Search Documents

By Ed Beswick

Resource Update Drilling Program ? Pre-feasibility ? Exploration Metallurgy Program ? Grindability ? Metallurgical Optimization ? Hydrometallurgical Options Preliminary Mine Development Design Environmental Permitting Infrastructure Development

May 1, 2008

By T. Holmes, D. C. Russell, G. Jolly

"The AMEC Oakville office is involved in the design and construction of an iron ore concentrator located in Liberia. Currently, the site ships Direct Shipped Ore (DSO) to overseas customers. The DSO mine-site and port can experience heavy annual rainfalls. The IMSBC Code requires that cargoes are only accepted for loading when the moisture content of the cargo is less than its Transportable Moisture Limit (TML). The moisture content of the DSO has, on occasions, risen to near or above its TML. AMEC was asked to advise whether the concentrate produced from the new concentrator would or would not have the same problems with moisture content and ship loading as the DSO.INTRODUCTION Liberia was, at one time, the world’s sixth largest exporter of iron ore and used some of the most modern mining operations of their time. However, the country has not produced iron ore over the past seventeen years because of civil unrest. The return of stability to the country has allowed the redevelopment of the iron ore industry. ArcelorMittal Liberia (AML) obtained a concession for mining in the Nimba County area of Liberia (Figure 1) in December, 2004 and has studied the known iron ore deposits and former mining operations in this area. It began phase 1 operations in June 2011 with the direct shipping of high grade ore at a rate of up to 4Mtpa. The processing of the lower grade ore in phase 2 of the project requires additional processing capability to produce at the design rate of 15Mtpa. DSO and Concentrate The DSO in the first phase is selectively mined at an average grade of 60% Fe, and then crushed and screened to -10 mm with no washing or concentration. Testing of samples has indicated a size distribution that is finer than typical sinter feed material, although critical material below 0.10 mm is low in most cases, and overall the ore is coarser than typical concentrates or ultrafine products (Feasibility study report, 2011). The phase 1 DSO facility will cease operation after the phase 2 concentrator comes into operation."

Jan 1, 2014

By D. G. Klaren, E. F. de Boer

Self-cleaning fluidized bed heat exchangers have demonstrated unparalleled performance internationally for the implementation of indirect heat transfer in severely fouling fluid environments. The ingenious configuration of recirculated cleaning particles through the tubes of vertical shell and tube heat exchangers provides the ability to solve any problems that arise as a consequence of tube-side fouling during indirect heat transfer to process fluids or slurries. In most cases, the cleaning particles consist of chopped metal wire, however other process-specific materials have been used. In addition to the mitigation of fouling effects, a number of other significant benefits for slurry heating are afforded by the mode of operation of the self-cleaning fluidized bed heat exchangers. Increased turbulence at the slurry/tube interface is imparted by the action of the fluidised particles, resulting in very high heat transfers at relatively low liquid velocities. Furthermore, given the thixotropic nature of most process slurries, the action of the fluidised particles imparts additional shear to the process slurry, resulting in shear thinning effects with a consequent reduction in pressure drop and enhancement of heat transfer across the heat exchanger. The benefits provided by the self-cleaning fluidized bed heat exchanger make it the ideal option for the indirect heating of laterite nickel slurry for High-Pressure-Acid-Leach (HPAL) plants. This article explains the principle and application of the self-cleaning fluidized bed heat exchanger technology for the processing of laterite nickel and cobalt slurries in HPAL plants. It also presents an elegant method to revamp existing direct heated laterite nickel and cobalt processing plants into an indirect heated configuration employing self-cleaning fluidized bed heat exchangers.

Jan 1, 2004

By L. Boyd, A. Charland, G. Potts, D. Fragomeni, N. O. Lotter

"The Raglan orebody and concentrator has been the subject of study in Process Mineralogy at Falconbridge since 1998. (Lotter and Tuzun, 1998) The orebody is classified into three distinct textural groups, or end members. These are referred to as disseminated, net-textured, and Massive Sulphides, and differ in terms of mineral grain size, nickel grade, hardness, and mineral association. In this paper, it will be shown that the sampling and characterisation of each end member on an individual basis develops a higher-level understanding of the processing requirements and behaviour of the mixture of ore as presented to the mill.The end members have been used in robust prediction of recovery at various grind size p80 from laboratory scale High Confidence Flotation Tests. Weighted mean mixtures of the end members have been mathematically combined to determine impact of textural distribution on metallurgical performance as a function of grind size.The ore end members also vary in hardness and breakage mechanism and have been used to model throughput capability for existing, optimized and retrofit grinding circuits. This modeling has provided a range of expected throughputs as the relative proportions of each end member varies.Finally, the differing grinding requirement per end member has led to the development of grinding and flotation strategy that increases rougher flotation recovery and provides flowsheet options for a concentrator expansion. This leads to further understanding of the plant performance as a function of ore mixture."

