Search Documents

By J. P. Powell

Since the beginning of waterflooding in the Midcontinent area, the Bureau of Mines has published many reports3-6/ describing in detail the results obtained on individual waterflooding projects in the area. These are intended as guides for operators in the selection of well-spacing, water-treating, and other techniques, as well as an indication of the results being obtained in waterflooding in various areas, fields, and horizons. In addition, Bureau personnel has arranged a tour of selected waterflooding projects each year for the past several years so that actual operating conditions may be observed and an additional opportunity provided for exchanging information. Each of these tours has been supplemented by a published

Jan 1, 1959

By George A. Morgan

The 53 countries that constituted Africa in 1991 accounted for a significant portion of total world output of a number of mineral commodities. However, total output for the continent declined for many major mineral commodities produced compared with that of 1990. Also, Africa's share of total world output of these commodities generally declined. (See tables 1 and 2.) The most conspicuous declines were for cobalt and copper owing to mining and metal processing difficulties experienced by the world's two largest cobalt producers, Zaire and Zambia. Phosphate rock output declined primarily owing to a sharp fall in production from Morocco, also a leading world producer. Morocco's state corporation for phosphate production experienced marketing problems, leading to the decline.

Jan 1, 1993

By V. E. Homme, M. M. Wong

Tests were made in reactors ranging from 12 to 30 inches in diameter to develop methods for the preparation of sodium chloride - titanium lower chlorides ( dichloride and trichloride ) melts that contain titanium predominantly in the divalent state . Such melts are desirable as a starting material for the production of titanium metal or as an electrolyte for electrorefining of titanium . Sodium reduction of TiCl with an 18 - hour period of holding the reaction products in the molten state produced melts that contained titanium lower chlorides in TiCl₂ - to - TiCl , molar ratio of approximately 8 to 1. Sodium reduction of TiCl in a reactor with a shielded pipe weir , that required no melt -holding period , produced melts with a TiCl₂ - toTiCl , molar ratio as low as 4 to 1 . Reduction of TiCl4 with scrap titanium metal in molten sodium chloride produced relatively pure melts containing about 27 percent titanium in a Ticl₂ - to - Ticl , molar ratio of approximately 4 to 1 .

Jan 1, 1964

To improve the ventilation of large-opening under-ground stone mines by using stoppings made from stone left in place. Background Underground stone mines typically use large room-and-pillar openings with little ventilation control. Stone miners may be exposed to contaminants that include silica dust, diesel particulate matter (DPM), exhaust gases, nuisance dust, and face shot (blasting) fume gases. The health risks from breathing these fine particles and toxic organic materials are well documented. Although contaminants such as dust or diesel exhaust can be some-what controlled at the source, the escaping contaminants are often diluted and removed from work areas using ventilation with minimal controls. In many cases, current mine ventilation practices use trial-and-error techniques to improve ventilation. The growing realization of the importance of a healthy work environment along with increased regulations will require many stone mines to implement new ways to improve ventilation. In-place stone stoppings are one option. Mine air flows from one point to another because of a pressure differential between those points. This pressure differential is established using a mechanical fan in conjunction with separations (stoppings) between high-pressure (intake) and low-pressure (return) airways. The separation of intakes and returns is an important concept that is used in most other types of mines. Normally, air moves through underground stone mines with minimal control technology. Fans are placed in locations where they are thought to be most beneficial, and intakes are not separated from returns. In a few smaller underground stone mines, proper ventilation can be achieved with a few strategically placed fans. However, as these mines increase in size, moving adequate quantities of air through-out the mine becomes harder, and separation of intakes and returns becomes a problem. Building traditional mine stoppings to separate the intake and return airways in entries with a cross-section area often exceeding 800 ft2 is difficult. The stoppings must be able to withstand both the dynamic pressure from face shots and the static pressures created by the fans. Construction and maintenance difficulties, as well as high costs, are the main factors preventing these traditional mine stoppings from gaining wide acceptance by the stone mining industry.

