Search Documents

By Ivan César Lopes Diniz, César Romero Afonso Goulart Júnior

Mandrels are tools applied to manufacturing seamless tubes. In VSB plants (Vallourec Soluções Tubulares do Brasil), it is used in two mills. Mandrel and PQF Mills. This is an expensive tool due its alloy (hot work tool steel – AISI H13) and lengh (between 12 meters and 22,5 meters). An opportunity to apply mandrels from PQF in Mandrel Mill has been identified. However, mechanical properties of PQF mandrels must be improved. This work presents the heat treatment process of Quenching and Tempering developed internally at VSB to improve PQF mandrel properties aiming to achieve Mandrel Mill requirements. Hardness and metallography tests were performed before and after some steps of the heat treatment to characterize and validate the process.

Oct 5, 2019

By Alim Ullah

The paper discusses the necessity of upgrading low-iron containing ores, giving as an example, NML-Tata Steel Project in the Quebec-Labrador region of Canada. As cooling of pellets is generally a bottle-neck in most pelletizing plants, examples are given of the methods used to improve cooling in the existing plants and a simple, low-cost alternative, tested on a pot-grate system, is presented. The procedure described is applicable to sinter plants also. The trends in iron and steel production worldwide are then given, as well as the reasons for the increase in steel production by the Electric Arc Furnace (EAF) route. The stoichiometric and thermodynamic requirements for producing iron, irrespective of the process, are explained. The different ironmaking processes, especially the Direct Reduction (DR) ones are briefly discussed, outlining recent improvements made to some of them. The pros and cons of producing cooled DRI and Hot-Briquetted Iron (HBI) are given with predictions made for their future growth. An alternative to cold-briquetting of DRI fines is also discussed. Highlights of an ironmaking processes which is at the laboratory/pilot plant stage are given.

Aug 1, 2018

By Leszek Maldzinski

The present concept assumes carrying out the process of controlled nitriding with NH3 alone. This is a simpler process than that using two-component mixes of ammonia diluted with N2 or NH3diss. The regulation of the chemical composition of the atmosphere in the retort, and therefore the regulation of the nitriding potential KN, is obtained through the variation of the inflow rate of NH3 into the retort. What is a completely new things in a relevant process, the inflow of NH3 into the furnace is at times reduced to zero, which widens the range of the gas composition in the retort (and by the same token, of KN). The amount of NH3 introduced into the furnace is regulated (controlled) with the aid of a gas analyzer (for example an infrared analyzer). The gas analyzer opens and closes periodically the NH3 inlet valve with a frequency maintaining a desired gas composition (a desired KN) in the retort. The concept was based on experimental and theoretical investigations in term of thermodynamic and kinetic of gas nitriding. Investigations were carried out in a laboratory furnace with a quartz tube and also in an industrial furnace with a steel retort and a circulating fan. Nitriding was performed using NH3, NH3+H2, NH3+NH3diss. mixtures. In an industrial furnace the supply of NH3 into the retort was periodically closed, though with an operating circulation fan. The studies demonstrated that the growth rate of nitrided layer depends only on the composition of the atmosphere, (or KN), in the retort. It depends neither on a type of atmosphere introduced into furnace (NH3, NH3+NH3diss. or NH3+H2) nor a type of furnace (laboratory with a quartz tube or industrial with steel retort and fan). The results proved also that entirely closing of NH3 supply to the retort does not affect the growth rate of nitrided layer. A detailed analyses of the results was performed in a paper.

Aug 16, 2017

By Rainer Fackert

3D-Measurements for slabs and heavy plate are now available and close the gap in the production chain. The measuring systems described in this presentation must be seen as high-tech solutions in the field of casting and rolling technology. The measuring systems were developed taking into consideration the harsh casting and rolling mill environment in which they are to be used, with the aim of achieving high operational reliability and eliminating disturbances. Interconnected quality management systems enable optimization across the complete production process. New limits are being defined constantly for all these developments. What is technically feasible today becomes normal practice tomorrow, and will probably be replaced by completely new technologies the day after.