Jan 1, 2005

By Jon R. Maki

"EVTAC, an iron ore mine in Minnesota, had trouble meeting the customer’s pellet silica requirements. In addition, the mine plan was moving towards a lower grade ore and funding was not available for plant improvements to compensate for the change in ore or improving quality. Small changes to optimize various processing equipment resulted in significant improvements in both quality and productivity; for example, productivity on one mill line increased by 10% while producing lower silica concentrate. This paper will provide the methodology that allowed EVTAC to improve quality and productivity through process optimization with little capital investment.INTRODUCTION EVTAC, an iron ore mine in Minnesota, had trouble meeting the customer pellet silica requirements. In addition, the short-term mine plan was changing to a lower ore grade. Because of limited funds, EVTAC did not have the capital for investing in the plant to compensate for the ore change or to make improvements to lower product silica levels. Small changes to optimize process equipment resulted in significant improvements in quality and productivity; for example, one mill line feed rates increased by 10% while also producing a higher quality concentrate. These changes were sufficient enough to allow the mine to lower the target ore grade beyond their initial goal. At one time, a $3M flotation facility was considered as a way to meet quality with the new ore grade. However, the process changes were able to accomplish the same silica reduction with roughly a $50,000 investment in VFDs for sump controls. This paper will discuss some of the modifications that allowed EVTAC to meet the quality and production objectives with little capital investment. It also discusses the methodology used to make these process improvements."

Jan 1, 2014

By T. L. McCall

AUTHENTIC records show that coal mining in Cape Breton dates from the year 1720, when the French military authorities obtained coal from what is now known as the Blockhouse seam, in the Morien district, for use at Louisburg, where the fortress, now of such historic interest, was being built. Thereafter, coal was mined more or less continuously, and although, for many years, in a very haphazard way, there was, on the whole, a steady growth towards a better regulation of the industry, culminating in the year 1825 with the arrival of the General Mining Association in Nova Scotia. This Company, more generally known as the G.M.A., had acquired extensive tracts in Brazil and Colombia and had also purchased the mining rights for the whole of Nova Scotia-excepting such areas as had been previously leased-the attraction being the rich veins of copper currently reported as occurring in the Province. These fabulous copper veins, upon examination, failed to materialize, but the engineer sent out to report on them returned with such good accounts of the coalfields he had seen that steps were taken immediately to investigate them. From that rime onward, the history of coal mining in Nova Scotia is one of progress and achievement. One of the first acts of the G.M.A. was to acquire the areas already leased to other concerns and develop these in a masterly fashion, employing the best machinery and talent available at that time. Such dominant control over the minerals of the Province, although it led to orderly development in the several coalfields, also, later on, resulted in restricting operations in the various coal centres to such an extent that a determined effort was put forward by the people of Nova Scotia to end such a state of affairs. Consequently, in 1857, the original lease of the G.M.A. was abrogated, the Company, however, being allowed to retain certain areas in the districts it had already developed. This opened the way for the formation of other coal-mining companies, and numbers of these immediately sprang into existence in the various coal-mining centres. In 1893, the Dominion Coal Company, Limited, was formed by the amalgamation of seven companies operating in the neighbourhood of Glace Bay, in Cape Breton. Later, in 1910, the Dominion Iron & Steel Company, Limited, obtained control of the Cumberland Railway & Coal Company, which had been formed in 1884 to acquire the rights of the two companies working in the Cumberland County coalfield.