Dec 1, 2002

By David C. Byrne

PURPOSE: Evaluate practical technological advances in hearing protective devices for use in different mining environments. RESEARCH SUMMARY: Previous NIOSH research shows that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals and that miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and sex. As described in the National Occupation-al Research Agenda, problems created by occupational hearing loss include(1) reduced quality of life due to social isolation and unrelenting tinnitus,(2) impaired communication with family members, the public, and coworkers, (3) diminished ability to monitor the work environment (i.e., warning signals, equipment sounds, etc.), (4) lost productivity and increased accidents resulting from impaired communication and isolation, and (5) expenses for workers’ compensation and hearing aids. Although eliminating hazardous noise is the long-term solution to the noise problem, miners will likely need to rely on personal hearing protection in certain situations for quite some time. However, it is well known that noise attenuation provided by hearing protectors as they are worn during everyday use is usually quite different (i.e., worse) than when tested under lab conditions. In addition, workers may refuse to wear their hearing protection for any number of reasons. This project was initiated to evaluate practical technological advances in hearing protectors, with an emphasis on optimizing the balance between effectiveness, comfort, over protection, and communication ability. The recently completed auditory research facility is now under-going the accreditation process conducted by the National Institute of Standards and Technology under the National Voluntary Laboratory Accreditation Program. Experiments are planned to investigate the factors that affect a miner’s ability to hear hazard and warning sounds (e.g., roof working, alarm signals, spoken communications, etc.). A service contract has been initiated to record and digitally store samples of typical warning sounds heard in an underground coal mine. This information will be analyzed in the lab to develop recommendations that can be offered to the mining community regarding correct earplug/earmuff usage to maximize there cognition of hazard and warning sounds while adequately protecting the miners’ hearing.

Jan 12, 2001

By T. J. Ballard

Chromite deposits in the vicinity of Louise, Troup County, Ga., were studied y the Bureau of Mines from September 1, 1942, to March, 15, 1943. They are about three-fourths of a mile southeast of Louise and 8 miles northeast of La Grange, Troup County, Ga. The existence of chromite deposits in that area has been known for more than 75 years, but no active prospecting was done until World War I. Prospecting continued intermittently' until 1928. The Bureau became interested in the deposits in connection with its strategic minerals investigations during World War II. The chromite in these deposits occurs as grains ranging from "pin-head" size to 3/8-inch and occasionally 1 inch. Some of the material is magnetic, indicating the presence of magnetite. Of the 300 samples taken during the course of the project, 266 were analyzed. Tables showing the analyses accompany this report.

Jan 1, 1948

By M. O. Serbousek

The load-transfer mechanics of fully grouted roof bolts in coal mines have been investigated in laboratory and analytical studies. The purpose of this Bureau of Mines research is to increase understanding and better interpret data from routine field pull tests and to develop a numerical model of a grouted bolt that can be used in a global computer model of a mine roof. Analytical studies using closed-form solutions and finite-element techniques were compared to experimental results. Laboratory work includes variation of bolt length, hole diameter, and grouL type. Pull tests were pel'fol·med on 4-, 2-, and I-ft bolts in holes of 1-and I-3IB-in diameters. Both polyester resin and inorganic grouts were used as the anchorage medium. Strain gauges were installed on the bolts at several locations to observe the rate of load transfer from the bolt through the grout to the rock mass when a force was applied at the bolt end using standard jack pull testing procedures and equipment. The average anchorage length of 4-and 2-ft bolts was 22 in. Grout type and hole size variations did not produce a significant effect on the rate of load transfer from the bolt to the rock.

