Search Documents

By B. H. Eccleston

The Bureau of Mines, in cooperation with the American Petroleum Institute, studied the effect of fuel volatility and front-end fuel composition on the amount and photochemical reactivity of automobile exhaust and fuel-system evaporative emissions. The study involved six gasolines--the base fuel, three fuels of varied volatility, and two fuels differing from the base and from each other in front-end olefin content. Data were obtained from 16 vehicles operated on a chassis dynamometer using a speed-load-time cycle that approximated a typical urban trip. Tests were made at ambient temperatures of 20°; 45°, 70°, and 95° F, using a climate-controlled dynamometer room. The amount of hydrocarbon emission and its probable photochemical effect, a potential contribution to pollution, is expressed as weight (reactivity equivalent) of a moderately reactive material, ethylene. Emissions of oxides of nitrogen, car-bon monoxide, and aldehydes were also observed. Results showed that reduction of volatility from currently typical levels serves to reduce both the amount and the reactivity equivalent of evaporative losses with a slight penalty by way of higher exhaust emissions. Alternatively, reducing the amount of light (low boiling) olefin in the fuel had no effect on the amount of hydrocarbon pollutant but did significantly reduce the reactivity equivalent of the emissions. Neither volatility change nor chemical changes to the fuel significantly affected the nonhydrocarbon emissions.

Jan 1, 1970

By Stephen D. Cramer

The Bureau of Mines conducted a series of in situ linear polarization measurements in high-temperature, high-pressure hypersaline geothermal brines at the Bureau of Mines Geothermal Test Facility in the Imperial Valley of California. The measurements represented an evaluation of the linear polarization technique for obtaining instantaneous corrosion rates of materials of construction in flowing hypersaline hydrothermal fluids that rapidly form scales on exposed surfaces. A special method was devised for use with the linear polarization technique that resulted in obtaining corrosion rates for 1020 carbon steel, 316 and 430 stainless steel, titanium, various nickel-based alloys, and aluminum 6061 under strong scale-forming conditions. The measurements also provided information on scale-deposition rates in various geothermal environments. Exploratory in situ potentiostatic polarization measurements were made in the flowing brines to qualitatively determine scale-deposition effects on the electrochemical measurements.

Jan 1, 1978

By R. D. Saltsman

Under contract with the Federal Bureau of Mines, Bituminous Coal Research, Inc., performed a statistical study to find less expensive and time-consuming methods of monitoring the noncombustible content of coal mine dust. Calculations based on thermodynamic considerations verified the reasonableness of Federal rock-dusting requirements. The results of extensive sampling in southwestern Pennsylvania mines indicated that, at the 95-percent confidence level, the present system of sampling at 200-foot intervals may be replaced by sampling at 500-foot intervals, and that a 1-inch scoop floor sampler may replace the standard 6-inch scoop for floor sampling. Further field testing is recommended.

Jan 1, 1975

By M. Kanda, W. D. Bensema, J. W. Adams

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating coal mine, Itmann No. 3 Mine, located near Mullens, West Virginia. The electromagnetic environment created by 250-volt-dc and 550- and 950-volt-ac machinery in two longwall panels was measured and is reported. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. It is recorded using broadband analog magnetic tape, and the noise data is later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 6, 1974

By S. P. Kinney, A. C. Fieldner, S. H. Katz

"1 Introduction The regrettable death of James S. Cunningham, Foreman Miner, attached to Bureau of Mines Rescue Car No. 2, while wearing a half-hour type oxygen breathing apparatus in a gasoline storage tank at Trinidad, Colorado, raised the question as to the possibility of gasoline vapors permeating the rubberized fabric of the breathing bags of such apparatus.It is known that most gases and especially certain organic vapors permeate rubber, by solution or a similar process. The rubber becomes saturated with the gas and if a concentration of gas is maintained on one side of the rubber sheet it slowly gives off gas from the other side. It of course takes some time for the gas to diffuse through the rubber and the length of time before it reaches the other side is proportional to the thickness of the rubber. The amount of gas that passes through per unit of area in unit time increases with the concentration of gas and also varies with the structure and composition of the rubber.It has been suggested that the gasoline vapor could not have penetrated into the interior of an oxygen breathing bag because the pressure is greater on the inside, but this is not true as the process of permeation by solution in the rubber is affected only by the difference in the partial pressures of gasoline vapor on the inside and outside of the bag. The positive oxygen pressure on the inside can only prevent the entrance of gasoline vapor through measurable holes, and has no effect on permeation by diffusion through the rubber."

