Search Documents

By Dennis J. Grigal

The objective of this contract was to monitor operating conditions of, four flooded, fibrous-bed filter panels used during normal underground mining operation and to analyse clogging and structural problems. After observing structural and clogging problems and conducting laboratory and field tests, a final, Flooded, fibrous-bed filter design which minimizes clogging and structural problems was recommended to the Bureau of Mines. This report also describes the dust sampling procedures used to determine the dust concentration at the flooded, fibrous-bed scrubber intake duct.

Jan 1, 1979

By C. Ortuglio

The effect of cracking by increasing the free space above the charge on the composition and yields of the volatile products from carbonization of Pittsburgh-bed coal and one industrially used blend from Eastern United States and one from Western United States was investigated with the BM-AGA carbonization apparatus. Increasing the free space above the charge from 1 inch to 3 inches, to 6 inches, and to 9 inches resulted in lower tar yields and increased gas and light oil yields. Anthracene and naphthalene yields were increased; quinoline and benzene insoluble fractions of both the tar and pitch increased considerably with increased free space, although the carbon content of the tars and pitches increased only slightly. Increased cracking, occasioned by the increase in free space, resulted in a decrease in the yields of tar acids, tar bases, neutral oils, olefins, aromatics, and paraffins and naphthenes. Gas composition was relatively constant; hydrogen and methane tended to increase and ethane decrease. Results of the investigation are being used to design a unit to upgrade the volatile products of carbonization by cracking the hot products as they leave the carbonization chamber.

Jan 1, 1970

By W. L. Dare

This publication is one of a series by the Federal Bureau of Minus describing methods and costs of minim, uranium on the Colorado Plateau. The La Sal mine is in the Big Indian mining district, about 29 miles southeast of Moab, San Juan County, Utah. The claims that encompass the mine were located in March 1953, and the La Sal ore body was discovered as a result of a drilling program begun in August 1953. The mine is owned by the La Sal Mining & Development Co., a subsidiary of the Homestake Mining Co. Homestake continued the drilling program and in May 1954 began sinking a 572-foot shaft and constructing a surface plant. The plant and shaft were completed in October 1954. The La Sal ore body is in the Chinle (Triassic) formation. it is tabular and dips with the enclosing beds about 8° southwest. The ore body is generally 4 to 8 feet thick but in a few places is as much as 20 feet thick it is being developed by a series of strike drifts and dip inclines, driven within the ore stratum on about 100-foot centers. A haulage level driven beneath the ore body is connected by raises to the upper workings.

Jan 1, 1957

By W. H. Hamilton

The Kokomo (Tenmile) mining district has had an output valued between $20 and $30 million, mostly from production of silver, lead, and zinc, since 1878. For many years before World War II, there was little production, as the complex nature of the ores made them unattractive at existing metal prices. Under the stimulus of the war, the Geological Survey and the Bureau of Mines studied they district, and in October 1944 the Bureau of Mines began an exploration project, which included dia¬mond drilling, bulldozer trenching, and geophysical surveying. Project work was continued until March 1949, except for short recesses during 1945, 1947, and 1948. Forty-five diamond-drill holes, totaling about 13,000 feet, were drilled from underground and surface stations on the various properties in the district. Eleven bulldozer trenches, abut 2,400 linear feet, were excavated in an attempt to uncover the outcrop of the middle Quail limestone. These trenches ranged from 100 to 485 feet in length and reached a maximum depth of 15 feet. A limited geophysical investigation was made during the summer of 1946. The length of the traverses were: Magnetic, 990 feet; resistivity, 6,250 feet; and self-potential, 69,780 feet.

Jan 1, 1955

By Jack L. Woodward

The evolution of surface mining equipment has resulted in larger, faster haulage units, loaders, etc., resulting in increased demands on steering technology. Careful analysis of these systems was warranted to determine if steering-related safety problems have been introduced. The objectives of this program were to: 1. Define the generic types of steering systems being used on mobile mining equipment used in surface mining operations. 2. Gather information on steering-related accidents in mining operations. 3. Assess the need for initiating government-sponsored research into steering system technology. A comprehensive literature survey was conducted concurrent with extensive contacts with mining operations, mining equipment manufacturers, steering system component manufacturers, and government agencies. A Technical Evaluation Group composed of representatives from the above organizations was formed to review the data gathered. It was concluded that the steering systems in use on surface mining equipment are reliable and do not present a safety problem. The Society of Automotive Engineers, Inc. is active in pre-paring voluntary consensus standards to assure that the minimum levels of performance are defined for industry.

