Search Documents

By J Moncrieff, P Bellairs

The Black Star Open Cut is located immediately adjacent to the township of Mt Isa and is situated in the middle of extensive pre-existing infrastructure including two concentrators, two smelters, a wet fill plant and two shafts. At any one time there are in excess of 500 people working on the surface within an industry-accepted 600 m exclusion zone from Black Star blasts. Apart from the surface operations there are also the underground operations including the lead mine (closed in December 2005) and the Enterprise and X-41 mines that must clear for all Black Star blasts. The application of industry standard blasting exclusion zones (600 m) was risk assessed as imposing operationally prohibitive constraints which could cause significant business interruption due to the logistical challenges required to ensure that all personnel from surface plants were evacuated for each blast and potential for lost production whilst these personnel were not operating the plant. In was therefore an imperative for the blast exclusion zone to be reduced. This was achieved by the: use of a QA/QC team to ensure that relevant drill and blast implementation is within an acceptable tolerance (KPIs) from design; use of high-quality stemming material called HMR, which is a by- product of the concentrating process and is generally sized at -14 mm with very little fines; implementation of appropriate training and support to Black StarÆs own blast crews, reinforcing the need to achieve the designed amount of stemming in every hole; and provision of appropriate support from Black StarÆs management for additional resources to ensure that every blast achieves design within the KPIs but especially in high-risk areas. The blast exclusion zone was successfully reduced after monitoring the flyrock results from more than 176 blasts. Black Star Open Cut now maintains a minimum blast exclusion of 200 m in critical areas; however, general blasting currently uses a 250 m exclusion as this provides additional risk management whilst still minimising the logistics associated with clearing and securing the slightly increased area.

Jan 1, 2007

By Ward S. C, Gardner J. H

In 1990, Alcoa of Australia Limited was elected to the Global 500 Roll of Honour of the United Nations Environment Program for the environmental management and rehabilitation of the bauxite mines in Western Australia. This award placed Alcoa in the international best practice category. The story of constant improvement spans more than 20 years from a 'trial and error' start to a strategically focussed and research driven program today. The main driving force has come from within the company, against a set of strong corporate values and a well publicised Vision based on 'excellence through quality'. Along the way public opinion, action group protests, increased legislative controls together with the professional competence of internal and external environmental resources have all played a part in arriving at the level of current environmental management and mine rehabilitation performance. There were numerous lessons learned here during the evolution and maintenance of best practice. These included: I . To work diligently in obtaining a vision or strategic intent on mine site rehabilitation and environmental management - don't be easily dissuaded.

Jan 1, 1995

of the multitude of physiographic problems of immediate interest in volcanic terranes, it is the origin of the magma forming the magnificent volcanoes that is perhaps the most mysterious. Unlike anywhere else on earth, the possible locations of magma production beneath the convergent margins are strongly limited in depth and areal extent. Yet the exact process by which magma is produced still stands elusive, even in light of tremendous gains in analytical and physical insight. The principal aim here is to discuss some of what has been revealed about the physics and chemistry of the origin and evolution of island are magmas.

Jan 1, 1987

By J Col, D La Rosa, W Valery, A Jankovic

Metso Minerals Process Technology Asia-Pacific and South America (MMPT) has been working with operations around the world to increase their efficiency through æMine-to-MillÆ or Process Integration and Optimisation (PIO) projects. These projects have delivered significant improvements in mine efficiency, mill throughput and reduced operating costs at mines around the world. The MMPT methodology involves rock characterisation, site auditing, data collection, modelling/simulation and implementation of integrated operating and control strategies on site. This results in significant benefits to the operations û for example, 5 to 20 per cent increases in concentrator throughput have been measured. MMPTÆs rock characterisation utilises simple and inexpensive measurements that can be performed by trained site personnel. The advantage of these measurements is that a large amount of data can be collected in a very short timeframe, as the samples do not require shipping to an outside laboratory. Typically, a PIO project starts with a site visit to perform blasting and process audits, collect high quality data including measurements of run-of-mine fragmentation and survey data around all crushing and grinding circuits. These measurements are combined with rock characterisation and the definition of strength and structure domains to model the complete production chain. Site-specific models of the blast fragmentation, crushing, grinding and flotation processes can then be developed. This proven methodology has applications ranging from greenfield projects to long-standing operations with AG/SAG or conventional grinding circuits. Process improvements can be higher mining productivity, higher mill throughput, decreased overall operating costs and higher flotation or leach recovery. This paper discusses a recent application of PIO conducted at a large open pit operation in South America and emphasises the potential that every operation has to ædo more with what they haveÆ.