Aug 16, 2017

By Jörg Schwelberger

Government regulations around the world concerning environmental care are becoming more stringent, also including regulations and restrictions of depositing and use of dust, sludge and slag generated in the iron and steelmaking process. With this scenario, by-products such as iron containing dust, sludge, oxide fines, mill scales and slag, become a valuable resource and recycling may be a profitable activity within a plant. Up to ten percent in mass of the total steel output of dust, sludge and mill scale by-product materials and more than 40% of slag by product are generated within an integrated steel plant with an iron content ranging from 50% to 65% for fines and up to 25% for BOF-slag. Slags are being widely recycled and used in the cement industry, as is the case for BF slag, and in the construction industry in the case of BOF slags and EAF slags. However, value of BOF unmodified slag is typically low and environmental regulations limit the usage of the unmodified BOF slag. This paper describes innovative solutions for recycling of fines using cold briquetting technology and the modification and granulation of slag from steelmaking that increase the value of the by-product and yield a marketable product.

Aug 16, 2017

By Peter Fajfa, Heinz Palkowski, Jakob Kraner, Matjaž Godec

The study of asymmetric rolling on the AA 5454 aluminium alloy plates was carried out. The plates were taken directly from the industrial hot rolled sheet. They were cold rolled on the laboratory mill with different rotation speed of the upper and the lower work roller with the strains around 33 % and 44 %. To get closer to the industrial conditions the maximal dimensions of the rolled plates for laboratory rolling mill and the special industrial lubricant were used. After deformation the plates were annealed to the soft condition. This research was focused on all possible effects of asymmetric rolling: The reduction of rolling force, the increase of strain at same set roll gap, bending of workpiece, finer microstructure, more heterogeneous textures and as a consequence of that better mechanical properties. The asymmetric rolling with favourable mechanisms in the deformation zone has created the material with the homogeneous hardness in the cross section and with lower anisotropy, which is crucial for improvement of formability properties of aluminium work hardened alloys and to get closer to properties of steels. In the presented paper the general impact and different effects of speed difference of rollers was investigated on cold rolled aluminium alloy. Obtained and analysed results explain the function of asymmetry in rolling process and the options to implement the asymmetric rolling in industrial plant.

Oct 1, 2019

By Rafael Abreu Fraga, Carlos Noberto Paula da Silva, Emanuelle Garcia Reis, Daniel Bojikian Matsubara

Since 2016 Gerdau Ouro Branco has been producing steel plates of various qualities and grades. However, it was not until 2018 that the first plates produced by accelerated cooling process were made available for external testing, in this case for large diameter UOE pipes manufacturing. Recent line pipe and OCTG specifications are showing that the oil and gas market still consumes regular API grades, such as X60, X65 and X70, however with increasing wall thicknesses, reaching values up to 1.5 inches. These specifications also demand longitudinal and transverse tensile guarantees and drop weight tear tests in temperatures as low as -40°C. Projects with these types of mechanical properties present process requirements as challenging as those necessary for higher API grades in lower thicknesses. This paper shows the steel design concepts and rolling routes for achieving the necessary properties for X70 steel plates in 28.15 mm. The microstructural features were also investigated and associated with the production process and the tensile and toughness results. Finally, challenges such as tensile anisotropy and DWTT abnormal fracture are presented.

Oct 1, 2019

By Adriane Lopes Mougo

Super duplex stainless steel presents a biphasic structure composed by ferrite and austenite with different characteristics and properties. In the micromilling process the cutting edge radius has similar dimensions to the grain size. The biphasic structure found in this material could influence on the cutting tool life and the surface integrity of the workpiece. Due to its low machinability, caused by high hardening level and low thermal conductivity, the process can produce built-up edge and high surface roughness (Ra). In this work it is performed an experimental study of the micromilling of super duplex UNS 32750 and the influence of the cutting speed (Vc) and feed per tooth (fz) on the surface integrity and tool wear. The design of experiments considered two levels and three replicates. Results indicate the increase of roughness for bigger feed per tooth, small influence of the cutting parameters on the burr formation. The tool presented flank wear after the experiments.

