Search Documents

By I. L. Follington

A breaker line support (BLS) monitoring system, BLSmon, has been designed and constructed by the CSIRO and installed and commissioned at Laleham No.1 Colliery, Queensland. This system was designed to record hydraulic leg pressure and canopy position measurements and relay these, in real time, to the surface. The system has shown itself to be capable of operating on the BLSs without any adverse affect on production, Analysis of the results of the monitoring exercise has shown that rate of change of leg pressures on the BLSs could be used as an aid in the prediction of adverse mining conditions. Under favourable mining conditions the supports were observed to initially unload from the set pressure, this unloading reduced with time and by the end of a typical lift cycle had either ceased or reversed slightly. This behaviour was considered to be due to one of four possible causes, these being; the compaction of floor debris, and/or compaction of the floor, and/or crushing of the roof and /or support creep. The actual cause can only be determined through detailed monitoring of both roof and support convergence. However observational data would suggest that compaction of debris and softened floor material beneath the supports was the most likely cause. The few positive loading rates recorded under these conditions were of short duration and occurred towards the end of individual lifts. Where mining conditions were unfavourable the negative rates of change of pressure, unloading of the support, were reduced throughout a lift, in both duration and magnitude, when compared with favourable mining conditions. Over the same period the positive rates of change were observed to be greater. The rate of change of loading and convergence can be utilised to identify the onset of instability in the lift area. However, before this facility can be utilised by the mine for the reliable prediction of instability more monitored data and sophisticated processing techniques are required. A mechanism has been postulated for the deformation behaviour of the roof and pillars in a mechanised pillar extraction operation from the continuously monitored data, observational data and results of previous studies. The 7 m wide fenders were observed to yield under abutment stresses before lifting commenced. The stability of these fenders throughout the lifting sequence was considered to be dependant upon the magnitude of their post peak load carrying capability. This is influenced by the post peak stiffness and the extent of roof lowering in the vicinity of the fender. Difficulties with fender extraction occurred where remnant coal left standing in the goaf caused uncaved goat to bridge to the mined fender. Difficulties were also experienced where sub-vertical jointing occurred in the roof of the split reducing it's ability to bridge effectively. Despite the relatively short monitoring period, the potential role and application of continuous monitoring in advancing understanding of the rock mass response to mechanised pillar extraction operations has been demonstrated. This understanding now requires enhancement and shows great potential for aiding the optimisation of mechanised pillar extraction operations.

Jan 1, 1992

By Thomas M. Barczak

The decade of the 90's brought an unprecedented increase in the development of innovative technologies to provide more effective and easier to install roof support in underground mines. To facilitate the application of these technologies to improve mine safety. National Institute for Occupational Safety and Health (NIOSH) developed the Support Technology Optimization Program (STOP). STOP is a windows based software program that provides mine operators with a simple and practical tool to make engineering decisions regarding the selection and placement strategy of these various standing roof support technologies. This program includes a complete data base of the support characteristics and loading profiles obtained through safety performance testing of these supports at the NIOSH Safety Structures Testing Laboratory. Support design criteria in the form of the required support load density at a specified convergence can he established from four options: ( 1 ) a data base of measured ground reaction data from various mines or ground behavior information inputted by the user. (2) determination of loading requirements based on a detached roof block or rock failure height. or (3) criteria based on the current roof support system, and (4) arbitrary criteria set the by user. Using these design criteria, the program will determine the installation requirements for a particular support technology that will provide the necessary support load density and convergence control. Optimization routines are also available to determine the most efficient support design for a user specified support installation- In addition to these performance measures. STOP can be used to compare material handling requirements and installation costs. Comparisons among the various support technologies are easily made including graphical analysis of relevant support parameters. This paper describes the STOP and its application to optimize standing secondary roof support systems.

Jan 1, 2000

By Alan Bugden

Goedehoop Colliery produces 8 million tonnes of coal a year, principally from room and pillar mining, and is situated in the Witbank Coalfield in the Republic of South Africa. The mine has a long and successful record of producing export quality coal from the 2,4 and 5 seams at depths ranging from 20 to 100 metres using modem mining equipment. Following a number of fatalities caused by large and unexplained roof falls in roadways and intersections of supported ground, a review of the roof control system at Goedehoop was carried out. This led in turn to a programme of underground measurements and surveys. This included detailed investigation of the roof falls, horizontal stress mapping, stress measurement and short encapsulation pull testing on roofbolts. These investigations led to a number of important conclusions in relation to the state of stress in the ground, the roof failure mechanisms, standard of rootbolt installation and performance of the roofbolt system. As a result of the work Goedehoop Colliery has made a number of substantive changes to the roof control management system at the mine. These include: 1. A recognition of the importance of horizontal stress as the main factor responsible for roof falls. 2 The forward planning of roof support based on known features which cause the stresses to be elevated. 3. The introduction of a more effective roofbolt system, which can be more easily installed to a high standard. 4. A response system based on risk assessment and monitoring roof movement on a routine basis. The paper describes the knowledge acquired, the conclusions drawn, the changes made and progress to date.