Jan 1, 2007

The ore deposits investigated are composed primarily of hcmatite and can be grouped into three categories depending on the amount of leaching of silica and carbonate which has occurred from the original iron formation, and on the amount of recrystallization of the hematite. Minor constituents are magnetite. goethite, and quartz.Texturally. there are five different types of hematite, formed at different stages during the genesis of the ores.These are1. anhedral hematite grains formed by recrystallization of hematite already present in the original iron formation.2. hematite formed by martitization of euhedral magnetite, 3. massive aggregates of fine- to medium-grain hematite formed by recrystallization of (l) and (2).4. tabular or prismatic hematite grains occurring around the boundaries of the massive aggregates or martite euhedra. and in fractures and5. specular hematite. which is present in fractures in ore types (l) to (4).Minor and trace-element analyses, determined using an electron-probe microanalyser. indicated that only silica (less than 0·01 per cent) and cobalt (less than 0·002 per cent) were present in the magnetite and hematite from unaltered iron formation and in the hematite from the ores. Low concentrations of trace elements are typical of magnetite in ores formed as marine precipitates. On the basis of the analyses alone. it proved impossible to distinguish between the five hematite types. A determination of the variation in rare-earth trace element contents between iron oxides in the iron formation and iron oxides in the ores indicates that the rare earths were depleted during ore formation. A possible explanation is that they were removed in solution with silica as it was leached from the iron formation.

Jan 1, 1971

By B C. Povey

HPGR technology has been used at a number of magnetite mines in the world and have significant energy advantages over SAG and AG technologies. The early design at Los Colorados in Chile has been in operation for more than 12 years - and operates very successfully though only reduces the feed size to -5mmThe Whyalla project magnet design pushed the concept to produce a preconcentrate of 80%-350micron - a significant reduction on previous plants though with some wear problems in the early years. The Karara design backpedalled slightly and will only crush to 80%-1.8mm.However, the design issues of using a HPGR to further reduce the feed size continue to be explored. The aim is to reduce the process risks associated with wear and also to reduce the complexity of the downstream process - with consequent benefits in terms of capital and operating costs.The designs are being developed for a couple of projects - one planned to produce 20Mtpa of concentrate with the potential to not only remove SAG and AG milling but also ball milling. The concept is to use multiple passing through the HPGR since, on the data available, the efficiency of the HPGR to reduce size does not significantly diminish as the feed size is reduce. This can be have benefits in both capital and operating cost.CITATION:Povey, B C, 2013. Pushing the use of high pressure grinding rolls in magnetite circuits, in Proceedings MetPlant 2013 , pp 176-189 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Brien RT, O&apos

The work reported in this paper extends,-bhsb on the "Heat Hardening of Artificial Magnetite ;Pellets"., which was described at the- International Symposium on Agglomeration ;-sponsored by the American Institute. of Mining, Metallurgical and Petroleum Engineers at Philadelphia; U.S.A. in April, 1961. Whereas- that work was of a.,more basic nature, -serving to illustrate the suitability of artificialòmagnetites with various.admixtures, to the application of heat hardened pellets, on: this occasion the aim-is to illustrate the procedures-which were used-to- establish the dimensions of commercialòrecuperativ strands for Australian raw materials,The nature of the pellet feed, i.e. relatively uniform :spheres of4 3/8 in. - 7/16. in. diameter, makes it possible to use small scale static pots for test work. By the use of a closed system and the measurement of suctions, gas f lows, and temperatures through beds, the speed and heat requirements of the various stages of heat hardening can be measured, so: that for a specified quality of product estimates can be made of the broad design characteristics of a moving grate system. In practice of course it is .usual to correlate the data from this type-of :experimental 'apparatus with . existing production units upon which good operating data, in the statistical sense, are available.

