Search Documents

By Annie G. Smelley

The Bureau of Mines, U.S. Department of the Interior, as part of its mission to effect pollution abatement, conducted research to devise means for disposing of phosphatic clay wastes and reclaiming mined land. Part of the investigation was performed in a cooperative research project with 10 phosphate companies in Florida. The colloidal properties of the phosphatic clay suspensions, called slimes, make them difficult to dewater and dispose of without impoundment storage aboveground. Various reagents to flocculate and dewater these plant wastes were evaluated, and a polyethylene oxide polymer was found to function in a specialized flocculation dewatering technique. The flocculation dewatering method was investigated in bench-scale batch tests and applied in continuous dewatering tests using standard mineral-processing equipment. In continuous tests at feed rates of up to 58 liters per minute, wastes at 4 percent solids were dewatered to about 20 percent solids. About 0.8 kilogram of polymer was used for each metric ton of dry waste clay solids; processing time was about 4 minutes. Requirements for the treatment system are (1) proper mixing of the clay-waste feed and flocculant, (2) rapid removal of water as it is released, and (3) physical manipulation to promote cohesion of solids.

Jan 1, 1979

By D. B. Dow

The study of oil production methods with reference to the amount of oil originally pressent in the oil-bearing, formations has developed the fact that-ordinary methods-of production remove only a part of the oil actually present. In fact, it is generally realized that when a field is abandoned more oil remains in the sand than has ever been removed. As a consequence of this realization, the petroleum engineer has devoted considerable tine in recent years in devising methods for increasing the percentage of recovery. His studies have indicated that in most cases the total production of a field is dependent upon the available gas rather than upon the available oil. Mien the gas in the sand is exhausted, oil production ceases even though there may be enormous quantities of oil remaining unrecovered. Consequently, any method of conserving the gas or increasing the supply of gas will increase the ultimate recovery from a field. The practice of producing oil under vacuum increases the effectiveness of the gas remaining in the sand, as well as furnishing more gas by evaporating the light fractions of the crude. Pumping ' compressed gas or air down selected wells of a lease has been found to increase the production of oil from the surrounding wells. Studies of oil and gas ratios have indicated that much of the available gas has been wasted as far as its effectiveness on oil production is concerned. his has led to the development of "stop cocking"3 and the practice of producing under back pressure3, which methods aim, to obtain more effective work from the gas with reference to the amount of oil delivered to the well.

Jan 1, 1926

By Walter C. Lorenz

Samples of materials containing pyrite from various coal mines and coalbeds were studied to compare their compositions and oxidizing characteristics. Pyrite was the only form of iron sulfide identified, but X-ray diffraction, emission spectrography, and microscopic analyses revealed similar suites of minerals and trace elements. The pyrite occurred usually in spherical clusters of very small crystals. The oxidation of pyrite in solutions of PeSO4 and Fe2(SO4)3 and in the presence of an iron oxidizing bacterium Ferrobacillus ferrooxidans, was studied through a manometric technique. FeS04 or Fe2(SO4)3 solutions had no appreciable influence on pyrite oxidation under the test conditions, The bacterium acted as a catalyst, greatly increasing the oxidation rates; however, in three samples that also contained calcites, bacterial oxidation was greatly reduced. The oxidation rates also increased approximately as the percentage of pyrite in the samples increased. For the series of samples studied, there was no definite correlation of the results with the location of the various mines nor with the acidity of alkalinity of the mine drainage.

Jan 1, 1963

By B. F. Naylor

"INTRODUCTION Investigation of the physical properties of electrolytic manganese and its alloys has constituted a part of the program of the Bureau of Mines for several years, and already extensive data have been reported. 3-14/ Heat-content measurements above 25° C. of pure manganese 15/ were completed recently at the Pacific Experiment Station of the Bureau, and the results obtained removed many of the inconsistencies in previously reported data. This paper reports heat-content data of seven manganese-copper alloys, varying in composition from 25 to 90 percent man-ganese. The alloys, obtained from the Salt Lake City Station, 16/ had been quenched from 850° C, and cold-worked. Without further heat treatment, heat-content measurements of each of these alloys were made at 100° or less temperature intervals from 450° to 850º C., as it was considered likely that any abnormal behavior of the specific heat would be found in this temperature range. Also, a portion of each alloy was heat-aged at given temperatures for periods of time thought sufficient to reach phase-equilibrium; then the heat-contents above 25° C. were determined at the aging temperatures. (Heat-aging was done at approximately 450°, 550°, 650°, 750°, and 850° C.)METHOD AND MATERIALSThe heat contents were determined by the ""drop"" method in a previously described apparatus. 17/ The calorimeter was cali-brated with electrical energy, measured in international joules, and the results were converted to the conventional thermochemical calorie by the relation, 1 cal. = 4.1833 int. joules."