Jan 1, 2001

By Deno Pappas

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has been evaluating developments in sealant support systems from a ground control perspective. The proper selection and use of a sealant material can significantly enhance ground control which may result in a decrease in worker related injuries due to ground falls. The purpose of this paper is threefold: to briefly review the current state¬of-the-art technology in shotcrete and membrane developments, to evaluate the preliminary findings of a long-terra underground study of various types of sealant materials, and to examine installation practices that are critical for an effective sealant material. The underground study utilizes NIOSH's Lake Lynn Laboratory Experimental Mine to evaluate the long-term performance of several types of shotcrete and membrane materials. Sealant performance to date have been evaluated on a regular basis over a two year period. Although the study is still ongoing, critical mining practices were identified that may seriously effect the bond of the sealant materials to the mine roof and rib; most notably, the importance of scaling and thorough cleaning of the rib prior to application. Also, results from an extensive series of Schmidt Hammer tests found that the shoterete increased in strength by 70% during the humid summer months.

Jan 1, 2002

By C. Babcock

This Bureau of Mines report considers some equations for mine pillar design from 1833 to the present. Most of the equations are of essentially the same kind, using pillar width to height relationships. The effects of end constraint and test volume size, that were implied in some of these early equations have received special emphasis in recent years. Experimental testing in the laboratory throughout the period given has been on prisms or cubes of coal or rock. Most of the present concepts have been known since about 1912. Wilson has recently emphasized the effect of end constraint in his confined core concept, but a number of other earlier relationships have indicated an awareness of the effects of constraint as well.

Jan 1, 1981

By Keith Heasley

As part of the initial investigation and validation of a new boundary-clement formulation for stress modeling in coal mines. the underground stresses and displacements at two multiple-seam coal mines with unique stress problems are modeled and predicted. The new program, LAMODEL, calculates stresses and displacements at the seam level and at requested locations in the overburden or at the surface. Both linear elastic and non-linear seam materials can he used: and surface effects, multiple seams, and multiple mining steps can be simulated. In order to most efficiently use LAMODEL for accurate stress prediction, the program is first calibrated to the site-specific geo-mechanics based on previously observed stress conditions at the mine. For this calibration process. a previously mined area is "stress mapped" by quantifying the observed pillar and strata behavior using a numerical rating system. Then, the site-specific mechanical properties in the model are adjusted to provide the best correlation between the predicted stresses and the observed underground stress rating. Once calibrated, the model is then used to predict future stress problems abead of mining. At the two case study mines, the calibrated models showed good correlation with the observed stresses, and also accurately predicted upcoming high stress areas for preventive action by the mines.

Jan 1, 1998

By Timothy Ross

The Pittsburg & Midway Coal Mining Co.'s Kemmerer Mine is one of the deepest surface coal operations in the world, with the highwall extending to approximately 1,000 ft above the pit floor. To increase recovery, auger mining is being evaluated beneath the highwalls of several seams representing the current economic limit of pit development. The primary augered seam is over 50 ft thick, can approach 100 ft thick, and dips into the highwall at an average of 17 degrees. The seam thickness and dip present many geotechnical design and operational challenges for multiple Sup to five) lift augering. This paper presents the design criteria and methodology applied to determine appropriate web and septum thicknesses for the various cover depths anticipated, as well as operational measures that can be taken to increase overall coal recovery. The primary tool used in the design was the finite difference code FLAG. Models incorporating typical strata sequences associated with the coal seam were run at several different cover depths corresponding to the maximum anticipated auger penetration. Web and septum thicknesses were varied until the minimum thickness satisfying a given safety factor criterion was determined. Using this procedure, design curves were developed for web and septum thickness versus cover depth. Operationally, several recommendations were developed to ensure that overall coal recovery is maximized. By angering across the scam dip, auger penetration per hole can he increased dramatically, and by carefully planning maximum planned auger penetration versus hole spacing, increased coal recovery can be safely attained.