Jan 1, 1963

Over the past seven years, a combination of New Zealand-, Australian- and German-led research voyages using the research vessels Tangaroa, Southern Surveyor, and Sonne respectively, have revolutionised our understanding of the Kermadec-Tonga arc-backarc systems. This convergent margin is the most seismically-active subduction zone system on Earth with convergence rates steadily increasing northwards from the Hikurangi Trench to ~250 mm/year at northern Tonga. In combination with the intra-oceanic setting, factors potentially producing magmatic, tectonic, and hydrothermal variability in this system include an increase in potentially subductable sediment northwards along-strike, intersection of the Louisville Ridge (hot-spot chain) and Osbourn Trough (paleo-spreading centre) with the arc at ~25¦S, and the possibility of Samoan (hot-spot) plume ingression in the northern Lau Basin. The bulk of the magmatism is submarine; whereas only a few emergent (some transient) volcanic islands exist, about 80 submarine volcanic centres of significant size (>1000 m above surrounding sea floor) are present between White Island in the south to north of Tafahi in Tonga. About 35 per cent of these centres are hydrothermally active. Important petrogenetic features of the volcanic rocks along this arc system are the abundance of rhyolite (some quartz-amphibole-bearing), and the outcrop of primitive olivine-clinopyroxene-phyric basalts in satellite cones of the major edifices. Many of the edifices consist of complex caldera systems. Eruptions from and degradation of these edifices were probably tsunamigenic. Many of the hydrothermal systems developed within the edifices are likely destroyed during the sector collapses which are the characteristic edifice degradation mode. There are three backarc spreading systems along this margin: the Havre Trough, Valu Fa-Eastern Lau Spreading Centre, and the nascent Fonualei Rifts. The latter are particularly notable in having captured the entire suprasubduction zone magmatic flux for a distance of about 150 km, shutting down the adjacent volcanic front arc volcanoes.

Jan 1, 2005

By H Holmstr÷m, A Widerlund, M Lindvall

At the Kristineberg mine in northern Sweden sulfide-rich, poorly buffered tailings have been deposited in five impoundments located along a valley. The tailings area has been remediated by applying a combination of till cover and flooding. A new method that has been applied to parts of the tailings area is to raise the groundwater table to saturate the tailings. By increasing pH by liming, thereby reducing metal mobility, a water-covered downstream impoundment is functioning as a trap for metals released from the till-covered impoundments upstream. In this paper the efficiency of the system approach used at Kristineberg is evaluated. Progressive changes of water quality from groundwater in the upstream till-covered impoundments via surface streams within the pond system to the water in the flooded downstream pond and its outlet are described. The results show that the system approach used in the design of the remediation programme of the tailings works as planned. The sulfide oxidation rate has decreased in the till-covered impoundments, and, as predicted, there is an out-flush of old weathering products which will continue for at least five years before equilibrium is reached. The groundwater in the till-covered impoundments has high concentrations of Fe, S, Mg and Zn, but the concentrations of metals such as Cu, Cd and Pb are much lower than before the till cover was applied. The limed pond is an efficient metal trap, with concentrations as high as 2.76 per cent Zn and 0.28 per cent Cu in the calcite-gypsum sludge developed on the tailings. The outlet from the flooded pond, and thus from the whole mining area, releases small amounts of metals to the recipient in comparison to the amounts that are in movement within the mining area. During the period May to November, 13 kg dissolved Zn and 111 kg particulate Zn was released to the recipient, whereas a total of 27 000 kg was transported by surface water within the impoundment system during the same period. The results from Kristineberg show that when planning remediation of complex mining areas, it is useful to adopt a system approach in which different methods are used on different parts of the area along the flow path of the drainage water, whereas flooding of the downstream pond is the key to the performance of the entire system.

