Search Documents

By Y. J. F. Haven, G. H. J. Kitson, D. G. Beadle

I have read this paper with considerable interest. By using an automatic instrument to assess the dust samples taken in South African collieries, the authors are ahead of the gold mining industry, which still uses the laborious method of microscopic assessment, with its limited accuracy, of the half-a-million dust samples taken each year. As the authors state, the result obtained from the photoelectric assessment of the samples is approximately proportional to the surface area of the respirable dust. However, modern theory is that, in assessing coal dust, it is the respirable mass which is important in determining the danger to health. Thus Table II of their paper is of considerable value in showing the relationship between the P.E.R. value and the mass concentration measurement. Unfortunately this table only gives the mean relationship. The important point is to know the scatter around this mean. If the scatter is small, then this mean value (for different operations) would have considerable value in converting from respirable surface area to respirable mass, but if the scatter is large, then such a conversion, using a fixed factor, will have little value. In the text the authors mention the range of values as being between 3 to 24, but without a statement on the number of samples used to determine this range and their distribution, this is a rather nebulous statement. I hope, in their reply, that the authors will give, in statistical terms, some statement on the overall correlation between these two parameters. I might add that at present a member of my staff is working on similar relationships for dust samples taken in gold mines. Another factor which may well be most important in determining the danger of dust levels in coal mines is the composition of the dust, specifically its quartz content. I understand that the authors have some information on this point, and to make their results of greater value in International comparisons of dust levels and the concomitant development of pneumoconiosis, it will be extremely useful if they could place this information on record. Even though, as I have said above, modern theory postulates that respirable mass is a better parameter to use than respirable surface area, the problem remains of how to measure this parameter with short time sampling, which, as the authors point out, is their preferred strategy for dust sampling and dust control. I know of no easily portable instrument, independent of external power supplies, which can, in 5 to 10 minutes, collect sufficient dust to enable it to be weighed accurately. Thus the authors' implied intention of continuing to sample by their present techniques and using their present parameter to report the results is, in my opinion, an entirely valid decision.

Jan 10, 1968

By R. L. C. Maggs

The following members of the Orange Free State Branch and visitors paid a mini-visit to the H.J. Joel Gold Mine on 23rd January, 1991: Members E.N.D. Westgate Organiser R.LC. Maggs Hon. Secretary S.V. Stander S.P. van Wyk D.S. Minnie O.W. Fourie Visitors C. Knight-Hassel J. Campos E.W. Booysen J. Steyn P.!. Masseratte C.J. Higgins S. Guven F. Scof N. Hastings R. Hays On arrival at the Mine, the visitors were welcomed by the General Manager, Mr Chris Naude, who introduced the staff who would be involved in the visit.

Jan 1, 1991

A colloquium on 'Recent Developments in Wearresistant Materials', organized by the Technical Programme Committee: Physical Metallurgy of the SAIMM, was held at Mintek on 7th May, 1985. After delegates had been welcomed by Dr P.T. Wedepohl, Chairman of the Organizing Committee, Mr J.D. Austin, President of the SAIMM, delivered the opening address. Corrigenda to article on copper* I read with considerable interest the recent articles on copper by Mr C.O. Beale as published in the Journal. However, in Part 11 the section dealing with Prieska Copper Mines (Pty) Limited contained several factual errors, details of which are given below.

Jan 1, 1985

By D. Limpitlaw

Industrial mining in Zambia started in the 1930s when the world class copper deposits near the border with Katanga were developed. The discovery of these deposits began at the turn of the century when the first claims in the Copperbelt were pegged at Chambishi, north of what became the town of Kitwe1. World War I and the difficulties of raising sufficient capital for such large scale undertakings delayed the exploitation of these deposits. Following this hesitant start, a large copper mining complex was built, resulting in the development of five major towns, all highly dependent on the mining and beneficiation of copper and cobalt. Copper became so important to the country that, on independence, the only non-mining town to make it onto a list of the top six was the capital, Lusaka. From commissioning of the mines to the end of the colonial period in 1964, copper production increased to just over 640 000 t annually2 (see Figure 1). After the establishment of the new Zambian state, production continued to increase, supported by a benign legislative environment and strong international copper prices. The government of Kenneth Kaunda was intent on improving the conditions of the rural poor and reducing unemployment in urban areas. To this end, the government embarked on an ambitious project of refocusing Zambia's economy away from the colonial role of commodity supply to one of decentralized mass employment. The Copperbelt industrial complex was key to the success of this approach, and in 1969 the Zambian State acquired a 51 per cent stake in Zambia's two main copper producing companies: Roan Selection Trust and Rhodesian Anglo American Corporation. The former became Roan Consolidated Mines Ltd (RCM) and the latter became Nchanga Consolidated Copper Mines Ltd (NCCM). In the year they were nationalized, the mines produced at least 720 000 t of copper? and employed approximately 48,000 workers (see Figure 2)2-4. The subsequent economic policies of the Zambian Government depended heavily on the state's ability to monopolize the proceeds of copper mining.