Jan 1, 1999

By Rocky Wu

Rock bursts are one of the greatest challenges to ground control in the mining industry. With increasing mining depth and mining scale, there are more and more industry requirements on yielding rock support. Since 2008, Jennmar has been conducting large scale research and development works to develop a technically reliable and cost-effective yielding rock bolt. This paper introduces a new yielding rock support: the Yield-Lok bolt. The bolt is characterized by the designed yielding ability to produce 150?250 mm (6?10 in) of deflection at 8?10 metric tons (MT) (7.9?9.8 t) loads for every 16.4kJ (12,096 ft lb) energy input. The bolt?s performance characteristics are consistent through multiple and varying amplitude of impacts. In this paper, the design criteria of the bolt and the principle of performance are described; the dynamic testing results are discussed; and the features and application of the bolt are presented.

Jan 1, 2011

By L. Z. Wojno

Tunnels in South African gold mines are developed at depths down to 3 600 m below surface where the virgin rock stress approaches 100 MPa and, on occasions, through rock where the field stresses exceed 150 MPa. In addition, many tunnels are subjected to increases in field stress of over 50 MPa during their useful lifetime. As a consequence, the walls of most tunnels are fractured causing the rock to dilate into the tunnel. Quantitative data on the extent of this fractured zone are presented. The function of support in these circumstances is to reinforce and maintain the integrity of the fractured rock. In 80 per cent of the 800 km of tunnels developed annually, the support methods used are capable of maintaining the stability of the tunnels. However, the remaining 20 per cent of tunnels is subjected to severer conditions where dilation in excess of 250 mm occurs and/or where the probability of strong seismic ground motion is high. In these tunnels, additional support is required. The type and pattern of support for both normal and severe conditions is described. In spite of the improved support used, damage to tunnels may occur. To minimize this damage, the concept of a rock reinforcing tendon that will yield and do work, when subjected to quasi-static or rapid deformation, has been put forward. Specifications for such a tendon are presented and the development of certain yielding tendons are described.

Jan 1, 1987

By Douglas Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because it can result in failures of ground that lead to both injuries and death. Spokane Research Laboratory personnel investigated electromagnetic (EM) emissions in a deep underground mine in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results suggest that (1) there is no increase in the number of EM emissions prior to recorded seismic activity, (2) some EM signals are generated during blasting, (3) interference from mine electrical sources mask seismic-generated EM signals, (4) EM emissions do not give enough warning (compared to seismic monitoring) to permit miners to leave a stope, (5) the distance an EM signal can travel in the rock is between 17.7 and 39.6 m (58 and 130 ft), and (6) current data acquisition systems do not differentiate between EM signals generated from seismic activity and random mine electrical noise. These results preclude monitoring EM emissions as precursors of impending catastrophic ground failure.

Jan 1, 2004

By J. R. Koehler

The failure of yield pillar-based gate mad designs to provide adequate ground control performance is primarily related to the use of "critically" sized chain pillars. A "critical" pillar is one that falls into a range of pillar sizes that are too large to either yield nonviolently or yield before the roof and floor sustain permanent damage, but are too small to support full longwall abutment loads. To directly compare the in-mine performance of critical and yielding pillar designs, the U.S. Bureau of Mines recently completed a field study in a tapering gate road at the Sunnyside No. 1 Mine, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m-wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m-wide design more closely approaches proper yield pillar dimensions. Probehole drilling of several 10.6-m-wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset. suggesting a properly functioning yield pillar design.

Jan 1, 1995

By Frank E. Chase

Geologic structures have been responsible for numerous underground accidents and fatalities, and are a constant-source of down time. During - longwall mining, ground control problems associated with geologic anomalies are aggravated by the abutment pressures which develop as the panel is retreated. Therefore, it is imperative that these structures be recognized and properly supported in head- and tailgates. Fractures, faults, clay veins, igneous dikes, and ancient stream channels (paleochannels) disrupt the lateral continuity of the mine roof and can cause falls in gateroads. Horsebacks and kettle bottoms are also hazardous because abutment pressures tend to "pop out' these structures into the gateroads. This Bureau of Mines investigation describes the physical characteristics associated with hazardous geologic structures, identifies the coal fields where-they have been observed, and, where possible, suggests support strategies and other mine plan modifications to help minimize their effect.

Jan 1, 1990

By John G. Oldsen

Passive cable bolting and active cable trusses have been used in roof support for more than two years Excellent roof control has been experienced by many coal operations. This paper covers the new and innovative developments in cable support systems and their application in mines. Multiple cable bolts, tensioned cable bolts, coal rib wrapping, and other cable applications will be covered.

