Search Documents

A laboratory size solvent extraction apparatus has been constructed, which incorp- orates three stages of countercurrent extraction, followed by two stages of counter- current stripping. The model uses a gravity flow system from one stage to another and air lift pumps to recirculate organic and aqueous phases. A novel pump/mixer system is used to transfer solutions from the mixer compartments to the settler compartments. The model has proven valuable in the teaching of solvent extraction principles.

Jan 1, 1999

By F. F. von Glehn

There is no doubt that simulated ventilation networks must be adequately verified before they can be extrapolated and used for predictive purposes. There are two general approaches as to how the verification can be established and these are summarised as follows; The first approach is to measure all individual branches with trailing hoses or barometers to get individual pressure drop and flow per branch and then calculate individual resistance factors for input into the software. The simulator is run, checking that the output makes general sense (check some sensitivities if possible). The network is now considered as verified. The pressure drop to be measured is relatively small and thus it is inherent that the measured set of individual K factors will be imprecise no matter how much care is taken in the measurements and the resultant simulations will inherit the same problem. In the second approach, the network is assembled using estimated (Atkinson) K factors (based on physical features of airway, past experience and catalogued typical K factors). Only the main primary flow rates are measured and hence the relative distribution of the primary ventilation in the main airways is determined (probably about 10 off primary air flow measurements). Main critical pressure differentials at main and booster fans and across critical doors are measured (probably about 6 off primary pressure differential measurements need to be made). The simulator is run and the computer model is used to iterate and select an updated suite of K factors so that the flow balances and pressure differentials are correctly simulated (typically only 2 or 3 iterations are all that is needed). The network is now considered as verified. The pressure differences to be measured will be substantial in absolute terms and can be measured with high precision. Also, because only primary flows are measured, these will generally be measured at higher air speed points and hence improved relative accuracy. This leads to more accurate simulation results. This paper examines the advantages and disadvantages of the two approaches. 1 Background

Jan 1, 2009

Mother Nature controls, technical professionals model and miners decide. Decisions to explore, mine and mill. Mine decisions, mine design, planning and scheduling are subject to the quality of models û geological models, geotechnical models, resource models, density models. The closer these models are to reality, the more accurate the predicted outcome. So why is it we delegate the modelling tasks to the most junior and least experienced people? If we insist on this, we need to support them û to provide them with æexperience acceleratorsÆ. Technical mentoring is the most effective way to provide the right information at the right time. When this information (read skills) is supplied at the right time we can inject experience into the quality of our modelling and into our decision- making processes. The objective of this paper is to share those behaviours and manners that foster relationships and create frameworks for skills and experience transfer. Central to this is an understanding of how adults learn, an understanding of the basic rules of mentoring etiquette, and the three keys to building meaningful mentoring relationships. An understanding of adult learning processes and styles provides a structure within which a mentor can understand the learnerÆs perspective. Understanding the world from the learnerÆs point is critical to selecting the right language to engage, teach and transfer skills. Basic rules of mentoring etiquette like timeliness, respect and trust need to be brought into the consciousness so they can be agreed on and monitored to prevent conflicts in cultural and generational norms between the mentor and the learner.Meaningful relationships hinge on the three behaviours: truly listening, rather than just hearing; understanding the technical issues within the WIIFM (whatÆs in it for me?) question; and facilitative behaviour. Stronger and more meaningful technical mentoring relationships within our industry will bridge the generational gap and ensure we can capture and capitalise on the wealth of grey hair experience and develop an informed group of young decision-makers.

Jan 1, 2006

By R. A. Beall

This paper summarizes the development of a furnace for producing titanium castings. The general problem is outlined and chronological details are given on the construction and operation of four different casting furnaces, all utilizing consumable-electrode arc heating and water-cooled copper crucibles. Of the two methods of pouring, the tilt-pour technique has been more satisfactory than bottom tapping. Mold design, electrode fabrication, and deep-pool production are discussed. INTRODUCTION In the early summer of 1953 the Bureau of Mines was contacted by the Department of the Army through Watertown Arsenal to explore the possibility of conducting research on casting titanium metal. The objective of the program was "to develop a technique for producing formed castings of titanium metal not less than 40 pounds in weight and without introduction of deleterious contamination."