Dec 1, 1919

By W. H. Ode

Low-temperature distillation tests at 200°, 350°, and 500° C. were made on a subbituminous coal from Boulder County, Colo., and a subbituminous coal from Weld County, Colo., in connection with a survey of carbonizing properties of American coals4/ and. investigations of their chemical and physical properties.5/ The coal represented by the sample from weld County was reported to give off combustible volatile matter at unusually low temperatures when placed on a fuel bed. The yields of tar and oil and the composition of the gas from this coal, as obtained in the distillation tests, did not confirm this report. These yields and the gas composition of the Weld County coal differed but little from those obtained from the coal from Boulder County. Both coals yielded tar and gas in amounts considered to be normal for coals of their rank.

Jan 1, 1937

By S. P. Kinney, A. C. Fieldner, S. H. Katz

"The regrettable death of James S. Cunningham, Foreman Miner, attached to Bureau of Mines Rescue Car No. 2, while wearing a half-hour type oxygen breathing apparatus in a gasoline storage tank at Trinidad, Colorado, raised the question as to the possibility of gasoline vapors permeating the rubberized fabric of the breathing bags of such apparatus.It is known that most gases and especially certain organic vapors permeate rubber, by solution or a similar process. The rubber becomes saturated with the gas and if a concentration of gas is maintained on one side of the rubber sheet it slowly gives off gas from the other side. It of course takes some time for the gas to diffuse through the rubber and the length of time before it reaches the other side is proportional to the thickness of the rubber. The amount of gas that passes through per unit of area in unit time increases with the concentration of gas and also varies with the structure and composition of the rubber.It has been suggested that the gasoline vapor could not have penetrated into the interior of an oxygen breathing bag because the pressure is greater on the inside, but this is not true as the process of permeation by solution in the rub¬ber is affected only by the difference in the partial pressures of gasoline vapor on the inside and outside of the bag. The positive oxygen pressure on the inside can only prevent the entrance of gasoline vapor through measurable holes, and has no effect on permeation by diffusion through the rubber.A sample of gasoline was obtained from the tank in which Cunningham met his death. Examination by Dr. E. W. Dean of the Petroleum Division of the Bureau of Mines gave the following results.This shows the gasoline to be heavy and typical of the gasolines sold throughout Colorado for motor fuel A. Salvus half hour oxygen apparatus was arranged with the breathing bag only in a gas tight box in which the space was kept saturated with the vapor of this gasoline. The main part of the apparatus was outside the box. Oxygen from the apparatus was breathed by a man in the usual manner. Gas samples were taken from the box at intervals to determine the concentration of gasoline vapor, also samples of the oxygen breathed were taken from a side tube in the mouthpiece. The room temperature was 75°F. The concentration of gasoline vapor in the box at the beginning of the test was 4.3%. The man breathing from the apparatus thought he detected gasoline in his oxygen in two minutes after starting the test. Analysis of the inspired oxygen at this time showed 0.03% gasoline vapor. The same man remained on the apparatus for 18 1/2 minutes without suffering any ill effects. His place vas then taken by another man who wore the apparatus until the oxygen was exhausted without noticing more than a trace of gasoline at any time. At the end of the test the inspired oxygen contained 0.07% gasoline vapor. The total time of test was 38 minutes."

Dec 1, 1919

By William C. McBee

Prompted by forecasts of a sulfur oversupply, the Bureau of Mines, U.S. Department of the Interior, is conducting research on potentially large-scale uses of this commodity to extend or replace such construction materials as asphalt, cement, and mineral aggregates. Through these efforts, paving materials have been developed in which sulfur replaces up to 50 pct of the asphalt normally present and which can be prepared and placed with existing mixing and paving equipment. Laboratory properties and design methods for this direct mixing process are described along with properties obtained on small-and large-scale field demonstration projects. These properties are compared with those obtained from control materials prepared without sulfur additions. Monitoring for toxic gases during laboratory and commercial mixing and paving operations is discussed also.

