Search Documents

By L. D. Johnson

On a project which is to develop a system to suppress coal dust explosions, a facility has been built and several devices tested. The facility is a 317-foot, 4.5-foot diameter shock tube and to date 53 tests have been carried out with methane-air and methane/coal dust-air as the explosive mixtures. Suppression of slowly propagating (up to 300 ft/sec) flame fronts has been successfully carried out on two tests using the dry chemical extinguishing agent Purple K. Delivery of the material directly into the flame front Seems to be required if effective suppression is to be accomplished.

Jan 1, 1972

By Harmon E. Keyes

Many organizations, including the Bureau of Mines, have made intensive studies of the application of leaching methods to relatively small low-grade disseminated deposits of copper ores, containing both oxide and sulphide minerals. One of the principal difficulties has been to obtain a solvent that could be made at a low cost and would effectively dissolve the copper minerals. Another drawback has been the high initial cost of a plant and the refined type of mechanism ordinarily required by standard practice for carrying out the leaching cycle. The Bureau of Mines has attempted to develop a cheap and efficient solvent that would especially meet the requirements of smaller plants. (See Bibliography.) It has been known that dilute ferric sulphate-sulphuric acid solution is an excellent solvent for most copper minerals, such as chalcocite, bornite, and oxidized forms, but not for chalcopyrite and certain silicates. A method of producing this solution from sulphurous products and waste liquors was developed by the bureau and tried successfully on a test-plant scale at the Southwest Experiment Station in cooperation with the department of mining and metallurgy, University of Arizona, Tucson, Ariz. However, this work did not involve the actual leaching of ores with the solutions thus produced or the cyclic use of the iron solutions in the regenerator cell. Except for certain laboratory tests, in which known impurities were added, no data were available to show the effect on regeneration if accumulations of impurities were built up in the leaching circuit.

Jan 1, 1930

By Ned H. Snyder

In recent years the Government and other large consumers of coal have appreciated more and more the desirability of definitely determining by chemical analysis and test the character and quality of the coal they purchase. Higher prices for coal point forcibly to the need of giving more study to engine room and boiler room efficiencies and economies; this implies an intimate knowledge of the character and quality of the fuel used. Analyses and tests of delivered coal furnish data whereby power plant results can be comprehensively studied and a continuous check maintained on the coal and on the conditions of plant operation. Under authority of acts of Congress making appropriations for technologic investigation of fuels and the analyzing and testing of fuels belonging to or for the use of the United States Government, a laboratory is maintained at the Pittsburgh station of the Bureau of Mines, where samples representing deliveries of coal purchased for Government use are analyzed and tested. The Bureau of Mines has been active in promoting the purchase of coal by the Government under specifications/ that is, by contracts that make definite requirements regarding the heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analysis. Under many of these specification contracts the bidders guarantee the quality of the coal offered, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled and analyzed to determine whether the coal is of the quality guaranteed by the contractor, and if it is not, the price to be paid is decreased in proportion; but if the coal is of higher quality, the price is proportionately increased. The known analyses of coals or the guaranteed analyses offered by the bidders may sometimes be used for determining the award of a contract, but if the coals offered differ widely in characteristics, it may be difficult to determine which would prove the cheapest fuel without data on their relative evaporative efficiencies. Hence, the making of evaporative tests under service conditions may be necessary in order to determine which coal is particularly adapted for successful and economical use in a certain plant. Once a particular coal is selected, however, regardless of the procedure of determining the award of a contract, then the greatest advantage of the specification method is realized, for it guarantees the purchaser receiving coal of uniform character and quality, thereby insuring the best results in the plant. The success of the specification method for the purchase of coal and the reliability of analysis now rests largely on sampling.3 Improper sampling leads to controversies, with resulting condemnation of the specification method in general and of the value of laboratory analyses and tests in particular.

Jan 1, 1922

By James C. Barker

Unverified reports of rare earth element (REE) concentrations in gold placers and radioactive mineral prospects in the Zane Hills were investigated by the U.S. Bureau of Mines as part of the Alaska critical minerals program. REE is reported to occur in dredge concentrates at the Hogatza mine and up to 1.2 pct REE was previously analyzed in alkalic syenite (bostonite) dikes marginal to the pluton. In addition, numerous thorium-rich veins, explored for their uranium content but unevaluated for REE, occur on the western margin of the Zane Hills. The Bureau mapped and sampled all of the reported or suspected REE occurrences. Dredge concentrates contain abundant uranothorianite, a mineral species which incorporates cerium subgroup REE. Bostonite dikes occur in conjunction with a multi-phased zoned alkalic intrusion, however, no significant REE concentrations were found. Thorium-rich veins contain nil to 0.5 pct Y but resource potential is limited by this relatively low grade, the ultimate low tonnage potential, and the lack of uranium as a major economic element. The Zane Hills exhibit attractive exploration targets for uranium deposits, primarily in a sedimentary form. Gold may be found peripheral to the pluton in both placer and lode deposits. Resource potential of REE, however, appears limited to a placer by-product of REE-Zr-Ti that is recoverable only during large scale gold placer mining. Placer exploration of the lower Wheeler and Dakli Creeks is suggested.

