Search Documents

By Katsuyoshi Kondoh

The synthesis processing of Mg2Si or Mg2SiIMgO at lower temperature from the elemental magnesium alloy powder/chips and Si or SiO2 powder mixture was established via the repeated plastic working (RPW) based on Powder Metallurgy (PIM) process. RPW is much effective on the mechanical breakage of MgO surface films, which prevent from the solid-state reaction between Mg and Si powder. The solid-state synthesized Mg2Si particle of 200nm-2um is extremely fine, compared to that via the conventional casting process, causing the coarse one of 50-100um. This is because of not coarsening during the solid-state synthesis of Mg2Si. By using in-situ fonning process of Mg2Si via RPW and pre-heating before hot working such as extrusion and forging, the magnesium composite material with Mg2Si or Mg2Si/MgO dispersions was developed in employing Si or SiO2 particles, respectively. For example, when employing AZ31 chips as raw materials of the matrix, it has low density of 1.85g/cm3 and extremely superior mechanical properties, such as tensile strength over 350MPa with 5-10% elongation and Young's modulus of 47-50GPa, to the conventional Mg-Al-Zn alloys. The Mg composite alloy wires and pipes were produced via the hot extrusion process in the manufacturing plant, and also showed excellent mechanical properties.

Jan 1, 2003

By Milton Manrique

The thermal decomposition of zircon concentrates in a non-transferred arc thermal plasma flow reactor was investigated. The plasma torch was operated using argon-helium and argon-nitrogen mixtures as plasma gases. The effect of power, feed rate and zircon particle size was studied. Products were characterized by XRD, SEM, TEM and chemical analytical techniques. The average size of the product was in the submicron range. Free energy minimization plots were used to predict the behavior of the system under different operating conditions. A kinetic model to describe the different stages of the thermal decomposition process is proposed. The results of this investigation showed a significant segregation process where the zirconia-rich product is collected in the reactor while the silica-rich product is collected in the filter. TEM analysis indicated that silica vapor is condensed on the surface of the zirconia particles.

Jan 1, 1996

By H. Y. Sohn, S. PalDey

"A new chemical synthesis process for the preparation of intermetallic compounds has been developed. It involves the vapor-phase reduction of mixtures of constituent metal chlorides by magnesium vapor to produce intermetallic compounds in the form of fine powder. The advantages of the process include (a) the use of inexpensive raw materials, (b) low reaction temperatures, and (c) products in the form of fine particles. Titanium and nickel aluminides were prepared by this method. The effect of AlCl/TiCl3 partial pressure ratio on the formation of different titanium aluminides was studied. A two-phase mixture containing 80 mol % of TiAl and 20 mol % of TiA13 formed at an AlC13/TiC13 ratio of 10. The amount of TiA13 was maximized to 72 mol% at an AlC13/TiC13 ratio of 16. The maximum conversion of the limiting chloride TiCl3 was 94 % . In the case of nickel aluminides, NiAI, NiAl3, and Ni2Al3 were formed by reducing mixtures of NiC12 and A1Cl3 vapors. The effect of the partial pressure ratios AlCl3/NiC12 and Mg/NiC12 on the formation of nickel aluminides was studied. The maximum content of NiAl obtained was 98 mol % . At the AlC13/NiC12 ratio of 19, a two-phase mixture of 17 mol% of NiAl and 83 mol% of NiA13 was produced. The product particles were very fine in the size range of 0.05 to 0.2 µm.A. IntroductionIntermetallic compounds are attracting much attention [1]. Titanium and nickel aluminides have attracted a great deal of attention from the aerospace as well as automobile industries because of their potential for high-temperature application (e.g., low density, good oxidation resistance, and high-temperature strength retention [2, 3]). Gamma TiAl and two-phase (TiAl and Ti3Al) alloys [4] are used for gas turbine engine rotational components as well as automobile exhaust valves. TiAl3 is one of the most extensively investigated aluminum-rich intermetallics. Nickel aluminides are attractive because of their low densities, relatively high melting point and good high-temperature strength properties. For example, Ni3Al shows increasing rather than decreasing yield strength with increasing temperature [5]."

Jan 1, 1998

By N. J. Themelis

In the last two decades, the Outokumpu flash smelting process has become the dominant new technology for copper smelting and has? also been applied to the smelting of other metal sulfides. The application of oxygen enrichment and improvements in concentrate burner and furnace design have resulted in ever increasing smelting rates per unit volume of the reaction shaft. This paper examines the. rate phenomena taking place in the reaction shaft of the Outokumpu furnace and compares information obtained from a mathematical model of heat and mass transfer rates to results obtained in pi1ot tests conducted at Pori, Finland, and to actual performance of a number of flash smelters around the world. 2?