Jan 1, 1987

By Douglas D. Reynolds

Intense vibration can be transmitted to the hands and arms of workers who use hand-held percussive or vibrating devices, tools, and work pieces. Continued habitual exposure to vibration directed to the hands can cause patterns of various symptoms associated with hand-arm vibration syndrome (HVAS). The International Organization for Standardization (ISO) first published ISO 5349 in 1986.3 This standard specified methods for measuring and evaluating vibration directed into the hands from hand-held vibrating devices, tools, and work pieces. The American National Standards Institute (ANSI) published ANSI S3.34 the same year.1 This standard was modeled after ISO 5349-1986 and specified methods for assessing exposure to hand-arm vibration. The Parliament of the European Union has issued the European Union Human Vibration Directive-2002/44/EC, which specifies vibration daily exposure action values (DEAV) of 2.5 m/s2 and daily exposure limit values (DELV) of 5.0 m/s2. These values have generally been accepted by medical experts, scientists, and engineers in governmental agencies, research institutions, and industry in the USA and other countries.2 When they are achieved, they will reduce the potential for the development of symptoms related to HAVS among workers exposed to hand-arm vibration. Significant improvements in measurement and analysis instrumentation, miniature and subminiature accelerometers, and medical diagnostic and assessment protocols have being introduced since 1986 when ANSI S3.34 was first published. In response to these improvements and the introduction of the EU Human Vibration Directive, ANSI Working Group S2.39 developed the revision to ANSI S3.34, which has now been published as ANSI S2.70-2006.2 Method ANSI S2.70 specifies the use of the hand-arm vibration measurement procedures outlined in ISO 5349, Parts 1 and 2.2,4,5 It requires the measurement of ISO frequency-weighted acceleration values in three mutually orthogonal axes of vibration. These values are then vectorially added to obtain the vibration total value, ahv: [ ] where ahwx, ahwy, and ahwz are the measured r.m.s. ISO frequency-weighted acceleration values in the x, y, and z directions, respectively. If multiple vibration exposure events are experienced during a work day, the overall vibration total value is obtained from: [ ] where ahvi is the vibration total value of the ith operation, Ti is time duration in hours of the ith operation, n is the total number of operations, and T is total time in hours associated with the n

Jan 6, 2006

In 2007, a total of 725 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Nonmetal mines com-prised 4.9% of all m ining operations. ? Mines producing common clay comprised 25.4% (n=184) of all nonmetal mining operations. ? Nonmetal mining operations were located in all states and territories except Alaska, Delaware, Hawaii, Maine, New Hampshire, Rhode Island, Puerto Rico, and the U.S. Virgin Islands.

Aug 1, 2009

By D. B. Eccleston

Natural gas and mixtures of natural gas and hydrogen were used as fuels in a laboratory engine to determine the relationship of emissions to air-fuel ratio and to establish practical lean limits for air-fuel ratio. Synthetic gas manufactured from coal (Synthane) and natural gas were used as fuels in a vehicle to obtain comparative data on emissions and performance. Results showed that lean limits for air-fuel ratio when using hydrogen-enriched natural gas were extended significantly beyond Chat of natural gas. Synthane pro¬duced exhaust that was significantly less reactive than exhaust from natural gas. With lean air-fuel ratios, the acceleration performance of a vehicle fueled with Synthane was improved over its performance when fueled with natural gas.

Jan 1, 1972

By E. J. Murphy, John C. Holtz

"INTRODUCTION Toxic gases in the products from the detonation of explosives are one of the hazards in blasting underground. Investigations by the Bureau of Mines 4/5/ have shown that the oxygen balance of the explosive is an important factor in the control of toxic gases. This balance is considered in determining the composition of modern metal-mining explosives for blasting underground, and application of the concept has reduced the volume of toxic gases generated.The chemical nature of the material being blasted also influences the composition of the toxic gases produced. Under some conditions of blasting in massive pryrite, unsafe concentrations of sulfur dioxide and hydrogen sulfide have been found.Experiments with the O-J apparatus 8/ have shown that there is an increase in the volume of carbon monoxide in the gaseous products when permissible explosives are detonated in contact with coal dust. Thus, reactive materials of a reducing nature adjacent to explosives loaded in drill holes may decrease the effective oxygen balance of the explosive and cause the volume of toxic gases to increase.Several blasting accessories of reducing nature have been introduced recently for use in coal or metal mines or tunnels. In practice these are loaded adjacent to the explosive where conditions favor reaction with the products of detonation. The effects of this loading on the gaseous products obtained from the shot are indicated in this report. Broad consideration was not given the efficiency, usefulness, or over-all safety of these devices, but the practical significance of the hazard resulting from increased volume of carbon monoxide is discussed."

May 1, 1942

By Lloyd Williams

A vertical air shaft in the Birmingham, Ala., iron district was sunk with a circular cross section and lined with concrete at a relatively low cost to provide needed ventilation for an iron-ore mine. The method of sinking the shaft is described, and the costs are stated in mar-hours with a descriptive list of equipment and a statement on the size and use of temporary buildings. Preparation began May 2, 1955, and the shaft was completed at a depth of [680] feet by September 22, 1956. By October 1956, all temporary building and [aft]-sinking equipment had been removed. The total direct-labor cost for the operation, including preparation and dismantling, was 50,700 man-hours, or 30.2 man-hours per foot. Total rock and dirt removed amounted to 17,523 cubic yards (in place), and the shaft lining required 4,635 cubic yards of concrete to form a circular air shaft with an inside diameter of 16 feet.

