Search Documents

By Geoffrey Fosbrook, Donald Phillips, Anil Parikh

The Second Avenue Subway is a $16.8 billion project planned by the Metropolitan Transportation Authority (MTA) in New York City. It will reduce overcrowding and delays on the Lexington Avenue Line, improving travel for both city and suburban commuters, and improving access to mass transit for residents of the East Side of Manhattan. The project is a new, two-track, 13.5 km (8.5 mile) subway extending from Lexington Avenue at 125th Street in Harlem on the north end of Manhattan, to Water Street at Hanover Square in Lower Manhattan. The first phase of construction includes rock tunnels from 92nd Street to 62nd Street and connection to the existing 63rd Street station, three new stations, and track and systems from 105th Street to 63rd Street, allowing service between 96th Street and Brooklyn via an existing Broadway Line. The following describes the Project in detail, discusses the construction challenges addressed in the design, and the initial design/build contract to be awarded in 2005. A discussion of the planned mined construction of two rock caverns and a cut-and-cover station construction are also included.

Jan 1, 2005

By Antonio Raschillà

On the 2nd of June 2007 SELI S.p.A. started the excavation of Beles Tailrace Tunnel (Ethiopia). The new 8,07 m diameter DS Universal TBM utilized for the tunnel excavation was manufactured by SELI S.p.A. and allowed the installation of 30 cm thick concrete lining, contemporaneously with the excavation of 7,200 m of tunnel. The greatest part of the tunnel alignment was excavated in hard and sound basal-tic rocks. The paper describes the main steps of the tunnelling operations which led to a remarkably rapid excavation, with a peak production of 36 m / day and a final break-through achieved 46 days ahead of the contractual deadline. Furthermore the paper describes the work and logistic organization that was set up to efficiently perform the mechanized excavation in the very remote area of the project.

By Aditya Rana, A. K. Mishra, M. M. Singh, N. K. Bhagat

Many cases of derailments, train accidents and traffic interruptions due to the slope failure and rockfall have been reported in the past on Konkan Railway trackline because of unstable rock slopes. The authorities installed stability enhancement measures such as wire netting, rock bolting and shotcreting which were found insufficient. The failed geotechnical measures prompted authorities to excavate the unstable slopes. Rock blasting is generally not preferred for the excavation of slopes along the transportation route. Stabilisation and widening of slopes by blasting need closure of the route for a considerable time. Discontinuing traffic on Konkan Railway route was undesirable as it connects two important port cities Mumbai and Mangalore. The paper presents an innovative directional controlled blasting (DCB) technique for excavating three unstable slopes (i.e. cuttings) in hilly terrain without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw have been developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3 irrespective of the actual free face was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle has been changed from 80 to 82° to 45–47° and probability of wedge, planar and toppling failures was eliminated. About 100 such accident-prone slopes (52 km cumulative length, 7% of total route) situated at discrete locations along Konkan Railway route were stabilised using the technique. No incident of rockfall and slope failures along these slopes has been observed after the stabilisation.

By C. K. Kocsis, S. Hardcastle

Mine ventilation, requires electricity to operate the fans and fossil fuel for heating. Typically, this accounts for approximately 40% of the overall underground energy consumption. This is considerable, and one of the major causes of this expense is that most mine ventilation systems are designed for the "worst-case-scenario" with respect to ventilation demand, which is commonly dictated by diesel equipment usage. Once designed, mines tend to operate their ventilation system at this peak level despite their exceeding day-to-day development and production needs due to lack of appropriate ventilation controls. In underground metal mines, TeleminingTM, which includes the tele-remote operation of mobile development and production equipment from surface, will change the mine design criteria including its support infrastructure such as the ventilation system. With the removal of machine operators to surface control rooms, conventional ventilation systems designed to dilute and remove pollutants can become redundant. Depending on the ultimate need for ventilation, its cost in automated mines with tele-remote equipment operated from surface will be lower than the cost of ventilation in conventional mines. These cost savings, which could be significant, would not only come from the ability to reduce the amount of ventilation in the mine, but also through the capacity to automate its distribution. This paper provides an indication of the new airflow requirements in stopes and dead-end developments for the tele-remote and automated mining processes based on climatic modelling. Furthermore, this paper makes a cost benefit analysis by comparing the ventilation system operating cost of a conventional underground metal mine based on the mobile diesel powered equipment design criteria with the newly redesigned ventilation system operating cost of an automated mine based on the "heat management" design criteria.