Jan 1, 1991

By J. C. Gerdeen

SAP-S information on the following element types are included in this appendix: Type 1. Three-Dimensional Truss and Bolt Element Type 4. Two-Dimensional Finite Elements Type 8. Variable-Number-Nodes Thick Shell and Three-Dimensional Elements Type 9. Two-Dimensional Joint Element (to be used with Type 4 elements) Type 10. Three-Dimensional Joint Element (to be used with Type 8 elements) Additional SAP4 elements, Types 2, 3, 5, 6, 7 and 12, are also contained in SAP-S and information on these elements is readily available in any SAP4 user's manual. These elements are as follows: Type 2. Three-Dimensional Beam Elements Type 3. Plane- Stress Membrane I-r .n Elements Type 5. Three-Dimensional Solid Elements (8 Node: Brick) Type 6. Plate and Shell Elements (Quadrilateral) Type 7. Boundary Elements Type 12. Three-Dimensional Straight or Curved Pipe Elements

Jan 1, 1976

By J. W. Miller

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and, from the data developed, to determine: (a) Which coals, either as mined or after beneficiation by conventional preparation, are suitable chemically under present standards for producing metallurgical coke. (b) Which coals require special and more intensive treatment in preparation than is now practiced. (c) Which coals cannot be considered potential sources of metallurgical coke, regardless of preparation. This report is one in a county series and describes the preparation characteristics of the coals of Logan County, W. Va. According to present-day standards for metallurgical coal, many believe that the sulfur content of the coal should not exceed 1.25 percent? Coal with more than this amount has been used for making metallurgical coke, especially when blended with coal containing less sulfur. In this series of reports 1.25 percent sulfur is used as a gage to determine whether or not a coal will be suited for metallurgical coke.

Jan 1, 1957

By C. J. Walker, J. S. Miller

This work was done in an attempt to find a simple solution to the problem of simultaneously changing terminal rate and terminal pressure under conditions of unsteady - state flow in porous media . Although the original aim was not realized , a method for encasing a sandstone core that would permit high - pressure ( 200 to 980 psi ) flow tests and the use of electronic equipment to measure pressures at points along the core during unsteady - state gas depletion was found to be feasible . The sandstone core used in this study was from the Bandera formation of Pennsylvanian age , Redfield , Kans . The core , cylindrical in shape with a 3.5 - inch diameter and 6- foot length , had a porosity of 15 percent and a permeability of 9 millidarcys .

Jan 1, 1963

By Richard Rittenhouse

This program was to develop a new base line system for automated continuous room and pillar type mining. The primary requirement estab¬lished for this machine is that the machine be capable of mining and bolting simultaneously. Additionally, this machine was to provide temporary and permanent roof control, have a productive - full - face semi-automatic mining system, leave a clean entry outby the machine, provide maximum operator protection, provide effective dust suppression and provide air scrubbing to restrict respirable dust to permissible levels. The machine has effectively demonstrated the ability to mine and bolt simultaneously. Additional above ground operation, testing, and time studies are recommended to further verify the machines abilities. Design improvements are recommended for future generation AES machines. These relate to marginal design areas such as side loading on vent duct lift cylinders, etc., that will not impair additional testing of the existing machine.

Jan 1, 1983

By J. R. Thoenen

The enormous and constantly increasing demand for limestone to supply a multitude of uses is a remarkable feature of the mineral industries. As approximately 130,000,000 tons of limestone are produced annually, it is not surprising that deposits at or near the surface are gradually being exhausted and that less advantageous supplies are being worked. Quarries are becoming deeper and wider year by year, and in many places the volume of overburden that must be removed to allow open-pit work has increased alarmingly. Quarrymen are also gradually learning how expensive it is to sort and clean stone from a deposit overlain by poor material. As such conditions confront the limestone industry, the natural tendency is to seek some modification in method whereby the handicaps of increasing cost may be met and overcome. Operators, some of them unwillingly, have been forced to conclude that underground work in drifts and tunnels is the most logical solution of the problem. The unwillingness of some is largely due to unfamiliarity with mining and to the unfounded fear that costs must increase and dangers multiply when mining is undertaken.