Aug 8, 2018

By George Schipper, Peter Gelten, Pepijn Adriaen, Hugo Uijtdebroeks

Tata Steel IJmuiden Hot Strip Mill 2 (HSM2, 5.5 Mtonnes/yr) is currently being upgraded, resulting in an increased rolling force and motor power capacity. With the current conventional work roll spray cooling, a deterioration in work roll & strip surface quality performance is expected as a result of the increased mill capacities. In order to improve strip surface quality, HSM2 decided to do a full-scale production trial with High Turbulence Roll Cooling (HTRC) at stand FM2. HTRC is a novel way of roll cooling using a high turbulent flow regime. HTRC is positioned very close to the roll surface and gap exit, which is beneficial for the roll surface quality. It is operated at a high flow rate but at a low pressure. HTRC not only significantly improves the roll surface quality, in addition, it makes high pressure pumps, needed for the conventional spray cooling, redundant, leading to substantial savings on electricity costs and thus CO2 emissions. HTRC is in trial operation since 7 August 2018. Results show no operational issues, an excellent roll surface quality and an increased cooling efficiency. In summer 2020 stands FM1-FM2-FM3-FM4 of HSM2 will be equipped with HTRC.

Oct 1, 2019

By Michaela Böberl

State of the art sinter coolers are working based on the cross flow cooling principle. Thus, only a part of the thermal energy can be used for heat recovery application. The other part of the cooling air is brought unused to the environment. Furthermore, environmental regulation regarding dust emission and intelligent usage of exergy are getting stronger. Therefore, Primetals Technologies developed sinter coolers based on the counter flow principle. The cooling air passes the sinter bed in counter-flow direction enabling a direct heat transfer from the hot sinter to the air. The exhaust gas temperature can be maximized by using the total heat of the hot sinter. Due to the possible usage of the total exhaust gas amount, diffusive dust emission is reduced to zero. Two types of counter flow coolers are in the portfolio of Primetals Technologies. One type is based on a stationary shaft, in which the hot sinter is charged. The flow of the hot sinter is in vertical direction from top to bottom, in counter direction than the cooling air. The second type is a circular hopper cooler. The hot sinter is charged on top of a moving bed. At the bottom of the bed the sinter is discharged. The cooling air flows also from the bottom to the top, following the counter flow principle. Depending on the requirements, one of the two counter flow cooler types can be chosen for optimized and efficient cooling of hot sinter..

Oct 30, 2017

By Mario Andres Albuja Ribadeneira

El presente trabajo pretende encontrar la ruta para incrementar la productividad y reducir el costo de transformación en una acería eléctrica, mediante el uso de la tecnología disponible en el mercado. El método para alcanzar los resultados se enfocan en una drástica reducción de los tiempos de transformador conectado (power-on), los tiempos de transformador apagado (power-off) asi como la reducción en los consumos de las materias primas e insumos para la fabricación de acero por la ruta del horno eléctrico. La experiencia de Adelca arroja resultados que sobrepasan el 100% de productividad y 30% de reducción en el costo de transformación de la palanquilla. Los resultados obtenidos sin duda alguna servirán de una guía probada para quienes buscan un mejor desempeño en el negocio del acero.