Jan 1, 2011

By O. S. Tinkler, K. C. Sole

"Although the first large-scale application of copper recovery by solvent extraction took place in Zambia in the early 1970s, it is only in the last decade that this technology has become widely employed in this part of the world and is now a mainstay unit operation in copper hydrometallurgical flow sheets. The mineralogy of the ores of the African Copperbelt, and hence the characteristics of African leach liquors, differs significantly from those in Chile and the southwestern USA, where copper solvent extraction has had a long and successful history. These differences provide operators, metallurgists, reagent vendors, and engineers with many challenges: new approaches are needed to adapt solvent-extraction technology for successful implementation in this region. This paper examines typical operating practice in the African Copperbelt, discusses differences compared with other parts of the world, and looks at some of the challenges and opportunities presented by these flow sheets. IntroductionFollowing the success of the Rancher’s Bluebird and Bagdad solvent extraction and electrowinning (SX–EW) operations in Arizona in the late 1960s, the Tailings Leach Plant at Chingola, Zambia, became the first large-scale copper SX plant in the world, commissioned in 1974. Despite the equipment design now being outdated, this plant still continues to operate successfully, indicating the versatility and adaptability of this technology. Today, there are some 75 copper SX operations worldwide with cathode production above 10 kt/a. The top ten producers currently account for about 40% of the global 4.3 Mt/a SX–EW copper production. South America (predominantly Chile and Peru) is the largest copper cathodeproducing region, with annual production of some 2 Mt. The Central African Copperbelt (Zambia and the Democratic Republic of Congo (DRC)) is second, with cathode production of 1.2 Mt/a, and North America (USA and Mexico) third, producing close to 0.8 Mt/a Cu (Solvay Cytec data, 2014). The remaining 0.35 Mt/a comes from all other regions combined (referred to as ‘Rest-of-World’)."

Jan 1, 2016

By G. L. Gomes-Sebastiao, W. W. de Graaf

"Gomes Sand is a quarry operation that produces sand and aggregate for the construction industry. The quarry is experiencing inconsistencies in the fragmentation and poor pit conditions as a result of poor drilling and blasting practices. This results in excessive downtime in the load and haul and crushing processes.A benchmarking exercise of the blasting practices was conducted to evaluate the effect of the inconsistency on the mining cycle. After changes in the blasting practices the downtime was reduced, which improved the crushing plant utilization by 4.9%. The improved blasting practices and more consistent fragmentation decreased the average number of loads lost each month due to jaw crusher blockages from 9.2% to 3.9% of plant throughput. The change in blasting practices also improved pit conditions. IntroductionGomes Sand is a quarry operation that has been in operation since 2009, producing sand and stone for the construction industry. The quarry was experiencing unacceptable blasting results. The repercussions included uneven pit floors, large amounts of oversize rock (>500 mm), and inconsistent fragmentation.The blast results affected the load and haul operations as well as the efficiency of the crusher. This resulted in downtime in the daily operations, and consequent production and revenue losses.The crusher product should have a top size of 50 mm. A blast fragmentation of <50 mm would improve the downstream operations and the crusher throughput.An investigation into the blasting practices was carried out to assess whether the downstream delays can be eliminated by improving the blast results. The exercise included:* Assessing if the designed blast layout is adhered to on the bench* Observing the quality and control of drilling* Observing the charging procedure of the blast-holes* Benchmarking the fragmentation consistency of the blasted rock using current blast design and practices* Analysing the throughput of the crushing plant* Investigating the power consumption of the crushing plant and determine if a change in blasting practices will affect this* Evaluating the hours spent by the hydraulic hammer on secondary breaking."

Jan 1, 2017

By A. A. Bradley, P. J. D. Lloyd, A. J. Freemantle

Developments in centrifugal milling by A. A. BRADLEY,B.Sc. (Rhodes) (Visitor), A. J. FREEMANTLE, B.Sc. Hons. (Wits) (Visitor), and P. J. D. LLOYD, B.Sc. (Chem. Eng.), Ph.D. (Cape) (Fellow) The theoretical and experimental results of a study of centrifugalmills are reviewed. Means for the scaling up of such mills are suggested, and tests on a prototype mill are described. Despite the high lining wear in the centrifugal machine, which reduces its productive availability, its other advantages suggest that there is merit in pursuing its further development.