Jan 1, 2003

By C Quirion

Agnico-Eagle Mines Limited, Laronde Division, operates the deepest single-lift shaft in the western hemisphere. The initial Penna hoisting plant was designed for a production rate of 1800 tonnes per day (t/d) from a 2240 m deep shaft. Exploration success, while sinking the shaft, led to a decision in 1998 to increase the production rate to 4500 t/d of ore from a loading depth of 2200 m. The new production rate was achieved by increasing the size of the rope and reducing the rope static factor from the existing 5.0 required by regulation to a static factor using the formula 25 000/(4000 + L) contained in a draft document that would eventually become SABS 0294 in South Africa. The formula permits Laronde to use a static factor as low as 4.0. The upgraded Penna hoisting system is the first hoisting plant outside of South Africa to meet the South African requirements. This paper describes the conversion of the hoisting plant to the lower rope selection factor in the year 2000 and the operating and maintenance issues experienced since then.

Jan 1, 2005

The subject of heat sources in deep hard rock mines, the limitation of forced ventilation to cope with these heat loads and the sizing of refrigeration plants to boost the cooling effect of the ventilation air are discussed. The development of plant selection criteria and operating experience at North Broken Hill Limited is outlined. Future options for North Broken Hill Limited and like deep mines are summarised.

Jan 1, 1982

By M A. Etheridge

The evolution of economic precious metal and copper-gold deposits in high-level igneous terranes is dependent on very efficient fluid focussing. This is most readily achieved by contemporaneous deformation, igneous intrusion and hydrothermal activity. Mineralisation in these environments generally occurs in fault and fault-vein arrays developed in the cover sedimentary and volcanics sequences above older regional scale fault systems. Such reactivated fault systems are particularly prone to developing tile complex fracture arrays, extreme local dilation and dramatic increases in permeability that are necessary to efficiently focus hydrothermal fluid and produce large mineral deposits. The arc systems of tilePacific rim are typically structurally and tectonically complex. At any given period in the evolution of an arc system, it may be dominated by extensional, compressional or strike-slip deformation. Indeed, it is common for the tectonic environment to change repeatedly through the development of a single arc segment. As a result, structures formed in one tectonic environment are commonly complexly reactivated in quite different environments later in arc evolution. These complexly reactivated structures have greater potential to localise extreme fracturing, dilation and fluid flux than primary structures. Application of this knowledge to practical exploration requires an understanding of the primary geometry of the controlling fault systems, the fault movements during reactivation, intrusion and mineralisation, and the consequent location and geometry of dilational sites. Simple 2D lineament analysis and targeting on lineament intersections does not suffice. Chemical processes that results from structurally focussed fluid flow may also contribute to permeability enhancement and further enhance fluid flux. Two main types of chemical feedback are important. The first involves selective dissolution of minerals during alteration and tile consequent production of increased porosity and permeability. The second occurs where alteration changes the mechanical properties of tile rock mass, especially where it leads to a greater propensity for fracture (eg by silification). In near-surface environments (< ~1 km), geomorphic processes complement fault systems in focussing fluid flow to develop sub-horizontal bodies of mineralisation, such as the giant Ladolam gold deposit (>42 million ounces of gold).   Along with classification schemes which stress crustal level, host rocks and alteration assemblages, the styles of high level 'epithermal' and reated deposits must also be considered in respect of their controlling co-active fault structures. Such structural understanding, combined with understanding of tile chemical processes involved (eg host rock reactivity), provides a major tool for exploration particularly in terrains obscured by deep weathering. Geological interpretation based on integration of field mapping with magnetic, radiometric and other remotely sensed imagery provides a powerful complementary tool to the traditional geochemical and geophysical targeting techniques. Timely and effective geological input is capable of reducing exploration risk and providing a more cost-effective basis for drilling and development. Examples of deposits associated with fault reactivation in extensional, compressional and strike-slip settings within arc systems are discussed in this context.

Jan 1, 1995

The .subject of this paper is to briefly outline various methods of stockpiling and reclaiming, and the use of different types of bucketwheel re- claimers and stackers in these operations. The paper examines briefly the different types of bucketwheel equipment, their operations and relates them to different stockpile layouts, giving examples of their application in Australia.

