Search Documents

By Smith P

The past 20 years have seen the replacement of hydraulic control of longwall mining systems by the neater. smaller and better controlled electronic units.Early problems of moisture and other effects on reliability were overcome to see electronically controlled supports chosen for Corrimal Colliery ten years ago. Lessons from Corrimal and elsewhere, with following improvements and sophistication led to wider use as exemplified by Meco and other electronically controlled supports used in more recent installations in New South Wales, Queensland, USA and Czechoslovakia of the total of over 80 electronically controlled support installations worldwide in the past decade. Present work is toward a fully "integrated face" of British Coal by 1993, incorporating the Meco automatic face straightening system already due for practical use in the UK later this year. However the manless face still appears to be some way off although the present minimum crews and close monitoring, including early warning, are promising stages.

Jan 1, 1991

Reconnaissance geochemical exploration in the vicinity of low angle detachment faults which bound the core of the Paparoa metamorphic core complex yielded Au up to 14 ppm, with 35% of greywacke, granitoid and quartz vein samples in the northern range exceeding the 0.01 ppm detection limit. Au is associated with Ag, As, Sb and Cu anomalies consistent with epithermal-type mineralisation. The Ag and Cu anomalies also distinguish this mineralisation from older, mesothermal Au deposits widespread in the Ordovician 'slate belt' greywackes, which comprise much of the upper plate of the core complex. Baryte, molybdenite, fluorite and stratiform U mineralisation in the northern Paparoa Range may also be related to hydrothermal activity along the detachment fault zones.

Jan 1, 1995

By A Buckingham, R M. Hancock

The underground Sunrise Dam gold mine commenced in October 2003 to extract ore from a series of orebodies with various dips, widths, and ore grades over a strike length of 1.5 km. To successfully operate flat stopes it was identified that a means to extract ore left behind after blasting in stopes with dips ranging from 15 to 40 degrees was needed. Various options were available, which included a bulk water cannon, hand held high-pressure water jet, remote controlled small dozer, several mini excavators and finally a specialised remote controlled excavator from the demolition industry. Trials were commenced for the bulk water cannon option in 2006 that proved that the concept worked, however, the system was too cumbersome to set up for use in cycle with production. Hand washing down using mine (low pressure) water with a two-inch bullhose proved of limited value. The small, one metre high remote controlled dozer as used in South Africa was reviewed, but the steepness of most of the stopes precluded this machine. The hand held high-pressure water jet option is still being investigated; with safety factors still being addressed. Several mini excavators were trialled to clean out the flat stopes with generally poor results, the machines being either too large to fit in the drives and pull ore down or too small with too short reach to effectively and efficiently pull ore out of the stope. In early 2007 a Brokk 330 remote controlled excavator was trialled on site with the low profile of the machine and unique arm configuration proving an effective tool for pulling ore from the footwall of short, flat stopes. A Brokk 330 remote controlled excavator was purchased in late 2007 and is currently in operation.

Jan 1, 2008

This paper reviews the developments in understanding of the entrainment mechanism and its modelling in industrial flotation processes over the last 30 years. Both valuable and gangue minerals in the pulp zone of an industrial flotation machine can be transported through the froth zone to the concentrate launder in the water which must also be transferred from the pulp zone to maintain a stable froth zone in conventional flotation. A size dependent portion of each entrained mineral continues in normal circumstances to the concentrate launder. The size dependency arises because the larger particles are able to drain more successfully from the froth region. Gangue minerals are recovered by a number of mechanisms, entrainment being an important one in many cases. The entrainment mechanism is discussed on the basis of the pattern observed in recovery û size data for minerals. Its industrial implications are discussed and means of minimisation of the importance of the mechanism are also discussed. Various means proposed for mathematical modelling of the entrainment mechanism are also described. The effect of process variables on key parameters in these models is reviewed. Properties of both the pulp and froth zones are discussed where needed and means of taking additional measurements with devices developed over the last ten years are discussed as part of the collection of more detailed data on the flotation process in general and the entrainment mechanism in particular.

Jan 1, 2005

Elimination of zinc by the reduction of iron works dusts is examined. The process consists of blending, filtration, drying, balling, preheating and reduction in the rotary kiln. Dust slurries and dry dusts are mixed and stored in slurry basins and the blended slurry is filtered. In the balling process it is important to make green pellets which will withstand Thermal shock in the preheater and rotary kiln. Preheating to about 2000C is preferred to ensure effective use of coke fines in the blast furnace dust. The coke retained in the pellets accelerates the reduction rate. However, at the initial stage of the reduction the pellets become weakened and have to be heated slowly to prevent ring formation. In order to ensure zinc vaporization, pellets should be heated to a temperature of 1100-11500C in the kiln with injection of l ignite fines from the discharge end. Pellets having a degree of metallization of more than 90% and containing less than 0. 1% zinc have been obtained using a test kiln. The final pellet product is intended for use as blast furnace feed. A new plant with a capacity of 20, 000 tonne of dust per month is now under construct- ion and will be in operation next year.

