Search Documents

By G. Stuart Littlejohn

In spite of recent concerns in certain European countries, I believe that silicate-ester grouts will continue to be employed in practice, unless more cost-effective inorganic grouts are developed for the treatment of fine sands. It is also noteworthy that over the past 40 years, there has been a record of good experience where silicate-ester grouts have been used in ground improvement. Nevertheless, there is now a need via the European Standard EN 12715 (2000) "to assess the environmental impact, particularly the toxicity of the grout and grout components, and their effect on ground and drinking water should be considered before grouting." "When testing the grouting material for environmental impact, the following aspects should be considered: ? Whether during processing, transport or grouting, substance can be generated or released which could be hazardous to the environment or the grouting crew; ? Whether noxious substances can spread upon mixing with ground water; ? Whether reaction products can be produced or released which influence the water quality; ? The type of particles eroded from hardened grout; ? Chemical reactions between hardened grout and the ground water."

Feb 10, 2003

By Joe Harris

Large structures, such as a multistory office building or a large storage tank, are constructed the most economical way possible, which may involve a shallow foundation system placed on native soil or compacted fill material. Over the life of the structure, the foundation system may not perform as originally anticipated, leading to differential settlement. Minor differ- ential settlement is expected; however, settlement that exceeds allotted tolerance can render the structure inoperable. Compaction grouting is a well-known and accepted ground improvement technique that can be used to not only stabilize but relevel multistory buildings and large dia- meter storage tanks. Two projects, each with differing types of structures, were successfully remediated utilizing com- paction grouting as the primary method to remedy settlement.

Sep 1, 2023

By Stefan Dahlin

The laboratory tests indicated low permeability but as I said, as a rule, the permeability in the field has been found to be higher. A high permeability has also been found when doing back calculations of rates of settlements in different cases. But as I also said, there's a need for further studies in this area.

Feb 10, 2003

By Don W. Dotson

In 1962, Kondner prepared several papers dealing with hyperbolic stress-strain response of cohesive soils. The following year, Brinch Hansen proposed 80% and 90% failure criteria for stress-strain behavior of cohesive soils. Fellenius was instrumental in popularizing these failure criteria for pile load tests and offered a direct solution equation for the failure load according to the 80% failure criterion. Since the 90% Criterion has been incorporated into the International Building Code, equations for the direct solution of the failure load at the 90% Criterion would be useful to practicing engineers. This Technical Note supplies the derivation methodology for the 80% Criterion and provides expressions to determine the load and deflection at failure for the 90% Criterion.

Aug 1, 2013

By Ali S. Fayad

"In June 2014, Orange County Flood Control District (OCFCD) completed construction improvements of the East Garden Grove-Wintersburg Channel for a price of $42 million. Instead of the pre-existing traditional trapezoidal levee, the channel was improved with a vertical compact levee. Dubbed Soil-Mix-Sandwich (SMS), this geo-structural and environmental solution for coastal channel improvements, underlain by liquefiable soil strata, was both a design and construction innovation. It employed Deep Soil Cement Mixing (DSCM) within the confines of a hydraulically-pressed (Giken Method) sheet pile duo. SMS was unique because it incorporated both subterranean and supra-dredge-line soil mixing within a very narrow workspace. Its DSCM pattern aimed at optimum densification of the workspace and was confirmed during the construction process. It availed the DSCM sub-contractor (Hayward Baker Inc.) the opportunity to demonstrate the fitness of their huge wet-mixing machinery within a very confined access-area and introduced approximately 70,000 cubic yards of DSCM within a limited 15 foot workspace width that stretched for a mile. The sheet pile duo created a construction-enclosure that became a stay-in-place load resisting system. PROJECT CHRONOLOGY AND LOCATIONAn Orange County Flood Control District (OCFCD) project-report was commissioned to study the East Garden Grove Wintersburg channel (OCFCD facility # C05). The report examined the hydraulic conveyance of the C05 channel and was concluded in 1994 by Williamson & Schmidt. The project-report did not encompass extensive geologic studies; but it provided several alternatives for channel improvement. It recommended a single row of sheet piles as the preferred alternative for the downstream reach.The most downstream reach of the C05 channel is located in an environmentally sensitive area, in City of Huntington Beach, California, USA. Its site includes seismic chasms that surface within the C05-footprint (the Newport- Inglewood tectonic fault). Extensive deposits of liquefiable soil exist beneath the channel. Furthermore, tidal-influence prevails against the channel levee. Implementation of a successful design for channel improvement emerged after several traditional concepts were deemed unacceptable by geotechnical consultants. OC Public Works (on behalf of OCFCD) was in need of a design and construction technique that mitigated many associated risks. From these circumstances, Soil-Mix-Sandwich was born and was referred to in the rest of this discussion as SMS. OC Public Works required the SMS design concept to undergo verification by independent geotechnical consultants. SMS chronology from conception to construction can be summarized as follows:"

