geologists to publish. On such generosity to a large extent will future advances in ore finding depend.

Jan 1, 1937

By John A. Gann

THE Iron and Steel Division has shared in the general increased activity of the industry. The fall meeting at Chicago was not only well attended but particularly characterized by the virility and scope of the discussions at the various sessions. The program for the February meeting indicates a similar interest in technological developments. The Blast-Furnace Committee continues to have the hearty support of the industry with discussions of such a nature as to be of real help to the operator as well ass the technologist. The work of the Open-Hearth Committee continues to be outstanding, with ever increasing attendance and ever mounting interest in the meetings. Formation of a conference on the physical chemistry of steelmaking has given those interested in this phase of work an organization allowing the same

Jan 1, 1936

By A. Hultgren, G. Phragmén

Page Outline of Progress of Knowledge and Theories about Gas Evolution in Steel Ingots. and Its Influence on Crystallization and Segregation................ 134 Object of Present Investigation........................................... 148 Theoretical Discussion of Process of Solidification........................... 149 Gas Given Off from Rimming Steel during Solidification................... 149 Equilibrium Diagram of the Iron-carbon-oxygen Alloys................... 151 Solidification of Pure Iron-carbon-oxygen Alloys.......................... 157 Solidification when Carbon Monoxide Is Given Off at Constant Pressure... 157 Solidification when Gas Evolution Is Suppressed....................... 158 Schematic Application on Solidification of Rimming-steel Ingots.......... 159 Influence of Manganese, Sulphur and Phosphorus......................... 160 Experimental work..................................................... 162 Liquid Steel and the Mold Gas......................................... 162 Ingots Investigated and Methods Used.................................. 165 Ingot structure....................................................... 174 Structure of Rim Zone.............................................. 174 Structure of Core................................................... 181 Structures Obtained under Special Conditions of Freezing................ 182 Distribution of Metalloids............................................. 187 Other Observations Made............................................. 192 General Discussion of Solidification Process................................. 195 Condition of Liquid Steel before Casting................................. 195 Rimming Period...................................................... 202 Composition of Rim Zone............................................. 225 Freezing after Top Is Closed........................................... 228 Slag Inclusions and Ingot Scum........................................ 234 Reaction between Gas in Blowholes and Surrounding Solid Steel during Cooling 235 Summary.............................................................. 237 Appendix—Preparation and Etching of Ingot Sections....................... 238 References............................................................. 239 In 1934, Jernkontoret (The Swedish Ironmasters' Association) appointed a committee for the study of the structure of rimming-steel ingots and the various phenomena associated with their solidification. The members of the committee, including those who have joined it later, have been: I. Bohm, B. D. Enlund, B. Kalling, M. Tigerschiöld, S. Wohlfahrt and the authors. The present paper‡ is a somewhat

Jan 1, 1939

By G. Phragmén, A. Hultgren

Page Outline of Progress of Knowledge and Theories about Gas Evolution in Steel Ingots. and Its Influence on Crystallization and Segregation................ 134 Object of Present Investigation........................................... 148 Theoretical Discussion of Process of Solidification........................... 149 Gas Given Off from Rimming Steel during Solidification................... 149 Equilibrium Diagram of the Iron-carbon-oxygen Alloys................... 151 Solidification of Pure Iron-carbon-oxygen Alloys.......................... 157 Solidification when Carbon Monoxide Is Given Off at Constant Pressure... 157 Solidification when Gas Evolution Is Suppressed....................... 158 Schematic Application on Solidification of Rimming-steel Ingots.......... 159 Influence of Manganese, Sulphur and Phosphorus......................... 160 Experimental work..................................................... 162 Liquid Steel and the Mold Gas......................................... 162 Ingots Investigated and Methods Used.................................. 165 Ingot structure....................................................... 174 Structure of Rim Zone.............................................. 174 Structure of Core................................................... 181 Structures Obtained under Special Conditions of Freezing................ 182 Distribution of Metalloids............................................. 187 Other Observations Made............................................. 192 General Discussion of Solidification Process................................. 195 Condition of Liquid Steel before Casting................................. 195 Rimming Period...................................................... 202 Composition of Rim Zone............................................. 225 Freezing after Top Is Closed........................................... 228 Slag Inclusions and Ingot Scum........................................ 234 Reaction between Gas in Blowholes and Surrounding Solid Steel during Cooling 235 Summary.............................................................. 237 Appendix—Preparation and Etching of Ingot Sections....................... 238 References............................................................. 239 In 1934, Jernkontoret (The Swedish Ironmasters' Association) appointed a committee for the study of the structure of rimming-steel ingots and the various phenomena associated with their solidification. The members of the committee, including those who have joined it later, have been: I. Bohm, B. D. Enlund, B. Kalling, M. Tigerschiöld, S. Wohlfahrt and the authors. The present paper‡ is a somewhat