Jan 1, 1978

By M. G. Zabetakis

Amyl nitrite (C5H11NO2) is a pale-yellow liquid with an ethereal fruity odor and a pungent aromatic taste. Its use in first-aid treatment of cyanide poisoning has been suggested by Chen and his coworkers. Although not the most effective treatment, it is the only one that does not require intravenous injections and is, therefore, very suitable as a preliminary measure, which only involves breaking a capsule near the patient's nose until intravenous injections can be given. In the case of the sodium nitrite -sodium thiosulfate treatment, for instance, such injections require about 15 minutes. As amyl nitrite "Pearls" (small capsules containing liquid amyl nitrite) are placed in many first-aid kits by various companies that handle, store, or use hydrogen cyanide gas, it appeared advisable to investigate the explosion hazards of this material in air and oxygen. Accordingly, tests were made to determine the limits of flammability, temperature range of flammability of amyl nitrite saturated with air and with oxygen, and minimum ignition temperatures of this material in air and in oxygen.

Jan 1, 1952

By Sean Gallagher, Thomas R. Battenhouse, August J. Kwitowski, John R. Bartels, Dean H. Ambrose

Problem: Incident investigation reports do not usually contain enough information to aid in studying boom arm vertical speed for roof bolting machines to determine the impact that appendage speed had on an operator's risk of experiencing a contact. Laboratory experiments with human subjects are also not feasible because of safety and ethical issues. Method Researchers successfully developed a three-dimensional computer model that uses virtual human simulation software as the primary means to gather contact data when the boom arm touches the operator's hand, arm, head, or leg. Results: Data analysis of roof bolter simulations shows that the speed of the boom arm is the most important factor in determining the risk of an operator making contact. Regardless of other variables, contact incidents were always greater when the bolter arm was moving up, greater on the hand, and greater for the boom arm part of the machine. The reason why the subject experiences more contacts when the boom arm is moving up rather than down is that more risky behaviors occur during drilling and bolting when the boom arm is ascending. Based on the data collected, boom speeds greater than 13 in/sec result in a substantial increase in risk to the roof bolter operator of making contact. Speeds less than or equal to 13 in/sec are associated with a more modest relative risk of making contact, which represents a decrease in potential hazard. Impact on Industry: The use of such information can be quite helpful in making recommendations to machine design and task procedures to reduce the likelihood that roof bolter operators will experience injury due to contact with a moving roof bolting machine's boom arm.

By K. K. Kershner

Important contributions can be made to conservation of natural resources by recovering mineral values from primary and secondary metallurgical slimes and flue dusts. This applies particularly to ultrafine mineral particles that escape recovery by conventional mineral dressing. In the interest of economy and conservation the Bureau of Mines is investigating fundamental properties of ultrafine mineral values in slimes as a means of developing new or improved methods of mineral recovery. The work described in this progress report was carried on in the Bureau's laboratories at Rolla, Mo., from 1951 to 1953. The mineral material used as a subject for study was tin-ore slimes. DESCRIPTION OF TIN SLIMES The tin slimes consist principally of quartz, with appreciable quantities of tourmaline and sericite mica and small amounts of cassiterite, pyrite, hematite, and arsenopyrite. The tin content is approximately 0.5 percent.

Jan 1, 1954

By Stephen R. Wilson

This paper is one of a series published by the Bureau of Mines on the mineral resources of the Nation. It describes briefly the occurrence of sodium sulfate in Salt Lake and Tooele Counties, Utah, presents data on sampling, and describes ex-traction and refining raw material and a mining research project that has been conducted on the deposits. ACKNOWLEDGEMENTS Acknowledgments are given to the Tintic Standard Mining Co., Salt Lake City, Utah, and Bartlett Chemicals, Inc., New Orleans, La., for permission to use data obtained by the companies. The authors also acknowledge the courtesy of J. A. Marsh and H. K. Thurber, geologists and mining engineers, for permission to use information in reports prepared by them.

