Search Documents

By Ho-Tun E, Stewart PSB

The definition and recognition of silver minerals is very difficult. In general such minerals occur at low concentration and can be hard to identify and measure using conventional optical mineralogy. The present paper describes the use of the QEM*SEM system to tackle this problem and provide information of use to the metallurgist. Three aspects of QEM*SEM are used to special advantage in this application. Firstly the automated mode of operation is used to make a rapid search for the sparse phases. Secondly the X-ray capability is used to identify the mineral phases. Finally the image analysis programs quantify the distributions of the minerals which are found. The paper deals with the identification stage of the process and with the use of the data which can be derived. Silver minerals which covered a range of ore types and composition were collected and studied in detail. On the basis of these measurements and information received from a number of mining companies regarding the important minerals, a classification table was prepared. This table listed about 40 different silver mineral types which could be identified by QEM*SEM and which were of interest in silver recovery processes. Where the silver occurs in solid solution in concentrations greater than about one per cent, the silver content in the species was subdivided into ranges based on statistical intervals. The QEM*SEM system was programmed to recognise these as separate species. Examples are presented of the use of the system in defining the type and morphology of the silver mineralisation to assist in the assessment of batch flotation test Samples.

Jan 1, 1993

By B Murphy, J van Zyl, G Domingo

In a narrow vein mining scenario, employing preconcentration technology underground not only results in reduced transport and handling costs but may allow alternative mining methods to be implemented, improving overall productivity. Using processing technology underground is not a new concept with underground crushing and screening operations being quite widely utilised. With advances in processing technology over recent years, there are now a number of robust processing methodologies in existence that are capable of performing separation of ore and waste at a relatively coarse size. Many of these technologies are readily adaptable to the underground environment and if employed could result in a number of cost and productivity benefits.Assessment of the oreÆs suitability for preconcentration technology is the first step in harnessing these potential savings. This paper discusses how coarse ore sorting and gravity separation could be employed underground in a narrow-vein scenario and details the test work that is required at the front-end of a project to see if this potential exists.CITATION:Murphy, B, van Zyl, J and Domingo, G, 2012. Underground preconcentration by ore sorting and coarse gravity separation, in Proceedings Narrow Vein Mining 2012 , pp 237-244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By Weber D, Knox PR

The criteria developed for the Argyle Diamond Mine process plant control system are reviewed. The control system installed is described along with a discussion of the method of implementation adopted. The control system was extensively tested prior to instal- lation at site. This approach led to signi- ficant time savings during plant commissioning and facilitated rapid escalation of plant production. The control system has performed satisfactorily with a high level of operator acceptance and basically satisfies the criteria Developed.

Jan 1, 1986

By Kerkhoff G, Wood J

The maximum gas emission into underground workings can be predicted by the use of established methods which have world wide recognition. Changes in gas emission and the influence of the gas and geological environments during longwall mining at Pacific Colliery, were found.to be a typical. The relationship between longwall mining and gassy conditions is found to vary from the European experience because of the different mining and geological conditions encountered, and the higher productivity achieved, by single longwall panels in Australia.

Jan 1, 1988

The patented "Epytensic" pump of Minnovation Ltd, a multiple piston pump, is used widely on shearer loaders and by partial high pressure watcr jet cutting strategically in relation to cutter picks not only improves cutting rates, but saves power and increases the life of gearboxes and picks, as well as improving dust suppression. The "Face Side Pump", also a piston pump, located on the ranging arm gearhead has advantages over gateroad pumps and shearer body pumps. The "Extraction Drum", hydraulic air mover system, linked with the above innovations and high pressure water, have further advantages in methane and dust removal. Some modifications providing these systems need workshop applications but most are possible underground with minimal changes to shearer profiles and advantages of minimising hosing, along with the other advantages stated.

Jan 1, 1991

By Bhaskara Sarma P V R

Solvent extraction of cobalt from an ammoniacal ammonium sulphate medium was carried out using Di(2-Ethyl Hexyl) phosphoric acid in kerosene as diluent. The effect of ammonium chloride and ammonium sulphate on the extraction efficiency was studied. The extracted species in the ammonium chloride and sulphate systems were CoAz2HA.NH4CI and CoA3.HA.2(NH4)2SO4, respectively. Ammonia scrubbing and cobalt stripping studies were carried out from loaded and ammonia free organic Respectively.

