Search Documents

By Anne Lemnitzer

Full-Scale cyclic field testing was performed on a 3x3 pile group consisting of nine cast-in-drilled-hole (CIDH) reinforced concrete shafts and a comparable single-shaft in order to investigate group interaction effects, derive p-y curves for reinforced concrete fixed head piles and to validate currently available p-multiplier models. The piles are identical in diameter of d=2 ft and were tested in similar soil conditions. The single pile as well as in three piles within the pile group were instrumented with internal sensor instrumentation to record pile curvatures. External instrumentation was used to control and measure the lateral displacement of the specimens. Experimental studies were supported with analytical models to enable comparisons and offer design recommendations. All test specimens were tested to structural failure and group interaction factors ranged between 0.8 at small displacement levels and increased towards unit near structural failure. A set of p-multipliers was found to reproduce an accurate fit to the available test data.

Jan 1, 2010

By Dhanvin B. Mehta

Pile testing is generally understood as static load test. It is our common experience that for high capacity, large diameter bored piles, static testing is expensive and time consuming. It is practically impossible to test large number of piles by traditional testing methods. The escalating cost in carrying out a static load test, as well as incomplete information derived therefrom compelled researchers in United States to look for an alternative method of testing for both bored and driven piles. The original research work was carried out at Case Western Reserve University in early 70's, under the funding of Federal Highway Administration as well as several State Depts. of transportation in United States. The outcome of the research was the development of a state of art field computer for capacity determination, based onOne Dimensional Wave Mechanics.

Jan 1, 1996

By Arvindh Gupta

BC Hydro proposed to improve the stability of the existing Seven Mile Dam with 54 corrosion protected, re-stressable anchors comprising 92/0.6? strands each, in phase 2 of the program. Being globally the largest capacity anchors ever build, coupled with extra ordinary specifications, the project was a challenge for the entire post tensioning industry. The paper discusses the challenges associated with the anchor material supply as per specifications, extensive research and development carried out by Con-Tech Systems ltd. to overcome the challenges and contribute in making the project a success. The substance of this article is published in the Aug/Sep issue of ADSC magazine.

Jan 1, 2004

By Jeffrey A. Gebhard

As part of the design and construction of the new St. Anthony Falls I-35W Bridge, a full-scale load test was conducted on a 6 1/2-foot diameter drilled shaft in the St. Peter Sandstone. This load test helped identify shaft-rock interaction properties, including end bearing and multiple zones of differing shaft resistance for design of the drilled shafts beneath the three piers adjacent the river. The load test was designed by Load Test, Inc., Braun Intertec and the design team of Figg Bridge Engineers/TKDA and constructed by Design Build Consortium of Flatiron/Manson. Oversight was provided by the Minnesota Department of Transportation. Based on these test results, the drilled shafts supporting the St. Anthony Falls I-35W Bridge were designed to reduce risk and maximize economy for the people of the State of Minnesota.

Jan 1, 2009

By William Siegel

Kleinfelder provided foundation analysis and design for an expansion to a cement plant in Florence, Colorado. The expansion was a conversion from a horizontal wet process to a vertical dry process, and resulted in the construction of a number of structures with heavy foundation loads. [ ] The field investigation identified old fill and saturated sands and gravels above a shale/limestone bedrock environment. Based upon the anticipated loading, drilled piers socketed into bedrock were recommended. The structures were constructed in accordance with the design recommendations.

Jan 1, 2007

By X. L. Chen

The diaphragm walling has been recently adopted in one of the largest excavation of deep foundation engineerings in Shanghai, China with dimension of 90m in length, 50m in width and 13m in depth to solve its stability problem. In this paper the field test for monitoring the stability of the diaphragm wall is discribed, in which the excess pore water pressure and the horizontal displacement of the clay layers were monitored during the period of the excavation. The data measured in the field test are efficient for the safety during construction.

Jan 1, 2010

By Pier Luigi Iovino

As Technical Director of the Naples, Italy based Fondedile, a geotechnical construction firm specializing in static restoration of structures, Fernando Lizzi, Ing., devoted over 30 years to the pursuit and advancement of static restoration and subsoil strengthening. Seismic events, construction of new structures on polluted and/or unstable soils in urban areas, and a need to carefully preserve and restore delicate, war-damaged historical structures, manifested the need for underpinning projects. Traditional construction methods and approaches, such as underpinning with additional foundation masonry, were not suitable and would have further jeopardized the stability of the structures. The introduction of the palo radice (root pile) revolutionized the field of underpinning. At the time of the first application of micropiles, the industry standard was driven piles. The drilled micropile was conceived and first implemented in the early 1950s, as an innovative means to underpin sensitive, historic structures and structures in urban areas. Specifically, the new construction technique was conceived as a less expensive alternative, designed to accept structural loads, be installed in limited access areas, in varied working and sub-surface conditions, which did not involve changing soil characteristics, and had minimal disturbance to the structure being underpinned, or to adjacent structures.