Jan 1, 1946

By L. J. Froisland

The Bureau of Mines conducted a 4-year research program at Uravan, Colo., on a 2-1/2-acre reclamation plot on the slope of a uranium tailings pile that had been covered with mine waste rock. The purpose of this study was to determine the effects of plant species, type of irrigation, type of fertilizers, and use of dust control chemicals on plant growth and surface coverage. Best grass coverage, nearly 100 percent with 240 plants per square foot, was developed in a section that was seeded with crested wheatgrass, fertilized with sewage sludge, and sprinkler irrigated. For comparison, a section that had been treated with commercial fertilizers developed 3.1 crested wheatgrass plants per square foot and 24 percent coverage without irrigation, and 8 plants per square foot and 75 percent coverage with irrigation. Results of spraying a dust control chemical were inconclusive. Russian-thistle invaded all test sections and ranged in density from 0.6 to 7.3 plants per square foot.

Jan 1, 1982

By T. A. Johnson

Recovering from low demand in 1975, raw mineral production in the United States maintained a steady climb in value and quantity throughout 1976, keeping pace with the gross national product (GNP), which increased 11.5% compared with that of 1975. The minerals industry, in the past, has met ever-increasing demand while keeping production costs to a minimum. To maintain this capability, technological research and development of more efficient processing methods must continue. The role of Government and its increasing involvement in minerals industry actions received unfavorable comment from various segments of the industry in 1976. Government pricing controls were of concern to most industrial firms marketing like products. Public land withdrawals in large blocks were of concern to the mineral industry.

Jan 1, 1978

Heavy liquids have come into use in ore-dressing investigations, as they make possible the separation of an ore into its specific-gravity components. A paper containing a general dissertation on heavy liquids has been written by John D. Sullivan,4 and the practical application of heavy liquids is explained by Box and Crabtree5. Some heavy liquids become discolored after continued use, and the lack of transparency impairs their value. Since they are fairly expensive, reclaiming is desirable. This paper briefly discusses the preparation and care of some of the more common heavy liquids.

Jan 1, 1928

By D. D. Dornenburg

The effect of changes of atmospheric pressure on methane emissions from extensive worked-out areas of coal mines in several Midwestern States has lone caused concern to State and Federal mining departments, as well as to the operating companies involved. Common mining and ventilation methods employed in mines in these States have resulted in large sealed and unsealed worked-out areas in which considerable quantities of methane are emitted alone both intake-and return-air courses. The common practice is to watch barometric changes very closely and take special precautionary measurer during periods of low barometric pressure. Although the hazard is recognized, mining officials have different opinions concerning the effect of barometric pressure variations on the emission of mine gases. These opinions are based upon scattered personal observations, as no records exist of actual studies to establish such effects.

Jan 1, 1955

By Jerry W. Stengel

The Bureau of Mines subjected two manufacturers' chemical oxygen (K02) self-rescue breathing apparatus to a series of laboratory environmental treatments designed to simulate various conditions in underground coal mines. The environmental treatments consisted of extremes of temperature, shock, and vibration. The tests were designed to be used as predictors of the ability of the self-rescuers to survive those environmental insults with no degradation in their protection to the wearer. Based on the severity of the treatments, simulating conditions more severe than offered by the mining environment, the two apparatus tested should be able to withstand the abuse offered by the mining environment and still function as intended in an emergency. Correlation of these tests with results of long-term field evaluations is needed to provide confidence in the laboratory tests as predictors.

Jan 1, 1982

By W. Bruce Montgomery

Manganese oxides occur, with some iron oxides, in small scattered lenses on property controlled by the Columbia Manganese Co. (1943) near Evington, Campbell County, Va. The company mined some manganese ore during 1917 and 1918. A preliminary examination in May 1942 indicated the possibility of finding additional ore. On August 21, 1942, the Bureau of Mines began prospecting to verify the continuity of the ore exposures. Work on this project continued until February 5, 1943. Prospecting and development work included shaft sinking, crosscutting, drifting, trenching, and test-pitting in six separate areas indicating two types of deposits. The most predominant type is a wide brecciated area in which occur lenses or pockets of nodular manganese oxides. The other type is characterized by more of a vein structure, including thin layers of manganese oxides.

Jan 1, 1949

By D. J. Bauer

Solvent extraction techniques were used to determine the extraction sequence of yttrium and the rare-earth elements in an amine solvent extraction system. Single-stage extraction with Primene 81-R resulted in separation factors of 3.8 between yttrium and dysprosium and 25 between yttrium and cerium. Yttrium was concentrated in the aqueous phase. EDTA and DTPA, as aqueous phase counterextractants, enhance separation factors in mine-rare-earth sulfate systems. Yttrium separation from heavy rare-earth elements exhibits marked sensitivity to the position of yttrium in the selectivity scale of the rare-earth elements with the sequestrants. Yttrium-ytterbium separation is more effective with EDTA, whereas yttrium-dysprosium separation is more effectively increased with DTPA.

