Search Documents

By Noel N. Moebs

This report summarizes a Bureau of Mines study on the use of geotechnology to identify and reduce ground control hazards at slate quarry operations in eastern Pennsylvania. The major ground control hazard is falling rock, attributed to weathered bedding plane faults, which weaken quarry highwalls. It was demonstrated that these faults can be detected outside of the quarry perimeter using surface resistivity measurements. Falls of ice from quarry highwalls constitute a second major hazard, which requires water diversion as a basic control method. In situ stresses seemingly cause only minor problems in slate extraction although they could interact with developed stresses and lead to failure of barriers between quarries. Pull tests showed that rockbolts anchor firmly in slate and should prove effective in securing loose rock.

Jan 1, 1986

By Hillary W. St. Clair

This is an initial progress report on a theoretical study of the iron blast furnace. The purpose is to develop a thermochemical model that will simulate mathematically a real furnace. An analysis is made of the behavior of a hypothetical furnace, operating adiabatically on pure ferric oxide, graphitic carbon, and dry air. Relationships are derived for carbon consumption, gas composition, and reaction temperature for a furnace operating at steady state, and in which the smelting rate is slow enough for the gas and solids to approach thermal and chemical equilibrium. Analyses are made for two contrasting types of gas flow: (1) Nonturbulent flow, having no vertical mixing; and (2) turbulent flow, having perfect mixing during each step of the process. It is shown that some vertical mixing is essential for complete reduction of ferrous oxide and that the extent of vertical mixing is one of the critical factors in the behavior of the furnace, This analysis indicates that the thermochemical relationships in a blast furnace can probably be best simulated by a finite series of gas-solid reactors through which gas and solids flow countercurrently and in which the temperature and composition of gases and solids are assumed to be uniform. Any degree of vertical mixing can be approximated by the proper choice of the number of reactors.

Jan 1, 1963

By H. Tomlinson

Fatalities from falls of roof and coal are responsible for the death of more than 1,000 miners annually in the bituminous coal mines of the United States, or practically one-half of the total fatalities in and about these mines. The men are killed by falls singly or in small groups and little or no publicity is given these accidents as they lack the spectacular features of gas and dust explosions. As a result, the public and even the miners have the impression that accidents from falls of roof and coal are just one of the unavoidable hazards of the coal-mining industry. This belief is not true. Accidents caused by falls can be avoided largely by the application of sound engineering principles, by education, and by proper leadership in the industry, just as gas and dust explosions and accidents caused by explosives have been reduced in recent years.

Jan 1, 1933

By H. Tomlinson

Fatalities from falls of roof and coal are responsible for the death Of more than 1,000 miners annually in the bituminous coal mines of the United States, or practically one-half of the total fatalities In and about these mines. The men are killed by falls singly or in small groups and little or no publicity is given these accidents as they lack the spectacular features of gas and dust explosions. As a result, the public and even the miners have the impression that accidents from falls of roof and coal are just one of the unavoidable hazards of the coal-mining industry. This belief is not true. Accidents caused by falls can be avoided largely by the application of sound engineering principles, by education, and by proper leadership in the industry, just as gas and dust explosions and accidents caused by explosives have been reduced in recent years. The necessity for studying falls of roof and coal becomes apparent by referring to the following data from a table by Adams and Chenoweth:3

Jan 1, 1933

By Paul W. Johnson, Ralph C. Kirby, Frank A. Peters

Alumina can be recovered from clay , using 30 percent nitric acid for digestion . Calcined clay is crushed and then digested at 325 ° F and 85 psig pressure with less than stoichiometric nitric acid required to form normal aluminum nitrate . In this way , a solution containing both normal aluminum nitrate , Al ( NO3 ) 3 , and basic aluminum nitrate , assumed to be Al ( OH ) ( NO3 ) 2 , is formed , and in which iron is virtually insoluble . The solution is filtered and then concentrated in vacuum evaporators to crystallize normal aluminum nonahydrate . The crystals are washed with 50 percent nitric acid and then decomposed to alumina and nitrogen oxides . The design that has been developed for this process is based on published work . For a plant producing 1,000 tons of alumina a day , the estimated operating cost is $60.69 per ton of alumina , and the estimated fixed capital cost is $ 76 million using a Marshall and Stevens chemical equipment index basis of 240.0 . This process is not competitive under current economic conditions with the production of alumina from bauxite via the Bayer process . For lowering costs , future research should include study of leaching at lower temperatures under atmospheric pressure and alternate aluminum nitrate decomposition methods .