Jan 1, 1997

By Kot Unrug

For the purposes of underground mine design, twelve cores of the Springfield (V) Coal (Pennsylvanian) roof and floor were retrieved. Each core was photographed, described fresh in the barrel, and the rock quality designation (RQD) was measured. Cores were wrapped in plastic and delivered to the rock mechanics lab. At the lab RQD was remeasured and new photographs were taken before running geotechnical tests including weatherability. Significant differences in barrel RQD's vs. lab RQD's have been noticed in spite of careful handling. The drill site RQD is generally used to calculate geotechnical results, but in some types of coal measure rocks, further fragmentation of core takes place with slight changes of moisture content, which occur even in well wrapped core. This creates a dilemma which RQD should be used for support design. Rocks around excavations are exposed to the significant changes in moisture content due to the seasonal weather changes and related fluctuation of humidity of air ventilating a mine. Therefore, it appears to be more realistic using laboratory RQD which corresponds closer to the actual rock condition around the excavation. Weatherability test, developed for characterization of time dependent behavior of rock exposed to fluctuations in moisture content, is thought to be related to the above-mentioned changes of RQD. In weak shales, mudstones and claystones which weather rapidly, it is essential to characterize their future behavior in the pre-mining stage. This can allow for a realistic design of primary, and particularly secondary support in coal mines, especially in coal fields where such geologic conditions exist.

Jan 1, 2003

By Lorraine Kent

Mine tunnel support using rockbolts was introduced in UK coal mines over the period 1987- 1992 and is now used in over 70% of all mine tunnels. In every case the reinforcement design has been based on the observational approach. After the initial reinforcement design has been established appropriate action levels are defined for predetermined amounts of movement indicating the onset of instability. If the action levels are exceeded appropriate remedial action is taken usually in the form of additional support or reinforcement to maintain stability. This paper outlines the observational design method as used in UK coal mine tunnels. It discusses the low cost instrumentation which has been developed to monitor roof deformation, dual height telltales, how action levels are defined based on the geotechnical environment and the types of remedial measures typically taken. An alternative approach for dealing with areas of increased deformation involves reacting to early roof movement trends and modifying the support installed at the face of the development accordingly. Installation of additional support at the face of the heading improves ground control in poor geotechnical conditions and has the advantage of potentially reducing later additional support costs. A case study is described to illustrate how 'early' action levels can be incorporated into a roof support plan enabling a flexible roof support strategy. Such a system will be site specific and continued analysis of monitored information will be required to confirm the action levels or to adjust them according to any change in geotechnical environment. More accurate roof deformation monitoring systems, such as the Remote Reading Telltale system recently developed by Rock Mechanics Technology Ltd. (RMT) and currently undergoing Mines Safety and Health Administration (MSHA) approval, are ideally suited to this application. The Remote Reading Telltale system provides accurate mine wide monitoring of roof condition on a surface PC.

Jan 1, 1999

By M Nombe

Based on the analysis of a case study at POWELTON No.2 MINE, it was determined that mine stability problems had occurred due to floor softening. A fireclay (underclay) layer in the immediate floor was softening after coal extraction and failing under pillars load. The thickness of soft floor was considered as the governing factor in the determination of the magnitude of floor displacement. The effect of floor thickness on floor displacement was evaluated by creating seven models that were input into the LAMODEL program. The properties of the soft floor were determined from a bearing capacity test performed in the Mains close to the area where mine stability problems had occurred. Moisture increase was considered in the reduction of floor bearing strength. Various strain-softening properties were allocated to the materials representing the soft floor. The LOW GAP POWELTON No.2 MINE was modeled and LAMODEL program was used to determine stress and convergence on both the coal seam and the fireclay seam. The results of critical stress and convergence obtained from modeling were compared with the actual floor failure area in the mine.

Jan 1, 2002

By Kanaan Hanna

Abandoned mines pose a serious threat to public health and safety, as well as the environment. When active workings approach old mine workings, miners could encounter significant hazards. Additionally, the presence of mined-out areas or voids underlying residential/commercial properties, transportation, and infrastructure systems can cause subsidence issues ranging from differential settlements and sinkholes to catastrophic collapse. All these features can result in adverse impacts in terms of cost and public safety. Traditionally, mine void detection and related engineering investigations for mine subsidence risk assessment and mitigation have been greatly dependent on systematic drilling and grouting backfill programs. The unknown location and condition of abandoned underground mines represent significant challenges to geologists and engineers in accurately evaluating subsidence hazards and developing appropriate mitigation measures. A comprehensive, multi-phase mine subsidence investigation was conducted at an abandoned western U.S. mine site. The mine operated in an approximately 8-ft (2.4-m) -thick coal seam using room-and-pillar extraction from 1919 to 1922. The mine lies at depths ranging from 50 to 100 ft (15 to 30 m), and it is overlain by critical pipeline and utility corridors. Any future subsidence/ sinkhole that occurs beneath or adjacent to the corridors could pose a significant threat, specifically to the structural integrity of the pipeline corridor. Therefore, the engineering geophysical investigation was initiated to determine the potential subsidence risk. This paper describes a recent success achieved by using integrated engineering geophysics in subsidence risk evaluation. A summary of significant results with emphasis on subsurface characterization, mine workings and voids delineation, modeling analysis, and high risk zones identification and mitigation strategy is presented.