Jan 1, 1963

By Richard H. Spencer, Warren G. Bender

Since the passage of the Coal Mine Health and Safety Act of 1969, the Bureau of Mines has made many advances in mine communications. These efforts have resulted in the following developments and demonstrations: • Surface-to-surface electromagnetic transmission of baseband voice signals through overburdens as deep as 600 feet. This transmission was achieved with equipment from the Interim Mine Rescue and Survival System Program, and demonstrated that baseband voice communications could be obtained through these overburdens in the absence of mine-generated noise; that is, when the mine power system was shut off. However, during mine operational conditions, the mine-generated noise proved to be so large that effective baseband voice communications to the desired depths could not be effected. • The development of beacon transmitters for locating trapped miners. This work was again the outgrowth of the Interim Mine Rescue and Survival System. Extensions of this work have led to reliable detection and location of trapped miners to depths of 1000 feet. The system, which makes use of a loop antenna deployed where the trapped miner is located, uses low-duty-cycle, tone-burst transmission. Portable tuned receivers and loop antennas are used on the surface to determine the location of the trapped miner. An extension of this work has led to a call-alert paging system concept, wherein a transmitter, similar to that used in the trapped miner system, is used to audibly and/or visually alert key mine personnel carrying pocket receivers that they are wanted at the nearest mine telephone. In addition, a roof-bolt paging system has been developed, wherein commercial paging and mine carrier phone equipment are used in conjunction with a long-wire "roof bolt" antenna to page individuals and relay to them short voice messages.

Jan 7, 1975

By Joseph S. Coffman

The Bureau of Mines investigated the availability of barite (BaSO4) from 35 U.S. and 41 non-U.S. mines and deposits in 17 market economy countries (MEC's). This evaluation assesses the availability of mud-grade barite, and concentrates consumed by the chemicals and fillers industries. The demonstrated resources defined in this analysis totaled 130 million metric tons (Mmt) of barite (contained BaSO4), yielding a potential 115 Mmt of recoverable barite concentrates. At the 1984 MEC production rate, the evaluated resources would last about 30 yr; however, this would include production costs of up to $100/mt concentrate. An average price needed to cover all costs of production over the life of each operation was determined for both mud-grade and chemical- and filler-grade barite products. Including a 0-pct discounted-cash-flow rate of return (DCFROR), regional weighted- average total production cost ranged from $38/mt for barite concentrates in Asia to $71/mt for U.S. operations. Transportation costs have the greatest impact, contributing up to 60 pct of the total cost of production. Rail transportation costs from the mines to U.S. markets are generally significantly higher than ocean shipping rates on imports.

Jan 1, 1986

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

8. Field Demonstration of the Remote Mine Sealing System in a Coal Mine 8. 1 Selection of Field Test Site Eastern Associated Coal Corporation (EACC) offered its Federal No. 1 coal mine in Grant Town, West Virginia as the site for field testing of the remote sealing system. The choice of Federal No. 1 mine was particularly appropriate as the first attempt at fire control by remote sealing was done in this mine in 1963. EACC provided the men and equipment required for much of the initial preparation. Considerable assistance, advice, and background on coal mining technology was given by Mr. William Laird, Vice President for Research and Development, EACC, and by Mr. Lawrence Jackson, Resident Engineer at the Federal No. 1 mine. District 3 USBM office, the West Virginia Bureau of Mines, the Technical Support Group of the USBM, and Local 4047 of the United Mine Workers of America also cooperated. 8.2 Preparation of Field Test Site 8.2. 1 Underground Site Preparation The underground site chosen for the field testing was in a non-working portion of the mine within a few hundred feet of the main haulage road, as shown in Figure 80. Known as "Seven Switch, " this area was a 20 minute walk or 5 minute "jeep" trip from the man-trip shaft. Ten years having passed since this area was actively worked, considerable effort was required for gob clearing, roof bolting, rock dusting, and rejuvenating the track from the haulage road to the test area. Three primary borehole locations were chosen for the test program. Borehole No. 1 was in a straight passageway

Jan 1, 1973

By Paul Hopkins

The following methods have been selected from a large number tried while assaying several hundred samples of placer concentrates. It is thought that some of these methods may be useful to those who are required to assay similar products containing large quantities of metallic articles, such as jeweler's sweepings. No great difficulties will be encountered in assaying black sand from beaches or river bars. Such samples require care in grinding and sifting so that no oversize particles of sold or platinum are lost. It is also necessary to have sufficient silica in the flux to form a fluid slag with the excess of iron, magnesium, or chromium Which such samples contain.