Jan 1, 2002

By Steven W. Hunt

Appropriate seals, portal ground improvement, and compatible shaft construction techniques are vital elements for launching and receiving tunnels effectively in urban areas where adjacent property requires protection from excess ground movements. This paper focuses on seals and ground improvement along with shaft wall types, required to launch or receive tunnel boring machines within wet, permeable ground at the portal zone. The paper also discusses probing to verify suitability before the tunnel eye is cut. Methods addressed include: rubber gasket seals; soft eyes; double walls; top hats for reception; and, portal zone ground improvement (permeation grouting, jet grouting, un-reinforced slurry diaphragm wall panels, ground freezing, deep soil mixing, dewatering, and over-excavation and backfilling). This paper focuses on challenges with launch and reception of pressurized-face TBMs with precast concrete segment linings. Challenges related to pipe jacking are discussed in a separate paper titled ?Mitigating Microtunnel Launch and Reception Challenges? (Hunt and Finney 2008).

Jan 1, 2008

By Martin Herrenknecht

Tunnel boring machine (TBM) development continues to take on not only larger diameters, but also more difficult ground conditions. Ground conditions consisting of unstable faces with water pressures up to 15 bar have required innovative design approaches. A systems approach has been required to produce tunneling machines that can safely excavate the tunnel in an efficient, cost-effective manner that stresses production and labor saving approaches. This article reviews the current design developments and present recent projects where these most recent principles have been applied. The world?s growing population and rapidly proceeding urbanization are boosting an enormous demand for new and high-capacity infrastructures to secure the mobility of goods and people. Densely populated areas face the challenge of providing efficient traffic infrastructure such as a modern public transport system. At the same time, the maintenance and modernization of supply and disposal structures for water, sewage, energy and communication are essential. Last but not least, are supra-regional transportation routes such as long distance water diversion schemes. All of these projects are as demanding and are characterized by a tight time schedule. In this context, the demand for efficient tunnels for traffic and utility lines is increasing, as new infrastructures often leads underground because of limited space above ground. Also, tunnels are the obvious choice to cross natural barriers like mountain ranges. To handle the complex and variable geological conditions and other constraints, such as low overburden, high water pressure or long tunnel drives while facing increasing demand of a quick completion of a project, mechanized tunneling sets standards regarding safety, profitability and environmental protection in traffic tunneling projects as well as in the trenchless construction of utility tunnels. Different machine types and working principles have been developed to master various geological and hydrogeological requirements. Continuous activity in research and development leads to constant improvement of the mechanized tunneling process.

Jan 1, 2008

By James D. Nickerson

Thee Brightwater water treatment facilities, currently scheduled to be completed in 2010 and begin operating in 2011, will serve the northern part of King County, WA. The facility includes a new treatment plant and extensive conveyance system consisting of more than 21 km (13 miles) of influent and effluent conveyance tunnels and five portals. The majority of the conveyance system tunnels are mined by tunnel boring machines (TBM) and microtunnel boring machines (MTBM). Tunnel and portal construction is divided into three main contracts. The Ballinger Way receiving portal, constructed under the central tunnel contract, is the terminus for the BT-3 leg of the central contract and the BT-4 terminus of the west contract. The shaft has a 7.3-m (24-ft) finished inside diameter (ID) to accommodate removal of the central project TBM and the west contract TBM and extends to a depth of 66 m (216 ft) below grade through a complex and challenging soil profile characterized by multiple ground water tables. Vinci Grand Projects/Parsons/Frontier-Kemper Constructors (VCFK) was the joint venture team for the Ballinger Way portal. Frontier-Kemper was responsible for the shaft sinking. VCFK evaluated either slurry wall techniques or ground freezing for earth support during excavation of the portal and liner installation. The selection process took into account the vertical depth, cost, past practice, geology, water tables and a 9-m- (30-ft-) thick zone of contaminated soil at the top of the shaft. Ground freezing, which would also act as a hydraulic barrier, was deemed the better option for this project. The contract was awarded to New Jersey-based geotechnical contractor Moretrench. Typically, frozen walls, by design, key into an underlying cutoff. At the Ballinger Way portal, however, the [ ] freeze bottomed out in a substantially thick stratum consisting of predominantly clay, but with some inclusions of permeable soil that indicated significant ground water pressures. To ensure stable conditions at the bottom of the shaft, Moretrench, which also specializes in dewatering, designed and installed a perimeter array of deep wells to temporarily depressurize the permeable soils. The movement of ground water generated by pressure

Jan 1, 2009

By J. Drelich, M. Pawlik

An improved experimental procedure to measure contact angle has been consolidated with coal surface preparation involving polishing with abrasive paper, alumina powder, and a cloth, followed by ultrasonic and mechanical cleaning. Specifically, the captive-bubble measuring technique has been compared with the sessile-drop technique and the former has been recommended for the examination of the hydrophobic properties of coal surfaces. Results of the research program, which is currently under way, on the examination of the effect of the nature, amount, size, and distribution of mineral inclusions in coal, on its wettability are briefly reviewed.