Jan 1, 1939

By D. B. RUSHNORE, K. A. Pauly

Bulletin. No. 41, May, 1910. ABBREVIATIONS. Al. Ind., Alliance Industrielle. am. Elec'n.. . American. Electrician. Bull. As. Ing. El Bulletin de la Association des Ingenieurs Elec- triciens Sortis de l'Institut Electrotecnique Montefiore, Liege. Bull. Soc. bilge d' Elec Bulletin de la Société belge d'Electriciens. Col. Guard . Colliery Guardian. D. R. P Deutsches Reich Patent. Dilly. Poly Dingler's Polytechniches Journal. E. & DI. Jour Engineering and Mining Journal. E. T. Zeit Electrotechnische Zeitschrift. Eclair. Elec. L'Eclairage Electrique. 1;1. Anzeig Elektrotechnischer Anzeiger

Sep 1, 1910

By William L. Batt

IT IS becoming increasingly evident to management that it has other obligations than merely to earn dividends for stockholders. The head of one of America's largest organizations has stated it in these words: "There rests upon them a far broader responsibility than the mere production of goods and services, or solely the interests of their stockholders. They must assume the important obligation, through proper policy, of attuning industry to a rapidly changing world, from social as well as economic standpoints." Stockholders might as well reconcile themselves, therefore, to the fact that management cannot always put their interests first in the obligation of business enterprise: and that the legitimate requirements of customers and employees have acquired a new significance which must be recognized if the business of today is to prosper.

Jan 1, 1938

By M. D. Hassialis

THE object of a technical paper is to communicate new technical knowledge, the paper being the vehicle of communication and the existence of new knowledge its reason for being. It follows that the development of information worthy of communication, the criterion being novelty, is prerequisite to exercising the privilege of communication. The act of communication is achieved when the reader perceives the nature of the new knowledge, i.e., when he understands it. A paper achieving this objective is an acceptable technical paper. Development of new knowledge has as one of its purposes the increase of the existing state of knowledge and the enjoyment of the benefits derived therefrom. Technical knowledge is a collection of facts so ordered as to make apparent, relations existing between the facts. When the interrelations have been exposed the facts have been interpreted or explained Three broad, overlapping categories of technical papers may be recognized: papers consisting of (a) a report of facts, (b) an explanation of facts, or (c) a combination of a report and an interpretation. Ideally a technical paper should belong to one of the last two categories but current practice is to accept papers belonging to any of the three categories. Based on a small sample drawn from the scientific and engineering literature, the relative frequency of the three types is a: b: c:: 20:1:14. If the sample be limited to engineering literature, the ratios become a:c::2:1; type (b) being nonexistent. This large departure from the ideal is a consequent of the