Jan 1, 1936

By Peter L. Sheehan, David A. Fawcett, Dennis C. Martin

"Smoky River Coal Limited has successfully completed a major program involving the pattern rock anchoring of a high, steeply dipping footwall slope. The slope dips at approximately 65 to 70 degrees to the north, is benched for the upper 200 feet, is supported with rock anchors for another 240feet, and is unsupported at the pit bottom. In addition to the height and steepness, several structural features including shears, rolls and stratigraphic pinch- outs complicate footwall stability.This paper presents an overview of the project with descriptions of the engineering geology and footwall design, anchor installation, instrumentation and monitoring and a cost summary.IntroductionSmoky River Coal's mines are located in the foothills of the Rocky Mountains near Grande Cache, Alberta, approximately 200 miles west of Edmonton. The Smoky River coal leases were initially developed in the late 1960s and, except for minor shutdowns, have been in continuous operation since 1969 producing a low volatile metallurgical coal, mainly for the export market. Initial coal production was from underground mines; sur face mining started in 1971, and a large surface mine, No.9 Mine, was opened in 1974. Since that time, a number of open pits have been mined within the No.9 Mine area. Surface mining is by conventional shovel-truck method s with the use of a backhoe for mining the narrow pit bottoms.Coal recovery is mainly from the No.4 seam, which has a typical unstructured thickness of 20 feet. The most attractive opportunities for open-pit mining exist in areas of over thickening of the coal seam in the hinge zones of synclines and anticlines and in dip-slope situations. The mining of the more structurally complex pits and steeply-dipping footwall slopes requires that consideration be given to footwall stability."

Jan 1, 1988

"The outlook for Eastern Canada is decreasing coal production over the next few years; however, a reappraisal of the long-term requirements and increased prices of coal could lead to a revitalizing of the industry. The market for Western coal is expanding and is expected to exceed 50 million tons per year in the metallurgical and thermal power fields. Western coal reserves are currently estimated at 119 billion tons. Technical developments in Eastern Canada include a shearer and gate-end support system to mechanically cut the stall and brushing at the tail-end of a longwall. In Western Canada, the most modern equipment is used in mining, beneficiating and shipping coal. Results to date on the underground hydraulic experiments exceed expectations. The importance of reclamation is recognized and plans have been made to restore and re-vegetate disturbed areas and mine dumps. In Eastern Canada, experiments were started to determine the feasibility of coal reclamation from mine dumps, including one dump that is on fire. The Mining Research Centre, Mines Branch, continued to conduct research work oriented toward solving Canadian mining problems The Western office of the Centre, opened in 1970, was set up primarily to study problems associated with a resurgent coal industry."

Jan 1, 1971

By W. L. Sherwood

Present conventional techniques for primary steelmaking in both integrated and non-integrated plants are outlined. 'Direct reduction' alternatives are reviewed and categorized according to the nature of the product produced, with particular emphasis on the limited number designed to yield steel as the end product. A proposed new technique, referred to as the Sherwood Process, is described in some detail as a new combination of selected features from the prior technology. This process is in-tended to realize, in integrated operations, the result of continuons steelmaking directly from the ore in a single plant and, in non-integrated operations, continuons steel-making from a metallic charge of scrap, sponge iron or pig iron. Prominent features are continuons processing in elongated, horizontal, rotary furnace equipment, controlled direct heating of each process stage and, for the over-all integrated process, a size separation for removal of excess solid reductant and other waste just prior to the melting step. Material and energy balances are presented as well as exemplary cost data. Reasons for selecting this particular combination of process elements are dis-cussed.

Jan 1, 1968

By G. F. Cross

INTRODUCTION THE electrical system associated with the mining development of the Hudson Bay Mining and Smelting Company, Limited, at Flin Flon, Manitoba, may be conveniently divided into three main parts, namely, the Island Falls power plant, the transmission line, and the distribution systems at the mine and metallurgical plants. For a description of the Island Falls power plant and the transmission line, the reader is referred to the paper, to be presented at this meeting, by R. W. Davis and M.F. Huffaker (1). The transmission line and sectionalizing combinations are shown diagrammatically in Figure 1. The present paper deals with the distribution systems at the Flin Flon mine and metallurgical plants. THE FLIN FLON DISTRIBUTION SYSTEM In the high-tension sub-station at Flin Flon, each incoming 110 kv. line is provided with manually operated, gang-type disconnecting switches. Each line is connected to Canadian General Electric type F.H.K. 39-60B-F.2 T.P.S.T. 110 kv. 400 amp. oil circuit breakers, each provided with M.K.4 centrifugal motor-operated closing mechanism. Gang-type disconnecting switches are installed on each side of incoming line breakers, and a complete ring bus system is formed through station tie breaker, which is' further provided with gang-type disconnecting switches on either side. The?bus tie breaker is of Canadian Westinghouse design, type G.22B, 110 kv., 400-amp., solenoid-operated. All three breakers are provided with bushing-type current transformers, and the two line breakers are further equipped with bushing-type potential devices. Oxide film lightning arresters (121 kv.) are installed on each incoming line and are located outside the station. Each line is further provided with interlocked gang-operated ground disconnecting switches. All disconnecting switches are mechanically connected to auxiliary switches, which provide pilot service to indicating lamps in the remote-control room, located in a separate building.