Jan 1, 1974

The most frequently applied project evaluation criteria are the Net Present Value, the Internal Rate of Return, and the Pay Back Period. Unfortunately, the Internal Rate of Return and the Pay Back Period, if interpreted according to their traditional definitions, easily produce results which contradict the Net Present Value. The reasons for the Net Present Value incompatibility of the two criteria are that these criteria have not been adequately defined and so new, complete definitions are recommended. The concept of the True Rate of Return is proposed as a substitute for the interest rate that the Internal Rate of Return has been believed to represent. The redefined Internal Rate of Return and Pay Back Period criteria, as well as the True Rate of Return are all Net Present Value compatible and can, therefore, serve as independent project evaluation criteria. Also, the correct approach to the evaluation of mutually exclusive alternatives and the status of the often neglected borrowing projects in project evaluation are found to be quite important.

Jan 1, 1991

Anodic stripping voltammetry is an analytical technique which has established some popularity for trace analysis of metals because of its sensitivity, selectivity and capability for simultaneous analysis of some elements. The technique can be readily adapted for field use because of its relative simplicity and low power requirements. This paper describes a relatively new instrument, the Portable Digital Voltammeter, developed by CSIRO, which utilises the glassy carbon electrode in a novel cell design and provides parts per billion (ug/L) sensitivity in an instrument which can be field operated. Ten elements, Zn, Cd, Tl, Pb, Cu, Sb, Bi, Hg, As and Au can be routinely analysed. Many of these elements are of interest to the mining industry, and to exploration geochemistry in particular. Case histories where the instrument has been successfully employed for stream and stream sediment analysis of Cu and Pb, for soil surveys of Cu and Au, and for Au in stream sediments and drill chips indicate there are advantages in having on-site data, during Exploration.

Jan 1, 1987

Hindustan Zinc Limited has successfully installed an In-Stream Analysis and Process Control System in the flotation section of the Balaria Lead-Zinc concentrator at Zawar Mines. The system comprises In-Stream Analysis to continuously monitor lead and zinc levels in feed, concentrates and tailings streams, field instrumentation for reagent distribution and flotation cell level control linked to a central Distributed Control System for supervisory control functions. An intensive training scheme was conducted by the system supplier for concentrator metallurgical and instrumentation engineers. Since commissioning of the system in April 1989, Hindustan Zinc has enjoyed the benefits of improved lead, zinc and silver recoveries, improved concentrate grade control and reduced reagent costs.

Jan 1, 1991

By Gardner CE

Uranium occurrences and the probable Australian reserves are discussed and the recovery and processing methods used in treatment plants at Radium Hill and Port Pirie, S.A., Rum Jungle and Moline, N.T., and Mary Kathleen, Qid. are reviewed. The broad aspects of the application of nuclear power in Australia are then considered, and those factors of greatest significance are highlighted. It is these factors that are most likely to dictate the future role of nuclear generation in Australia. In commenting on private industry applications, the paper emphasises that each case must be considered on its own merits, and a warning is given that general statements can be misleading. In the long-term situation nuclear power is considered to be capable of playing a leading role and the discussion covers desalination and high load industries although short term applications appear difficult to justify. In non-power applications for nuclear energy reference is made to isotopes and the uses of nuclear devices in mining and civil engineering with a pertinent comment on safety.

Jan 1, 1970

Titanium tetrachloride may be reduced to trichloride with hydrogen on a hot tungsten filament and other hot: surfaces. The effect of temperature, time and size of t.he filament on the rate of reaction has been studied. A laboratory unit for preparing a few pounds of trichloride at a time is described. The yield of trichloride is 2·2 - 2·4 gm/sq. cm. of hot surface/hour at 1,000°C. and the energy requirement 3'5-4 kWh/pound of trichloride produced.'INTRODUCTIONThe lower chlorides of titanium (titanium tri- and dichlorides) are amenable to electrolysis, being electrovalent in nature. Furthermore, relative to other oxygen-free titanium salts, they are easy to prepare in a pure state and their use has been investigated to prepare titanium. The experimentaJ work described in this paper deals with the preparation of titanium trichloride by reduction of titanium tetrachloride with hydrogen on hot surfaces.REDUCING AGENTS FOR TITANIUM TETRACHLORIDEThe free energy diagram (Fig. 1) for the formation of chlorides suggests that titanium' tetrachloride may be reduced to trichloride by various reducing agents such as aluminium, zinc, arsenic, antimony, tin, mercury, silver, hydrogen, sodium, potassium and magnesium. Ruff and Neumann (1923), Thorpe (1885) , Billy and Brasseur (1935) and Seurbert and Schmidt (1892) used various metals to reduce tetrachloride to trichloride and found that the yields were invariably low and the products difficult to separate.Besides the metallic reducing agents, hydrogen may also be used to reduce titanium tetrachloride to trichloride.Goerges and Stahler (1909) obtained a deposit of violet...