Jan 1, 1973

By Townsend MG, Evans RB

In Northland, New Zealand, localised large deposits of halloysite clay have been produced by in-situ alteration of rhyolite volcanics of Pliocene or Pleistocene age, which were erupted through pre- Pliocene sedimentary strata and locally through Pleistocene basalt; and which were subsequently onlapped by further basalt flows. Alteration to clay has been a result of both hydrothermal and of meteoric processes, and decreases in intensity of alteration with increasing depth.The raw material is crushed and fractionated to produce a product of less than 2 micron particle size, which is of exceptional whiteness and brightness. The unique properties of the clays render them highly desirable for specialised ceramic purposes.

Jan 1, 1990

Iron formation-hosted iron ore deposits account for the majority of current world iron ore production and consist of three classes: unenriched primary iron formation with typically 25 to 45 wt per cent Fe; martite-goethite ore formed by supergene processes, with abundant hydrous iron oxides containing 60 to 63 wt per cent Fe; and high-grade hematite ores thought to be of hypogene or metamorphic origin overprinted by subsequent supergene enrichment with 60 to 68 wt per cent Fe.Individual iron ore deposits range from a few millions of tonnes to over two billion tonnes at >64 wt per cent Fe, although most are within the range of 200 to 500 Mt. In the Hamersley Province of Western Australia, martite-goethite ores are largely developed in the Marra Mamba Iron Formation, although high (>0.08 per cent P) phosphorous mineralisation is also well developed in the stratigraphically higher Brockman Iron Formation. Whilst the vast majority of high-grade microplaty hematite ore is best developed in the Brockman Iron Formation, this paper provides the first textural evidence of locally significant microplaty hematite mineralisation in the Nammuldi Member of the Marra Mamba Iron Formation, in the Chichester Ranges at the Christmas Creek, Cloud Break and Mount Nicholas prospects. Petrographic studies have identified a high-grade Fe texture composed of nanometre scale plates of hematite in mineralised sections of primary microplaty hematite deposits in the Pilbara and elsewhere, well below the normal depth of weathering or dehydration. The population of nanometre to micrometre scale hematite plates is interpreted to represent various stages of nucleation, crystallisation and progressive growth of hematite from the primary ore-forming fluid in areas that were once iron-rich carbonates or silicates in the BIF.

Jan 1, 2005

By Postupack C

A major problem that has continued to plague the surface and underground coal industries is blast induced damage to the coal seam. Blasting Analysis International, in conjunction with a number of other organizations, has continued to address this concern through 14 years of field research in 68 full-scale production environments worldwide. Compiled results were obtained from varying field conditions. These included single and multiple seam coal mines, horizontal, rolling and steeply dipping coal seams and varied borehole diameters (ranging from 102 to 381 mm) and when using various explosive formulations. Results are discussed in detail along with the tools, test methods and analysis techniques to identify and quantify the problems. Over ten major causes of coal damage were identified. A number of practical and economic recommendations are presented that can benefit the entire coal and blasting industry especially in commercial operations whose economic growth relies heavily upon recovering an undamaged coal seam.

Jan 1, 1995

By J S. Petersen

The occurrence of coarse gold particles leading to grade complexity and sampling challenges is a common feature of many gold deposits. Poorly designed sampling protocols applied to these deposit types can lead to an excessively high fundamental sampling error. Together with other errors, the fundamental sampling error contributes to the nugget effect. Proper sample collection, preparation and assay protocols are required to minimise this error, and hence reduce the total nugget effect. Reduction of the nugget effect is a key requirement for subsequent geostatistical resource estimates to be effective. A case study from the Nalunaq gold mine in Greenland is presented, which is characterised by notable quantities of coarse gold (>30 per cent +100 ¦m gold) hosted in quartz veins. Diamond drilling provides a good measure of gross geological continuity at practical grid spacings, but is not considered to represent the mineralisation effectively. On-reef development with face and bulk sampling, together with detailed geological studies were undertaken during the resource delineation phase. This contribution describes the nature of the Nalunaq deposit, its gold particle size characteristics, how sampling and assay protocols were developed (including QA/QC issues), application of GyÆs sampling theory and its calibration, and how the data was subsequently applied to grade estimation.