Jan 1, 1964

By E. D. Palmes

A new type of personal sampler for quantitative estimation of atmospheric concentrations of contaminant gases was first reported from this laboratory in 1972. The sampler requires no pumps or flow regulators and employs instead the motion of the gas molecules them-selves to furnish the power for sampling. Under this grant, work was completed on development of a kit for the field determination of both NO2 and NO. Detailed instructions for the preparation of the samplers and the use of the kit was supplied to the Technical Project Officer. Attempts were made to adapt the same type of sampler to the measurement of SO2 and CO. Both gas chromatographic and turbidimetric procedures for the final estimation of the S02 proved to be unsatisfactory. For CO no reagent was found which would react sufficiently rapidly with this gas to utilize the essential feature of the diffusion sampler, the maintenance of a diffusion gradient which is at least approximately numerically equal to the ambient concentration. A number of publications on use of the NO2 sampler, both at occupational and community air pollution levels, have resulted from this work.

Jan 1, 1979

By D. Harrington

The record of fatalities from mine explosions during the past 2 fiscal years has been anything but encouraging; more men were killed by explosions (379) than were killed from the ante cause during to' preceding 6 years combined (368). The reason for the large increase in the number of explosion fatalities during the past 2 years as compared with the previous 6 years is not entirely clear. In some instances, there has been laxity in the enforcement of State mining laws; in others, both workers and operating officials is have failed to observe recognized precautionary measures to prevent explosions. In many of the explosions that lave occurred within the asst few years in mechanized mines it has been evident that speed of operation and a demand for maximum tonnage at minimum cost resulted in neglect of ordinary safety measures.

Jan 1, 1942

By Lowell Stroud

Ten natural gases containing from 0.023 to 8.4 percent helium were investigated. In seven high-helium samples, the isotopic abundance of Ne21 was greater than in the atmosphere, being supplemented by 33 to 85 percent of "excess" or "radiogenic" Ne21. The ratio of He4/Ne21(rad) in these gases was evaluated and found to vary between 2.9 x 107 and 5.9 x 107 , a factor of approximately 2. Argon concentrations were determined by the isotope dilution method. The isotopic ratios of Ar40/Ar36 in the high-helium gases were from 5 to 75 times the atmospheric value, with the Ar40 being about 80 to 99 percent radiogenic in nature. The ratios of He4/Ar40(rad) in all 10 gases were evaluated and found to range from 4 to 18. The isotopic ratio of N14/N15 in four of the high-helium gases was essentially the same as in the atmosphere; in three cases it was approximately 5 percent higher than the atmospheric value of 272.0. The genesis of nitrogen and the relationship of nitrogen to helium in natural gases were reviewed and are discussed in terms of a theory for the concurrent generation of nitrogen, helium, radiogenic neon 21, and petroleum (hydrocarbon gases and liquids).

Jan 1, 1967

By E. C. Perkins

This report describes a ferric chloride trap, based on formation of a low-melting sodium chloride-ferric chloride mixture of near-eutectic composition, and its use in chlorination of impure titaniferous materials. The trap is placed in the hot gas stream between the chlorination reactor and the condenser. Virtually all of the iron is removed by the trap. The condensed titanium tetrachloride is free of suspended solids and contains only a trace of iron. Four examples are given of the use of the ferric chloride trap in chlorination of impure titaniferous materials. INTRODUCTION In the Kroll process, ductile titanium metal is produced by reducing titanium tetrachloride with magnesium metal.4/ In commercial practice, titanium tetrachloride is produced by chlorinating titaniferous materials in the presence of carbon.2/ In 1957 most producers were using rutile, and virtually all plants were designed for its use. About four-fifths of the domestic consumption of rutile was imported from Australia. The Bureau of Mines, under provisions of contract DMP-116 with the General Services Administration, studied electrosmelting of domestic ilmenites and titaniferous magnetites to produce high-titanium slags with pig iron as a byproduct. Under the same contract, chlorination studies also were being made of these slags. Smelting was done at the Northwest Electrodevelopment Experiment Station, Albany, Oreg., and chlorination at the Electrometallurgical Experiment Station, Boulder City, Nev.