Jan 1, 1999

By E. R. Spencer

National Institute for Occupational Safety and Health (NIOSH) researchers conducted an investigation to quantify sound levels and to determine the amount of sound reduction provided by engineering noise controls installed in a talc processing plant. Baseline sound level and sound intensity measurements were performed at the plant and the measurement locations were recorded for comparison to post-control measurements. Follow-up measurements were then made at the same locations after the initial noise controls were installed. The plant subsequently decided to implement additional noise controls and the researchers returned to conduct measurements for a final analysis of all noise controls. The most significant results showed a sound level reduction in the main mill area from a range of 93-104 dB(A) down to 90-94 dB(A), and a total sound power level reduction of 21 dB(A) for air classifying mill 3.

Jan 1, 2008

By Richard R. Klimpel

Introduction Froth flotation is one of the most common unit engineering operations in use today. Its aim is to upgrade the quality of coal by removing ash/pyrite and separating selected minerals from undesired gangue materials. Flotation has been successfully practiced at the industrial scale for more than 50 years. Its use is increasing due to the ever decreasing feed grades of the coals and minerals being processed. Flotation has also shown itself to be a flexible process that lends itself well to many solid/solid separations. Thus, with surprisingly little equipment modification, separations can involve very different particle sizes and densities, and relative weight ratios of materials to be separated. In addition, the flotation process is economic, especially when compared to size reduction, its associated precursor process. Flotation also lends itself to continuous operations with a given equipment configuration. The operation must exhibit an ability to vary feed rate of solid to the process by as much as 50% without a total collapse of separating efficiency. In addition, the mechanical flotation cell is scaleable from 2.8 to 57 or 85 m3 (100 to 2000 or 3000 cu ft) with surprising ease relative to other unit engineering operations over the same relative size increase. The separating medium used is water. Most of the chemicals required - pH regulators, frothers, collectors, activators, and depressants - are all relatively inexpensive and common. They are not usually used in large quantities. Froth flotation is certainly one of the most versatile and forgiving unit operations in the chemical, mining, and agricultural industries. The problem with the industrial flotation process is that it is fairly easy to get reasonable results and relatively difficult to get excellent results. Why is it so difficult to fine tune the froth flotation process? There are some obvious reasons and a few not-so-obvious factors. The obvious category would certainly contain the tendency of natural feed materials (ores and raw coals) to have variable physical, metallurgical, and surface properties. This occurs even when special care is taken to minimize such differences with blending. There is another obvious reason for difficulty. An inherent broadness of the feed particle size range to flotation results from using any of the common industrial-scalefine grinding devices - ball-, rod-, or autogenous mills. Research has been done into the chemical reagent and equipment aspects of flotation. It has shown strong interactions (limitations) of chemical reagents and equipment on larger and smaller particles. The point is that current flotation practice works best on average- or medium-sized feed particles. The greater the amount of large or small particles, or of both large and small, the more difficult it is to achieve excellent flotation results. Other reasonably obvious factors include: • variations in mineral type and liberation sizes; • water chemistry variations such as those involving Ca", C03, or Fe", or various soluble metal cations; • the presence of stray organic materials such as returning soluble reagents or partially degraded reagents in reuse water; • the lack of reliable on-line instrumentation for monitoring and control; • frequent equipment malfunctions of all types; • excessive feed rates for installed plant capacity; • poor operator interaction with the process; and • poor reagent dosage control. There are less obvious, but real limitations to flotation. These are inherent in the design and operating characteristics of the most common cell design in use today - the mechanical flotation cell. Individual performance attributes of the chemical reagents used, along with their manner of use, also carry limitations. The bulk of this paper will deal with chemical reagents and their use. Chemical reagents In 1979, the author and his co-workers were asked to invent and implement, at the industrial scale, new flotation reagent chemistry. After reviewing some of the literature (Sutherland and Wark, 1955; Klassen and Mokrousov, 1959; M. Fuerstenau, 1962; D. Fuerstenau, 1976; and Leja, 1982), a series of carefully controlled plant scale tests were set up. These tests were designed to understand existing reagent scale-up from the laboratory to the plant. They were to quantify at the plant level the effect of some of the more important, controllable chemical reagent factors (frother and collector type, frother and collector dosage, pH effects). This is a learning experience that all researchers involved in flotation theory should experience. It quickly became apparent that: • because a factor is important