Jan 1, 1956

Martite-goethite high-grade iron ore deposits that show no trace of hydrothermal alteration may extend to more than 200 m below the permanent water table and are typically saprolite with evidence of exposure to the physical, chemical and biogenic processes of soil formation restricted to the low-grade goethitised upper levels. Typically no evidence of the prior presence of chert bands is discernable within the ore yet it has been assumed that these ore deposits derive from cherty banded iron formation (BIF) through supergene leaching of the chert bands and thus classified as supergene iron ore deposits. The fact that chert bands are absent and that these ore deposits are highly weathered does not prove supergene leaching of the chert bands. Quartz is one of the most resistant minerals to chemical weathering within the saprolite and large scale dissolution of quartz is absent from all other quartz-bearing saprolites, yet this unlikely process is accepted without question as the origin of the most abundant form of high-grade iron ore deposits. It is proposed that martite-goethite high-grade iron ore deposits formed only from BIF in which chert bands were absent prior to weathering. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Mansor A. N

Results are reported for the computer simulation of heap leaching of mixed copper oxide and sulphide ores. They resemble those obtained from testwork in terms of a substantial peak in the copper concentration of the pregnant solution, an initial period when no copper emerges and a lengthy period towards the end when the copper concentration and the daily increment in copper recovery are low. The simulation can be used to forecast process results before any column or similar testwork is performed. Potential applications of the simulation to process design, operating strategy and optimisation are discussed. Three modes of operation are identified that correspond to different performance patterns and dependencies on ore and process variables. The relative merits of different operating strategies for approaching the ideal performance are being investigated. For process design and development purposes, the simulation may be used with a limited testwork programme to achieve significant savings in time and resources.

Jan 1, 1989

By Parker RL

A 250 tons per day ammonia-ammonium carbonate leaching plant is now being operated by Samin Limited, to extract copper from the oxidised ores at the Burra mine. This forms the first stage of a plant, which will eventually have a capacity in excess of 1,000 tons per day. The article reviews the history of the mines at Burra and the metallurgical studies which have been undertaken since the old mines closed in 1917, in an endeavour to recover the copper from the low-grade deposits left by the original miners. The reasons why an ammonia leaching process was selected instead of the conventional flotation or acid leaching methods are discussed. The paper concludes with a detailed description of the plant and the basis on which it was designed.

Jan 1, 1971

China has large amounts of iron ore reserves, but iron ore in China, with low-grade, small disseminated particles and many other associated minerals, is difficult to dress. In recent years, with the fast development of China's steel industry, the demand for iron ore has increased markedly. The new technologies in iron ore dressing in China are very effective in processing haematite and other difficult to dress iron ores. The iron ore grade and recovery rate has been improved. This result alleviates the difficulty in iron ore supply in China.

Jan 1, 2007

I start with some lines from "Pleasures of Hope" by the poet Campbell, published in 1798, which sets the flavour of what I am going to say. They blissful omens bid my spirit see The boundless fields of rapture yet to be; I watch the wheels of Nature's mazy plan, And learn the future by the past of man. I hope to echo the poet's optimistic view of what is yet to come. I am not sure I can find all the omens blissful but we all have some experience of what the wheels of Nature's mazy plan get up to. His advice to learn the future by the past of man seemed sensible to follow, so on the principle that the past of several men would be better than one alone I invited Alan Attwood, Maurice Cahalan, Gavin Moncrieff, Derek Temple, and Peter Wright to help me prepare this address; I am most grateful to them for their contributions. Of the technologies covered in this sequence of keynote addresses, metallurgy is the one which is closest to our consumers. On the age-old principle, which I do not expect to see changed in the 21st Century, that production is about providing the customer with what he wants, when he wants it, where he wants it, and at a price he can afford, I think we should start by trying to see how the market place is likely to develop, and to work back from there to review what technology we need to meet these demands.

Jan 1, 1986

By Milner E. F

Thallium is largely volatilized during sintering in the conventional sinter/blast furnace production of lead. The new direct oxygen smelting processes will force the thallium into the bullion, necessitating a means of removal to avoid contamination of the refined lead. Pilot plant testwork demonstrated that thallium was efficiently removed from lead bullion by treatment with molten zinc chloride. The spent zinc chloride salt was treated in the laboratory to recover lead sulphate, a zinc chloride solution, and a thallous chloride salt containing over 80% thallium. Cominco is installing this thallium process as part of its Trail Lead Smelter Modernization Program which will commission a QSL bath smelter in late 1989.

