Search Documents

By Verne E. Hooker

Stress relief measurements were made at three underground test sites associated with the Henderson project, American Metal Climax, located in the rugged, mountainous region between Loveland Pass and Berthoud Pass on the Continental Divide in Colorado. Sufficient data were obtained to determine the three-dimensional stress ellipsoid for each site. The measurements were made at hole depths greater than one diameter of the mined opening; thus, calculated stresses are representative of premining in situ conditions. The vertical components of stress are in good agreement with overburden depth including the influence of mountain topography. Horizontal components of stress substantially increase with depth. These components are believed to be influenced by stresses presumably of tectonic origin. The largest measured principal stress was 5,900 psi at a depth of 3.708 feet. The predominant orientation of maximum principal stress for the determinations at greatest depth is in the NW-SE quadrants.

Jan 1, 1972

"""Hazard"" is the general expression used by safety engineers to denote risk, or the danger to property or human beings from the contingencies peculiar to different industries. Where a business, family, or individual is subjected to possible financial loss from any particular hazard, it is customary and is considered good practice to insure for reimbursement of possible loss. Accordingly, we take out insurance for earthquakes, for fire, for accidents, etc., and are charged a different premium for each. The premium rate is based on our relative exposure to the hazard in comparison to the total loss to our particular class of business in our geographical location over a given period.Insurance, then, must be considered as the experience of a group rather than of an individual, and any individual may be fortunate or unfortunate over stated periods. Through the law of averages, the probability of loss because of exposure to hazard is becoming more accurately measured as experience is accumulated and data are analyzed.Lion human life came to have a financial value in the eyes of the law, and employers were held liable for losses through accidents to employees while on duty, insurance companies began to underwrite the accident risks of the different employers and divided them into classes based on the amount of risk involved. Premiums for compensation insurance are based on relative exposure, which is measured by pay roll. The premium is rated in proportion to the severity of losses established by statistical studies.' It soon became evident that the accident experience of employers in the some industry varied widely; that is, there were good and bad risked in the same line of business. This resulted in ""experience rating"" of premiums, meaning thereby that an employer with experience in accident cost was premium rated in proportion to his losses over a stated period (usually three or more years)."

Feb 1, 1926

By M. L. Whisman

Several commercial processes for reclaiming used lubricating oil were duplicated on a laboratory bench scale. Laboratory tests were selected and in some instances modified to determine the physical properties of each oil produced. In addition, the hydrocarbon composition of some samples was determined using a liquid chromatographic technique, and compared with the composition of new oil in order to determine the severity of the re-refining technique. Selected samples of reprocessed oil were reformulated with an additive package for further estimates of quality as determined by wear, corrosion, foaming, and oxidation stability tests. Additionally, several samples of commercially re-refined oil and new oil were obtained and physical properties were determined for comparative studies.

Jan 1, 1974

By B. W. Jong

The U.S. Bureau of Mines investigated anhydrous chlorination and caustic-acid leaching processes to recover Ni, Co, Mo, and W from waste hydroprocessing catalysts. In batch laboratory-scale equipment, the chlorination process extracted 61 to 99 pet of the metals. Final recovery was 65 to 99 pct. The caustic-acid leaching process extracted 81 to 98 pct of the metals. Final recovery was 36 to 99 pct. Chlorination processing included roasting, chlorination, hydrolysis of metal chlorides for recovering Mo or W, water leaching of Ni or Co from the spent charge, purification, and solvent extraction or precipitation of Ni or Co from the purified solutions. Caustic-acid leach processing included NaOH leaching, solvent extraction of Mo or W from the NaOH leach liquor, H2S04 leaching of the NaOH leach residue, purification, and solvent extraction or precipitation of Ni or Co from the purified solution. The estimated fixed capital cost for a commercial-scale plant processing 39,000 Ibid of waste Ni-Mo-AI catalyst was $8 million for the chlorination process and $9.6 million for the caustic-acid leaching process. The estimated operating cost was about $0.20 and $0.40 per pound of the waste catalyst, respectively, for the two processes.