Jan 1, 1979

By Almon F. Robertson

"INTRODUCTION AND SUMMARYThis is one of a series of reports describing investigations within the Missouri River Basin in Montana conducted by mining engineers of the Bureau of Mines, Minerals Division, Region II. The primary purpose of these investigations is to provide basic information to agencies of the Department of Interior and others concerned with the planning of power and other water developments in the basin. This report contains only such factual data as have been authorized for public distribution. Special precautions have been taken not to reveal any information or data that are considered confidential.The field investigations for this report were made during the summer of 1949. Virtually all known metallic mineral deposits in the county and same nonmetallic (industrial) mineral deposits were investigated. Most of the mines and prospects have been inactive for many years. The old underground workings generally are only partly accessible; many are entirely inaccessible. Most of the mining claims were located many years ago, and a considerable number were patented. Many claims were abandoned; others were relocated. Nimes and ownerships often have changed. Because of such conditions, much of the information on most of the mines and prospects necessarily has been obtained from available Federal and State publications, private geologists' and engineers' reports, and from owners and local residents.Metal mining in Cascade County, Mont., has been confined mainly to the silver-lead-zinc deposits in the Montana (Neihart) and Barker districts in the southeastern part of the county. The Neihart district has yielded by far the greater part of the county's metal output. The mines generally have been operated intermittently, largely because of fluctuating or low silver and base metal prices."

Feb 1, 1951

By Richard J. Leary

The inputs of capital and labor to support future iron ore production were developed by the Bureau of Mines from projections of iron demand and estimates of capital and labor requirements. Trends in technologic change and the organization of production were analyzed. Labor requirement schedules for iron ore mining and beneficiating were constructed from aggregate inter-temporal trends and 1970 cross-sectional analysis of mines and mills. A sup-ply schedule of the capital requirement for mine-mill-pellet plants was developed from U.S. and Canadian experience. The structure of demand for iron to the year 2000 was examined as well as the availability of resources. Projections of capital and labor requirements to 2000 were constructed under two international patterns of iron ore supply to the United States. The most likely model is for a continuation of the 70 percent United States-30 percent foreign shares, expanding at an average 2.0 percent growth rate to 2000, and supported by a cumulative gross capital investment of $3.8 billion constant 1967 dollars and a labor force in the United States of 29,800 by 2000. The information content of projections is discussed, and the possible effects of international forces on supply are considered. A generalized methodology for estimating capital and labor requirements in other mineral industries also is included.

Jan 1, 1975

By S. R. Borrowman

Mill tailings from conventional uranium extraction processes contain nearly all of the radium originally in the ore. Such tailings require controlled storage in perpetuity to safeguard the surrounding environment from radioactive contamination. Alternatives to controlled storage of the tailings are (1) removal of the radium from the tailings for separate storage or use or (2) removal of the radium when processing the uranium ore. In laboratory tests conducted by the Federal Bureau of Mines, radium was leached from tailings using either hydrochloric acid or ethylenediamine tetraacetic acid. A hydrochloric acid leaching method was used to extract both radium and uranium from the ore to yield tailings containing less radium than those produced by either conventional sulfuric acid or alkaline leaching processes. From 77 to 94 percent of the radium in mill tailings was concentrated by sedimentation in slime fractions representing nearly 25 weight-percent of the original sample.

Jan 1, 1975

By Carroll W. DeKock

Thermodynamic data for selected metal sulfates were critically evaluated and compiled as part of the Bureau of Mines program to provide a scientific base for use in developing new technology and predicting the feasibility of new processes. Values for Cp°, S°, H° - H°298, - (G° - H°298)/T, ?RC, ?Gf°, and log Kf as functions of temperature are given in tabular form. Thermodynamic data were compiled for Ag2SO4, A12(504)3, A12(S04)3?6H20, BaSO4, BeSO4, BeSO4?2H2O, BeSO4?4H20, CaSO4, CaSO4?1/2H20, CaSO4?2H2O, CdSO4, CdSO4?H20, CdS04?8/3H20, 2CdO?CdSO4, Cs2SO4, In2(S04)3, K2504, KA1(S04)2, KA1(S04)2?12H20, Li2SO4, L12SO4?H20, MgSO4, MgSO4?H2O, MgSO4?2H20, MgS04?4H20, MgS04?6H2O, MgS04?7H2O, Na2SO4, Na2S04?7H20, Na2SO4?10H20, (NH4)2SO4, NH4A1(S04)2, NH4A1(S04)2?12H20, PbSO4, Rb2SO4, T12SO4, and Zr(S04)2.