Jan 1, 2015

By Piotr Kozlowski, Stanley L. Worst, Matthew J. Niermann

The Waterman Hospital in Tavares, Florida was undergoing an expansion and required a below-grade excavation immediately adjacent to the Emergency Department. This wing of the hospital was under high traffic and required uninterrupted access for ambulances as well as helicopter landings. The below-grade expansion was also next to a part of the hospital which did not have a basement. Tiedback soldier beams and wood lagging were used as the earth retention system where the shoring line was not immediately adjacent to the existing structure. Structural jet grout underpinning was used to support the existing building and to serve as the earth retention system in the more sensitive area. Jet grout underpinning was chosen to minimize movements, loss of ground and settlement of the structure which was bearing on clean sand deposits. This paper will discuss the design, quality control and construction of jet grouting and its application to this project. INTRODUCTION Project Background The expansion of the Waterman Hospital included an addition to the Emergency Department. This addition was located adjacent to the existing hospital building in a congested area with limited access. The north side of the addition was bordered by the ambulance drop-off area. The south side of the addition was bordered by the helipad landing area. Both areas had to remain open and fully accessible 24 hours a day, 7 days a week.

Jan 1, 2019

By David J. Puller

As part of the value engineering process on a major Design Build highway project, instrumented trial pile load tests were used to achieve savings in cost and time on the foundations for a major river crossing. Two trial piles were tested close to failure load at 25MN. Following the interpretation of the pile load test results which included the determination of the ultimate shaft and base capacity, the mobilisation of the shaft and base resistance with pile displacement, and correlations with vertical effective stress and SPT profile, a revised design methodology was proposed. A 25% enhancement on commonly assumed ultimate shaft friction in Chalk was adopted. In addition a significant reduction in the Factor of Safety on end-bearing capacity generally used was also implemented. The revised design resulted in a significant cost and time saving on the piling operation with the pile length reduced by up to 6m (approx. 20%) for the river piers.

Jan 1, 2002

By Sam Messina

[Project: Job Number: Date: Superintendent: Person Making Inspection: Note: The following checklist shall be used on a regular basis as an overall assessment of the jobsite. The checklist is not all-inclusive. All applicable Federal, State, and local regulations, standards, and ordinances pertinent to the jobsite conditions must be evaluated on a continuous basis. Column A - Adequate Column I ? Inadequate]

Jan 1, 1998

By L. Z. Xie

The results of the experimental study on the static behavior of single piles subjected to repeated and reciprocating axial loadings are recommended in this paper. Tests of four full-scale single piles of two different lengths under repeated loading and those under reciprocating loading have been conducted using the slow maintained load test method. All the eight piles were instrumented with strain gages located along the shafts. The study showed that for repeated loads below a certain critical value the total displacement of the pile top approached gradually a constant value. However, any repeated load greater than the critical value resulted a residual displacement per cycle, and that the reciprocating load capacity of a pile was dependent on the ultimate bearing capacity of the pile in tension and both were in the direct ratio.