Jan 1, 1985

By D. I. Davidov, D. A. Shishkin, M. B. Rigmant, E. P. Romanov, N. N. Stepanova, N. V. Kazantseva

The Co-19 at.%Al-6 at.%W alloy was prepared by two methods of casting. We used arc melting under an argon atmosphere with casting into a copper water-cooled casting mold and induction melting furnace with casting into a ceramic Al2O3 mold. According to the X-ray and SEM analyses, phase compositions depend on the cooling rate of the ingot after melting. After arc melting, the cast alloy has a three-phase structure, consisting of  cobalt (FCC), intermetallic phases CoAl (B2) type, and Co3W (DO19) type. After the induction melting, the alloy has a three-phase structure, consisting of  cobalt (FCC), intermetallic phases CoAl (B2) type, and Co7W6 () type. All phases in the investigated ternary alloy at the room temperature are ferromagnetic. Curie temperatures of all obtained phases were defined. It is shown that the magnetic properties of the studied alloy are typical for soft magnetic materials.

Jan 1, 2015

By Shengli Wu, Mingyin Kou, Laixin Wang, Zhe Wang, Xinliang Liu

The sticking behavior of iron ores in the shaft furnace is one of the most important problems in the COREX melting progress, which directly influence the smooth operation and productivity of shaft furnace. Therefore, it is of great importance to study the sticking behavior of pellets in COREX shaft furnace. The results showed that porous metallic iron produced at the interface of pellets samples was the main reason for the sticking of pellets in the COREX shaft furnace. The SI (sticking index) and metallization rate increased with the reduction temperature and gas flow, and decreased with melting rate. However, the SI of pellets in the COREX shaft furnace could be decreased by the proper match of melting rate and reduction temperature, reduction temperature and gas flow, while the metallization rate of pellets were kept at a certain level. Furthermore, the matching of melting rate and reduction temperature was more effective than the matching of reduction temperature and gas flow.

Jan 1, 2016

By Minjun Tang, Jianfeng Zhou, Linjiang Qing, Yufeng Guo, Tao Jiang

"For the comprehensive recovery ofV, Ti, Fe in vanadium-titanium magnetite in the process of pre-reduction-electric furnace smelting, it is expected that vanadium oxide is reduced into molten iron and titanium oxide is available in the slag. Thus the effect of slag basicity, the content of MgO, MnO and CaF 2 of slag content on the separation of slag and molten iron and the comprehensive recovery of V, Ti, Fe were investigated. The results show that increasing slag basicity, MgO, MnO and CaF2 are all beneficial to the separation of slag and molten iron. Higher slag basicity and the addition of CaF2 strengthen the reduction of vanadium oxide, and inhibite the reduction of titanium oxide, which are in favour of the recovery ofV and Ti. However, the addition ofMgO, MnO was not efficient for the comprehensive recovery ofV, Ti, Fe. For the vanadium-titanium magnetite of Panxi in China, the recovery of Fe was over 98%, the recovery ofV in molten iron was over 85% and the Ti02 content in slag was about 43% under the optimal conditions of slag phase type.IntroductionIt is well known that there are abundant vanadium-titanium magnetite resources which are located in Panzhihua of Sichuan Province[!]. At present the vananium-titanium magnetite concentrates are smelted in the blast furnace, which just make use of iron and vanadium, but lots of titanium is discarded in the slag. At the same time, the process has a large number of disadvantages, such as low recovery of vanadium, long route, pollutions, large investment and expenditure of energy[2-3]. In recent years, in order to efficiently utilize the vanadium-titanium magnetite concentrates, several new non-blast furnace processes have been proposed, such as pre-reduction-electric furnace, pre-reduction-grinding separation and so on[4]. Especially pre-reduction-electric furnace is operating well in South Africa and New Zealand,However,Du to the high slag basicity of the slag, the grade ofTi02 of slag is Corresponding author:Minjun Tang.E-mail:450435123@qq.com. Tel:13627429224."