Jan 1, 1948

By B. L. Averbach

THE rolling process may be considered as a case of a nonhomogeneous plastic flow. In such a heterogeneous deformation there is no direct general solution, and the plastic deformation varies from point to point as a function of the coordinates. It is practicable to determine these plastic strains only at the conclusion of the rolling process, and the local strains can be studied by observing the deformations produced in a suitably placed grid system. Strains at the surface of a bar after rolling have been reported by MacGregor and Coffin,' but the strain distributions within the bar have not been previously observed. Siebel² has investigated the plastic deformations resulting from wire-drawing by splitting the wire along its axis, milling a grid coordinate system on the inner plane surfaces, and binding the .wire together so that it would pull through a die as a single unit. This method was possible because of the rotational symmetry of the die. In the rolling process, however, such a system was not readily applicable. This paper describes another method of including a grid system, and reports some preliminary data on the plastic rolling strains within a square bar. Experimental Procedure 2.1 mm wide (144 network squares per sq in.) was punched from a thin lead sheet with a steel die and supported in a brass mold by thin copper wires. Pure tin was then poured around the grid to form a solid bar, with the network securely imbedded at. a given position. This bar was then machined to a square 15.2 mm (0.60 in.) wide, and then radiographed. The lead grid was quite adherent and sufficiently ductile to follow the deformation of the bar faithfully. The network lines also remained sharp enough to maintain a high radiographic contrast, and the tin bar, with the grid included, could withstand considerable deformation at room temperature without splitting at the interface. In order to fill the mold, it was necessary to cast the tin at 260-280°C and during pouring the lead grid was supported at short intervals to prevent warping. Some shrinkage cavities were encountered, but only bars which were free of shrinkage in the network region were used. This method is similar to the one employed by Steinberg" in an investigation of the strain distribution in a tensile specimen. Before rolling, the machined bars were radiographed in two directions to obtain accurate initial dimensions of each square and to observe whether the grid was straight and correctly positioned. The rolling was performed in a small hand mill with 2 in. diam rolls at room temperature, and a 20 pct reduction based on the original height was employed. The rolls were clean and no lubricant was used. Halfway through the bar, at the center of the network, the rolls were reversed and the bar extracted. These bars were then radiographed again

Jan 1, 1951

By H. W. McQuaid

IT IS usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effect of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide can result in total unfitness of low-carbon steel for, case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 2, 1922

By ALBERT P. J. BORDEAUX

THIS paper briefly describes the general outline of cyaniding silver-ores in Mexico, with special reference to personal experiments made in the Temascaltepec district. The most important papers on the subject deal with cyaniding gold-silver-ores, the gold predominating in value, so that the treatment is nearly the same as for gold-ores, the losses of silver being considered of little importance. I describe here the treatment of silver-gold-ores containing very little gold, which is more general in Mexico than elsewhere. The cyanide treatment, which was so successfully applied to gold-ores, did not succeed immediately with silver-ores on account of their varying composition. Gold occurs in nature usually in the native state, while silver occurs generally in combination with sulphur (argentite), and various combinations of sulphur, antimony, and arsenic. In former times there was a complete difference in the treatment of gold-ores and silver-ores. Amalgamation, which was successful with gold-ores, was generally inadequate with silver-ores. The usual treatment in Mexico for silver was the patio process, the theory of which was satisfactorily explained only quite recently by Mr. Ortega and others. GENERAL OUTLINE OP THE CYANIDE TREATMENT. The general tendency of the present practice is to slime the silver-ore as much as possible, and in order to obtain a higher efficiency, with less loss of cyanide, and greater speed, the following lines are observed 1. Crushing by stamps with 30- or 40-mesh screens, then crushing by Huntington or Chilean mills, through 60- or 80-mesh screens. 2. Concentration upon vanners.

Jan 1, 1910

By H. H. Moss

OXYACETYLENE .cutting has experienced rapid development in the last few years and greater advances and expansion and broader application may be expected in the immediate future. Marked changes in cutting practice may be expected as a result of the advances in metallurgical science that have produced special alloy steels with properties requiring different cutting techniques than for ordinary low-carbon steels. Much current attention is being directed to those problems of modified cutting practices. Cutting has thus ceased to be merely a shaping problem. It is rapidly coming to have a predominantly metallurgical aspect. The problem is no longer how to cut a given shape, but how to cut a given steel. The answer

Jan 1, 1936

By C. L. Clark

EVERY user of steel should ask himself whether or not he is taking full advantage of the discoveries of the steel metallurgists during the last few years, or is merely buying grades that looked to be the best five or ten years ago for various specific purposes and have since proved perfectly satisfactory in his plant. If he has not kept abreast of the times, then it is probable that something better has been developed, or something just as good that costs less. Though this article will have to do with steel for high-temperature applications primarily, marked advances have been made in steels for other purposes as well.