Jan 6, 1974

By D. Gerhart, J. Hung, J. Hackwood, A. Pix

A computer-based, real-time mine management system has been installed in a number of underground operations. The system’s innovative software application is coupled with wireless data acquisition and database management to provide complete mine monitoring and control execution in closed-loop control fashion. The system is well suited to automatically assign equipment, acquire status, and reassign resources based on status; and to automate information handling. The system has provided mines with improved utilization of the equipment fleet and mining crews, and reduced workplace cycle time. This paper describes the deployment of systems at a number of underground mining operations and discusses future development of the system. Keywords: Computer-based: Real time: Utilization: Mining cycle control: Monitoring: Productivity

Sep 1, 2001

To B. K. Martus I discussed several points raised by Mr Martus in my reply to Professor Krige*. Mr Martus discusses several possible interpretations of optimum South African sales, but in my paper these sales refer to the sales level that maximized the working profit of the whole South African gold-mining industry over the past eleven years. Mr Martus also seems to be under the impression that the paper deals with the future. While there may be references to the future, and some implications for the future may be obvious, the paper deals essentially with the past eleven years.

Jan 1, 1984

This paper considers the probability of the occurrence of potential rockfals in deep-level gold mines where there is point support (props, pipesticks, and timber sticks). The investigation described gave rise to the following implications: natural joints subparalel to the direction of strike have a controlling influence on the potential occurrence of rockfals; with discrete types of support such as props at typical sparings, there is a significant probability of the occurence of potential rockfals; the use of headboards oriented in the direction of strike reduces the probability; and loss of support from a prop increases the probability.

Jan 1, 1989

Discussion of the above paper by G. J. van JAARSVELDt Mr Ortlepp&apos;s paper is important, and deals with a subject towards which much controversy and insufficient basic scientific logic, in my opinion, have been directed. He attempts to remedy some of our unscientific popular misconceptions, and for this we thank him. However, I regret to say that experience has shown that some of his statements cannot be allowed to pass unchallenged. Author&apos;s reply Mr Van Jaarsveld&apos;s contribution is welcome because it provides an opportunity for me to clarify certain points that were perhaps not adequately explained in the paper.

Jan 1, 1979

By H. Wagner

The paper points out that bord-and-pillar mining is the most important method of coal extraction in South African underground coal mines, and advocates that pillar design procedures should be refined to make more rational allowance for the differences in strength properties between various coal seams and roof and floor strata. However, any deviations from well-established design procedures must be based on sound engineering principles and reliable data on the strength properties of the seams and strata concerned. Recent information indicates that practices for the protection of surface structures against underground mining should be revised.

Jan 1, 1980

By M. B. Cortie

An account is given of the development of ferritic stainless steels since their discovery in the early years of this century. The alloys became very widely used in the 1950s, the market during that decade being driven strongly by a demand for automobile trim made of ferritic stainless steel. The production of ferritic stainless steel declined as a proportion of the total at the end of the 1950s as consumer preferences changed. However, the market is now growing strongly again, this time driven by a demand for oxidation-resistant alloys for motor-vehicle exhaust systems. The tonnages produced, applications, and market shares of the various alloys are discussed and compared. Trends in world stainless-steel production, product forms, technological development, and usage are examined.

Jan 1, 1993

By D. D. Aksenova, V. A. Ignatkina, L. A. Samatova, A. V. Lygach, E. D. Shepeta

Calcium minerals such as scheelite, phosphate, apatite are valuable minerals, which have similar flotation properties to the calcium gangue minerals. An additional problem is the fine dispersion and close mineral association of valuable and other minerals. Low polar compounds (non-ionic surfactant), such as fatty iso alcohols, neonol and phosphol, and their combinations with sodium oleate have been studied using flotation of monominerals and ore flotation; ATR IR spectroscopy and TEM for study surface of minerals; UV spectroscopy for control solubility, aggregation and de-aggregation processes. Increase in solubility of fatty acid collectors was confirmed by low soluble (heteropolar) compounds. Oxyethylated esters of phosphoric acid are adsorbed on phosphorite by -O2PO2R2 and on other rock minerals by donation of OH bond. Same effect shows difference of adsorption of fatty iso alcohols on calcite and scheelite. The different forms of adsorption of ionic and nonionic compound on a sparingly-soluble mineral surface creates distinction of the flotation kinetics and technological balance of ore flotation. The results of the separation of flotation of scheelite from calcite depend on the order of pouring into pulp of fatty iso alcohols and oleate, and their ratio in the mixture. Increasing scheelite recovery into rougher scheelite concentrate by 3.6% for both the flotation and sludge classes was obtained. Calcite recovery varied slightly upwards or downwards by 0.8-2.4%. The use of the non-ionic surfactant phosphol in combination with a fatty acid soap allows for obtaining a phosphate concentrate with more than 28% P2O5 content and almost 80% recovery in flotation operation. It is not obtainable with other reagent regimes. Keywords: Flotation, calcium minerals, oleate, fatty isoalcols, neonol, oxyethylated esters, adsorption