Jan 1, 1956

A concise country-by-country summary of the mineral industry of Africa is presented. Reserves, resources, role of the country in the world mineral supply, and developments in the mineral industries are reviewed. The data on each country are accompanied by a map showing mineral location and transportation facilities.

Jan 1, 1976

By Warren E. Morrison

Stimulated by 4 years of continuous economic growth without inflation, demand for energy in the United States reached an alltime high in 1964. Total value of production of goods and services (gross national product--GNP) for the year was $629 billion, an increase of 6.8 percent from 1963. Allowing for price changes based on 1958 dollars, the gain in real terms was 5 percent. In 1964 the Federal Reserve Board Index of Industrial Production stood at 132, a rise of 6.2 percent. With the impetus provided by personal income and corporate tax reductions during the year, aggregate wages, profits, and consumption reached record levels. Even the persistent balance of payments problem improved. Against this background the national consumption of commercial energy increased 4.2 percent. Energy needs continued to be met largely from domestic resources with imports, mainly crude petroleum and refined petroleum products, accounting for but 7 percent of the total. Mineral energy resources, namely gas, coal, and petroleum, contributed 96 percent of the input of energy into the economy during the year. The remaining 4 percent came from hydropower and nuclear power.

Jan 1, 1965

This manual is limited to Augered Cast-in-Place (ACIP) piles constructed using a hollow stem continuous flight auger. 1.1SCOPE AND LIMITATIONS The intent of this manual is to provide guidelines for observing and documenting the installation of ACIP piles. The manual may also serve as a guide for the training of inspection personnel. It is expected that the general guidelines and procedures described in this manual for the inspection and installation of ACIP piles will be supplemented by engineering judgment, local practice, and experience. ACIP pile construction procedures will vary depending on soil, rock, and groundwater conditions. This manual represents a wide range of possible applications in a variety of projects. It is not intended to be applicable in all situations nor replace engineering judgment for any given project. Therefore, an all-inclusive inspection manual is not considered practical or desirable. This manual should not be used to interpret or replace project specifications. It has, however, been prepared to complement the Augered Cast-in-Place (ACIP) Piles Manual model specification (DFI, 2003).

Jan 1, 2010

By Matthew E. Meyer

The intent of this manual is to provide guidelines for observing and documenting the installation of ACIP piles. The manual may also serve as a guide for the training of inspection personnel. It is expected that the general guidelines and procedures described in this manual for the inspection and installation of ACIP piles will be supplemented by engineering judgment, local practice, and experience. ACIP pile construction procedures will vary depending on soil, rock, and groundwater conditions. This manual represents a wide range of possible applications in a variety of projects. It is not intended to be applicable in all situations nor replace engineering judgment for any given project. Therefore, an all-inclusive inspection manual is not considered practical or desirable. This manual should not be used to interpret or replace project specifications. It has, however, been prepared to complement the Augered Castin- Place (ACIP) Piles Manual model specification (DFI, 2003).

Jan 1, 2010

By Dennis Ofiara, Michael Lewis

An experimental 1.75 meter Shaft Boring Machine was designed and manufactured by The Robbins Company. The drill was used by contractor Drillcon Raise AB to drill test shafts at an SKB underground test facility. SKB is the Swedish authority responsible for safe management of nuclear waste materials. This “SBM1.8” Shaft Boring Machine was used to drill shallow test shafts ingranitic rock at SKB’s Aspo underground laboratory. The drill used a unique vacuum mucking system. The bored shafts were held to very strict tolerances for bore diameter, straightness, and verticality. This drill was launched and operated from a mobile launcher. Headroom and working space were limited. The SBM1.8 drill produced acceptable test holes. SKB will carry out several studies to determine the suitability of this geology, and of this technique, for safe nuclear disposal. In addition to future use at SKB, many applications are foreseen, particularly in the civil construction industry.