Jan 1, 2013

By Jesús Contreras

Since the commencement of its activities in Huelva in 1970, Atlantic Copper has maintained a course of action that has been more demanding than the successive environmental legislations current at different times. As its primary objective it has sought compatibility between the protection of the environment and both its industrial activity and the social and economic development of the area in which its Metallurgical Complex is located. For this reason, since the seventies it has maintained a continuous programme of investments which have allowed it to attain its present environmental situation. As a consequence of the Environmental Policy of Atlantic Copper, in April 1998 it obtained certification for its Integrated System of Environmental Management (SIGMA) according to international standard IS0-14001, and under European Community Regulation 1836/93 (replaced by the 76112001) for the Eco-Management and Eco-Audit System (EMAS). The SIGMA formalises the environmental management practices of Atlantic Copper and engages it to have available a system that can be fully audited. Atlantic Copper was the first European Company in the non-ferrous metallurgical sector to obtain both the UNE-EN-ISO 14001 certification and the EMAS registration. The present paper reviews the actions by Atlantic Copper in environmental matters that have allowed it to achieve its present position. It also describes the coming stages of improvement planned and the modifications to be carried out in the near future, in particular the criteria for the selection of technologies on the basis of the concept of BAT (Best Available Techniques) introduced by the European Union, and always guided by the final objective of converting Atlantic Copper into a reference within the sector, comparable to the best designed and operated installations in the world.

Jan 1, 2003

By J. D. McCain

Magma's San Manuel smelter has adopted new operating techniques resulting in 21% increased productivity and 87% reduction in lost time accidents. Reverberatory furnaces were converted to coal firing from expensive natural gas and fuel oil. Slag and matte flow problems and safety were improved by implementing hydraulic slag stopping and matte tapping machines. Coordination of furnaces, converters and acid plant was improved by using a computer-aided converter controller/scheduler function. Manual mudding of converter lips after each collar pull was replaced with a gunning system for coating the mouth castings. One converter punch car was automated using robotic technology. An automatic anode take-off was installed with fewer moving parts and a mechanism for ear twisting one cell contact. Anode copper refining was improved by replacing propane/hydrogen mixtures with high pressure/velocity natural gas tuyeres. Improved converter scheduling increased acid plant production 43% with more autothermal operation time. Six dedicated computers/microprocessors are utilized for automation, data acquisition, process monitoring and on-line air quality information for the Supplementary Control System.

Jan 1, 1983

By E. A. Werner, A. Pichler, A. Spalek, G. Reisner, P. Stiaszny

"Interstitial free (IF) sheet steels are used for complex shaped parts because of their excellent formability. If a deep drawn part is subjected· to a impact deformation at low temperature brittle fracture of the part may occur. This phenomenon\ is called secondary work embrittlement (SWE). One possibility to characterize this material/structural behavior is the drop-weight test. The result of .this .test is a temperature at and below which a crack can initiated in a deep drawn part under the investigated set of parameters. This paper addresses the influence of the preforming process on the sus- . . ceptibili.ty of IF steels to SWE.IntroductionInterstiiial:free (IF-) steels are frequently used in the automotive industry for complex· shaped p·arts because of their excellent deep drawability. The microstructure of the steel consists of a highly ductile ferritic matrix with embedded precipitates of nitrides and/or carbides. Brittle fracture can occur in deep drawn parts, if they are subjected to a high speed deformation at lo""w temperature. This phenomenon is called ~econdary Work gmbrittlement (SWE) [1-11]. Up to now there are no standardized testing procedures available to quantify the sensibility of IF-sheet steel to SWE. Neveitheless, a reasonable testing procedure which allows to quantify the tendency of a predeformed part to SWE is necessary for further material development. A commonly used test method is the drop-weight test performed at low temperatures. In such ·tests a cone-like drop weight expands a deep drawn cylindrical cup [l-3, 6, 8, 9, 11]. From this expansion experiment the temperature is determined at and below which a brittle crack can be initiated in the deep drawn cup under the investigated impact test parameters. The highest measured temperature at which a deep drawn cup fails by brittle fracture is called frack appearances !emperature (CAPT). The lower the value of the CAPT the lower is the sensibility of a deep drawn part of IF-sheet steel to SWE. This paper aims to clarify the role of the preforming process on the impact behavior of an IF steel. For this purpose a numerical analysis of the deep drawing process and cup expansion tests are conducted."

Jan 1, 2000

By Philip Arthur

The ISASMELT process is making a significant contribution to the global metals industry. ISASMELT furnaces are now operating successfully in eight different countries and treating approximately 3 million tonnes of concentrates and secondary materials per year. The process is currently used in both lead and copper smelting. The most recently commissioned plants were in Germany and China, one for treating scrap copper and the other treating low-grade copper concentrates. The Copper ISASMEL T furnace ("CIF") at Mount Isa Mines Limited ("MIM") has continued to set new operational records, with throughput of more than I million tonnes of concentrate per year and very low operating costs. This paper summarises the latest operational data from the Mount Isa Copper ISASMELT plant and outlines the successful approach to industrial R&D taken by MIM in the development of the ISASMEL T process.