Jan 1, 2003

By B. Francis

Literature provides only limited information regarding the behaviour of laterally loaded piles socketed into weak rock masses. A laboratory program, comprising a number of tests of scaled models of the pile/rock mass system has been conducted. A synthetic rock, known as Johnstone was used to simulate a naturally weathered and fractured siltstone. The load-deflection behaviour of the test piles was measured, and strain gauges were fixed to the model piles to assess the bending moments. The laboratory results are compared with the results from several theoretical models, some of which are in the form of commercial software packages. This study highlights the inadequacy of existing methods to adequately model the influence of rock joint orientation in geotechnical design. Additionally, numerical modelling of the pile/rock mass system was carried out using the discrete element program UDEC. The importance in modelling the system using discontinuum mechanics is highlighted, particularly to capture the anisotropy of the rock mass.

Jan 1, 2004

By J. W. Slatter

Cast in situ screw piling techniques (both displacement and non displacement) have seen considerable growth in recent years due to competitive production rates, low noise and vibration free installation. However the discussion on the mechanics of auger installation, which has implications on the installation effects and installation forces of screw piling augers, has been almost exclusively targeted towards non displacement techniques and in particular continuous flight augers (CFA). This paper discusses the historical development of the understanding of screw piling auger mechanics in sands and presents a new theoretical model to predict the soil transport and displacement characteristics of both displacement and non displacement augers with variable geometry.

Jan 1, 2000

By Emad Farouz

This paper compares the predicted axial capacity of driven Pre-cast Pre-stressed Concrete (PPC) piles for the Lake Gaston Water Treatment Plant (LGWTP) using several design methodologies versus the axial capacity measured from dynamic and static load testing. The LGWTP site is located in Chesapeake, Virginia and is part of the Great Dismal Swamp. The subsurface investigation included soil borings, in-situ dilatometer (DMT) tests, and in-situ piezocone (CPTu) tests. The axial capacity predictions of the PPC piles were performed using the computer programs DRIVEN and FB-DEEP which are based on SPT N-values. Additionally, an empirical method proposed by Martin, et al. (1987) based on local experience with PPC pile design in the Yorktown formation in the Tidewater area of Virginia was also evaluated. Finally, the ?Laboratoire Central des Ponts et Chausées (LCPC)? method developed by Bustamante and Gianeselli (1982) based on CPT measurements was also used to develop the axial pile capacity of the piles. This paper shows that the FB-DEEP computer program and the LCPC method provided a reasonably good prediction of the pile axial capacity measured from PDA, CAPWAP, and Static Load Tests in comparison with the other design methods used. The soils in this area develop significant setup over time and it was found that FB-DEEP and the LCPC method are capable of incorporating this setup in the prediction of the long-term axial capacity of driven piles in this area.

Jan 1, 2007

By Ronnie W. Sisk

1. Troubles start early - Inadequate Geotechnical Data A. Owners think they are saving money by allowing limited soil borings at their site. This places a high gamble on the bidders and the Lump Sum Price will be higher. B. Inaccurate elevations on soil reports. a. Surprises in depths - over or under design bid bottom elevations. 1. Requires backfill and extraction of casing that is too short for the greater depth of the drilled shaft. 2. Redrill utilizing longer casings. 3. Softer earth (backfill) can cause difficulties in redrilling such as less quantity extracted on the auger and maintaining plumbness. 4. Greater concrete overrun. b. Extreme under depths. 1. Excessive concrete is placed as a result of planning for a deeper shaft. c. Geotechnical report that does not supply a layout of boring locations. d. Design Engineer does not have a basic knowledge of how a caisson is installed.