Jan 1, 1986

By H. Polat, Q. Hu, M. Polat, S. Chander

"The electrostatic charge on spray droplets of ionic surfactant solutions and coal particles was measured and the results were correlated with the dust collection efficiency. When various surfactant were added, the magnitude of the droplet charge increased significantly and it was observed to be a function of surfactant type and concentration. The concentration of maximum droplet charge coincided with surfactant concentration where maximum collection efficiency was observed for these surfactants. Particles of coal also carried substantial amount of charge magnitude of which seemed to be a function of coal rank.Based on the results presented in this paper, it was concluded that ionic surfactant primarily act as a strong electrostatic charge inducer for droplets. Due to interactions between these highly charged droplets and naturally charged particles, the efficiency of droplet-particle collisions play a primary role when compared to the wetting and engulfment phenomenon which could only follow a successful collision. INTRODUCTIONWater spray are widely used to suppress airborne dust in mine atmospheres (Walton and Woolcock, 1960; Kobrick, 1970; Hamilton, 1974; Jayaraman et al., 1986). Several investigators have considered the use of surfactants to enhance the effectiveness of water sprays especially for difficult to wet particles such as those of coal (Glanville and Wightman, 1979). The capture of dust particles by water droplets involves droplet-particle collisions, adhesion of particles to droplets, and engulfment of particles into droplets. Surfactants affect these sub processes through their influence on droplet charge, surface tension, and wetting. The last two mechanism have been thoroughly studied in recent years (Walker et al., 1952; Cohen and Rosen, 1981; Glenville and Haley, 1982; Chander et al., 1988; 1991). However, little attention has been paid to the role of electrical charge on particles and droplets on the collision and adhesion of spray droplets and dust particles."

Nov 1, 1995

By F. E. Cash

The Holmes Safety Association , organized and named in honor of the late Dr. Joseph A. Holmes , first director of the United States Bureau of Mines , has for its object the prevention cf accidents , the improvement of health conditions at work, in the home , and in public places , and the promotion of the general welfare of its members . As a means of preventing accidents and advancing health and safety , the Holmes Safety Association disseminates information , gives instructions on subjects related to safety , and promotes first -aid and other forms of protective and accident - prevention training . This organization is intended to work and cooperate in the closest possible way with existing mine or plant safety organizations in conducting educational , social , and recreational activities for the promotion of health , safety , and efficiency .

Jan 1, 1929

By A. F. Cohen

When location guidelines are followed in choosing sites for fixed point velocity transducers for use in underground coal mine monitoring, mine air turbulence intensities <11% are generally expected at those sites. The objective of this Bureau of Mines investigation to determine the effect of turbulence intensities <11% on vortex shedding sensors and transducers. Measurements were made at velocity levels of interest for underground coal mine monitoring use (?200, ?500, ?1,000, ?1,500 ft/min). The effect of grid-produced turbulence intensities (2% to ?14%) on the output of vortex-shedding air-velocity transducers was less than ±10%.

Jan 1, 1985

By Mark Sheppard

This paper is the third of a series recording the results of tests made at various quarries throughout the United States to determine (1) the relation between the size gradation of feed to, and product from, primary crushers, (2) the particle shape of the crushed. product, (3) the differences in gradation and particle shape produced by different types of primary crushers, and (4) the differences in gradation and particle shape caused by crushing different kinds of stone. Progress reports 1 and 2 dealt with comparisons of different types of crushers crushing the same type of stone. This report deals with relation¬ship between feed and product of two different limestones, as to size distribution and particle shape, when crashed in the same crusher.

Jan 1, 1938

By W. W. Adams

"Accidents at coal mines in the United States in September 1926 resulted in the loss of 170 lives, according to information furnished to the Bureau of Mines, Department of Commerce, by State mine inspectors. Of this number 125 occurred at bituminous mines and 45 in the anthracite field. As the bituminous output of coal for September was 48,976,000 tons, and the production of anthracite was 8,444,000 tons, the fatalities reported represented a death rate of 2.55 per million tons for bituminous mines and 5.33 for anthracite mines. The industry as a whole showed a fatality rate of 2.6 per million tons of coal produced in September 1925 the rate for bituminous coal mines was 3.29; the anthracite mines were idle in September last year due to a strike.During the first nine months of the present year 1,759 men have been killed by accidents at the coal mines throughout the United States, resulting in a death rate, per million tons of coal produced, of 3.76 as compared with 3.95 for the same period in 1925. Reports for bituminous mines alone showed a nine-month fatality rate of 3.53 which was about the same as the corresponding rate from January to September in 1925. The anthracite rate for the present year, however, shows a decrease of about 17 per cent; that is, the rate has declined from 6.36 to 5.28.Records covering the first nine months of 1926 show that 12 ""major"" disasters, that is, disasters in which five or more men were killed at one time, have resulted in the loss of 271 lives as against 10 disasters and 199 deaths in the corresponding months in 1925. The fatality rates for these disaster: alone were 0.579 and 0.465, respectively. One major explosion occurred at Tahona, Oklahoma, on September 3, 1926, in which 16 men lost their lives.An analysis of the principal causes of the 1,759 fatalities for the first nine months of the present year shows a reduction in the death rate as a whole and for falls of roof and coal and for explosives, but an increase in haulage, gas and dust explosions, and electricity. The comparative rates for these accidents were:"