Jan 1, 1935

By D. M. May

"Cut-and-fill mining is a stoping method that has been widely utilized in the mining industry over the past forty years. It took preference over shrinkage methods at Levack in the early 1930sbecause of its safety aspects; i.e., prompt support of the stope sidewalls, good working floors and better accessibility to support poor back areas. In addition, higher recoveries of ore were possible because of the flexibility of the method in that silling could take place easily at any horizon; low-grade ore could be sorted and left in the stope as fill and certain zones of rock could be left unmined. With modern techniques, a steady production rate can be established, as filling and mining can be carried out stimultaneously.AIthough there are numerous variations of cut-and-fill mining throughout the world, this paper reviews the original type of mining, with modifications and improvements through the years to present modern practices, with the Levack West operation appearing to be the most productive at this time. Stoping efficiencies have also increased substantially from the original 10 tons per manshift to the present 55 tons per manshift.The paper also outlines the many improvements that have been made with respect to mucking and ground support operations; from hand mucking in a single stope to the use of frontend loaders and haulage trucks in fully accessible stope complexes; and from timber props to roof bolts of various types. Although present methods are extremely satisfactory, experimentation is continually being conducted to improve safety and productivity for future mining.IntroductionThe major mining operations of the Ontario Division of Inco Limited are located in the Sudbury Basin (Fig. 1). Around the rim of this geological formation and within 30 miles of the City of Sudbury are nine producing mines and one ' open pit operated by the company .Ore production currently approximates 11.5 million tons per annum from underground and open-pit operations. Underground mining methods include sub-level caving, shrinkage, cut and fill, undercut and fill, blasthole and vertical retreat. The Levack Complex, the main plant of which is the central Levack Mine, produces 11,000 tons per day.The first prospecting in the Levack area, in 1887, was conducted by James Stobie, who examined rock cuts along the route of the Canadian Pacific Railway to the northwest of Sudbury. However, it wasn't until 1913 that operations commenced at Levack under the Mond Nickel Company."

Jan 1, 1981

By L. Heber Cole

Introductory During the past few years, salt (sodium chloride) strata have been encountered in western Canada in a number of wells, while prospecting for oil and gas. The ever increasing number of such wells points to the presence of a vast salt basin, the boundaries of which are at present unknown. This basin extends in a northwesterly direction from a point near the United States boundary south of Regina, crosses the Saskatchewan- Alberta boundary northwest of Unity, Sask., and continues with more northerly trend to Waterways and beyond. The beds, as encountered, appear to have a general dip to the southwest of between 10 to 20 feet to the mile and a pitch along the strike to the southeast. Thus one finds the salt strata at Waterways, Alta., at 600 feet below the surface (121 feet above sea level) whereas at Radville, Sask. south of Regina, the top of the salt is at a depth of 6,643 feet below the surface (4,430 feet below sea level). Whether this is a continuous salt basin or a series of separate basins is not yet known. We do know however, that in some of the well~ more than one salt horizon occurs while in others which normally should have encountered corresponding beds, the salt strata are absent. This latter condition, however, may occur only in the southern part of Saskatchewan, where a barren area seems to come in from the southwest. In the northwestern part of the basin, on the other hand, the occurrence of the salt strata seems to be more regular and continuous, and depths at which salt should be encountered in a drill hole in this part of the basin may be predicted with a fair degree of accuracy.