Jan 1, 1960

By Jerry G. Craig

The Bureau of Mines has developed a computerized oil and gas well data retrieval system from studies of the waterflood potential of a producing reservoir. This system stores pertinent information about each well completed in a reservoir and facilitates selection and manipulation of large volumes of data. Use of the system enables reservoir information to be supplied rapidly, accurately, and at less expense.

Jan 1, 1971

By P. C. McWilliams

The Bureau of Mines investigated ground support problems in four major block-cave mines to assess the current "state-of-the-art" and to delineate areas for future research. The most significant problem is the inability of present support systems to hold moving ground. Further, as mining progresses to greater depth, this problem becomes more serious. Providing adequate temporary support capable of withstanding primary and secondary blasting is the next most significant problem. A detailed analysis of the effect of mining methods on support problems is also recommended for future research.

Jan 1, 1975

By S. H. Ash, E. M. Brooks

"Many of the hoisting slopes at the mines in the State of Washington are driven on extra steep dips. To facilitate hoisting they are driven wide enough to provide two tracks. The cars are handled by high-speed, first-motion electric hoists and the trips run in balance.The State mining laws a provide that special man-cars be provided on slopes of 20° or more and that no one be allowed to ride while any loaded car is being hoisted in any slope in a mine. Obviously, in addition to the fact that it is more or less hazardous to ride while an empty trip is being hoisted, considerable hoisting time is lost during the day if some one has to ride the trips in the slope.Owing to the locations of pumps and various types of equipment, more or less travel is required up and down the slope. Not only to provide a proper safety factor but also to comply with the law, some other means of transportation in an¬other passageway is desirable. This is sometimes recognized in large mines by pro viding separate hoisting shafts, or slopes, and necessary equipment, which are use for transporting men and material. The handling of material in itself would justify the system in most large mines.The following description of an automatic electric man-hoist was prepared from data furnished through the courtesy of Mr. Thomas Murphy, superintendent of the Northwestern Improvement Company's mines in the Roslyn-Cle Elum coal field.The special features of this hoist are that no hoistman is required and its operation is always under the control of the person or persons riding the trip.The hoist was installed at mine No. 5, Roslyn, Washington, to provide a means of entering and leaving the mine on idle days or at night when no hoistman was on duty and to make it unnecessary to use the main hoist for a man trip during working hours. It has been in operation for about two years and has given very satisfactory service.The hoist, with all accessories, is housed in a concrete building 200 feet back from and in direct line with one of the main airways. One car with a capacity of six men operates over a distance of 1,200 feet on a 38° pitch.The wiring details of the electric circuits which control the operation of the hoist are shown in Figure 1-a.The hoist is driven through a worm gear by a 500-volt shunt-wound direct-current motor at a car speed of 120 feet per' minute. A gravity friction brake with magnetic release is mounted on the- motor shaft and is wired in multiple with the motor field coils. The hoist drum is also equipped with emergency friction brakes, which operate by gravity and are released, in case of overspeed, by the governor geared direct to the drum shaft. When these brakes set the control circuit is opened at contact 2E-2C and the motor stops.If the descending car meets some obstruction and is stopped, the hoist continues to run and unwind the rope. To guard against this occurrence, a weighted sheave wheel rides the rope 4 feet from the drum, and if the rope becomes slack the rider drops downward and opens the contact 2C-2E which stops the hoist.Limit switches, S1 and S2, are located on the hoist indicator, which is connected to the drum shaft through sprockets and chain. The pointer P indicates the position of the hoist at all times."