Jan 1, 1940

By Persifor Frazer

INTRODUCTION For various reasons I have not specified the locality where the research indicated in the following pages was undertaken. It will suffice to say that it was on the grounds of a villa once remote from, but now completely surrounded by, its neighboring city, and in close proximity to an industrial establishment of great extent and importance manufacturing many kinds of steel articles and employing upwards of thirty chimney-stacks for power and process work. The problem was to discover the cause or causes of the mortality to trees and plants on the place, and to trace these causes to their origin. Before undertaking this experimental work, the bibliography accompanying this paper was compiled and studied. It appears from an examination of the careful scientific work performed by the ablest French, German, and English chemists during the last 25 years that they are unanimous in assigning the principal-in fact, the overwhelmingly predominant-cause of the destruction of vegetation to sulphur oxides, resulting either from direct- oxidation of sulphur in oil of vitriol works, etc., or from the oxidation of the sulphur from the minerals associated with commercial coal. Schröder and Schertel showed in 1884 that the sulphates deposited upon the leaves are not injurious to the plants; and Freytag proved that free sulphuric acid could not be found

May 1, 1907

By AIME AIME

AT the annual .meeting of the Minnesota Section in December, Dr. Leith characterized as a question still open the exact method of origin of Lake Superior iron ores and emphasized it as an important practical problem for the future. He welcomed the step taken last year by Dr. Gruner in presenting a new hypothesis, and asked Lake Superior geologists to meet the challenge of such multiple hypotheses by unbiased, study.

Jan 1, 1932

By J. E. Harris

The metallic elements, beryllium, calcium, cerium, lithium, manganese, titanium, vanadium and zirconium are used in metallurgical practice in relatively small percentages for the purpose of improving the physical properties of various alloys. No important uses for any of these elements have thus far been developed either in the pure form or in alloys of which they constitute the major constituent.

Jan 1, 1935

By Lawrence F. Rooney

One of Edgar Allan Poe's stories that haunts my subconscious is the Masque of the Red Death. These days, whenever I join a group like this, especially during the cocktail parties, I see myself and others as those mythical swingers seemingly isolated from the plague. The world, but this country especially, has had a ball plundering, spending, and wasting its natural resources for 100 years. And, as in days of yore, it is fitting that we end this ball with spectacular fireworks: trips to the moon, so that our grandchildren, huddled in their caves along the Ohio, will better understand how it all began.

Jan 1, 1970

By AIME AIME

THE Board of Directors of the Institute has authorized the appointment of a committee to draw up rules of procedure under which awards can be made from time to time to petroleum engineers for outstanding contributions to the art of finding and producing oil and gas. These awards will 11e sponsored by the Petroleum Division and are the first recognition by any professional society of outstanding achievement in "oil mining." They will be in the form of either a gold medal, scholar- ship, or other suitable prize. The awards will be financed from the income of the Anthony F. Lucas Memorial Fund, which was started about fifteen years ago, shortly after' his death, by admirers of Captain Lucas.

Jan 1, 1936

By John Freeman

THE tensile properties of steels at elevated temperatures have been studied by numerous investigators,1 primarily for the purpose of determining their suitability for structural uses. Tests with this objective have been confined largely to the temperature range of approximately 20° to 500° C., because of the rapidly decreasing tensile strength at the latter temperature. Tests have also been extended to higher temperatures for the purpose of determining the most suitable forging range. This temperature range is also of theoretical interest. The phenomenon of increased tensile strength and decreased ductility in the so-called "blue-heat" range, approximately 200° to 300° C., is well known. It was suggested to the Bureau early in 1926 that a study of the properties of rail steels in this temperature range might prove of interest in relation to the studies of transverse-fissure failures in rails. There were available from another investigation3 several new rails from several different heats made to approximately the same specification requirements, the complete manufacturing histories of which were known. It was decided to determine, at least in the preliminary series of tests, only the ultimate tensile strength, elongation and reduction of area, because of the difficulty, time and cost involved in determining the proportional limit and yield point at elevated temperatures.

Jan 1, 1930

By Herbert K. Kutter

This paper is concerned with the physical phenomena in the fracture process of presplitting and only indirectly with the establishment of the optimum presplitting parameters. Its nature is therefore qualitative, rather than quantitative.

Jan 1, 1968