Jan 1, 2020

By N. J. Alderman, R. Haldenwang

Flumes are ubiquitous throughout the mining and minerals processing industries as well as being used in the polymer processing and pulp and paper industries. With the increased demand for the transport of highly concentrated slurries in rectangular open channels, there is an impetus for a better understanding of the role of rheology in flow hydraulics. Until recently, design of such channels has been based on either the Chézy or Manning equations used for modelling open channel flow of Newtonian fluids. This has been done for modelling turbulent flow of low concentrated slurries with some success. However, this is not the case for highly concentrated slurries where the flow in the channel is no longer turbulent. Unlike Newtonian fluids, work carried out on flow of pseudo-homogeneous, non-Newtonian fluids in open channels is somewhat limited. Moreover, these results have been published in a variety of sources. This paper attempts to give a critical review of the work carried out on Newtonian and non-Newtonian flow of pseudo-homogeneous non-settling slurries in rectangular open channels. A comparison is also made of the models based on power law, Bingham plastic and Herschel-Bulkley fluids for laminar and turbulent flow in rectangular open channels.

Jan 1, 2007

By J. P. Beukes

South Africa holds approximately three-quarters of the world?s viable chromite ore resources and dominates the global production of ferrochrome. Albeit completely unintended, small amounts of Cr(VI) are formed during ferrochrome production. Certain Cr(VI)species are regarded as carcinogenic, hence making the treatment of some ferrochrome waste materials necessary. In this paper, the Cr(VI) treatment strategies currently employed by the South African ferrochrome producers are investigated by means of a literature review and a questionnaire survey. From the discussion, it is evident that various treatment strategies are available to deal with Cr(VI)-containing waste in the ferrochrome industry. However, by far the most commonly applied treatment strategy remains the aqueous reduction of Cr(VI) with ferrous iron. The advantages and the correct application of this strategy, together with the disadvantages and pitfalls, are argued. Innovative improvements on historic practices are also discussed

Jan 1, 2012

By Q. Li, B. Ricks

Over the last several decades mineral concentrate long distance slurry pipelines have been installed and successfully operated. Nearly all were installed via the buried construction method. Their record of depend ability and economy has been well proven. However, these systems operate in regions where seasonal soil frost penetration is shallow or non-existent. In recent years interest in long distance mineral concentrate pipelines in northern cold regions has been increasing. For cold regions one must consider seasonal temperatures and soil frost penetration in order to ensure reliable operations through the year. Herein a case study is developed where heat balance and temperatures for small and large diameter long distance slurry pipelines are compared. The study development is as follows: ?Rheological properties are analysed over range of temperatures from near freezing (4ºC; 39ºF) to relatively very warm (40ºC; 104ºF). ?Then assuming similar climatic conditions, soil properties, and pipeline length, a study is carried out for two pipeline diameters, namely: a small diameter (nominal8 inch; 219.1 mm) and a large diameter (22 inch; 558.8 mm). ?The study focus is on maintaining slurry temperature above freezing throughout the pipeline length by illustrating a decision based on burial depth versus coating the pipeline with insulation.