Jan 1, 1934

By M. D. Schlesinger

Experimental data for coal hydrogenation are presented to show that when a vehicle oil produced from coal is present, coal is hydrogenated to the same high conversion whether molybdenum catalyst is impregnated on the coal or intimately mixed with the slurry. Differences in product distribution could be related to the severity of operating conditions. No minimum mixing time was established, but 2 hours was sufficient. Longer periods of mixing, to 14.75 hours, had no effect on the results. The hydrogenation conditions were in the pressure range of 8,500 to 10,000 p,s,i. at 400° to 500° C. Most of the experiments were made in duplicate. The results were obtained with molybdenum concentrations of 0.01, 0.1, and 1 percent. Al the mentioned pressure range and a time at temperature of 15 to 60 minutes, coal conversions higher than 98 percent were obtained.

Jan 1, 1962

By Paul Hopkins

The following methods have been selected from a large number tried while assaying several hundred samples of placer concentrates. It is thought that some of these methods may be useful to those who are required to assay similar products containing large quantities of metallic articles, such as jeweler's sweepings. No great difficulties will be encountered in assaying black sand from beaches or river bars. Such samples require care in grinding and sifting so that no oversize particles of gold or platinum are lost. It is also necessary to have sufficient silica in the flux to form a fluid slag with the excess of iron, magnesium, or chromium which such samples contain. It is much more difficult to assay black sands, or concentrates, produced in large-scale placer-mining operations. These products are usually much harder and more abrasive than the beach black sands. They also contain numerous metallic particles resulting mainly from wear on the mining machinery. These particles consist chiefly of iron or steel but also contain lead, copper, and alloys such as babbitt, solder, brass, ferrosilicon, etc. Fairly large particles of gold are often found. Some samples will contain as much as 10 percent of such metallic particles. It is not feasible to remove the particles of iron with a magnet and discard them, as they invariably contain gold, sometimes a considerable amount. This gold is attached to the iron particles by rust or wedged into cavities. Scraps of sheet iron are often found which have become tightly folded or rolled and contain gold or amalgam within the folds.

Jan 1, 1934

By B. E. Blair

Accelerometers of various types, velocity gages, and a displacement meter are shown to give reliable date when measuring seismic pulses generated in rock by the detonation of explosive charges. Displacement and velocity records are differentiated and shown to compare with velocity and acceleration records. Velocity and acceleration records are integrated and shown to compare with displacement and velocity records, respectively. The experimental data are shown to satisfy the scaling laws developed by dimensional analysis. Propagation laws are developed for peak amplitudes of the first pulse of displacement, velocity, and acceleration. These propagation laws are shown to be independent of the gage used to obtain the data. As a result, the usefulness of the various gage types can be extended. For example, accelerometers, because of their high frequency and amplitude limits, can be employed near the shot to measure acceleration and/or velocity (by integration), Velocity gages, because of their higher sensitivity, can be employed at relatively larger distances from the shot to measure velocity and displacement or acceleration (by integration or differentiation).

Jan 1, 1954

By Stephen Utter

This report summarizes the procedure and results of an investigation to determine the stresses in the rock around an underground opening in the Climax molybdenum mine, Climax, Colo. This study is part of an overall investigation conducted by the Bureau of Mines to determine the stresses induced by block-caving mining. The purpose of this study is to obtain estimates of the magnitudes and directions of the principal stresses, the location of the maximum stress concentrations, and the effect of topography on the stresses.

Jan 1, 1962

By James C. Barker

Gold placer deposits along the upper Yukon River, in the region between the river villages of Circle and Eagle, were investigated by the Bureau of Mines. The investigation was conducted intermittently between 1976 and 1985 as part of an evaluation of mineral resources on lands proposed for inclusion in the National Park System. At least 230,000 troy ounces (tr oz) of gold has been produced in the region, principally from Woodchopper, Goal, and Fourth of July Greeks. The placers are underlain by, or occur downstream of, early Tertiary sediments that have been deposited in the Eagle Trough. Strike-slip displacement along the Tintina Fault is responsible for creation of the trough and may have been a factor in the formation of the present placers. Placers were found to have a close spatial correlation to certain altered fault lineaments of the Tintina Fault trench. Placer concentrates contain several different textural forms of gold, suggesting multiple origins. Geological studies and a survey of 162 panned concentrates throughout the region indicated previously unreported sites of placer gold, and potential exists for the discovery of additional placer and lode gold. Because of nearly continuous soil and vegetation cover, further evaluation of the region will require subsurface sampling.

Jan 1, 1986