Jan 1, 1926

By Stephen W. Lambert

The Bureau of Mines examined the wellbore of a vertical gas drainage well in the Mary Lee coalbed to determine the results of specific completion procedures in coal. A jet-slotting tool was used to cut four vertical slots through the casing about 1 ft below the coalbed. Even though stimulation treatment pressure was excessive, hydraulically induced channels were contained entirely within the target coal zone. Sand-filled, induced channels were horizontal, inclined, and vertical, and were propagated in directions similar to bedding planes, rock joint, and coal cleat directions measured in the mine. Variable gas flow rates, recorded during the productive life of the well, were attributed to chronic downhole pump malfunction and the slotted casing below the production zone.

Jan 1, 1978

To mine uraniferous sand-stone in an economically feasible and environmentally compatible manner without placing men underground. Approach Uraniferous sand is remotely extracted through a single borehole by cutting Into the are around the borehole with a high pressure water Jet, and pumping the resulting slurry to the surface. How It Works A 16-inch-diameter borehole Is drilled from the surface down into the burled mineral deposit, and the mining tool Is installed. High pressure water Is released as a jet from a nozzle In the mining tool to erode the are, forming a slurry that flows to the bottom of the cavity. The slurry Is drawn Into Inlets located near the bottom of the drill string. See drawing. After being pumped to the surface, the slurry is weighed, metered, and checked for radioactivity. It is then deposited Into one of a pair of sumps. Water collecting in the sumps drains Into an adjoining pond for reuse. Thickened are In the sumps is removed and placed In piles.

Jan 1, 1978

By Thomas M. Barczak, David P. Conover

Longwall shields provide essential ground control in longwall mining, yet a high percentage of shields are operating at less than peak capacity and many at well below the rated support capacity due to defective hydraulic cylinders or malfunctions in other hydraulic components. Leg pressure data are currently collected on state-of-the-art longwall shields, but typically are not analyzed to evaluate shield performance. The National Institute for Occupational Safety and Health (NIOSH) Shield Hydraulics Inspection and Evaluation of Leg Data (SHIELD) program is a Visual Basic software system that is designed to analyze leg pressure data and identify shields that are not performing to rated specifications. The program analysis is configured to detect the following conditions: (1) loss of leg pressure, (2) imbalance in leg pressure, (3) low set pressure, (4) low yield pressure, and (5) full extension of the bottom stage. Other performance assessment measures include the percentage of the support capacity utilized (ratio of peak load to yield load), the percent of time that a shield operates at yield load, the ratio of the set load to the yield load, and the amount of support capacity that is lost due to leaking cylinders. Historical record keeping will allow the user to select a particular shield and review the performance record as developed by the program for that shield. In addition to these performance assessment measures, the software will include an animated description of shield hydraulic systems that will describe the operation and significance of each hydraulic component and the impact of component failures on the shield’s capability to provide the required roof support. A general overview of the SHIELD program is provided in the paper together with an example analysis of a 2.5-year-old Australian longwall face.

By R. E. Hershey

1. Reserves were estimated for three coal beds: Lantana, Sewanee, and Richland. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated at 34 million short tons as of Januray 1, 1954. Of this total, 15 million short tons represents coal 28 inches and more thick. Areas in the beds were omitted from the estimate because available data relative to the bed characteristics were insufficient to permit making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves determined by this investigation.

Jan 1, 1956

By Mark P. Zaitsoff

The project involved design, construction, and testing of hydraulic models of culverts, decant and open channel spillways which are typical drainage structures used for protecting mine waste embankments. MSHA (The Mine Safety and Health Administration, U. S. Department of Labor) made a motion picture of the tests. Tests results and products in the forms of graphs, tables and films, demonstrate the principles and factors which govern the function and performance of the three types of drainage structures.

Jan 1, 1981

The development of an onboard contaminant diagnostic monitor to continuously measure contaminant level in a mining machine was advanced to a prototype stage in this contract. Several concepts were investigated and it was found that a static spool type sensor was the most reliable and accurate. Laboratory and field tests showed that an instrument based on this concept is capable of measuring contaminant levels and/or size distribution, depending on the configuration of the sensor. Moreover, this instrument can function on emulsions or homogeneous fluids. Current laboratory equipment can operate on homogeneous fluids only.