Jan 1, 1989

By H. Robert Ensminger

The Belizean economy had an estimated annual growth of about 3.4% over that of 1986. Economic growth during the 2 previous years was slower and was characterized by a negative trade balance. The gross domestic product (GDP) was an estimated $200 millioni2 in current dollars. Limited natural resources and scarce finances continued to make the Government's task a difficult one. Belize and China signed an economic cooperation agreement in April under which the Chinese Government is to provide technical assistance, a cash grant of $60.000, and a long-term, interest-free loan of approximately $1.5 million. In May, it was reported that gold was discovered in a remote area of the Maya Mountains in western Belize. An estimated unassayed value of $400 million has been placed on the deposit by one of its discoverers. However, the government in Belmopan has played down the discovery. Two U.S. oil companies. Seahawk Oil International of California and Alston Oil Co. of Texas, were granted licenses to explore for oil. Seahawk Oil will explore a large area of the Orange and Corozal Districts, while Alston Oil will prospect a 90,000-acre area of the western Cayo District. Another U.S. oil company, Pecten Oil Co., recently completed seismic studies off-shore of Belize City. Pecten Oil has made plans to start drilling in 1988.

Jan 1, 1989

By Maria I. De Rosa, Charles D. Litton

The U.S. Bureau of Mines conducted experiments for predicting materials' ease of combustion (smoldering onset, smoldering, flaming, and decomposition rates) by means of submicrometer smoke particle characteristics for the development of a simple test method. The experiments were carried out in an approximately 20-L furnace, with a 10-L/min airflow through the furnace for a 14-min duration, at set furnace temperatures of 150°, 250°, and 1,000°C. The variables studied as a function of time were the onset time of smoke particles, time and duration of maximum smoke particle generation, average concentration of smoke particles, and particles' average diameter, mass weight loss, and furnace temperatures. Results show that the onset time of smoke particles is predictive of materials' ease of smoldering, and the time of maximum smoke particle generation and its duration, coupled with mass weight loss, are predictive of materials' ease of smoldering and flaming (depending on the experimental temperatures), and decomposition rates.

Jan 1, 1992

By Charles Vaught

This is the second in a series of four articles that discuss underground firefighting preparedness. As with the first article in the May-June issue, it is based on interviews with 214 miners conducted at 7 underground mines (?A? through ?G?) by researchers of the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Center [Vaught et al. 1996].In the first article, the authors presented an overview of the study conducted by NIOSH on mine fire response preparedness and provided a general perspective on underground mine fires. In this article, we will describe miners? preparedness to evacuate a fire and their experience with incipient fires

Jul 1, 1997

Determine whether the total delay time in blasting may be safely increased beyond the currently permitted 0.5 s, without igniting a methane or methane-coal dust atmosphere and determine the minimum borehole spacing to avoid misfires. Approach At present, regulations limit the delay time used in short-delay blasting to a total of 0.5 s. Many in industry and government would like to see this total delay time increased to 1 5 to permit an increase in the number of different delays available for short delay blasting and an increase in the time between delay periods. The Bureau of Mines conducted research to determine whether the total elapsed delay time for blasting coal in underground mines could be safely expanded, with resulting improvements in productivity. The research was conducted at a surface mine in St. Clairsville, Ohio. Experimental shots were conducted in several pits, each of which had a 5-foot-high coal seam (Pitts-burg No.8) in a 50-foot highwall. The coal seam and a mobile gallery provided a good simulation of an underground coal face. The Bureau also examined the relationship between borehole spacing and misfires, to check on reports over the past few years that permissible explosives frequently misfire. These reports were not well documented, but were numerous enough to warrant investigation. Misfires of permissible explosives in an underground coal mine can be very hazardous; a burning cartridge of explosive may be ejected from a borehole and ignite the gas or dust in the mine, or a misfired cartridge in the muck pile may detonate during drilling and mucking operations, causing serious injuries.