Jan 1, 2003

By Wenzhou Yu, Cong Zhang, Wenhui Ma, Gang Wang, Kuixian Wei

"A novel technique was successfully developed for nickel further purification by vacuum directional solidification. The removal effect of impurities in nickel was studied based on theoretical analysis and experiments. High removal efficiency of impurities in nickel can be realized according to theoretical analysis. The experimental results show that the vacuum directional solidification treatment could increase the nickel purity from 99.96% to 99.996%. Since vacuum directional solidification could effectively remove the impurities from nickel with low contamination and low cost, it is a potential route to obtain high-purity nickel for commercial application.IntroductionNickel is widely used in metallurgy, machinery, petroleum industry, chemical industry, construction industry, light industry, and other industries for its ductility, medium hardness, ferromagnetism and high chemical activity. Nickel-based alloy is an important material for the key parts of aircraft, tanks, submarines, radars, nuclear reactors and aerospace fields [1-5]. Generally, nickel contains Si, P, S, Fe, Cu, Zn, As, Cd, Sn, Sb, Pb, Bi, Al, Mn, Mg and other impurity elements, which may hinder the commercial application of nickel. Therefore, it is necessary to refine the crude nickel for the high purity nickel."

Jan 1, 2014

By Pengfu Tan

A thermodynamic model and computer program, CuModel, has been developed to model the distribution behaviors of Cu, Fe, S, O, Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag, copper loss in the slag, and heat balance in copper smelting process, matte converting process and copper con-tinuous smelting process. It can be predicted for any set of controllable process parameters such as feed composition, smelting temperature, degree of oxygen enrichment and volume of oxy-gen-enriched air. This model accounts for physical entrainment between matte and slag phases. It can be used in Isasmelt process, copper flash smelting process, Mitsubishi process, P-S con-verting process and Noranda process. The predictions by the present computer model are com-pared with the known commercial data from Guixi Smelter in China, PASAR Corporation in Philippines, Horne Smelter in Canada, MIM Limited in Australia and Naoshima Smelter in Ja-pan. The agreements between the computer predictions and the commercial data are excellent. In this paper, the applications of CuModel in the copper metallurgical industries have been pre-sented. CuModel has been used by Daye Smelter and Guixi Smelter in China, and by PASAR in Philippines as well.

Jan 1, 2004

By Kiyoshi Shibata, Jun-ichi Hayashi

"Steel making technology poses strong potentials for environmental protection in three direction. One is pollution control on steel making process itself. Japanese steel industry has cut down various type of emission drastically since 1970's. Secondary, those process technology can be applied to reduce environmental burden in other industrial sectors. One of the successful examples is municipal waste treatment facility. Thirdly, development of high performance steel products, such as high strength steel for automobile body, can contribute to improve environmental performance during their use, based on the concept of life cycle assessment. Some examples of the successful development and future task is discussed.IntroductionsStack and smoke used to be a symbol of energy intensive industry such as steel making. But, scenery of steel works and its surroundings have been completely changed, and steel products have been changing, as well. The steel making industry consumes huge quantities of energy and resources. Variety of technical development have been carried out to reduce the pollutant release. The steel industry in Japan has been making direct and indirect contributions to reducing of various kinds of environmental impacts through development of high-performance process and products: Its potential technical capability accumulated in steel making is fundamental and essential infrastructure for the vein systems of our society. In this paper, the activity of steel making industry for better environment is discussed"

Jan 1, 2000

By Stefan Mutz

In Germany the automobile recycling is regulated by law. Current legislation requires that by the year 2015, eighty five w.-t. % of the components from used cars ill be materially recycled. Whilst for 10 w.-t. % of the materials a thermal utilization is certified, there are still some concrete questions that remain unanswered regarding the usability of single fractions. The recent innovative approaches to the concepts of used cars dismantling do not alter the fact that the majority of the materials of used cars still have to pass over the shredder and the connected processing aggregates. The status of the so called SLF (Shredder light fraction) which is about 25 w.-t. % w.-t. in used cars, has not been satisfactorily clarified. Furthermore questions still remain regarding the separation of the NMSF (nonmagnetic metal shredder fraction) which has to be separated in the single metallic fractions like stainless tell, copper, brass, zinc, etc. Attempts of optimization can be found. This paper analyses some of the difficulties being encountered by the automobile recycling industry in Germany, before reviewing some of the innovative approaches that the industry has introduced. Finally the paper goes on to describe the potential of automatic picking. Examples of a series of tests, utilizing this technology, in which a variety of products from a range of shredders were isolated are described in detail. This new technology provides a range of applications to the automobile recycling industry.