Jan 1, 2005

BHP is the world's largest copper concentrate producer with production from mines at Escondida (Chile), Ok Tedi (Papua New Guinea), and Island Copper (Canada). The entire concentrate production is further processed into refined copper by third-party smelters around the world. In anticipation of an expansion in the global copper concentrate production capacity and a corresponding increase in treatment and refining charges by copper smelters, BHP has continuously evaluated various opportunities for downstream copper processing. An expansion in the Escondida mine production, combined with BHP's interest in processing some of its concentrate production on-shore in Chile, ultimately resulted in the development of the Escondida Leach Process. This process was specifically developed for higher grade concentrates, such as from Escondida. An ammoniacal lixiviant and air are used under ambient conditions to leach less than one-half of the contained copper values. After solid-liquid separation, the solution is subjected to solvent extraction regenerating the ammoniacal lixiviant and the copper loaded organic phase is stripped in spent electrolyte returned from the electrowinning plant where ultra-high quality SX-EW copper is produced. The solid leach residue can, if required, be upgraded by flotation to produce a high-grade copper concentrate with improved fuel values and a pyrite tail for disposal. After an 18-month bench and pilot plant scale program and an engineering feasibility study, Minera Escondida Limitada decided to build an 80 000 tonnes of copper per year facility near Antofagasta, Chile. The installed investment cost amounted to around $160 million. The plant went into commercial production in November 1994 and better than 99.9995 per cent Cu cathodes were produced right from the start. BHP believes that the process and the commercial plant are an excellent example of a novel approach advancing the science of copper metallurgy in harmony with present demands for environmentally sound processes and high quality products.

Jan 1, 1995

By R Benton

Since commencement of underground production in March 2006 the Kencana K1 orebody has delivered over 0.9 Mt of ore containing 1.18 Moz Au until April 2009. The Kencana deposits are part of the Gosowong goldfield located on the island of Halmahera in eastern Indonesia. The district has produced over 2.3 Moz since mining commenced in 1999 with the first two deposits extracted by open pit methods. The K1 deposit is technically challenging being a vein style deposit with poor to very poor ground conditions and a relatively low overall dip of around 45 degrees to mine grid east. It is mined under geological control by underhand cut and fill methods utilising cemented paste backfill aiming for 100 per cent extraction. With these conditions the operation was mine limited in the initial two years of production resulting in low stockpile levels for mill feed blending and hand-to-mouth mine to mill production. Mill feed rates have increased from 30 t/h to 55 t/h over this period following business improvement projects while mine production has escalated to match this increase as deeper levels of the deposit are accessed. The operation has now become mill limited. Monthly mill gold production from Kencana has ranged up to 50 000 oz with head grades ranging between 8 g/t and 122 g/t Au on a daily basis. As individual grade control assays can extend into the per cent Au range there are challenges in sampling, modelling, mining, blending and milling the Kencana orebody. At the time of commencement of ore driving in K1 the national geology team had little prior experience in underground mining and systems were in early development. The variances in feed grade and tonnages have been reduced with time as the operation evolves and business improvement initiatives are undertaken to smooth peaks and troughs in ore supply. Two such initiatives in the geology department have added over US$20 M of additional revenue per annum.

Jan 1, 2009

Over the last 100 years in the Polish mining industry considerable work has been done to assess optimum slurry, develop flexible delivery systems and adjust the fill technology to a wide variety of mining and geological conditions. Sand or industrial mineral waste materials for the backfilling of underground voids are used to control ground movement and surface deformation. This paper discusses various criteria to be considered in the preparation of a fill, including slurry properties, mine infrastructure, mining geometry, placement methods and the purpose of the backfill. This paper presents laboratory and in situ test data on the influence of materials parameters on the slurry flow in a pipeline system, stiffness, permeability, binding time and strength of a backfill, on the distribution of mixture in underground voids or the penetration between roof fall materials.

Jan 1, 1998