Jan 1, 1992

By Just GD, Phillips R

The application of high pressure water jet technology to the drilling of longholes in coal has resulted in the development of a system currently capable of drilling to lengths greater than 200m. Field tests at the German Creek Mine have demonstrated directional control of the holes within a 0.5m section of the seam. Initial application of the technique at the German Creek operations is for drilling methane drainage holes. These developments, in three stages, result from support by the National Energy Research Development and Demonstration Council

Jan 1, 1991

Detailed mapping in the Permian-Triassic clastic sediments of the Southern Alps delineates a number of strike-slip faults, both dextral and sinistral, associated with the major Alpine Fault to the west and displacing a tight array of fault blocks. Concurrent steeply plunging folds are deforming early major folds of probable Cretaceous age, and generating schist locally. To the east a major collapse zone has developed along the crest of a Cretaceous anticline, located over an ancient Permian submarine scarp, with a number of small normal faults. Further east, extensive Carboniferous to Triassic rocks of much the same appearance are exposed as horsts and grabens in a large possible extension zone through central and east Canterbury. This may have crept incrementally from Cretaceous from the offshore Bounty Trough to reach the eastern margins of the Southern Alps in the Pleistocene.

Jan 1, 1990

The Central West of New South Wales is emerging as a significant metallogenic province. The development of Northparkes Mines (North Limited) and the Cadia Hill deposit (Newcrest) are establishing NSW as a highly prospective porphyry copper-gold province. Exploration in the area has been further buoyed by the Ridgeway discovery by Newcrest near Cadia. The fact that the Ridgeway prospect was discovered 300 m below surface under Tertiary basalt cover indicates that surface prospecting can no longer be considered alone as an adequate method to find significant new deposits.

Jan 1, 1997

In eastern China, most of the copper skarn deposits occur in folded troughs which are controlled by the EW-trending faulted fold systems (the Pal-Asian geotectonic domain), and the NNE-trending rift or fault zones (the Marginal-Pacific geotectonic domain), particularly the later. From the north to the south, there are four troughs hosting the main copper skarn deposits in eastern China: the Yanliao Trough, the Yangzi River Trough, The Qiantang-Yuanshui Trough and the Zichen Trough. There are more than 30 copper skarn deposits in eastern China, and ore reserves of each deposit are between 30 to 100 Mt with average grades over 1 % Cu.

Jan 1, 1995

By N Tuffs, R Peace, S Xue

Mine gas control is a major issue in most of the gassy underground coal mines, due to its direct impact on safety, production delays and cost of production. Analysis of the gas data, from different collieries in Australia showed that longwall gas emissions have increased substantially over the years. Simply increasing the number of goaf holes in the panel or decreasing goaf hole spacing seems not to be effective, in controlling high goaf gas emissions. A major research project has been undertaken by CSIRO in collaboration with mine sites to address this goaf gas control issue with the aim of developing effective and optimum goaf gas drainage strategies. The project has combined extensive field studies with computational fluid dynamics (CFD) models, to characterise goaf gas flow patterns and develop effective gas control strategies. The research work specifically involved review of gas control issues at field sites, goaf gas monitoring, tracer gas tests, CFD simulations and extensive field trials. Field demonstration studies of the new optimum strategies have been conducted at two collieries in Australia. The project results have shown that the optimum strategies were highly successful, in improving the overall efficiency of goaf gas drainage systems, at both the field sites. Results of the goaf gas flow characterisation studies and field demonstration studies are summarised in this paper.

Jan 1, 2005

The history of black coal as a fuel dates back in Europe more than 2,300 years, and possibly longer in China. Originally the mining of coal was done by underprivileged people, but with the industrial revolution and the dawn of mechanisation, the status of the coal miner improved. The improvement continued to the present day. Coal miners now take an important role in industrialised countries and enjoy a high standard of living. The miner is amongst the highest paid and best technologically served in any industrial activity. The abundance of coal relative to alternative fuels and its widespread occurrence, brings with it a prosperity much valued in those countries with significant resources such as Australia. Coal will play a major role in easing the world energy shortage. In addition to the conventional usage, throughout the world coal gasification plants are in various stages of development. Coal liquefaction plants are beyond the drawing board stage. Slurry pipelines to supply coal for direct burning in electric generating and other plants are planned. In the current atmosphere of environment consciousness, Australia has to contend with people with only marginal interest trying to influence coal mining activities to the detriment of the overall prosperity of Australia. Fortunately enlightened legislation is the greatest protector of the environment and in many instances great improvement to the environment ensues after mining has passed. With its vast resources of black coal Australia can look forward to a significant role in future supply of fuel. As a result of the trade and industry involved, Australia can become an even more influential country in world politics, trade, and the setting of high living standards.