Aug 16, 2017

By Álvaro Lúcio

This paper outlines the DPC process as na economic and environment friendly option for the use of cultivated forest as a source of raw material for metallurgical charcoal.The DPC process was specially developed to bring logistic, environmental, technical, economic and global energy efficiency when compared to termal1 the existing biomass carbonization process. The DPC process utilizes the volatile materials (condensable and non condensable) as a source of the energy required by the carbonization process guarantying its complete combustion. As result the DPC process avoids the burning of termal1 the loaded wood, obtaining a higher charcoal to biomass yield, and avoids the emission to the atmosphere of polluting gases. Gases emitted by the carbonizing wood have na energy termal1e enough to dry the wood soon after its harvesting. By avoiding the storage in the field during na average of 150 days, the resulting economy is quite significant. As a termal1e1 the higher charcoal to biomass yield na termal1e1e economy is obtained through the reduction of the cultivated forest term. This paper emphasizes the economic advantages of the DPC process.

Aug 16, 2017

By Ron Webber

With the difficult economic challenges currently facing the steel industry, it is essential to perform a complete analysis when determining which rolls to purchase. A properly designed “Total Cost of Ownership” model can result in significant savings. This paper will review the costs associated with rolls in both Hot Strip and Cold Strip Mills. The multitude of factors that must be considered in performing a complete analysis for the roll purchasing process will be discussed. Models for both Hot Strip and Cold Mills will be presented. Examples where traditional analysis can lead to expensive, incorrect decisions will be presented.

Oct 30, 2017

By Breno Totti Maia

In these hard days for Brazil steel market, all steel shops want to achieve the same goal, work with: productivity, low costs and high performance. In this scenario the Slagless® technology (which is applied into BOF converter) was important to reach these targets. After use has been reduced the number of times of tip exchange in more than 04 times. Was reduced too, the time to remove lance skulls. Lance keeps clean during all his life with record number of the life 1255 .Blow keep stable due strong measure control at the nozzles and more improvements are planning.

Oct 30, 2017

By Delciane Porfiro, Tiago de Mattos Serodre, Antônio Eduardo Clark Peres, Valdirene Gonzaga de Resende

The evaluation of the effect of the addition of carbon nanotubes (NTCs) directly to a etheramine on the flotation recovery of the quartz at pH 10.5 was carried out by means of microflotation tests in Hallimond tube. The quartz flotation was evaluated using 0.1% (w/v) etheramine solution with different percentages of carboxylic functionalized NTCs. The increase in the percentage of functionalized NTCs increased the flotation recovery to a maximum and from this it was observed a reduction of the recovery of the mineral. Pure etheramine and etheramine with the NTCs were characterized by FTIR spectroscopy and thermal analysis. FTIR spectra of both pure etheramine and etheramine with NTCs clearly showed peaks with the same wavelengths and diagnostics of the cation etheramine and acetate anion. Thermogravimetry indicated that the etheramine + NTCs-COOH mixture lost approximately the same weight percentage over a larger temperature range. In addition, the interaction of the nanotubes with the etheramine caused them to decompose at a lower temperature.

Oct 3, 2019

By Henara Lillian Costa

This paper aims to investigate the effects of a possible incorporation of ethanol to the lubricant during engine use on friction and lubricant film thickness, by adding small amounts of ethanol to Group I base (with and without an organic friction modifier) and to formulated oils. Film thickness was measured using ultrathin film interferometry. Friction tests were carried out using a mini-traction machine to obtain Stribeck curves. The film thickness measurements showed that in the region of low speeds, where the elastohydrodynamic film is very thin and therefore boundary lubrication may prevail, the addition of ethanol produced some boundary film, which was not present for the base oils. For the base oil with an organic friction modifier, the presence of ethanol increased the thickness of the low friction boundary film. For the formulated oil, the addition of ethanol reduced film thickness in all lubrication regimes. The friction tests showed some friction reduction due to addition of ethanol to the base oil, in particular at low speeds. For the formulated oil, the addition of ethanol reduced friction at high speeds, which was associated to a reduction in the viscosity of the lubricant, but at low speeds, the presence of ethanol reduced the formation of a boundary layer, increasing friction. For the base oil containing an organic friction modifier, the presence of ethanol increased the range of speeds for which low boundary friction occurred.