Jan 1, 1986

By Forrest T. Moyer

Injury experience in the mineral mining and processing industries during 1968 was slightly improved in the nonfatal-injury record but worse in the fatality record. The resulting frequency rate of all injuries was slightly better, whereas the injury-severity rate retrogressed appreciably from the figure for 1967. Overall operating activity, as measured by man-hours of worktime, was slightly higher in 1968. However, there were several major segments of the mineral industries in which activity was lower owing to reduced demand for mineral products and to several major work stoppages. These statistics comprise the injury and work experience of all personnel engaged in production, exploration, development, maintenance, repair, and force-account construction work, including supervisory and technical personnel, and working partners and owners at mineral-producing and mineral-processing establishments in the United States. Data concerning officeworkers are excluded except for the oil and gas industry for which such information is not separable. All injury rates and totals are calculated from data before rounding. The data for 1968 are preliminary except for the anthracite, coke, petroleum and natural gas, native asphalt, peat, and slag industries, which are final. The figures represent full coverage for all industries except oil and gas for which coverage is not complete, particularly with respect to small companies.

Jan 1, 1970

By Janet Torma-Krajewski, Pauline Lewis, Paul Gust, Lisa Steiner, Kean Johnson

Since 1990 and the publication of the Ergonomics Program Management Guidelines for Meatpacking Plants by the US Occupational Safety and Health Administration, numerous reports of companies implementing ergonomics program have been published. However, despite these numerous reports, no examples of implementing an ergonomics program in the mining industry have been reported. In 2000, NIOSH initiated a long-term project to demonstrate the implementation of an ergonomics process designed to identify and reduce exposures to ergonomic risk factors found in mining. The mine selected for this project was the Jim Bridger Mine, a surface coal mine located 35 miles northeast of Rock Springs, Sweetwater County, WY. This paper discusses how a large, surface coal mine implemented an ergonomics program and the lessons learned while doing so.

By W. E. Robinson

Oil-shale samples selected from a core of the Green River Basin (Wyoming) were studied to ascertain differences in the composition and/or chemical structure of the organic material in the samples relative to stratigraphic position within the Green River Formation. This involved a systematic study of the soluble organic material and the insoluble kerogen present in the samples. Emphasis was placed upon the distribution of the alkanes (normal and isoprenoid compounds) in the soluble extract and upon the aromaticity of the kerogen. In general, it was concluded that significant differences exist in the chemical structure of the oil-shale organic material from various strata within the Green River Formation of Wyoming. Most of the compositional and structural changes were not related to burial depth but were related to source material variations, environmental differences, or other factors.

Investigate and demonstrate the possible use of low-density (45-lb/ft3) foam concrete for sealing abandoned mine openings. Although foam concrete has been used in the construction and geotechnical industries for some decades, it has not previously been used in abandoned mint shaft reclamation. Approach A structurally engineered permanent mine seal for an abandoned coal mine shaft, using low-density foam concrete and other appropriate structural materials, was designed by the Bureau and installed at a field site, the No. 22 Shall in Logan County, West Virginia. The field work was conducted by a private contractor under the supervision of the West Virginia AML Section (WV AML). The No. 22 Shaft is situated immediately adjacent to a frequently traveled county road. A few feet away from the shaft is a branch of Pine Creek. On the other side of the road is a railroad line that serves an active mining operation located several miles away. The shaft measures 9.5 by 9 feet in cross section and is about 300 feet deep. It was used at one time as a dewatering shaft and still contains two large-diameter dewatering pipes with steel drive shafts inside them. Before the beginning of the reclamation, the shaft included a concrete cap a few inches thick, with a 4 - by 5-foot access opening covered by a steel grate. The interior of the shaft was quite humid, and considerable flow of water at the bottom of the shaft could clearly be heard from the surface. Methane tests were conducted that showed the shaft to be clear of this gas.

Jan 1, 1992

To enhance safety and efficiency when moving large mining equipment under energized trolley lines, and to assist in compliance with Section 75.1003.2, 30 CFR. Approach A system was designed, using established technology, that permits a remotely located circuit breaker to be controlled from the cab of a mine locomotive moving large mining equipment under energized trolley lines. This control consists of setting the desired trip current, automatic or manual tripping, resetting, and voice communications between the locomotive and a remote Circuit breaker location. How It Works According to 75.1003.2, 30 CFR, whenever a piece of off-track equipment (such as a longwall chock or a continuous miner) is moved by rail under energized trolley or feeder lines, power for the locomotive that is moving the equipment must come from only one' circuit breaker. This circuit breaker must be adjusted to permit no more than one-half its rated short-circuit current to flow. The intent is to lessen the danger if an accident should occur, and if the equipment contacts the trolley line. Even so, the danger is great. This half setting can still represent many hundreds or even thousands of amperes, enough to endanger personnel, the equipment, or the mine. The Remote Control System reduces this danger substantially by giving the personnel associated with the move total control over the associated circuit breaker. The system as designed, is intended to be used with portable circuit breakers that are pulled on a small flat car by a mine jeep, and either precede or follow the equipment, depending on the direction of the power. This portable circuit breaker is equipped with a commercially available solid state overcurrent relay and associated shunt. This circuit breaker is connected via heavy duty clamps around an open trolley line tie breaker such that the current through the shunt is also the current in the trolley line. A receiver, interfaced with the overcurrent relay and shunt, completes the remote system.