Jan 1, 1957

By G. W. Eiger

Bureau of Mines laboratory tests show that ilmenite concentrates with titanium dioxide contents as low as 33 wt--pct can be beneficiated to produce a crystalline substitute for natural rutile suitable for direct chlorination. The synthesized product prepared by a three-step procedure was comparable with natural rutile in titanium content. Reduction smelting of ilmenite removes iron as a pig iron byproduct, and the remaining slag phase is greatly enriched in titanium. Oxidation of the slag in the presence of phosphorus¬bearing slag additive converts the titanium-bearing phases to discrete rutile crystals and a glass phase containing most of the associated impurities. Rutile is separated from the glassy impurities by attrition scrubbing ground slag in dilute phosphoric or sulfuric acid solutions. Tests made in a laboratory fluid-bed reactor show that synthetic rutile responds to chlorination at the same rate as natural rutile and that more than 95 pct of the titanium contained in the feedstock was extracted as titanium tetrachloride.

Jan 1, 1974

1. Alford, N.G. quantity, of timber used in soft-coal mines and how much will be needed for the future. Gives a table of estimated increase in mine timber consumption in the future. A.I.M.E. Separate. 1336-C 1924. 2 Clark, B.M. The forest and the mine. Rept. Conference of Wood-Using Industries, Harrisburg, Pennsylvania. Apr. 13-14, 1921, pp. 58-62. Describes experience of a Pennsylvania mining company in depletion of timber supply and conservation methods adopted.

Jan 1, 1925

By H. V. Makar

A study was conducted by the Bureau of Mines to determine problems associated with the use of ferrous fractions from urban refuse as melting stock for steelmaking and to evaluate the resulting steel products. The study involved 50-pound ingots from laboratory melts and 50-pound ingots from 1-ton electric-arc-furnace melts. The 50 pound ingots from the laboratory melts and the arc-furnace melts were hot rolled to provide material for mechanical and corrosion testing. Results obtained in the study include the following: Most steels rolled successfully and exhibited acceptable surface and edge condition. Tensile strengths of the plain carbon steels were not significantly affected by copper up to concentrations of 0.65 pct and were not affected by tin content up to 0.16 pct. Yield strength increased with increasing copper and tin contents, and impact strength decreased with increasing tin content. Hardness increased slightly with increasing copper content. In general, properties of the steel produced were not measurably affected by charge composition (that is, melting stock), melting practice, or method of scrap preparation.

Jan 1, 1975

By George J. Conroy

This Bureau of Mines publication describes several fault locators and methods, including time domain reflectometers, a frequency domain reflectometer, tone generators, an infrared method, the Murray loop method, and high-voltage "click" methods. The Bureau of Mines has been conducting research into these methods for several years, to improve mine safety and facilitate production through rapid, safe location of trailing-cable faults. The problems encountered in practical applications are discussed, and schematic diagrams of several instruments fabricated by the Bureau are presented. Since no present single method of locating trailing-cable faults is universally applicable, a kit composed of several of the more promising fault locators is advisable.

Jan 1, 1978

By M. M. Tilman

The Federal Bureau of Mines developed a rolling method that improves creep resistance and yield strengths of lead alloys containing up to 5 wt-pct Sb. The 0.69-inch-thick slab-cast alloys were breakdown-rolled to 0.226 inch and finish-rolled to 0.063 inch at 5-or 20-pct reduction per pass. Rolling was at room temperature to simulate conventional cold rolling, and at 75°, 125°, and 175° C. Two alternative methods evaluated consisted of (1) a single cold final pass followed by annealing and (2) a single hot final pass. Two additional processing methods involving percipitation strengthening were included for comparison. Compared with conventional cold rolling, hot rolling at 125° and 175° C with multiple light passes vastly improves creep resistance and raises yield strengths. Tensile strengths are less affected. The other treatments also improve creep resistance significantly and generally improve tensile properties; magnitudes vary with treatment and composition.