Jan 1, 2005

By McNicol M. D

Petroleum exploration in onshore Gippsland was directed in the 1950s and 1960s towards plays in the basal Latrobe and Strzelecki Groups, but these became forgotten in the 1970s with the Latrobe play discoveries offshore. The principal explorationists of the time were Woodside Oil and Arco Ltd, who then departed the scene after drilling some 18 wells without major success. In the late-1980s successful hydrocarbon finds in equivalent age Otway Group sediments in the Otway Basin were made and in early 1990 Tyers Petroleum began investigations into Strzelecki Group prospects as applied to the onshore Gippsland Basin. Some 18 anticlines have been mapped, based on shallower coal exploration drilling in the Latrobe Group, which from seismic and gravity evidence are believed to unconformably overlie similar anticlinal structures in the underlying Strzelecki Group. Strzelecki targets of interest within drilling depth are the basal Tyers Conglomerate/Rintouls Creek Sandstone Formations which outcrop in the north of the Latrobe Valley and are analogous to the Pretty Hill Sandstone in the Otway Basin. In addition, intra-Strzelecki Group targets similar to Heathfield and Windermere Sandstone Members are also considered to be present. Good source rocks are abundant including coal seams and carbonaceous sediments of Neocomian and Jurassic age, which lie within the oil window. Seal is provided by the overlying Aptian-Albian aged volcanogenic sediments. The Tyers/Rintouls sandstones - a target in the Woodside/Arco wells, with two exceptions, were not reached. Encouraging intra-Strzelecki shows were reported in many of the wells. Basal and intra-Strzelecki porous quartzose sandstones remain one of the few untested plays left in the Gippsland Basin and, in the onshore, merit extra attention as they he within the oil window at economically drillable depths.

Jan 1, 1992

Due to the reduction in frictional resistance, the characteristics of joint infill have a major role to play on rock mass instability. This paper elucidates the laboratory behaviour of graphite infilled joints based on a large-scale shear apparatus under constant normal stiffness (CNS). Discontinuities in a graphite mine have been simulated using high strength gypsum plaster, with the joints infilled with compressed graphite layers. The Fourier series was employed to characterize the joint surface, and the method of using the Fourier coefficients for the prediction of dilation and normal stress with displacement is explained. Die Charateristik von Verbindungsfüllungen hat einen wichtigen Einfluss auf Felsmassenstabilität aufgrund der Verringerung des Reibwiderstandes. Diese Veröffentlichung untersucht das Verhalten von Graphit gefüllten Verbindungen im Labormaßstab mit einer Methode die auf einem gross-umfang Apparateprinzip unter konstanter Normal-Steifheit beruht. Unregelmässigkeiten in einer Graphit Mine wurden mit Gypsum Gips von hoher Festigkeit simuliert, die Verbindungen wurden mit kompressierten Graphitschichten gefüllt. Fourier Reihen wurden angewandt um die Verbindungs Fläche zu Characterisieren. Die Methode die verwendet wurde um die Ausdehnung und Normalkraft mit der Verschiebung mit Hilfe von Fourierkoeffizienten zu bestimmen wird beschrieben. Due à diminution des résistances par frottements, les caractéristiques des joints de remplissage joue un rôle majeur sur les instabilités de la roche. Cet article étudie le comportement en laboratoire des joints de remplissage en graphite à partir d’un dispositif de friction à grande échelle sous rigidité normale constante. Les discontinuités dans une mine de graphite ont été simulées grâce à un plâtre à haute teneur en gypse, dont les joints ont été remplis de couches de graphite compressées. La caractérisation de la surface des joints a été réalisée avec les séries de Fourier. La méthode utilisant le coefficient de Fourrier pour la prédiction de la dilatation et de la compression en fonction du déplacement est également expliquée.

Jan 1, 2003

By G. S. Scott

In the course of the investigation into the causes, behavior, and control of mine fires, which the Bureau of Mines is now conducting, some attention was given to the subject of spontaneous heating. It is self-evident that the temperature of a pile of broken coal will rice if the rate of generation of heat exceeds the rate of brat dissipation and will fall if the opposite is the case. Factors that affect the rate of generation of heat are:

Jan 1, 1941

By Maxwell Gensamer

Jan 1, 1960

An extensive laboratory grinding study was carried out on a magnetite ore in order to assess the grinding behaviour of magnetic concentrate and tail from low intensity magnetic separation (LIMS).The test work involved Bond ball mill testing, rod milling, low intensity magnetic separation (LIMS), and batch ball milling down to product sizes of around P80~25 microns. A total of 18 Bond tests and over 150 batch grinding tests and sieve sizing were carried out. Throughout the grinding tests, power draw was continuously monitored. The relationship between the grinding energy and product size was analysed using the conventional energy-size concepts. It was found that the Rittinger equation fits the experimental data well. However, Bond?s equation does not fit the experimental data well, and therefore a modified Bond equation was developed. Differences in grinding properties between the magnetic and non-magnetic component were analysed and compared to the bulk ore. It was found that grinding properties differ significantly and therefore separate grinding test work may be required for each grinding step in the magnetite ore beneficiation flowsheet. Keywords: grinding, iron ores, particle size, modelling.

Jan 1, 2010

By Najdat I. Aziz

There are different schools of thoughts about the influence of gas pressure on coal strength. Researchers have reached contradictory results with regard to the effect of confining gas pressure on tensile strength of coal. Accordingly, this paper re-examines the influence of gas pressure on the strength of coal. A specially designed precision drill capable of drilling in a pressurised chamber was used to drill coal samples under both atmospheric and increased gas pressure environment. The drill cuttings were examined for particle size distribution using a laser controlled Malvern Mastersizer S particle size analyser. Petrographic analysis of the sample examined the effect of gas pressures on the maceral structure and the composition of coal. The paper demonstrates that there is a definite variation in the range of particle size distribution with particles obtained from drilling coal samples not subjected to gas pressures, in comparison with those obtained from samples drilled under confined gas pressure. Also observed were the changes in the rate of drilling in soft coal obtained from geologically-disturbed zones compared with other coal samples. Some variation on the maceral compostion of coals were also observed in relation to increased gas pressures and gas type.

Jan 1, 1996

By C. W. Whitten

Iron ore deposits in south-central Missouri have emerged as a possible resource for the rare-earth elements. The Pea Ridge Iron Mine is one such deposit. Rare-earth minerals at the Pea Ridge Iron Mine are contained in breccia pipes consisting primarily of silicon oxides and feldspars. These pipes extend up through the magnetite ore body and appear to be alterations and replacement of earlier hematite. The mineralogy of these pipes is very complex and varied, which could complicate the concentration and extraction of the rare-earth minerals. This U.S. Bureau of Mines !eport represents a study by characterization of the mineral phases to assess the amenability and development of concentration and extraction techniques. Previous characterization of rare-earth minerals has been mainly by transmitted light microscopy. This method along with reflected light microscopy, scanning electron microscopy, and X-ray diffraction was used to identify and characterize the rare-earth and associated minerals. The minerals identified were the major ore minerals, magnetite and hematite; the rare-earth phosphates, monazite and xenotime; the rare-earth silicate, allanite; the minor associated minerals, cassiterite, pyrite, and apatite; and the gangue minerals, feldspar, quartz, and actinolite.

Jan 1, 1990

By Charles Steed

The design of pillars in room and pillar operations is always a compromise between factor of safety and ore recovery. In actively mined and accessed areas the stability of pillars must be sufficient to support the roof, providing safe working conditions for men and equipment, while optimizing ore recovery. As a reserve is mined out, and if conditions are favourable, pillars are often removed to increase recovery. Considerations for pillar removal include value of the ore, the effect on immediate and overall mine stability and the safety of the mining operations as well as the consequence of disruption of overlying strata and surface infrastructure as the support of the pillars are removed. Many parameters influence pillar strength and the contribution of the pillar to ground support. These include seam height, seam depth, seam inclination, room span, quality of rock, time, etc.. Empirical, analytical and numerical modeling methods are commonly used to optimize pillar sizing and placement and predict influence of pillar extraction or reduction on ground stability. Practical examples for pillar design and optimization in low seam gypsum mining operations and optimizing sequencing of pillar extraction in thick seam metal mining operations are outlined.