Jan 1, 1948

By P. R. Geoffoy, T. Koulomzine

"The discovery of the Mogador deposit concealed by 100 feet of overburden was the result of combined application of geological reasoning, ground geophysical surveys, studies of glacial float and extensive diamond drilling. The ground was acquired because it lay on the projected intersection of the Manville and Laflamme River faults. Systematic ground prospecting led to discovery of mineralized floats. A first unsuccessful exploration campaign lasted several years and consisted of 137 drill holes.In 1951 the boulder nests were reexamined and an associat'on of the mineralized float with boulders of a granodiorite, unknown in outcrops of the district, was established. Consequently, ground magnetic surveys were extended and re-interpreted, and a large anomaly interpreted as corresponding to a batholith was outlined. The existence of the batholith was immediately confirmed by drilling and the Mogador deposit discovered in third hole of new drilling programme in a zone of fractured volcanics paralleling southern contact of batholith.The Mogador deposit is a complex replacement of silicified volcanics by pyrite, pyrrhotite, sphalerite, chalcopyrite and galena carrying values in silver and gold. A total of 1,230,000 tons has been indicated, most of it now classified as fully developed proven ore."

Jan 1, 1960

By John Frostiak, Lloyd Buckingham, Kenneth G. Thomas, Luis Wilson

"The El Indio roasting facility associated with El Indio Mine in Central Chile has operated since 1981. It is a facility developed to remove arsenic and antimony from gold bearing enargite/pyrite flotation concentrates.The three installed roasters are Nichols Herreschoff units each with 14 hearths and measuring 4.85 metres diameter. Hearths are rabbled by central shaft driven rabble arms. Product is progressively heated to 750°C under neutral to reducing atmospheric conditions to drive off labile sulphur, arsenic and antimony.Ancillary equipment includes skip hoist feed arrangements, water cooled screw conveyors for transporting and cooling calcine, gas cyclones, post combustion chambers, heat exchangers, electrostatic precipitators, bag houses, gas scrubbers and packaging facilities .Operating practices, history, mineralogy and results are reviewed. The improvements to arsenic and antimony extraction, ambiental conditions and environmental achievements are discussed.INTRODUCTIONHistoryThe El Indio property lies in the El Indio belt, a copper, gold and silver area approximately 175 km long by 10 km wide. The property is located in the Andes Mountains of the central part of Chile at latitude 30"" South and 160 km from the sea-side city of La Serena. Plant location is at 3850 meters above sea level.The property currently consists of two underground mines feeding the El Indio plant and an open pit feeding the newer Tambo leach plant. The property has been controlled by a succession of owners (St. Joe Minerals, Fluor, Bond Gold International and Lac Minerals Ltd.) before acquisition by Barrick Gold Corporation in 1994."

Jan 1, 1999

By J. -F. Lessard

Most underground mines rely on ore pass systems to ensure the transport of ore and waste. The design and operation of ore pass systems often rely on past experience, which is often anecdotal and at times contradictory in nature. This paper summarizes the current practice in Quebec underground metaliferous mines. The information was collected during a series of site visits in ten underground mines. The database includes information on ore pass configuration, support, materials transited, and overall ore pass performance.

Jan 1, 2006

By Peter A. Hacquebard

Recent drilling programs have shown that the in-situ coal resources of Nova Scotia are very substantial. The grand totals of the measured, indicated and inferred categories amount to 232 m, 646m and 993 m tons, respectively. This vast quantity of coal occurs essentially in five main fields: Sydney, Mabou, Port Hood, Pictou and Springhill. The largest resources (84% of the total) occur in the submarine area of the Sydney coalfield. With a 65% recovery rate, there are at present 150m tons of proven, recoverable coal in Nova Scotia. At a predicted maximum annual production of 5 m tons, this amount equals a lifespan of 30 years. However, additional drilling, particularly in the Sydney offshore area, holds promise of increasing the recoverable reserve tonnage to at least 350 m tons. This figure may be compared with the 484 m tons production obtained during 191 years of mining (from 1785-1976). The geological appraisal of the remaining coal resources in the five fields mentioned is presented in three-dimensional diagrams, per individual seam and corresponding reserve area. In addition, the submarine extensions of the Sydney and Mabou coalfields are discussed in light of results obtained from off shore oil exploration wells. The terminology and standards of coal resource calculations are pointed out, and the phenomenon of seam splitting and its prediction from geological data is illustrated. The availability in Nova Scotia of either thermal or metallurgical coal is considered in relation to rank and sulphur content. This paper was presented in June 1977 at the 90th Annual Meeting of the Mining Society of Nova Scotia. The coal resource estimates, however, have been updated to include the results obtained with the offshore drilling in the Sydney Coalfield to November 1977.