Jan 1, 1975

By H. B. Carroll

The Bureau of Mines has designed and built a controlled-environment test chamber specifically for instrument evaluation in simulated work atmospheres. The atmosphere inside the 300-liter stainless steel chamber can be controlled at any selected temperature and relative humidity in the range of 2° to 93° C and 20 to 95 percent, respectively. Instruments placed inside the test chamber are subjected to an atmosphere at a preset temperature and humidity containing various concentrations of toxic gases such as CO, C02, NO, NO2, S02, and H2S. Toxic gas losses resulting from wall reactions, monitoring instruments, and instruments under evaluation are compensated by the use of a dynamic gas blending system.

Jan 1, 1973

By Martin H. Stanczyk

Two methods of recovering zinc from zinc ammonia complex solutions were investigated. One method studied was distillation of the ammonia from the solutions to recover a basic zinc sulfate, which after calcining to zinc oxide was reduced to metallic zinc using hydrogen at 900° C. The second method tested was electrolysis. The tests were made of synthetic and leach solutions analyzing about 80, 100, and 115 gpl (grams per liter) of Zn, NH3, and SO4, respectively. The leach solutions were prepared by oxidation leaching of a sphalerite flotation concentrate, assaying 55 pct zinc at elevated temperature and pressure. The distillation method recovered about 98 pct of the zinc in a product analyzing 97 pct zinc. Ammonia losses incurred during the leaching and distillation operations were about 0.1 lb per lb (pound per pound) of metallic zinc produced. Electrolysis of the solutions at a cathode current density of 25 amp per sq ft (ampere per square foot) yielded zinc deposits assaying in excess of 99.9 pct zinc. About 1.5 kwhr (kilowatt-hour) of power were consumed per pound of zinc deposited; the current efficiency was 72 pct. Other electrodeposition tests revealed that small amounts of ferric iron in the cell liquor were deleterious to electrolysis unless about 5 lb of glue per ton of zinc were present in the electrolyte. The use of glue and vigorous agitation of the electrolyte gave smooth zinc deposits from solutions containing as much as 0.1 gpl iron.

Jan 1, 1962

By Verne S. Mutton, William A. Slivensky, Eric S. Weiss, Kenneth L. Cashdollar, Deepak R. Kohli

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, cooperated with Tecrete Industries Pty. Ltd. and BHP Australia Coal in a research program to evaluate the strength characteristics and air leakage of four seal and two stopping designs for use in underground coal mines. A fundamental safety research area for NIOSH is to eliminate the occurrence of coal mine explosions or to mitigate their effects. One approach to achieve this goal is to develop new and innovative seal designs that provide increased explosion isolation protection for the mining personnel against ignitions that originate from within the gob or. other worked-out areas of the mine Full-scale seals and stoppings were constructed in the Experimental Mine at Lake Lynn Laboratory near Fairchance, Fayette County, PA. They were ail--leakage tested, then subjected to a series of explosions with average pressure pulses ranging from 25 to 500 kPa (3.5 to 72 psi). Instrumentation measured seal displacement and acceleration as a function of time, providing data to assist in the development of numerical models 1'01- future seal design. All three seals designed with Meshblock wire forlnwo~-k ant1 a lnonolithic shotcrete core withstood the first explosion test, which generated an avcr-age rnaximu~n pressure of - 140 kPa (-20 psi) while maintaining acceptable air leakage rates. These seals I-anged from 175 to 325 mm thick. They included a 2.7-m-high by 325-mm-thick seal that was tesled 27 hr after completion against this - 140-kPa explosion pressure, a special requirement of the test program. This seal survived explosions with pressure pulses up to 300 kPa (43 psi). The 2.3-m-high by 325-mm-thick Meshblock seal survived three explosion tests with overpressures up to 455 kPa (66 psi) and satisfied the air leakage criteria. A I ,200-mm-thick plug seal was constructed of two Gunmesh formwork walls in-filled with shotcrete and a 3,450-kPa (500-psi) strength Aquablend core. This plug seal survived three explosions with pressure pulses ranging 11-om 150 lo 430 kPa (-22 to 62.5 psi) with no measurable postexplosion air leakage. Two Gunmesh stoppings with thicknesses 01' 40 and 75 inln withstood explosion overpressures of 23 and 115 kPa, respectively. Anchoring all seal and stopping designs into the roof, ribs, and floor with steel "rootbolts" provided very effective boundary constraint that is critical to the performanceofstructures subject to explosion overpressures.

Jan 8, 1999