Jan 1, 2003

By T. G. Chapman

This paper has been abstracted from a forthcoming Bureau of Mines bulletin on the concentration of copper ores in North America. GENERAL DEVELOPMENTS IN CONCENTRATING COPPER ORES FROM 1912 TO 1932 During the east 20 years the milling of copper ores as practiced in the larger concentrators has chanced to such an extent that comparatively few of the machines in use at the beginning of this period remain in service today. Concentrating Practice in 1912. In 1912 the usual equipment for concentrating copper ores comprised jigs for the coarser sizes, tables and sand vanners for the intermediate sizes, and vanners for the finer crushed and ground material. Rolls operated in series under graded crushing conditions, were in common use for the liberation of the copper minerals; grinding by Chilean or Muntington mills ordinarily was confined to the coarser tailings of jigs and tables.

Jan 1, 1934

By D David

Amongst those whose task it is to design tumbling mills and other comminution machines there is an almost religious divide between devotees of the Bond method and devotees of other methods developed in more recent times. For a decade or so the issue was between the Bond power-based methods and the JKMRC (JK) simulation based approach. The newest method to challenge the status quo is power-based and was developed by Steve Morrell. As the title suggests, this paper will take some liberty at concluding that Fred Bond and Steve Morrell may be separated by history, but not by their approaches to their individual contributions to the science of comminution. Another driver for the paper is that although it is good to have diversity of thought, the existing divisions are problematic for those of us signing public disclosure documents. If alternative design methods produce materially different outcomes for the mill duty, then at least one of them is wrong or being used incorrectly. At some point the unsustainable argument may need to be put in a court of law that we metallurgists have two or more materially different design methods, each of which is correct! Therefore, perhaps a resolution is needed before this occurs?The works of both Fred Bond and Steve Morrell are each directly related to their contemporary grinding mill design and operational environments. Both their approaches are empirical, borne of observing and measuring real world situations. Both worked with theories that preceded them, gathered their own data and then each saw shortfalls in the status quo.Fred Bond was an escapee from revolution, a victim of The Great Depression, and had several near death experiences during his early site-based career. Perhaps he was fortuitously rescued from himself when asked by Allis Chalmers (A-C) to set up its rock testing laboratory in Milwaukie in 1930. Fred’s testing led him to conclude that neither the Kick nor the Von Rittinger theories explained his measurements. His writings on the failings of these old theories caused a divide between devotees of the old and new methods at that time. After many years, and much thought and plotting of data (the old way!), he came up with his now-famous equations (and his Third Theory) which have stood the test of time, certainly in the world of Bond-era machines.Coming from England via several African diamond mines, Steve Morrell immersed himself into the comminution world of the JK in Brisbane about a decade after Fred passed on. The JK had developed its semi-autogenous grinding (SAG) simulation framework using its own pendulum breakage tester, itself a derivative of the twin pendulum impact device invented by Bond decades earlier. At the JK Steve developed his authoritative Tumbling Mill Power equations and was involved in real world analysis of comminution problems on the global stage. Steve’s JK experience coincided with the demise of the rod mill, the rise of autogenous grinding (AG) and SAG milling and a rapid expansion in concentrator capacity.Morrell left the JK to pursue his own interests, which included ongoing consulting work, now demanded by the comminution world. He then turned to investigating a growing list of discrepancies between the opinions of designers and theoreticians, and the factual outcomes. The Morrell Method of design arose from this re-examination of ore testing, real world operating data and these glaring and expensive discrepancies between design and outcome. The elements necessary for a relook at the world of rock breakage were in place!CITATION:David, D, 2017. Steve and Fred would have been mates – a comminution design evolution story, in Proceedings MetPlant 2017, pp 2–11 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

A pyrite flotation concentrate assaying 0·065 oz/ton gold was investigated to determine the mode of occurrence of the gold. Ftom cyanidation and acid leaching experiments it was concluded that O· 02-0· 03 oz/ton goldwas in solid solution in pyrite and the balance of the gold was finely dispersed as grains throughout the pyrite.Autoradiography and electron-probe examination of possible areas in briquetted concentrate did not detect any grains of gold. Neutron irradiation and gamma spectrometry confirmed on 100 mg samples the fire assays obtained on 1 assay ton samples.Oxidation to hematite and reduction to magnetite at 600°C made practically the whole of the gold extractable by cyanide. This technique could be of major significance for gold ores which contain a substantial amount of "refractory" gold.

Jan 1, 1969