Jan 12, 1988

By R. K. Sinha, B. S. Choudhary, Desh Deepak, A. K. Mishra, Hemant Agrawal, Shankar Kumar

There are several methods (empirical, statistical, and machine learning tools) to calculate blast-induced ground vibration. Still, due to complications in the blasting procedure, under varying blasting loads and strata conditions, it is not easy to predict and simulate blast vibration precisely. Therefore, a study was conducted to simulate the field blast data in Ansys software using explicit dynamics. For this study, monitoring of ground vibration for 20 single hole blasts was carried out. The density of emulsion explosives was in the range of 0.9 to 1.15 g/cc. In the laboratory, rock properties were determined from the rock sample collected from the mine site before blasting. The in-hole velocity of detonation (VoD) and the density of the emulsion explosive were also determined. These parameters were used for numerical analysis to know the ground vibrations at specified points. The results of ground vibration predicted by the model are validated using field data.

By L. A. Baker

The presence of goethite in a hematite ore has been shown to strongly affect the time of heating to the firing temperature. The investigation of spalling of single pellets and of packed beds has enabled free water and goethite spalling to be identified as separate phenomena. In addition, it has been shown that even for an 18 inch deep bed of green balls the free water and goethite drying periods can be considered separately. Based on this observation, a method of predicting production rate and hood temperature profile is presented. The method required knowledge of the ore goethite content, ore grind and the green pellet bulk density. Laboratory results were found to be in good agreement with actual plant practice and have led to improved process performance.

Jan 1, 1972

By C. J. Pritchard

Controlled recirculation of ventilation air in underground metal and nonmetal mines has the potential to improve airflow and the health and safety of miners when implemented properly. Previous research by Robinson, Marks, Cecala and others concluded that the success of a district recirculation system is predicated upon an adequate supply of fresh air and the use of a reliable monitoring system for safe operation. This recent research also showed that contaminant levels will not exceed pre-recirculation levels, and that district recirculation can improve the dilution of face contaminants, especially methane gas. To illustrate the process of implementing controlled recirculation and also to promote and give guidance to mine operators in consideration of this tool to improve mine airflow, Office of Mine Safety and Health Research (OMSHR) researchers acquired baseline airflow and contaminant data from a multi-level room-and-pillar nonmetal mine and used commercial ventilation network software to simulate base case conditions and recirculation of mine air. Mine return air baseline contaminants of dust and diesel particulate matter were at lower levels than intake air, providing the potential for improved face air quality. A ventilation model implementing controlled recirculation was developed and analyzed, showing an increase in air quantity at the face, improved intake air quality, and contaminant exposure levels below those set by statutory requirements. These results, along with conclusions reached by previous researchers, provide the basis for examining the safe and effective implementation of controlled recirculation in metal and nonmetal underground mines using this mine as an example.

By Andrew J. Petruska, Austin F. Oltmanns

The paper proposes a capacitive load cell for detecting changes in material and tool wear conditions for conical picks used in underground mining. The current process is dangerous and subjective, relying on human operators near the cutting interface. The new sensor aims to improve worker safety by allowing operators to perform their functions from a greater distance.

Aug 1, 2023

By Georgios Bartzas, Vasiliki Karmali, Konstantinos Komnitsas, Anna Kritikaki, Dimitra Vathi, Stylianos Tampouris, Arne Peys

Large volumes of slags, with varying mineralogical and geochemical characteristics, are produced annually by the ferrous and nonferrous metallurgical industry. Most of them are considered as potential secondary resources and may be valorized, following the principles of circular economy, for the recovery of critical elements, including energy transition metals. Apart from the economic benefits, valorization of slags may contribute to the competitiveness of the metal industry and the conservation of natural resources. Valorization also results in minimization of environmental impacts on soils and waters in slag disposal areas, due to the prevention of solubilization and subsequent migration of potentially hazardous elements. The present study utilizes ferronickel (FeNi) slag for the production of alkali-activated materials. The effects of the main experimental parameters, including sodium hydroxide (NaOH) molarity, silica/sodium oxide (SiO2 /Na2O) molar ratio in the activating solution, precuring and curing time, curing temperature and aging period on several properties of the final products, are assessed.