Jan 1, 1981

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine if the primary gas toxicities evolved during the early (-300° C) and later (>400° C) combustion stages of mine conveyor belts could be predicted by a smoke particle characteristic. The experiments were conducted in an approximately 20-L furnace at set furnace temperatures of 150°, 250°, and 1,000° C, with a furnace airflow of 10 L/min. The variables studied, as a function of time, included hydrogen chloride and carbon monoxide concentrations, the average smoke particle diameter (d8 and number concentration (no), and the product of the average smoke particle diameter and concentration (dgn0) Other variables included the sample and furnace temperatures and the sample mass weight loss. Results show that the inverse of the smoke particle diameter-concentration product (ldgn0), correlates directly with the hydrogen chloride and carbon monoxide toxicities released in large quantities during the early and later stages of combustion.

Jan 1, 1989

Improve face ventilation in mines with large cross-sectional entries. Approach Oil shale, salt, and limestone mines typically have large entries. Providing adequate airflow to the working faces of such mines for worker comfort, health, and safety is a substantial ventilation problem. If diesel equipment is used at the face or if a methane hazard exists in the mine, the problem becomes even more complex. To address this problem, a study was conducted under a joint contract between the Oil Shale Committee of the Colorado Mining Association and the Bureau of Mines. The study evaluated two face-ventilation concepts for large-entry mines. Improving Ventilation Two face-ventilation systems were selected for testing of an oil-shale mine, based on results of a cost/benefit analysis. The systems were a free-standing jet fan and a ducted fan operating in the blowing mode. The jet fan was spotted on the intake side in the mouth of the entry being advanced with final positioning, in or out, deter-mined by minimum recirculation. The ducted fan was also positioned in the mouth of the entry being advanced, with its tubing terminating 75 feet from the working face. The mine face entry was a dead heading 55 feet wide, 30 feet high, and 320 feet long. Sulfur hexafluoride (SF.) tracer gas was used to measure the performance of the two systems in diluting mine face pollutants including after-gases from blasting, hot diesel emissions, methane roof layers, and methane emitted from muckpiles.

Jan 1, 1987

By H. J. Sloman

"INTRODUCTION Industry, including coal mining, has come to realize that to prevent accidents the human element must be given more consideration than was customary in the past. In formulating safety rules and regulations and in the enactment of laws governing mining, too often enforcement is emphasized rather than the means of gaining willing compliance.' The purpose of this paper is to call attention to the human side of accident prevention, and the approach to this important and much-discussed subject will deviate somewhat from the usual discussions.The human being is a complex mechanism, both physically and mentally. It is difficult to establish a common denominator for the actions of humans, except in general. In establishing mining laws, rules, regulations, and standards, the ultimate objective should be to gain the best possible response of workmen, so that optimum results in accident prevention may be obtained. The complexity of human beings is apparent when the many ways 1n which they differ are considered. Some of these differences are manifested in emotional and phlegmatic types, degrees of intellect or native intelligence; and in hopes, desires, aspirations, and philosophies of life. How much simpler ac¬cident prevention would be if the response to laws, rules, regulations, or standards were equivalent to the definite movements of puppets responding to pulls on strings. Each time, the strings are pulled in exactly the same way, the puppets will respond in exactly the same manner. Human beings, although having many similar characteristics, do not respond uniformly to identical ""string-pulling""; therefore, much study is necessary before the desired re¬sponses can be obtained. To achieve the ultimate in accident prevention, it must be ""worked at"" constantly. Regardless of the adequacy of safety laws, rules, regulations, or standards, good accident records will not ""roll in"" if dude consideration is not given to the personal traits of those most likely to be involved in accidents."