Jan 1, 1958

By H. L. Riley

At the Southern Experiment Station, Tuscaloosa, Ala., reports are prepared from time to time on results of washability studies of coal from important beds in the Southern Appalachian region. The investigations that provide the material for these reports are made by the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and the mine operators. The principal objective of a washability study is to obtain technically and commercially important data to aid in determining the best methods for preparing and utilizing the Nation's reserves, particularly of coking coals. Such information is also important from the standpoint of conservation, because it facilitates the selection of preparation methods that will yield an acceptable product with a minimum loss of coal to the rejects.

Jan 1, 1958

By J. E. Conley

Available statistics show that the demands of the American chemical industry for sodium sulphate have been increasing slightly in recent years. The supply from domestic sources, particularly In the form of byproduct salt cake from the acid manufacturers, has been tending to decrease due to the growing manufacture of synthetic acid. Both hydrochloric and nitric acids are being synthesized from their elements. The natural result has been that a smaller amount of salt cake is available. Simultaneously, the expansion of the Kraft paper industry, especially in the South, has brought about greater demand for sodium sulphate in that section. This dean is being met by domestic byproduct salt cake, by imported German sodium sulphate made from potash waste liquors, and by favorable situated domestic deposits of Glauber salts and tile anhydrous salt, thenardite. No shortage of natural sodium sulphate exists in the United States, but usually such deposits occur in semiarid regions far removed from transportation facilities and from markets. Moreover, the major portion of the natural deposits is Glauber salt or mirabilite (Na2SO4 ? 10H20), which must be dried or dehydrated in order to meet consumer requirements. The water of hydration represents, roughly, 55 percent of tae total weight of the crude salts and therefore has a very important influence on transportation costs. In marry instances the cost of getting, even the dehydrated product to market is the deciding economic factor. Therefore, the recovery oil production of anhydrous sodium sulphate from plant-.waste liquors or from natural brines of suitable composition might be economically feasible. The U.S. Bureau of Mines, at its nonmetallic Minerals Experiment Station, New Brunswick, N. J., has, for a number of rears, been investigating the commercial possibilities of treating the complex saline mineral polyhalite (K2SO4?NgSO4?2CaSO4?2H20) for the recovery of potash and magnesia. Certain proposed processes (1, 2, 3, 4)4/ yield waste liquors that contain the bulk of the magnesium and sulphate originally combined as magnesium sulphate in the polyhalite molecule. Sodium chloride In limited concentrations is also present, as extensive beds of salt occur in strata overlying the polyhalite deposits. A typical waste liquor would contain:

Jan 1, 1936

By H. E. Heide

The serious shortage of domestically produced asbestos during the war prompted the Bureau of Mines to investigate reported asbestos deposits in Alaska. The most promising' appeared to be these in the Cosmos Hills and Jade Hills areas along the Kobuk River in northwestern Alaska. The deposits along the west side of Shungnak River, a tributary of the Kobuk River, were the first to be investigated by the Bureau, in the summer of 1944. Four bulldozer trenches were excavated, from Which a 2-ton sample was taken. This sample was shipped to Rolla, Mo., for testing in the Bureau of Mines laboratory. In the summer of 1945 an investigation of asbestos deposits on Cosmos Creek, also a tributary of the Kobuk River, was begun; the work was completed during the field season of 1946.