Jan 1, 2011

By C. D. Peters

The Bureau of Mines has been researching remote sensing analysis of an underground coal mining area in Utah and computer-aided methods of defining ground control hazards in this mining area. As a result of these studies, a preliminary potential hazards map was developed for the test site. This map is based primarily upon a lineament (linear feature) analysis of Landsat satellite data. Other data used were paleochannel location data, resistivity data, and information from surface and underground field checking of the lineaments and ground control problems in the mine. Lineaments proved to be reliable indicators of hazardous areas, although the type and degree of hazard varies with different lineament trends and the presence of other conditions such as lineament intersections and intersections with other geologic structures or with paleochannels. Lineaments were observed to match faults, joints, and/or joint trends in the area. The paleochannel data, derived from drill hole data, provided basic information about potentially hazardous areas in the mine by suggesting where paleochannels could cause instability in the roof rock. The ground control problem data served largely to define the relative degree of hazard associated with lineaments and the types of hazards encountered in the mine. Resistivity data helped confirm the presence of fractures where they were expected to occur both from surface geology and from the lineament data.

Jan 1, 1986

By Denise Y. Dixon

The objectives of this study were to (1) document the hydrologic impacts of longwall mining on ground water, (2) identify the factors which affect the extent of dewatering, and (3) develop empirical trends to predict the extent of dewatering and recovery in advance of mining. The study was confined to three mine sites in north-central West Virginia. At each site, available ground water supplies were identified and monitored for dewatering effects and recovery. Mine A, located in Upshur County, West Virginia, has relatively thin overburden (approximately 715-280 feet). At this site domestic water supplies and specially constructed monitoring wells were monitored, continuing with an earlier study done by Cifelli arid Rauch. Most such supplies were completely dewatered over the longwall panel. Some of these wells have shown significant recovery, especially near a stream. Extensive monitoring of two nested piezometer wells revealed that dewatering generally started in advance of undermining in the lowermost monitored overburden zones first and then progressed upwards. Most dewatered wells completed in bedrock have shown no recovery, except. for valley drilled wells located within 100 feet of a Stream. Affected dug wells completed in valley alluvium rend located within 200 feet. of the nearest stream have shown significant recovery. Some wells have partially collapsed following mine subsidence. Mine B, having relatively thick overburden (approximately 585 to 900 feet), is located in Monongalia County, West Virginia. Ground water supply surveys have been conducted there in an attempt to study past dewatering effects. Owners reported Chat several wells were dewatered by longwall mining arid vertical air shafts that preceded longwall mining. Dewatered wells over longwall panels hove shown some recovery within 3 ½ years of mining. Mine C also has relatively thick overburden (approximately 585-900 feet), and is located mostly in Greene County, Pennsylvania. In addition to a survey of domestic water supplies at this site, five specially constructed monitoring wells were tested. The shallow monitoring wells suffered drops in water level due to mining but totally recovered within one day to three weeks after dewatering occurred. However, they did occasionally exhibit partial collapse during mine subsidence. Subsidence fracturing was beneficial in increasing the lateral hydraulic conductivity by a factor of about S to 22 for rock strata located within 124 feet of the surface, indicating enhanced shallow aquifer potential. One deep well suffered both partial dewatering and structural damage, with the state of water recovery bring uncertain. Also, two shallow domestic supplies out of five located over the mine were reportedly dewatered, but this claim could not, be substantiated.

Jan 1, 1988

By Dion Pastars

Kestrel Coal has undertaken a surface-to-seam consolidation program of faulted ground prior to longwall retreat in the 304 panel. Micro fine cement is used to improve the rock mass quality and therefore reduce the risk to personnel and equipment whilst increasing previously assumed sterilised reserves. The program is based on information attained from previously successful grouting campaigns in the Queensland coal area and follows the decision making process to ensure there is sufficient spatial permeation of cement across the faulted area. This data is used to assess the residual risk to the business in terms of health, safety and production

Jan 1, 2007