Oct 1, 1926

By R. V. Ramani

This volume is the third of a four-volume final report on research carried out under a contract from the U.S. Bureau of Mines on the development of a computer simulation model for surface mine reclamation planning. The other volumes are titled as follows: Volume I: Ore Reserve Estimation, Volume II: Dragline Model, and Volume IV: User&apos;s Manual for OPMHS/2. The Mine Coordinate Generator System serves as an interface between the Geology and Reserves System (Volume I, final report) and OPMHS/2 (Volume IV, final report) to provide local mine grid information which is used as input to the decision making process and dynamic simulation routines of OPMHS/2. After the Geology and Reserves System has been successfully run for a property, a data base containing values for each grid cell covering the property is created at the end of execution, if chosen as an option by the user. The Mine Coordinate Generator reads this information and creates a special direct access data set from the sequential data input. When information defining the mine grid is read, the values present in the property grid are for the interpolation of values for each mine block.

Jan 1, 1985

By M. C. Irani

The Bureau of Mines, in cooperation with the Mine Safety Appliances Co., has developed a new methane analyzer system for underground applications. Methane enters coal mine ventilation air from the breakup of coal at the active face, from the collapse of roof rock during retreat mining, and from the ribs abutting virgin coal. Each source contributes varying amounts to the total emission, depending upon rate of mining, type of mining, and the character of the coalbed and adjacent strata. The evaluation of individual parameters of methane emission requires the continuous monitoring of individual mine sections over a long period of time. The methane analyzer system was developed to meet this need. The system has been installed and operated in an active mine in the Pittsburgh coalbed. The system and details of its installation and calibration are described. Data are presented to substantiate its reliability.

Jan 1, 1975

By P. C. Good

High-purity chromium was prepared in massive form by the electrolysis of chromium trioxide solution at high temperatures. The metal thus obtained, containing 50 to 150 p.p.m. of oxygen, 20 p.p.m. of nitrogen, and traces of metallic impurities, could be hot-worked to rod and sheet and drawn to wire ductile at room temperatures. Optimum concentrations and operating conditions were established for the deposition of chromium from chromic acid baths containing sulfate, fluoride, and silicofluoride ions. Current efficiencies of 13 percent were attained with baths containing sulfate ion, and efficiencies of 40 to 44 percent with baths containing fluoride and silicofluoride ions. Cation exchange resins were used for removing metallic impurities from chromic acid solutions containing sulfate ion; solutions containing fluoride and silicofluoride ions were purified by recrystallization.

Jan 1, 1960

By Mark Sheppard

This paper is the third of a series recording the results of tests made at various quarries throughout the United States to determine (1) the relation between the size gradation of feed to, and product from, primary crushers, (2) the particle shape of the crushed product, (3) the differences in gradation and particle shape produce- by different types of primary crushers, and (4) the differences in gradation and particle shape caused by crushing different kinds of stone. Progress reports 1 and 2 dealt with comparisons of different types of crushers crushing the seine tyre of stone. This report deals with relationship between feed and product of two different limestones, as to size distribution and particle shape, when crashed in the same crusher.

Jan 1, 1938

By E. C. Lane

This paper on the physical and chemical properties of crude oils from California fields is one of a series of reports on the oil-producing districts of the United States. The paper includes a short discussion of results, tabular data, and individual analyses of 16 California crude oils. Analyses of other oil from California have been published in Reports of Investigations 25954/, 26085/, 28466/, and 30747/. The samples were obtained by members of the San Francisco office of the Bureau of Mines. The collecting of the samples vas facilitated by the courtesy of representatives of oil companies in California.

Jan 1, 1937

By E. C. Lane

This paper on the physical and chemical properties of crude oils from California fields is one of a series of reports on the oil-producing districts of the United States. The paper includes a short discussion of results, tabular data, and individual analyses of 16 California crude oils. Analyses of other oil from California have been published in Reports of Investigations 25954/, 26085/ 28466/, and 30747/. The samples were obtained by members of the San Francisco office of the Bureau of Mines. The collecting of the samples vas facilitated by the courtesy of representatives of oil companies in California.

Jan 1, 1937