Jan 1, 1949

By W. F. Watts

The U.S. Bureau of Mines has conducted research on methods to reduce and to measure diesel particulate matter (DPM) aerosols in underground coal mines. One objective of this report is to present findings from an investigation of the DPM reductions obtained by an engine-mounted integrated control system consisting of a dry system (DS) and a diesel particulate filter (DPF). Another objective is to present results from the usc of a size selective personal sampler to measure DPM concentrations in an underground coal mine. Bureau laboratory tests of the integrated dry system and diesel particulate filter (DS-DPF) have shown that DPM emissions can be reduced up to 97 pet with little change in gaseous emission concentrations. The DS-DPF is undergoing certification tests conducted by the Mine Safety and Health Administration (MSHA). Subsequent to passing all safety requirements, it will be tested in an underground coal mine. A baseline survey of DPM concentrations and aerosol size distributions in a cooperating mine was completed in August 1988. A prototype DPM personal sampler was tested during this survey. Based on results from this test, an improved unit has been developed. This unit is scheduled for extensive field testing by MSHA in 1989.

Jan 1, 1989

By Michael J. Potter

Native asphalt was produced by five companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by White Uvalde Mines and by Azrock Industries Inc., Uvalde County, TX. In June, Azrock Industries was purchased by the R L. White Co. Gilsonite, a solidified hydrocarbon found only in Utah and Colorado, was mined by American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California); by Ziegler Chemical and Mineral Corp.; and by Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation) from properties in Uintah County, UT. Gilsonite is used for a variety of purposes including automobile bodysealer, light-weight aggregate for cement used in oil well drilling, asphaltic building board, protective coverings, anticorrosive paints, and roofing compounds.

Jan 1, 1985

By D. R. Tesarik

As part of its research program to investigate ways of improving resource recovery and reducing subsidence, researchers from the U.S. Bureau of Mines placed instruments in the B-North ore body of the Cannon Mine, Wenatchee, WA, to monitor cemented backfill and rock deformation during mining. The vibrating-wire gauges proved to be reliable and versatile, and approximately half of the instruments are providing data after 2 years of use. A two-dimensional, finite-element model was used to analyze the Cannon Mine's multilevel bench cut-and-fill mining method and predict rock and backfill displacements. The model accurately predicted rock displacements, but the predicted and measured displacements in cemented backfill had a correlation coefficient near zero, indicating that the model should only be used to predict rock displacements and not backfill displacements. A finite-difference model was also used to evaluate the stability of a cemented backfill pillar. Results can be used to conservatively predict backfill stresses, but on-site observation of pillar failures coupled with in situ measurements are needed to make more accurate predictions. An ongoing evaluation of the mining system has indicated that filling the primary stopes tight to the back with cemented backfill allowed these pillars to carry overburden loads soon after the cemented backfill was placed.

Jan 1, 2010

By Hon-Yim Ko

The properties of coal from the Pittsburgh seam, procured from the Bruceton and Federal No. 2 Mines were found to be similar. Strength and stiffness properties of Beehive Mine coal were determined and the material found to be isotropic. Mechanical, index and geologic properties of roof and floor coal measure rocks from Beehive mines were measured and correlated. Analytic formulations are given for coal creep under uniaxial loading, while triaxial creep is being investigated. Results of testing of coal model structures are compared with predictions from using several material models.

Jan 1, 1976

By K. O. Bennington

Cancrinite is one eonstituentof "red muds," a high-volume waste product of alumina production by the Bayer process. The Bureau of Mines determined the thermochemical properties of cancrinite as part of a program to provide such data for minerals of industrial importance. Cancrinite [Na7.68(A16Si6024)(N03)1.68 (H2O)4.1] was synthesized by reacting aluminum silicate gel with a solution of NaOH and NaN03, and the composition was determined by chemical analysis, differential scanning calorimetry, and thermogravimetric analysis. The heat of solution was determined by hydrofluoric acid solution calorimetry. The standard enthalpy of formation at 298.15 K, ?Hf°298, is ?Hf°298 = -3,487.97 ±2.6 kcal/mol, and the standard enthalpy of formation from the oxides and NaN03, ?H°298, is ?H°298 = -215.20 ±l.8 kcal/mol.