Jan 1, 1989

By C Fountain

It is commonly known that copper smelter terms include penalties if the concentrations of elements, such as arsenic, mercury and fluorine, exceed stipulated limits. It is less commonly known that the behaviour of these elements in the smelters can depend on the processes used to treat the concentrate. The principle behind the penalties is to compensate the smelters and refineries for additional costs caused by the presence of the penalty elements, but these costs will vary depending on the process used and the location of the smelter.The issues caused by the minor elements include effects on the occupational health of smelter workers, increased environmental disposal costs, increased operating costs and reduced cathode copper quality.The effects of minor elements can be surprising. High levels of arsenic in concentrate are considered undesirable, but some smelters add arsenic to anode copper to improve the performance of the refinery.Excess concentrations of some elements will result in rejection of concentrates by smelters. China has blanket import bans on copper concentrates with concentrations of lead, arsenic cadmium, fluorine and mercury exceeding specified levels.This paper will review the behaviour of minor elements in smelters and refineries, explaining the deleterious effects of each of them, to provide a greater understanding for people and organisations wishing to market copper concentrates.CITATION:Fountain, C, 2013. The whys and wherefores of penalty elements in copper concentrates, in Proceedings MetPlant 2013 , pp 502-518 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By R G. Alford

Braeside Borefield, located 120 km southwest of Mackay, is owned by BHP Mitsui Coal Pty Ltd (BHP Mitsui). The borefield provides water to BHP MitsuiÆs South Walker Creek and Riverside Coal Mines and communities in the northern portion of the Bowen Basin. Braeside Borefield has also provided water for other users in the region, including the Peak Downs, Goonyella and Saraji Coal Mines owned by BHP Billiton Mitsubishi Alliance (BMA). Water is sourced from alluvial sediments at the confluence of Nebo and Denison Creeks, and transferred a distance of almost 100 km to Riverside Mine and other users. Since commissioning in 1983, monitoring and maintenance programs have been key elements in borefield management. The impact of pumping on groundwater resources is monitored at the borefield, upstream and downstream over a distance of about 50 km. Current annual pumping is of the order of 4000 ML, and in excess of 50 000 ML has been pumped since the commencement of borefield operations. Detailed reviews of borefield performance are conducted every two years. BHP Mitsui actively participates in community consultation on groundwater issues arising from operation of the borefield. Declining groundwater levels from prolonged drought conditions have increased community interest in management of the borefield. Rehabilitation of existing production bores and augmentation of the borefield is currently being investigated to more evenly distribute pumping rather than to increase overall capacity.

Jan 1, 2003

By J L. Edwards

High resolution, acoustic scanning technology has emerged in recent years as a powerful wireline tool for identifying the occurrence and orientation of structures and borehole breakout û the latter being a strong indicator of horizontal stress directions. While other wireline techniques such as dip metre and calliper logging can provide some of these data in a fairly rudimentary way, the quality and ease of interpretation of acoustic scanner logs provides a level of detail that significantly enhances the risk profile of the analysis which more than compensates for their additional upfront cost (MacGregor, 2002). As is often the case with such technology it is one thing to generate a data set that describes the attributes of the various features apparent in a log, and another to be able to analyse those data in such a way that their individual and collective impact on mine planning issues can be readily assessed (MacGregor, 2003). This paper describes a process for the interactive manipulation and visualisation of joint and breakout data to enable them to be effectively included in the mine design process.

Jan 1, 2009

A thousand writers have harped upon the wondrous nature of the inventive faculty. They realise that man is a creator, and that capital and labour alike are, and will always be impotent without machinery and processes that is invention. What Bacon has said is echoed by them all, "the introduction of new inventions seemeth to be the very chiefest of human actions. The benefit of new inventions may extend to all mankind-they make all men happy without injury to 'any' they are new creations and imitations of God's own works." My remarks will occupy another field I will refer to some of those features of the Patent Laws of different countries, which prevent the use of new inventions, oppress the development or inventive' genius, and diminish human happiness and progress' Wherever Patent Laws are framed and administered upon wrong principles, these results are inevitably found. A concise, complete, common-sense comparison of the chief Patent Laws of the world cannot easily be found but to avoid seeing scrappy, misleading references to Patent Law in the press particularly the English-would be equally difficult. Writers who are considered authorities so frequently make minor issues prominent and so uniformly fail to give weight to fundamental principles that the effect on the public is to mislead.