Jul 1, 1930

By Oliver Bowles

The United States has never attained importance as a producer of asbestos, the domestic output being only 1 to 3 percent of the quantity required to supply raw material for its extensive asbestos-product manu- facturing industries. Production is centered in four principal countries-- Canada, Rhodesia, Union of South Africa, and the Soviet Union. Since asbestos first became an important commercial commodity the Province of Quebec, Canada, has led in tonnage produced, but a large proportion of the output of this province is shorter, nonspinning grades. Since 1916 the Union of South Africa and Rhodesia have become increasingly important as sources of the higher-grade spinning fibers. Before the World War Russia ranked next to Canada as a producer of asbestos, but during the revolution- ary period the industry in that country was almost at a standstill. In 1926, however, activity was revived, and each year since then production and exports have increased greatly. Minor quantities of asbestos are produced in Cyprus; Australia, Finland, and several other countries. Chrysotile is the leading product in all the producing countries, but substantial quantities of both blue (crocidolite) and brown (amosite) asbestos also are produced in the Union of South Africa. Minor quantities of anthophyllite and similar amphibole varieties are mined in the United States, Italy, Bulgaria, Finland, and several other countries.

Jun 1, 1934

By R. Havens

During investigations of the occurrence of manganese in the western United States in the early 1940?s, examining engineers of the Bureau of Mines collected samples from seven claims and mines in southern Arizona. For convenience in reporting the results, the work on the properties is grouped in three districts. As the ores were too low grade to be acceptable to producers of ferromanganese, beneficiation studies were made to determine the amenability of the ores to concentration. The San Fernando group is about 10.5 miles south of Patagonia in the Harshaw mining district. G. T. Humphries and D. Alonso held an option on the property, which was owned by H. Bender. Two samples were taken; 1 was a picked sample and the other a representative sample of ore as exposed in the mine.

Jan 1, 1954

By Nicholls Harry R.

The Bureau of Mines studied the effect of varying the, diameter of explosive charges on the generation and propagation of strain waves. The parameters compared were strain amplitude, impulse, energy, and pulse shape. Three different explosives were detonated in three different charge diameters. Charges of cast 50/50 pentolite-detonated at the same velocity in 5-, 2.5-, and 1.5-inch diameters. Charges of ammonium nitrate-fuel oil prills and 45-percent semigelatin dynamite showed a strong detonation rate-diameter dependency. Detonation of these two explosives was considered nonideal. Differences in the diameter of the charge caused less difference in the strain-generating abilities of pentolite than in those of the other two explosives. This was also true for impulse and energy. Rise and fall times of the strain pulses for all three explosives were proportional to detonation time and cavity volume, respectively.

Jan 1, 1966

By Steven W. Schmauch

The Farlin Creek study area encompasses 610 acres managed by the Bureau of Land Management in Beaverhead County, Montana. A mineral survey was conducted by the U.S. Bureau of Mines and U.S. Geological Survey in 1984. Bureau of Mines personnel reviewed literature and county mining records, and examined prospects or mineralized areas to determine its mineral potential. Geological Survey personnel evaluated the area by geochemical sampling and geophysical surveys. The study area is included in the Mount Baldy mining district. Nearby mineralized Quartz veins or tactite bodies apparently do not extend into or exist within the study area. No significant gold or economic detrital minerals were found in samples from streams draining the area. All of the study area is leased for oil and gas.

Jan 1, 1985

By W. A. Calhoun

"INTRODUCTION A letter from S. D. Strauss, vice president of Metals Reserve Company, Washington, D.C., dated May 22, 1945, to the chief of the Metallurgical Branch, Bureau of Mines, in Washington; includes the following: Because of the present critical shortage that exists in the supply of corundum required by certain industries in war production, the Reconstruction Finance Corporation, Mr. W. C. Keeley, Vice Chairman for Metals and Minerals, War Production Board, has recommended that the Reconstruction Finance Corporation though Metals Reserve Company, proceed with preliminary mill testing of the corundum ore in Gallatin County, Montana, and that the results of that testing be transmitted to the War Production Board. If the results of the testing work are considered satisfactory, Metals Reserve Company will then provide for the actual mining and milling of the ore for the production of corundum concentrates.Pursuant to the above stated recommendation by the War Production Board, Metals Reserve Company desires to make -use of the facilities of the Bureau of Mines testing plant at Rolla, Missouri, for conducting sink and float and other concentration tests on representative samples of the Montana corundum ore. Two, and possibly three samples of ore are to be tested which will have an aggregate weight of approximately 50 tons."

Dec 1, 1947