Jul 31, 2018

By Lívia Maria Sant’Ana do Prado

Neste trabalho foi avaliado um método alternativo de redução dos óxidos de cobre, a técnica de redução assistida por plasma de hidrogênio em reator de plasma pulsado de corrente continua (cc). O plasma de hidrogênio apresenta como possibilidade a produção de espécies de alto poder redutor, derivadas da molécula de H2 [1], além de produzir majoritariamente, como produto da reação, o vapor de água que não é prejudicial ao meio ambiente [2]. A pesquisa se limita ao estudo da influência da pressão do processo de redução a plasma sobre a redução de pós de óxido de cobre (I) (Cu2O). Os experimentos de redução foram realizados em um reator a plasma pulsado DC, sob fluxos de hidrogênio de 300cm3/min, temperatura de 300°C, tempo de 60 minutos e pressões variáveis de 267, 534, 800 e 1068 Pa. Determinou-se a eficiência da redução através de um balanço de massa e foram feitas as seguintes análises nos produtos da redução: difração de raios-X, microscopia eletrônica de varredura e EDS. Os maiores valores de frações de redução foram obtidos a 800Pa, o que pode estar associado à formação de uma bainha catódica que envolve por completo e de maneira uniforme a superfície das camadas de pó.

Aug 8, 2018

By Maria Auxiliadora Mendes Aguiar

O sistema de flotação de minério de ferro consagrado no Brasil desde 1977 é a flotação catiônica reversa, na qual deprimem-se os minerais-minério de ferro e flota-se a ganga silicática. Em termos de reagentes, o amido é utilizado como depressor de minerais de ferro e a amina como coletor de quartzo e espumante. Teoricamente, espera-se que o aumento da dosagem de amina eleve a flotabilidade do quartzo. Entretanto, a realidade industrial tem mostrado um comportamento contrário. Este fato tem sido explicado pela formação de clatratos - termo utilizado para denominar o composto molecular formado pela adesão das moléculas de amina no interior das moléculas de amido, que resulta na depressão do quartzo. Em laboratório, a avaliação da flotabilidade de minerais puros pode ser feita através de ensaios de microflotação em tubo de Hallimond modificado. O objetivo do presente trabalho é verificar a flotabilidade do quartzo utilizando-se diferentes dosagens de amina e amido. Para isso, ensaios de microflotação em tubo de Hallimond modificado foram realizados em faixa de pH entre 6 e 12. Identificou-se a dosagem de reagentes que favoreceu a formação dos clatratos.

Aug 1, 2018

By Cyro Takano

A degradação durante o processo de redução de minérios de ferro é bastante conhecida pelos fenômenos de crepitação e inchamento. Em aglomerados a frio, auto-redutores utilizando cimento como aglomerante, há também degradação pela decomposição de hidratos que conferem resistência a frio, além de aumentar os vazios deixados pelo consumo do redutor. Outro fenômeno que afeta na velocidade da reação de redução é a formação de escória. Esses aspectos são analisados neste trabalho e principalmente em processos de auto-redução.

Oct 30, 2017

By Klaydison Silva, Maurício Curi Segato, Elves Matiolo, Neymayer Pereira Lima

Flotation is the main concentration process, has been applied with sucess for the removal of quartz on the iron ore industry aiming high quality concentrates. limiting the top size close to 0,300mm and the removal of slimes are fundamental for the efficiency of reverse flotation of quartz. The high consumption of reagents, leading to insufficient particle coverage, and increased foam stability, leading to the difficulty of removal of quartz particles, are the main deleterious effects of the presence of slimes. Recent characterization studies, together with the development of new collector of linear chain, allowed the obtaining of concentrate with SiO2 contents close to 3% with 94% of metallurgical recovery, based on pilot tests carried out on a sample flotation column of the Quadrilátero Ferrífero.

Oct 3, 2019