Jan 1, 1983

By James C. Duchon

The use of extended workdays (regular shift lengths of 10 or 12 h (hour), while still maintaining a 4O-h workweek) in mining operations is attracting growing interest in the United States. There is very little doubt that extended workdays is a very popular alternative among the work force because of the significant increase in days off, including weekends, especially when compared with traditional rotation schedules of working seven straight shifts or having only one weekend off every 4 to 6 weeks. However, there are some serious concerns by management, workers, unions, and various governmental policymakers that working 10-or 12-h days may create an added risk of accidents and health problems. The U.S. Bureau of Mines reviewed the literature studies related to the safety and performance issues of extended workdays. This report presents a summary of those findings. The studies examined in this review are divided into three sections: (1) laboratory, (2) field, and (3) accident and injury analysis. In general, results are inconclusive. Studies have shown both positive and negative effects. It is concluded, therefore, that in industries such as mining where accidents are a serious concern, special measures and evaluation in the use of extended workdays be considered.

Jan 1, 1994

By Michael E. Meadows

The results of tests to determine the .regional applicability of four synthetic unit hydrograph models are presented. The SCS curvilinear (Haan), SCS single triangle, Williams and TVA double triangle unit hydrograph models were tested on 271 events from 38 USDA experimental watersheds in 14 physiographic provinces. Though inconclusive due to the limited number of events analyzed, the results indicated a regional tendency for each model, with the SCS curvilinear unit hydrograph method generally performing best overall. It outperformed the SCS single triangle by predicting better shape; they differed less than 2 percent in time of peak and peak rate predictions. The Williams model performed well at Oxford, Mississippi and Coshocton, Ohio, which suggests it may be applicable to surface mined lands within the Northern and Central Appalachian Plateau and Texas coal producing regions. The TVA model is applicable to the Appalachian Plateau, specifically the Cumberland Plateau. A second test using only the SCS curvilinear unit hydrograph on 11 small watersheds and 50 events was conducted to investigate the effect of the excesss rainfall pattern on simulation results. A Green and Ampt infiltration model was coupled with the SCS unit hydrograph model to determine if peak rate and timing errors noted in the regional test could be minimized with an alternate to the SCS curve number model for determining infiltration losses. The results confirm the curve number model is the better approach to determining the excess rainfall pattern for unit hydrograph simulation.

Jan 1, 1983

By Pakalnis Rimas, Lyndon Clark, Tom Brady

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate data on weak rock masses into existing design relationships, with an emphasis on updating the span design curve for manned entries and the overbreak curve for longhole entries. Both curves were originally developed at the University of British Columbia, Vancouver, BC. The original database has been augmented by information from mines throughout the United States, Canada, Australia, and Europe. The common factor in all these mines is the presence of a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be stabilized so that the mineral-bearing rock can be extracted safety. The current NIOSH research attempts to provide rock mechanics tools to assist a mine operator in making economic decisions that will also ensure a safe working environment. This paper documents the Nevada database with a special emphasis on Nevada underground gold mines.

By William A. Beck

Bauxite was discovered in the Springvale district in 1916. About 16, 000 tons was mined in the period 1916 to 1922, but no bauxite mining has been done since that time. The Bureau of Mines explored for bauxite in the district from September 5 to November 18, 1943. During the life of the project, the Bureau of Mines obtained mineral exploration agreements covering a total of 11,330 acres from 50 property owners. A total of 388 holes were drilled on five of these properties and 164 samples were taken and analyzed. The Springvale bauxite district includes an area of about 30 square miles in the northwestern part of Randolph County, Ga. The village of Springvale is in the west central part of the district, and Cuthbert is 8 miles southeast of it (fig. 1).

Jan 1, 1949

By James M. Spear

Sample results suggest the only mineral resources in the study areas are placer gold deposits along the South Fork Kern River in the Woodpecker RARE II unit (fig. 1). These deposits, in Rockhouse Basin, total 4.5 Figure 1.--NEAR HERE. million cu yds (3.4 million cu m) of indicated subeconomic gold resources in four deposits of "older" gravel. Gold value in samples averages $0.36 per cu yd ($0.47 par cu m) and is as much as $4.44 per cu yd 1/. Cost of mining the gravel and recovering the placer gold is estimated to be more than $2 per cu yd ($2.62 per cu m) for a deposit of this size and type. Additional inferred subeconomic placer gold resources with similar grade probably occur in four other deposits of "older" gravel on which no mining claims were located. Placer gold occurrences on upper Trout Creek contain gold worth as much as $4.50 per cu yd ($5.88 per cu m) 1/. Average grade is much lower, and only about 1,000 cu yds remain (760 cu m). These occurrences do not constitute a resource, but may attract hobbyists not dependent upon making a profit.

Jan 1, 1982