Jan 1, 1983

By J. H. Nixon

A three phase program evaluated commercial proximity warning devices, developed and designed a microprocessor-based electrostatic field measurement instrument, and utilized this instrument to investigate the electro-static fields about power lines. The Phase I program consisted of test and evaluation of these commercially available proximity devices. The evaluation results were reported in the Phase I report entitlted "Evaluation of Proximity Warning Devices II dated 22 February 1980. The Phase II program resulted in the design and development of a microprocessor-based Distributed Sensor A.C. Electrometer which measures the electrostatic field present at 17 discrete locations along a crane boom. Operator control of the measurement system allows simultaneous electric field measurements from 17 probes, print out of the electric fields measured, and data archiving on magnetic tape for post measurement analysis. Under the Phase III program, electro-static fields around a crane boom were measured by the instrument at 17 high voltage power lines of various voltages and geometries. The electric field data was processed and plotted versus boom distance from the power line. Analysis of the electric field data indicate that the distances at which a single sensor alarm will activate, vary by a factory of 3 to 1. This is due primarily to variations in boom orientation. The results also indicate that in the case of multiple power lines, a single electrostatic field sensor cannot reliably be used to determine the distance from a power line.

Jan 1, 1982

By Joseph A. Holmes

The investigations carried on at the fuel-testing plant of the United States Geological Survey at St. Louis in 1904-1907 included tests of the steaming and gas-producing qualities of many coals and of the possibilif3 of their improvement by briquetting, together with washing and coking tests and tests of some of the resulting coke in the cupola. These tests were part of a general inquiry into the manner of utilizing most efficiently each of the coals under investigation. The equipment used in the cupola tests of coke, the manner of conducting the tests, and the essential results have been described in publications of the Geological Survey," and only the more important conclusions to be drawn from the tests are mentioned in the following pages. The tests were made to show the fitness of the cokes for foundry purposes, but an incidentlll result was to show foundry men and the coke producers the advisability of studying the conditions of foundry practice. The present bulletin, published by the Bureau of Mines because the analyzing and testing of fuels have been transferred from the Gilological Survey to the Bureau of Mines, briefly reviews the status of the coke industry, some features of practice in the use of coke in the foundry, the probable happenings of a cupola heat, and the reasons for modifying charging practice so that a particular coke can be used to best advantage.

Jan 1, 1910

By L. C. IlsLey

"During the last eight years there has been a noticeable increase in the use of permissible equipment in gassy and dusty coal mines. This trend has undoubtedly been toward greater safety in mining, but in spite of this all is not well ""along the front.""In many mines those in charge, either through ignorance or supposed economy, have neglected to install sufficient copper and maintain good bonding on the rails used for return circuits to have a safe working voltage for the permissible equipment which is intended to afford them safety.Low voltage, when properly analyzed, is not economy but frequently is an expensive oversight. Burned-out armatures, controllers, rheostats, and switches are costly in themselves to repair or replace, but the greatest cost in many instances is the loss of production resulting from idle and broken-down equipment.From a safety standpoint, excessive low voltage where permissible equipment is necessary is almost criminal negligence. A burn-out of any kind is liable to cause an arc that may burn its way through a casing wall and bring about a hazardous condition if gas or dust in explosive proportions should be present. Again, all wiring, both interior and exterior to the apparatus, is subject to the extra heating consequent upon low voltage. It should be remembered that if the voltage drops the current must increase a corresponding amount in order that the same work may be accomplished; and as the heating effect is as the square of the current, an enormous overheating of the electrical parts and wiring often takes place. This heating effect is especially detrimental to trailing cables used on portable equipment, because under the most favorable conditions the size of cable selected is only barely sufficient to do its work properly at a safe working temperature; therefore, when the extra current load is added because of poor voltage, overheating is sure to result, with consequent deterioration of the insulation, This effect greatly increases the liability of cable failures in service, and in turn adds to the hazards incident to the use of portable equipment of the permissible type involving the use of trailing cables.Some manufacturers have tried -to protect their equipment from low voltage, especially below a certain point, by -installing low-voltage relays which will trip when the voltage falls to a predetermined value. It is understood that some operators have hesitated or refused to install such low-voltage protection because they were aware that the voltage conditions were so poor that the equipment could not operate under the safe limits set. It is difficult to understand how any progressive company that is willing to go to the ex-pense of installing permissible equipment could be so shortsighted in this phase of common sense, safety, and economy."

Dec 1, 1929