Jan 1, 2002

By Philip Arthur

The ISASMELT process is making a significant contribution to the global metals industry. ISASMELT furnaces are now operating successfully in eight different countries and treating approximately 3 million tonnes of concentrates and secondary materials per year. The process is currently used in both lead and copper smelting. The most recently commissioned plants were in Germany and China, one for treating scrap copper and the other treating low-grade copper concentrates. The Copper ISASMEL T furnace ("CIF") at Mount Isa Mines Limited (UMIM") has continued to set new operational records, with throughput of more than I million tonnes of concentrate per year and very low operating costs. This paper summarises the latest operational data from the Mount Isa Copper ISASMEL T plant and outlines the successful approach to industrial R&D taken by MIM in the development of the ISASMEL T process.

Jan 1, 2003

By T. E. Warner

In order to detect arsenic and antimony in zinc, various electrochemcial experiments were performed involving the electrochemical introduction of sodium atoms into molten zinc using a solid electrolyte. Under high rates, the formation of the intermetallic phase NaZn13 was assumed to form. Under more moderate injection rates of sodium, employing a symmetric "zinc/zinc cell", a qualitative relationship between the current generated during cyclic voltammeuy and the arsenic and antimony concentrations in molten zinc was observed.

Jan 1, 1999

By L. Deininger

The QSL plant in the existing "Betzelius" Stolberg GmbH lead smelter in StolberglGermany was commissioned in August, 1990. Following some modifications to the process and equipment which had become necessary in line with the implementation of this new techno- logy, conclusive operating results are now available. These will be reported together with a short description of the plant design. In May 1992, raw material feeding to the QSL reactor in the new lead smelter of Korea Zinc Co. in OnsanlKorea was started. As all the experience gained up to that point in time in the Stolberg plant had already been incorporated in this plant prior to start-up, it reached stable, satisfactory operating conditions in a short period of time. After an introductory description of the plant important operating results will be reported. The operating experience gained in the two plants fully confirms the correctness of the in- ventors' creative ideas in the 70s. The QSL process meets all demands made on modern, ecologically compatible and energy-saving lead production technology. The paper ends with suggestions on how the QSL process will be optimized further in the future.

Jan 1, 1994

By H. K. Fouad, L. A. Guirguis

The starting mill strip solution· for this study· is an ammonium uranyl tricarbonate solution of pH 8.2 containing 20g uranium/liter, after a DEPA/TOPO extraction process from sulfuric acid leaching liquor. To the first portion of the concentrated acidified strip solution, hydrofuoric acid is added at 95°C in reduced condition to obtain uranium tetrafluoride. The second portion of the uranyl carbonate strip is subjected to a precipitation step by admixing 0.3 volume of non-solvent precipitating agent such as acetone per volume of uranium. ·Uranium oxide (U30 8) is obtained from this precipitate by calcination for half an hour at 800°C in air. The third portion of the strip solution is neutralized to a pH 6.5 with sulfuric acid to precipitate iron and other contaminants. The solution is further acidified to a pH 1.85 with continuous air bubbling to remove CO2, followed by H2Ch precipitation at pH 3.5 to obtain uranyl peroxide. The latter is reduced by stannous chloride to obtain uranium trioxide dihydrate UO3. 2H20. Identifications, characterization· and purity of these products are carried out by complete chemical analyses, Scanning electron microscope study, tap density determination, X-ray diffraction and infrared spectroscopic investigations. The achieved results agreed well with that of the published data for these nuclear grade purity products.

Jan 1, 2000

By Zhihong Liu

Monodisperse micron size nickel oxalate particles with rhombohedron morphology were prepared from condensed Ni(OH)2 suspension by a novel gel-sol process proposed by one of the authors. Firstly, condensed nickel hydroxide gel was formed by fast adding 1 mol dm-3 NaOH solution into 0.2 mol dm-3 nickel chloride solution, and then oxalic acid solution with a concentration of 0.25 mol dm-3 was dropped into the gel drop wise through a pump equiped with a pH controller under preset pH value, and in this process, Ni(OH)2 gel was converted gradually into monodisperse nickel oxalate sol. The formation of the nickel oxalate particles was found to proceed through a dissolution-recrystallization mechanism from the nickel hydroxide gel. The product particles exhibited rhombohedron like shape with micron size long axis and sub-micron size short axis. The effects of such factors, as temperature, surfactants, et al, were evaluated experimentally on the particles sizes and morphologies.

Jan 1, 2006