Jan 1, 2010

By Jianhua Wang, Jianming Yao, Zhen Meng, Jinjian Chen

"Drilled screw pile is a newly developed displacement pile foundation which has been applied in soft clay for many years. Compared with traditional circular displacement pile, It is characterized by high bearing capacity, small volume and small squeezing effects. For the purpose of investigating the squeezing effects of drilled screw pile, a full scale field monitoring test with two test piles was performed. Detailed soil horizontal displacement and pore pressure measurements were conducted in the vicinity of the two drilled screw piles during penetration and subsequent soil consolidation. It can be concluded that the horizontal displacement of the surrounding soil induced by the installation of a drilled screw pile is mainly in a circular region with a diameter of 3 m (r/D<6), and the compaction effect outside the area can be essentially negligible; The excess pore pressures measured at the same time increase with depth throughout the entire process of consolidation, and its dissipation shows an exponential decay as a function of time.INTRODUCTIONA knowledge of the displacement and stress changes induced in the soil surrounding a pile is very important for evaluating pile performance. Numerous field and laboratory research projects have examined loading conditions, total soil stresses, and excess pore pressures during and following pile installation (Pestana et al., 2002). A relatively comprehensive and detailed review of these experimental works from 1948 to 2002 was presented by Pestana et al. (2002). More recently, Xu et al. (2006) conducted a field experiment to study displacements and stresses in the vicinity of two pipe piles during their installation in a soft lightly overconsolidated clay and compared the field measurements with existing predictive methods. Abdrabbo and Gaaver (2011) collected field observation data from four different construction sites to study soil disturbance during construction of piles using continuous flight auger (CFA). They have found that the disturbed zone of soil by CFA has a conical shape and the excess pore pressure has no appreciable influence on the load capacity of the piles.Drilled screw pile (DS pile) is a kind of vibration-free, cast-in-place concrete pile. Because of the excellent bearing performance, low level of vibration pollution and negligible spoil, as well as its fast construction speed, DS pile has been widely accepted by many engineers around the world. As a new type of drilled displacement pile, the significant installation effects of DS pile on the adjacent soil have not been systematically and integrally investigated yet. Since a proper numerical simulation of the real installation process of DS pile is difficult to achieve, the investigation based on field measurements is necessary. This paper presents a field investigation of the installation effects of two DS piles on surrounding soils. Detailed horizontal soil displacement and pore pressure measurements during pile installation and subsequent soil consolidation have been conducted. Based on the monitoring data, variation of horizontal displacements and dissipation of excess pore pressures with depth and time have been analyzed. What's more, the construction machinery and technology used in DS pile installation are also simply introduced."

Jan 1, 2015

By Seiji Mizutani, Hirofumi Taguchi, Makoto Yoshida, Hidenori Takahashi, Naotoshi Shinkawa, Kazuo Konishi, Yoshiyuki Morikawa, Masaya Kawata

"The lattice-shaped cement treatment method has been used to improve the seismic performance of liquefied sandy soil in Japan. The efficacy of the method has been confirmed by the huge earthquake in Japan. In the present study, a new method to improve sandy ground by using the lattice-shaped cement treatment method is proposed as a liquefaction countermeasure. It is the floating-type and lattice-shaped cement treatment method, where cement treated soil is not fixed to an un-liquefiable stratum. In this method, a fixed-type structure such as treated soil should be formed at the side of the floating-type treated soil to reduce its lateral displacement. In the study, one-dimensional dynamic response analyses were firstly conducted to confirm the mechanism of the new method. Secondly, a series of centrifuge model tests were performed to demonstrate the effect in a proto-type scale's stress condition. The analyses and model tests confirmed the effect of liquefaction countermeasure of the new method.INTRODUCTIONLiquefaction induced by an earthquake generates sand boiling and ground settlement. Other problems have also been reported, including a decrease in bearing capacity and an increase in the horizontal earth pressure against retaining walls. To prevent these problems caused by liquefaction of the ground, various countermeasures have been proposed, such as cement deep mixing and high-pressure jet mixing methods. These methods have the big advantage of being applicable to ground that contains soil with a fine-grain fraction. Furthermore, the unnecessary displacement caused by the construction can be reduced. In Japan, a lattice-shaped cement-treatment method has frequently been used at many construction sites to prevent liquefaction, where cement-treated piles are intersected to form a lattice, as shown in Fig. 1. The lattice-shaped walls can reduce the shear stress generated by an earthquake, restricting the liquefaction at that location. However, the construction cost of the cement treatment is relatively high compared to other methods such as the sand compaction pile (SCP) method, and needs to be reduced. Therefore, decreasing the total volume of the cement treatment is necessary to reduce the construction cost."