Jan 1, 1979

By G. Reuben Yourt

IN 1935, Wright-Hargreaves Mines, Limited, initiated an enlarged programme of ventilation. In the mine, surveys were made from time to time by the geological staff, and improvements in ventilation were effected to accord with progress in mining as greater depth was attained. In the summer of 1938 an engineer was trained in the technique of dust sampling. Instruments and equipment for this purpose, such as konimeter, microscope, furnace, etc., were purchased, and a suitable office, equipped with laboratory facilities, was provided. The full time of the engineer is devoted to ventilation and dust control. On surface, in the mill crushing-plant and in the assay office and sample crushing room, an elaborate arrangement of hoods and exhaust systems has been installed to eliminate the dust. These installations, however, are not described in the present paper, which deals only with an extensive programme of underground ventilation as a method of coping with high dust concentrations, increasing temperatures and high humilities.

Jan 1, 1940

By M. A. Kessick

Current treatment and disposal procedures are compared for clay slimes resulting from the extraction of Alberta oil sands, the extraction of Florida phosphate matrix, the recovery of diamonds from kimberlite deposits in South Africa, the recovery of kaolin from clay deposits in southwest England and the upgrading of bauxite ore. Published research in the area is reviewed, and common trends which are emerging in the disposal of clay slimes are discussed.

Jan 1, 1978

By Karl J. C. Harries

"12.1. NO DEPRECIATION/GAAPAll calculations and computations relating to the Royalty shall be carried out in accordance with generally accepted accounting principles consistently applied to the extent that such principles are not inconsistent with the provisions of this Schedule and the agreement attached hereto, it being specifically agreed that nothing herein contained shall permit, or be construed to permit, the Operator to deduct any amount for depletion, depreciation, amortization or any deduction that represents a non-cash outlay.Comment: In cases like net profit royalties where recoupment of prior expenditures is permitted, care should be taken to avoid any implication that depreciation may also be taken. It is only logical and equitable that Property Owners should not be permitted an apparent ability to “double dip” with respect to deductions. A provision like this example should accomplish the task. It will be noted that the example specifically contemplates that the negotiated arrangements will prevail over any requirements of GAAP. Accordingly, if the parties agree to an unusual formula for recoupment, it will not be set aside to accommodate GAAP requirements. Under GAAP, revenues and expenditures are accounted for on an accrual basis. In addition, it specifically prohibits the taking of non-cash deductions, which is in keeping with the concept of recoupment.Although in some ways the example states the obvious and could be considered redundant, its presence, especially in provisions contemplating recoupment, makes it clear to the financial people that there may well be some variations from normal practices dictated by GAAP, while at the same time confirming the availability of GAAP to fill any voids.The accounting profession often makes the caveat that application of GAAP is an “art”, not a “science”. GAAP do not provide a cure-all and can create problems that will have to be addressed. For example, GAAP contemplate that asset costs are to be reduced by investment tax credits, which can cause a problem for a payor with more than one mine."

Jan 1, 2003

By F. D. Forgeron

"ONE OF THE FIRST DOCUMENTED APPLICATIONS of soil geochemistry in the Canadian Shield was that carried out by Chisholm in the Kenora district in 1949. This survey proved successful in outlining sulphide-associated gold veins utilizing cold-extractable metals. Since then, mining companies, government agencies - both provincial and federal - and universities have conducted soil investigations. Some of the results are documented in publications, others are on open file in provincial and federal mines departments and, unfortunately, many other investigations with both successful and unsuccessful results are buried in company files or have been discarded. This paper deals with soils within the scope of chemical studies of overburden in the Canadian Shield. The subject is a broad one and some definition is required. The soil investigations discussed herein are those aimed at the testing of specific targets more or less in the source area. This definition distinguishes soil investigations from other overburden studies which commonly monitor metal accumulations at some substantial distance from the metal source. Naturally this distinction is relative, because in many instances there is overlap."

Jan 1, 1971