Apr 1, 2025

By M. J. Sapko

From 2001 to 2007, the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) conducted studies to develop alternative methodologies to full-scale explosion testing for deter-mining the ultimate strength of mine seals. As a result, the PRL developed and proposes an alternative seal-strength evaluation method based on a hydrostatic pressure-loading concept. The researchers suggest pressure loading a seal using water to twice the expected dynamic design load. The hydrostatic chamber test offers a means of validating seal designs, establishing appropriate resistance functions and determining the ultimate strength of seals through testing to failure. This article contrasts the full-scale explosion and hydrostatic testing of mine seals using a simple dynamic system model and principles.

Jan 1, 2008

By A. L. Williamson, G. Savci

Hydrologic assessments of existing and proposed waste rock stockpiles (WRS) are typically required for application of operating and closure permits at mine sites. The results of these assessments can be used to determine the applicability of the state groundwater permit program requirements to the operation and closure of these stockpiles. The objective of this hydrologic assessment was to ascertain whether or not the WRS at the Ajo Mine have a reasonable probability of discharging potential pollutants to the underlying aquifer under the operational mine conditions. The hydrologic assessment was performed based on an evaluation of climatic data, prediction of the net infiltration rate through the WRS and prediction of additional hydrologic factors such as the time required to deplete available moisture storage in WRS. The predicted net infiltration rates ranging from 0.13 inches/year (1.1x10-8 cm/s) to 0.24 inches/year (1.9x10-8 cm/s) are below the threshold value of less than 10-7 cm/s recommended by Hutchison and Ellison (1992) as being characteristic of conditions that produce no or negligible quantities of seepage. In addition, the total time required to deplete available moisture storage within the Ajo Mine WRS and for any potential seepage from the WRS to reach the underlying aquifer is estimated to range from 260 years to 1,950 years. Collectively, the climatological and geotechnical investigations and the hydrologic predictions demonstrate that the WRS at the Ajo Mine hydrologically do not have a reasonable probability of discharging pollutants to the underlying aquifer. As a result of this prediction, the stockpile will not be regulated under the state groundwater permit program and operational and reclamation requirements will be limited to managing surface water runoff.

Jan 1, 2002

By James W. Estep

The sulphur shortage that has occurred in the past two years has directed attention more and more toward sour natural gas reserves, Wellhead values of sour gas vary widely depending upon the acid gas composition, location, market conditions, and necessary processing charges. Preparation of a saleable residue gas is considerably more involved and expensive than that normally encountered in treating a sweet gas. Recent revisions in sales gas specifications have increased capital costs and processing charges. The presence of hydrogen sulphide and carbon dioxide in a natural gas contributes to shrinkage factors that may approach 50%. Fuel required by the gas sweetening process and sulphur slant tail gas incineration also contributes to a further reduction in the volume of residue gas available for sale. The additional processing facilities involving gas sweetening, mercaptan removal, expanded utilities, sulphur recovery and sulphur handling, all demand additional operating and maintenance staff. A favorable sulphur market under certain conditions may justify the processing of sour gas whereby sulphur is either a by-product or a co-product, Five typical cases involving different compositions of sour gas are presented for evaluation. Capital costs, operating problems, and operating costs are presented in detail for full economic evaluation

Jan 1, 1967

By William R. Yernberg

In October 1999, Liebherr-America, Liebherr Construction and Liebherr Mining Equipment held anopen house at its Newport News, VA, plant. The open house was held to celebrate the company’s50th anniversary and to demonstrate the new TI 272mining truck. Attending the open house members of the media, vendors and company representatives from all over the world. In his introductory comments, company president Peter Eller announced Liebherr’s dedication to expanding its presence in North America. Liebherr now has 30 dealers across the United States. As part of the open house, a brief history of Liebherr was presented, beginning with its creation in1949. Liebherr engineering and sales representatives were available to answer questions.

Jan 1, 2000

By Dennis Ofiara

Several recent tunnel jobs have required special adaptations of hard rock TBMs. Some of the special job conditions are ?no blast? launch requirements, small shafts or launch pits, proximity to existing underground structures, and short tunnels where the TBM must be retrieved through the primary lining. This paper describes a few of these projects, and the machine adaptations that have made TBM excavation feasible.

Jan 1, 2008