Jan 1, 1988

By Maurice Bottiau

When dealing with displacement auger piling, some general and fundamental issues have to be considered, irrespective of the system. More than with other pile types, the interplay between the soil conditions and the design and execution is of outstanding importance. This paper intends to address these issues and to summarize some critical matters in terms of design, execution and control such as : ? Importance of a reliable soil investigation ; ? Summary of the design as it is addressed in Europe for this category of piles ; ? Criteria for a good choice and control of the correct asset of the piles ; ? Importance of the concreting phase; ? Relation between the power and the engine characteristics of the drilling equipment with the final bearing capacity. For each of these issues detailed examples will be given as well as results of load tests and in-situ control during execution.

Jan 1, 2003

By Martina Balic

Dynamic properties of the drilled shaft foundations supporting Doremus Avenue Bridge were determined by forced vibration testing. The main objectives of the substructure testing at Doremus Avenue Bridge were: (1) site evaluation with respect to the dynamic soil properties, and, (2) shaft evaluation for the purpose of definition of their dynamic stiffness. The site characterization entailed crosshole testing for the purpose of evaluation of the shear modulus profile. The drilled shaft impedance evaluation was done through forced excitation using an electromagnetic shaker. The responses of the tested shaft, as well as the response of adjacent shafts, were measured for the purpose of evaluation of the shaft interaction. To gain a better insight into the shaft dynamics, one of the shafts was instrumented with five triaxial geophones distributed along the full length of the shaft. The scope and results of the site characterization, shaft impedance and shaft interaction evaluation are presented.

Jan 1, 2004

By Anne Fagot

Because of the risk of corrosion caused by stray currents, steel foundations and steel sheet piling are generally prohibited in the vicinity of railway structures. Steel solutions are only accepted if they are shown to meet the required design working life and if this can be achieved at an acceptable cost compared to competing materials. The influence of stray currents on various steel sheet piling designs was studied using software initially dedicated to gas and pipeline industries and cathodic protection systems. It has been successfully adapted to model stray currents affecting steel sheet piling. Corrosion rates assessed using this modeling software were considerably lower than commonly expected. Zones of potential corrosion risk were identified; specific cost-effective countermeasures could be established. The developed software tool can help to optimize the design of piling solutions in the vicinity of DC railway power systems in terms of suitable countermeasures that meet structural reliability and cost requirements.

Jan 1, 2008

By N. V. Nayak

Konkan Railway Project is one of the most ambitious railway construction projects in India, involving construction of a 760.km long, Broad Gauge (1676 mm), single track railway line, connecting Roha in Maharashtra State with Mangalore in Kamataka State. The railway line travels along the Western Coast of Indian subcontinent, through states of Maharashtra (382 km), Goa (105 km) and Karnataka (273 km) (Fig.1). The project alignment traverses through one of the most formidable terrains ever encountered, in the history of railway construction in India. In the State of Goa only, railway alignment is crossing 6 major rivers Terekhol, Chapora, Mandovi, Zuari, Sal and Talpona. Zuari Railway Bridge (1305.6 m), Mandovi Railway Bridges (I and II) (1182.7 m) rank as 2nd and 3rd long bridges, (first longest bridge being Sharavati Bridge (2.2 km} at Honavar) which have been constructed on Konkan Railway. All these three bridges have been constructed by M/s.Asia Foundations and Constructions Ltd. (AFCONS). This paper presents, case history of construction of pile/caisson foundations for Zuari and Mandovi Bridges.

Jan 1, 1996

By K. S. Ho

With the aid of the advanced electronic devices and micro-processors, the quality control of deep foundations can be carried out by Non-Destructive Tests (NDT). Three methods are presented here: the Sonic Logging, Vibration and Stress Wave Analysis Methods. The principles, equipments used, testing procedures and applications are fully described. The correlation of these methods with the conventional tests (mechanical coring and loading test) are studied to give a better understanding of the methods. Several case histories with the test results obtained from a number of sites in Hong Kong and overseas are discussed to show how the pile quality can be examined and especially, how to confirm the effectiveness of remedial works on a defective pile. Recommendation on the percentage of piles to be tested are given at the end of the paper by using statistical method.