Jan 1, 2015

By Jim Bruce, Naresh Gurpersaud

"The West Toronto Diamond project, under construction since 2006 and due to be complete in 2015, is a rail-to-rail grade separation project in the heart of urban Toronto. Once complete, a depressed corridor over 1000 metres long will take the CN tracks beneath the CPR tracks. An interlocking steel pile wall serves to retain ground and cut off groundwater. Remedial measures, constructed using jet grouting, were required at several locations within and behind the steel piles.At mechanical interlock joints damaged or suspected of being damaged, jet grouting was used to improve native soils on the retained side of the wall to reduce permeability of the soil mass in intimate contact with the joints to 10-7 cm/s. At a number of steel piles where groundwater and soil type combined to cause basal instability inside the pipes during the interim between excavation and concreting, jet grouting was used to construct temporary bottom seals. At locations near adjacent structures where the steel pile installation process resulted in disturbed ground on the retained side of the wall, jet grouting was used to strengthen and stabilize ground.This paper outlines the details of the various jet grouting applications, the respective testing programs implemented to demonstrate in situ permeability and strength of the soil-grout matrix, and performance of the constructed system.INTRODUCTIONThe West Toronto Diamond (WTD) is a junction of several railway lines, all intersecting at the same grade (Figure 1). A major grade separation project at this site commenced in 2006 and is scheduled to be completed in 2015. The whole of the work is comprised of multiple contracts, completed and/or ongoing, by different constructors. Once completed, a depressed corridor over 1000 metres long with over 23,500 m2 (face area) of retained earth will bring the CN tracks beneath the CPR tracks and eliminate a major bottleneck at the most heavily used rail crossing in Canada."

Jan 1, 2017

By G. L. Sivakumar Babu, P. Chaithra

"Raft foundations which are used against differential settlements and for carrying heavy loads can still be subjected to excessive settlements even if it is safe against bearing capacity consideration. Providing additional piles under the raft can reduce such settlements to acceptable values. In addition to settlements, the piles also relieve the raft a part of the total load and thus the bearing capacity of the Combined piled raft foundation (CPRF) is improved. Parametric study of response of piled raft foundation has been conducted and the results have been presented. The study is conducted using finite element based software, PLAXIS 2D. The main objective of the paper is to evaluate the parameters that affect the performance of piled raft for an economical and effective design. It has been shown that piled rafts are an economical solution in foundation design compared to raft foundation, for the soil conditions considered in the paper.1. INTRODUCTIONThe aim during the design and construction process of high-rise building foundations in urban areas is to ensure the lifelong safety and serviceability of the new and existing buildings in the neighborhood. In order to realize this aim in a cost-optimized manner, the combined pile raft foundation (CPRF) was developed (Katzenbach et al., 2005). For the foundation of high rise buildings with good subsoil, the simplest structure considered is a raft. But when the subsoil near the ground surface has low load-bearing capacity, high-rise structures are often rested on piled foundations.A piled raft and pile group serves similar purposes, but there are essential differences between them. A pile group is a set of piles that have a pile cap. The piles would be designed to share the pile load at ultimate state. The pile cap would be designed to link the piles together but the contribution of the pile cap to bearing capacity will not be included in the design. On the other hand, a piled raft is a foundation, wherein piles are provided along with the raft so that the total load acting is shared partly by the raft and partly by piles, rather than being dominated by the piles (as in a pile group). Piled raft foundations utilize pile support for control of settlements with piles providing most of the stiffness at serviceability loads, and the raft element providing additional capacity at ultimate loading (Poulos, et al., 2011). Therefore, piles are included in a foundation for two main design purposes: to provide adequate bearing capacity and to bring down the settlements to an acceptable level."