Jan 1, 2007

By P. J. Bartlett, H. A. D. Kirsten

A two-dimensional numerical scheme for the simulation of the plastic stress-strain properties of rock, and the various components of rock reinforcement and shotcrete, was used to rigorously determine the characteristics of tunnel support under squeezing conditions. D-shaped tunnels varying in size from 2,8 to 6,5 m in height and width were considered. The four main mining stages in the BAS block cave on Premier Mine were simulated as alternative sets of field stresses. The rock reinforcement comprised 1,8 m long fully grouted rockbolts and 6,0 m long fully grouted cable anchors at various spacings, and of various tensile and bond strengths. Various thicknesses of shotcrete and footwall support configurations were also considered. It was found that shotcrete and rock reinforcement, owing to inherent differences in stiffness, do not function in unison. As monolithic application, shotcrete has an overriding avidity for the imposed loading and destructs itself unless of extraordinary thickness. Under squeezing conditions, it accordingly supports the excavation surface while the rock reinforcement contains on-going convergence. The loads in the various support components can be determined only by simulation of the shotcrete as a stress-relieved medium to represent its broken condition in the field. The loads in the rock reinforcement vary around a tunnel and are the largest in the sidewalls. The loads increase with an increase in tunnel dimensions, the increase in load in the sidewall due to an increase in height being larger than that in the hanging- and footwalls due to an increase in width. Depending on the strength of the rock, the loads in the rock reinforcement become prohibitively large beyond a certain size of tunnel. The reinforcement of footwall rock can be omitted without adversely affecting that in other walls, provided the tensile and bond strengths of the reinforcement are not limited. The resulting footwall heave may, however, result in undermining of the reinforcement in the adjoining walls. A relative depth of anchor of 1,37 provides adequate bond strength in the larger sizes of tunnel, whereas, in smaller tunnels, anchor length is determined by the allowable convergence. The lack of fun column grouting adversely affects the efficiency of rock reinforcement to a major extent. The loads in rock reinforcement are very sensitive to the strength of the rock. Owing to a lack in refinement and calculational rigour, empirical classification systems are an inappropriate means for the design of tunnel support in squeezing conditions and, as a result, grossly unclear-estimate the support requirements.

Jan 1, 1992

By P. Pięta, A. Surowiak, T. Niedoba

In a flotation process of copper ore three factors were measured: copper grade in concentrate (β), copper grade in tailings (J) and recovery of copper in concentrate (e). The experiment was conducted by means of the Jameson cell. The factors influencing the quality of the process were particle size (d), time of separation (t), type of the collector (k) and dosage of the collector (s). The considered vector function was then [β(d, t, k, s), J(d, t, k, s), e(d, t, k, s)]. Optimisation achieved was based on determining the values of the adjustable factors (d, t, k, s). The goal was to obtain the highest possible values of functions β and e (maximum) and the lowest possible values of function J (minimum). To this purpose the taxonomic methods were applied. Keywords: Flotation, copper ore, lithology, flotation agents, particle size distribution, taxonomic methods

Jan 1, 2020

By J. J. Taute, G. Chisakuta, P. Bwando, G. Mitshabu

"BASF Mining Solutions have developed a new generation of copper solvent-extraction reagents that offer significant benefits over the existing reagents available to the industry today. Initial laboratory studies and pilot-plant trials have shown that these new reagents offer the benefits of a dramatic increase in resistance to degradation and are nitration-proof. This paper details a recent pilot-plant campaign at a commercial solvent-extraction plant. The main focus was to evaluate the copper/iron selectivity, copper recovery and net transfer of the new reagent compared with the conventional oxime reagents. The new reagent displays similar copper recovery and net transfer capabilities from typical agitation leach solutions. The pilot-plant results show a step change improvement in copper/iron selectivity in comparison with the existing modified and non-modified hydroxyoxime reagents used on the commercial plant. INTRODUCTION Copper solvent extraction (SX) from an acidic aqueous solution is typically accomplished using a hydroxyoxime extractant (Jergensen, 1999; Kordosky, 2000; Szymanowski, 1993). There are three hydroxyoximes from which all standard formulations are derived: 5-nonyl salicylaldoxime (NSAO), 5-dodecyl salicylaldoxime (DSAO) and 2-hydroxy-5-nonyl acetophenone oxime (HNAO). In the case of NSAO, it is necessary to use equilibrium modifiers in order to increase the copper stripped from the extractant (Kordosky & Virnig, 2003). Blends of DSAO, NSAO and HNAO are used to cover a wide spectrum of conditions (Kordosky, 2008). Use of modified aldoximes and reagent blends over the last 30 years has influenced the way copper producers and equipment manufacturers have approached the operation of copper plants. Existing solvent-extraction reagents cater for typical pregnant leach solutions (PLS) of copper mining systems which do not have significant effects on the reagent. Table I illustrates the range of copper concentration, pH values, temperature and iron concentrations for different leaching operations. As conditions become increasingly aggressive (i.e., higher PLS temperatures in primary sulfide leach or high iron content), current reagents become less capable of functioning according to expectations. One example is the effect of high iron (Fe3+) concentration in PLS and operating SX to achieve high copper recoveries. The ferric is partially chemically extracted and is transferred to elctrowinning (EW) during the stripping stage. To avoid a build-up of iron in electrolyte, which negatively affects current efficiency, a bleed of electrolyte is required. This bleed leads to excessive consumption of reagents, such as cobalt added to the EW process, and thus increases operational cost."

Jan 1, 2015