Jan 1, 2010

By Leonardo Massone

The p-y method is one of the most popular methods in pile design and has been calibrated for various boundary conditions using numerical and experimental studies during recent years. Most studies on reinforced concrete (RC) piles have included the impact of flexural nonlinearity, (e.g. nonlinear moment?curvature relations) but not considered associated pile shear deformations when deriving p-y curves from field data. Common p-y curves may be better applicable for piles with flexure dominated failures (e.g. piles with free- head boundary conditions). For piles with fixed head boundaries (i.e. rotation restrained piles) shear deformations could be of significant influence. To study this problem, a coupled shear flexure interaction model for axial-bending-shear behavior coded in OpenSees is applied to a 0.61 m flagpole and a 0.61m fixed head pile specimen to investigate the possible influence of shear deformations to the overall pile responses. The surrounding soil is represented by p-y curves derived from prior large scale testing on piles with similar boundary conditions. Analysis results show that for flagpole piles, shear forces and shear deformations were insignificant. Considerable contributions of pile shear displacements and forces were observed for the fixed head pile, with shear displacements contributing up to 40% of the total pile displacement. Results suggest that nonlinear shear deformations for reinforced concrete piles should be considered for fixed-head or similar conditions, and that currently used p-y curves may underestimate the actual lateral pile displacement and possibly lead to unsafe design for the particular boundary condition.

Jan 1, 2011

By Donald A. Deardorff

The capacity of a helical pile can be determined analytically using the individual bearing or cylindrical shear methods which are dependent on soil strength parameters and helical bearing area. The torque correlation method is widely used in the helical industry to determine the capacity during installation by monitoring torque during the final seating of the helicals. This method has been shown to be a better predictor of strength than the individual bearing or cylindrical shear methods. To determine capacity using the torque correlation method, the final average installation torque (ft-lbs) is multiplied by an empirical torque correlation factor (Kt, ft-1). Kt values have been well documented for square bar shaft helical products and can vary from about 3 to 20 ft-1 depending on pile geometry and soil type. A default value of 10 ft-1 is generally used for all square shaft sizes and soil conditions. Less research has been done on determination of Kt for round pipe shaft helical products. Studies have indicated that factors which affect Kt include soil type/strength, number of helical plates, helix spacing, helix pitch, depth of embedment, downward pressure (crowd), shaft diameter (round pipe) and load application direction while other studies have discounted some of these factors as inconsequential. This paper reviews past research findings regarding Kt determination for square and round pipe shaft helical products and presents a case history of round shaft helical pile installations in Chicago clay which resulted in much lower than expected Kt values.

Jan 1, 2007

By Daniel Levacher

Pile load tests in site require extensive means of action and time. To get outstanding tests, the environmental test conditions must be perfectly known and acceptable. They concern the support installation, the loading, the access and instrumentation site conditions and the economical aspects. In particular cases as offshore areas, the load tests are not feasible. Moreover the variability of soil characteristics limits the interpretation results at the considered tested site. The use of centrifuge modellling offers an other way to study the loaded pile behaviours. Centrifuge tests lead to parametric approaches which constitute for geotechnical engineers an important data base tor recommendations and design codes. To accurately simulate pile behaviours by checking similitude laws linked to the studied problems, the installation of model-piles must be also representative of the in-situ piles. Driven piles account for a large part of the piles installed through the world, mainly for offshore or harbour constructions. So, to explore driven pile problems by centrifuge tests, miniature pile driving hammers must be developed and tested under macro-gravities. The paper describes two types of these ones in details. They are commonly used at the centrifuge centre of the Laboratoire Central des Ponts et Chaussées - (LCPC) - [Réf. 1] for different deep foundations researches. Performances and limitations are given for both miniature pile drivers and some results from their use are presented to illustrate the suitability of these apparatus.

Jan 1, 1996

By David C. Kraft

Atlas Systems, Inc. (ASI) resistance type piers were used to underpin a 100 year old historic structure at Fort Monroe, Virginia. This 3-story structure with basement was underpinned with 155 steel tubular push piers (4" OD) that were hydraulically installed to depths ranging between 90 and 110 ft. and to installing forces in excess of 60,000 lb. Project requirements included lowering the basement floor by 1-1/2 ft. and constructing new footings and adding stem walls to connect to the existing masonry walls. Additionally, the underpinning piers were temporary which required the development of a decoupling system to permit the transfer of the building loads from the underpinning piers to the new footings. The structural loads at the foundation level required a c. to c. pier spacing of 3.75 ft. in order to meet project requirements of a minimum Factor of Safety of 3.0 on the pier load capacity. Project requirements included a load test on the selected underpinning pier (ASI - AP2 4000.219) in order to establish installation depths for seating the piers to 60,000 lb. The project was successful in supporting the full load of the structure during the construction phase. Considerable savings in time and cost were achieved as well as avoiding any vibrations or noise during installation of the piers.

Jan 1, 2002