Jan 1, 2015

By Amr M. Sallam

A case history of utilizing a mat foundation enhanced with ?settlement-control? piles to support a high-rise building in Downtown Orlando is presented. Original geotechnical engineering studies, performed by others, recommended pile foundations due to difficult soil conditions and highly variable loads. The value engineering study performed by the authors provided alternative foundation system of the mat foundation enhanced by ?settlement-control? piles. The alternative foundation system required few iterations of structural and geotechnical analysis. A target stiffness for the settlement-control piles was selected by the structural engineer. Pile load tests were performed to verify the recommended pile geometry. A total of 81 auger-cast-in-place settlement-control piles 45-foot long 16-inch diameter were installed. A total of 24 columns were monitored for settlement, which showed substantially less settlement than predicted. It is the authors? opinion that the ?settlement-control? piles increased the mat stiffness, relieved the concentration of contact pressures around heavily loaded columns, and reduced potential differential settlement. Mat foundation with settlement-control piles provided border-line foundation solution between shallow and deep foundations and has the potential to be widely used in Central Florida for similar subsoil and loading conditions; however a thorough analysis using three dimensional Finite Element Modeling may be needed to refine the geotechnical evaluations.

Jan 1, 2009

By Emre Turk, Suat Gullu, Candan Gokceoglu, Ahmet Sirri, Asli Can

In this study, the ground improvement application applied under the live railway bridge's approach embankments in Sivas, Türkiye was investigated as a case study. The soil profile is mainly composed of orangish conglomerate, clay, silty sandy clay, and under claystone, and mudstone units in the study area. As a soil improvement method, the Deep Soil Mixing (DSM) technique based on the principle of simultaneous mixing the ground while injecting with the water-cement mix, was selected. The application of DSM columns is designed to be 45 degrees horizontal, in order to reach the deepest point of the soft clay units for better improvement against settlement. The core samples were taken from the DSM columns and the compressive strength tests were performed in the laboratory. The results were higher than the minimum designed values. It means that inclined DSM columns were applied successfully, and the excessive settlement problem was solved.

Oct 1, 2022

By Richard E. Sylwester

Evaluating surface and subsurface conditions for marine foundations (bridges, causeways, terminals, etc.) is often done with a limited amount of data. Subsurface information for these projects is primarily acquired using traditional methods, such as boreholes, test pits or divers, which tend to be expensive and limited in the area of coverage. A number of geophysical methods, including precision bathymetry, sidescan sonar, and seismic reflection or subbottom profiling are extremely cost-effective and obtain significantly more data than can be acquired using traditional intrusive methods. These geophysical methods provide detailed surface images and continuous profiles of the subsurface stratigraphy. This information can be invaluable for selecting the best location for geotechnical boreholes and to map potential geohazards such as submarine slides and filled or open scour holes. Offshore investigations conducted for a proposed highway bridge (Knik Arm Bridge, Cook Inlet, AK), the retrofit of two existing bridge (Antioch and Dumbarton Bridges, CA) and a proposed cruise ship terminal (Ketchikan, AK) used a combination of geophysical methods to map water depth, detect and map debris on the seabed, map the thickness of unconsolidated sediment, determine the depth to bedrock and identify potential geohazards such as scour holes. The results of the geophysical investigations will be used to select locations for obtaining geotechnical borings, to extrapolate geologic information between existing or proposed boreholes, evaluate the potential depth of scour and design a pile support pier. Geotechnical engineers, offshore contractors and bridge designers are realizing the importance of the early use of offshore geophysics for (i) site characterization, (ii) to reduce the uncertainty of geotechnical conditions thus avoiding designs that may be overly conservative and thus more expensive and (iii) to assist in selecting locations for geotechnical borings.

Jan 1, 2013

By Jamey Rosen, Georgette Hlepas

Verticality data collected from panel and pile elements of seepage barrier walls describe the shape and position of those elements in three dimensions. These data are used to determine if a barrier wall is constructed as designed and if it meets the owner specifications with respect to tolerance (i.e., if each element is sufficiently close to vertical) and overlap (i.e., do adjacent elements overlap sufficiently to prevent leakage). Contractors use verticality data to confirm that their work matches the design, and owners use verticality data to verify the contractor’s work and confirm that specified criteria were met. Project Information Management Systems (PIMS) technology has been applied to the management, visualization, and analysis of verticality data. This paper will provide examples of how contractors and owners have used a PIMS to compile and synthesize data collected during excavations (e.g., from Cutter Soil Mixer and Hydromill drill rig telemetry), and from measurements of completed excavations (e.g., using the Koden ultrasonic tool), and used those data to model excavation geometry. We will present case studies of using these models to estimate backfill placement volumes, and to evaluate the verticality tolerance and overlap between elements.