May 1, 1948

By Yael Miron

ANFO blasting agents may undergo an exothermic reaction when they contact warm ore bodies that contain pyrite and its weathering products. The reaction is very fast at temperatures above 80° C. Urea, when present in sufficient amounts, inhibits this reaction at temperatures below 180° C. But urea-ammonium nitrate mixtures are very hygroscopic and, in certain climates, may be difficult to handle in the field. Reaction-inhibiting characteristics of three compounds were reported by the Bureau of Mines in 1979. Recently, the Bureau investigated the reaction-inhibiting qualities of five additional compounds. Mixtures of ANFO, pyrite, weathering product, and prospective inhibitors were slowly heated, under conditions simulating a hot borehole, to determine prospective inhibitor capability at temperatures up to ~175° C. Small-scale thermal tests of the same mixtures were used for verification and clarification of results. Two organic compounds, phthalimide and xanthine, similar in structure to urea, failed to inhibit the reaction. Zinc oxide and calcium carbonate were found inferior to urea, though zinc oxide raised the onset of reaction from 80° C to about 140° C. Only magnesium oxide was found to be similar to urea in its inhibitory ability at temperatures below 175° C. Based on results from analysis of quenched residues, the use of more than 5 wt-pct magnesium oxide is recommended.

Jan 1, 1982

By Paul T. Allsman

SCIENTIFIC inquiries concerning phenomena that may influence mining technology were widely publicized during the year. The deep-hole drilling project "Moho," 3 the use of nuclear explosives underground, and the recovery of minerals from the depths of the sea became subjects of scientific and general discussion. The mining industry continued to watch these developments with keen interest: but its more immediate concern was the increasing tempo of competition between mineral commodities, the domestic producers of these commodities, and foreign sources of supply. The competitive situation has intensified the industry's efforts to develop more efficient new mining methods, as well as to improve the efficiency of present practices. The attitude of the industry was well illustrated by rapidly expended use of low-cost ammonium nitrate explosives, the establishment of rigid schedules for equipment maintenance, and close attention to the detailed costs of production. The complexity of planning a new coal mine is aptly illustrated by the editors of Mechanization in the April 1959 Issue, in which they outline the cost of developing a mine and the various problems, factors, and decisions involved.4

Jan 1, 1960

By C. M. Frost

Crude shale oil produced during in situ retorting by the Bureau of Mines at Rock Springs, Wyo., was refined by three schemes. In the first, the crude oil was fractionated to raw naphtha and 400° F+ residuum. The residuum was hydrogenated over cobalt molybdate catalyst at 815° F and 1,100 psig. The blended raw and 160°-400° F hydrogenated naphthas were hydrodenitrified and then catalytically reformed. The 400° F+ hydrogenated oil was catalytically cracked. In the second scheme, the crude was hydrogenated over nickel-tungsten catalyst at 800° F and 1,500 psig. The hydrogenated fractions were processed by methods used in the first scheme. The third scheme resembled the second but, prior to hydrogenation, the crude was "hydrostabilized" over cobalt molybdate at 500° F and 500 psig. Yields of reformate and cat-cracked gasoline as volume-percents of the crude, and research-method octane numbers (with 3 ml TEL) for the three methods were as follows: First method, 32 pet reformate, 90 octane; 19.5 pct cracked gasoline, 99.2 octane. Second method, 29 pet reformate, 81.1 octane; 21.3 pct cracked gasoline, 99.6 octane. Third method, 28.2 pet reformate, 86 octane; 28.7 pct cracked gasoline, 95.9 octane.

Jan 1, 1974

By Basil Dimitriades

Five recently developed methods for determining nitrogen oxides in automotive exhausts have been evaluated from the standpoint of accuracy and applicability in current exhaust studies. Results showed that methods requiring conversion of nitric oxide to nitrogen dioxide as a part of the analytical procedure are subject to errors introduced by the instability of NO2. The extent of some of these errors has been determined and procedures have been developed to minimize undesirable influences. On the basis of the results obtained from this study, recommendations are made regarding procedures for batch type or continuous measurement of nitrogen oxides in exhaust streams.

Jan 1, 1968