Jan 1, 1975

In Munich's peculiar hydrogeological conditions (water bearing sand strata between layers of impermeable clay, silt or marl) are proper functioning groundwater lowering methods of decisive importance for underground construc- tion. Shield tunnelling with compressed air has al- ready proved to be successful. In view of growing application of shotcrete tunnelling it was obvious to consider the use of compressed air even here. After a preliminary research-project the first subway section "shotcrete under compressed air" was 1979 awarded in Munich and since that time five sections have been awarded, respectively completed. On the basis of the experiences meanwhile obtained reports will be given stating the frame conditions in which this new construction method can be applied. The tunnels consist of two shells. The outer ist driven by shotcrete under compressed air. In order to keep the air overpressure low, the groundwater often is previously detensioned or partially lowered. The inner shell of watertight concrete is built under atmosperic pressure.

Jan 1, 1987

By L S. Barbour, M K. Meiers

Soil covers for mine waste are subject to changes in structure as a result of root development, and wet/dry or freeze/thaw cycling. The purpose of this study was to evaluate the changes in the hydraulic conductivity of three non-compacted clay covers over time. The covers are located on a sodic/saline overburden fill (30-Dump) at the Syncrude oilsands mine in Fort MacMurray, Alberta, Canada. Monitoring of these covers for temperature, matric suction, and water content by the University of Saskatchewan has been ongoing for more than three years. The three covers (D1, D2, and D3) were constructed in 1999 and are 50 cm, 35 cm, and 100 cm thick. The covers are comprised of a surface layer of reclaimed peat/mineral mix over a secondary reclaimed mineral soil (glacial till or glaciolacustrine clay), placed over a sloping shale surface. Field measurements of hydraulic conductivity within the secondary layer were obtained using a Guelph Permeameter during the 2000, 2001, and 2002 summer field seasons. Repeated measurements were made within the D1, D2, and D3 covers at depths of approximately 40 cm, 30 cm, and 60 cm, respectively. The values of hydraulic conductivity for the covers were similar to each other during each of the field study seasons. The mean hydraulic conductivity of the secondary layer increased every year: 2.5 + 10-6 cm/sec to 2.1 + 10-4 cm/sec to 4.3 + 10-4 cm/sec from 2000 to 2001 to 2002. Soil temperature data shows that one freeze/thaw cycle occurred each year at the measurement depths.

Jan 1, 2003

By C M. Hill

This paper aims to provide a brief overview of the Australian Coal Bed Methane (CBM) industry and more importantly the challenges to sustainable management of the industryÆs by-product, groundwater. In a country where water is scarce and having gone through one of the worst recorded droughts it is vital that this important industry be seen to be managing water in a responsible manner with the greatest environmental and social benefit. Benefits of the water from CBM wells can be enhanced through treatment to produce potable water for domestic or stock purposes, water for irrigation or aquaculture or lower quality or untreated water for industrial or mining purposes. Other options are re-injection of raw water or waste from the treatment processes or discharge to surface waterways. The critical change and difference between CBM projects and traditional oil and gas operations should be that where possible water is no longer disposed of via evaporation ponds with the dual legacy of waste of the water resource and an environmental contamination problem with the remaining salt and brine product.

Jan 1, 2003

A statistical investigation of folding at Mount Isa disclosed similar patterns in both the shales and the "silica dolomite" zones. Analysis of these patterns yields 3 groups of folds fully developed north plunging folds, fully developed south plunging folds, and flexuresrepresenting stages of development of folds. Interpretation of results indicates that a regional force from a southerly direction was responsible for the folding.The general pattern of shearing is allied to that of folding, with the exception of bedding-plane shearing. Many shears resulted from continued application of force on folds which ruptured after overthrusting. Other shears resulted from rupture of the more incompetent shale members, without associated folding. The shear pattern is consistent with the theory of a regional force from a southerly direction.INTRODUCTIONThe notes on folding and shearing presented in this paper are part of a current study of the structural geology of Mount Isa.FOLDING 1Measurement of FoldsInvestigation of folding underground involved the measurement of plunge, strike and dip of the axial plane, and the order of magnitude of each fold, together with its location and the rock type. The total number of folds measured was 701, of which 411 occurred in shale areas and 290 within the "silica dolomite" zones. All folds measured are located on main levels, from 7 level to 13 level inclusive. The sections of the mine involved are the Black Star, Black Rock and Racecourse. Detailed investigation of folds on the upper levels (4, 5 and 6) has not yet been done, but observations there suggest...