Sep 8, 2021

"1.0 DESCRIPTIONThis work consists of furnishing all necessary labor, equipment, and materials to install prefabricated vertical (wick) drains in the ground in accordance with the Plans and as specified herein.2.0 REFERENCED CODES AND STANDARDSASTM D4716-08 Standard Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant HeadASTM D4632-08 Standard Test Method for Grab Breaking Load and Elongation of GeotextilesASTM D4533-11 Standard Test Method for Trapezoid Tearing Strength of GeotextilesASTM D4491-99a Standard Test Methods for Water Permeability of Geotextiles by Permittivity (2009)ASTM D4751-04 Standard Test Method for Determining Apparent Opening Size (A.O.S.) of a GeotextileASTM 6918-09 Standard Test Method for Testing Vertical Strip Drains in the Crimped Condition3.0 QUALIFICATIONSThe Contractor shall have successfully completed a minimum of five wick drain installation projects in similar ground conditions, and installed not less than 5,000,000 linear feet (1,525,000 linear m) of wick drain in the past five years. The Contractor shall have a minimum of five continuous years of wick drain installation experience."

Jan 1, 2014

By Gerry Houlahan

"The 2015 Outstanding Project Award (OPA), which recognizes the superior work of DFI members, was awarded for the San Francisco- Oakland Bay Bridge New East Span. The award was presented to representatives from Caltrans and the T.Y. Lin International/Moffatt & Nichol Joint Venture at the DFI 40th Annual Conference on Deep Foundations in Oakland, Calif. A committee selected this project based on size, scope and challenges of the project; degree of innovation and ingenuity exercised; and the uniqueness of the solution to the difficulties of the job. A bridge across the bay between San Francisco and Oakland was proposed as early as 1872, but it took until November 12, 1936, until it became a reality. The bridge spans to the west of Yerba Buena Island were conventional suspension spans, while the east spans used a steel cantilever truss design and simple steel truss spans. This double-deck bridge served the Bay Area well until 1989. In that year, the magnitude 7.1 Loma Prieta earthquake damaged the East Span of the San Francisco-Oakland Bay Bridge. The resulting interruption to service across the bay demonstrated the vital role this bridge plays in the economic and life safety activities of the Bay Area. The project owner, California Department of Transportation (Caltrans), determined that the safest, most cost-effective solution was a total bridge replacement. The Engineer-of-Record, T.Y. Lin International/ Moffatt & Nichol Joint Venture, working closely with Caltrans, the Metropolitan Transportation Commission (MTC) and the California Transportation Commission (CTC), was charged with developing a comprehensive design strategy that met the project’s stringent criteria for seismic safety. These criteria included the new bridge’s designation as a regional Lifeline Structure that must open to emergency traffic shortly after the occurrence of a 1,500-year return period earthquake"

Jan 1, 2015

By Amalia Giannakou

When designing structures in seismically active areas, foundations of critical structures are typically located away from known faults. Indeed many seismic codes prohibit construction in the immediate vicinity of seismically active faults establishing minimum setbacks from the faults. However, for long structures such as bridges, tunnels and pipelines, a fault maybe unavoidable, and fault rupture risk impossible to preclude. This paper presents a case study of a bridge foundation design that incorporates the consequences of fault deformations passing through the foundation. A series of site surveys were conducted to characterize the fault environment, and fault displacement hazard analyses were conducted to develop design displacement demands. Subsequently, numerical analyses were performed to evaluate the fault rupture-induced demands on a pier foundation in terms of displacements and rotations. Initially, analyses were performed that model the free field fault rupture propagation to the ground surface of the fault to ensure that the basic site characteristics are captured. Subsequently, the foundation elements were introduced in the model and the fault rupture is simulated again. The interaction and influence of the foundation on the fault rupture propagation is calculated, and the consequent demands and distortions of the foundation block provide a basis for structural engineers to design the bridge.