Jan 1, 1961

By A Thompson, E Villaescusa

The Western Australian School of Mines (WASM), Kalgoorlie, has been performing dynamic testing of reinforcement systems as part of the Minerals and Energy Research Institute of Western Australia (MERIWA) Projects M349 and M349A sponsored by WASM, the Western Australian State Government and the mining industry. These projects have resulted in the construction and commissioning of the WASM Dynamic Test Facility and a program of reinforcement system testing. The primary purpose of the WASM projects is to evaluate the performance of complete reinforcement systems when subjected to an axial dynamic load. The test procedure, monitoring and associated analysis enable assessments for each component (ie the element, the internal fixing mechanism and the surface hardware) of the reinforcement system. The performance of a reinforcement system is usually defined by a static force-displacement response to axial loading. However, this static response may not be applicable to dynamic loadings associated with violent failure of rock due to overstressing as mines progress to greater depths. It was therefore appropriate that the responses of reinforcement systems subjected to dynamic loading be defined and evaluated. The key findings from the tests on a number of reinforcement systems are presented and recommendations made regarding their application for dynamic loading.

Jan 1, 2008

During October 1947 an Authority to Prospect was granted by the Minister of Mines to lVIount Isa Mines Limited over an area of approximately 75 sq. miles to the north of Mount Isa.Application for the Authority to Prospect had been made after Zinc Corporation Limited had been granted prospecting rights over two areas, one of 1,265 acres immediately to the north of the Mount Isa Mines leases and the other of 1,960 acres adjoining the south end of Mount Isa Mines leases.METHODSAs a means of providing a cheap map of sufficient accuracy on which to plot geological features, both Mount Isa Mines Limited and Zinc Corporation Limited agreed upon aerial photographs and the two companies shared the cost of an aerial photographic survey by Adastra Airways of 130 sq. miles which covered the prospecting areas held by both companies.The photographs were on a scale of 800 ft. to I in. with 60% overlap on the north-south runs and 25% overlap east-west. A set of alternate prints enlarged to 400 ft. to 1 \in. were obtained for field work. The 400 ft. to 1 in. scale unglossed photographs (size 18 in. x 18 in.) were taken On to the field and rock outcrops, and uncorrelated structures were plotted directly on to them in red crayon pencil. The geological observations were then transferred in the office to a tracing on which accuracy of azimuth and scale was controlled by use of a photo mosaic and ground surveys.

Jan 1, 1953

By S P, F Villanueva, R Palomo, D Meadows

During 2002, design and development of the worldÆs largest flotation cell was completed. The cell is the mineral industryÆs first 257 m3 flotation cell, and represents a major development in the design of larger flotation cells, with a 50 per cent increase in cell volume over the widely installed 160 m3 WEMCO« SmartCellTM flotation machine. It is anticipated, in the next few years, world-class copper sulfide concentrators will incorporate 257 m3 flotation cells in their rougher-scavenger flotation circuits. The prototype 257 m3 cell, No 250 SmartCellTM flotation machine is installed in Minera Los PelambresÆ existing rougher flotation circuit. The machine is located in front of the first cell in Row 1 and is followed by nine No 130 SmartCellTM flotation cells. The unit has been in operation since April 2004, and has proven itself in this duty. A key to the successful development of the equipment has been the emphasis placed on fundamental hydrodynamic scale-up criteria. Hydrodynamic factors include superficial gas velocity, water (pulp) circulation through the draft tube, and pulp mixing (distribution) characteristics. This paper will review the scale-up criteria of the No 250 flotation cell, and a case study will be presented on the in-plant testing of the equipment. The case study will document the metallurgical and hydrodynamic performance of the machine. It will also illustrate the economic benefits derived by incorporating larger flotation cells in a modern copper sulfide concentrator.

Jan 1, 2005

By Gillies A. D S, Lee A. H

The major operational objectives of a mine water resource management system (WRMS) are to supply the water needs of the mine and mill, to minimise disturbance to mining due to rainfall flooding or seepage and to dispose of excess water. Historically, company management have placed a significantly lower emphasis on managing the WRMS as compared to managing production. Changing Government legislation concerned with the disposal of water from mine sites is, in many cases making mining companies look more closely at how they manage their water. For example, within the next few years it is likely that prior to mining approval by the Government, mining operations will have to submit water management plans/budgets and contingency strategies in addition to operational plans. While the formulation of a comprehensive water management plan/budget is an additional cost to the company at the mine establishment stage, such plans can be beneficial to the operation in the longer term.The two keys for the efficient design, operation and development of a WRMS are the establishment of written goals which have managerial priority and secondly, access to appropriate good quality data. Managerial priority towards the WRMS will increase as a consequence of the education of mine operators in the benefits to the operation of good WRMS management or less desirably as a requirement to meet Government legislation. The collection of appropriate WRMS data is a more complex issue and to obtain information efficiently and cost effectively relies on the clear definition of the data application.

Jan 1, 1992