Search Documents

By C X. Zhang, W K. Ru, S C. Hu

To study the creep properties and the energy evolution characteristics of the weakly cemented rock (WCR) in western China, the creep deformation damage law of weakly cemented mudstone (WCM) under graded loading and the energy evolution characteristics of each creep stage were analysed based on the triaxial graded loading creep test of WCR. The results showed that as the confining pressure increased, the creep failure strength of the WCM increased from 9.5 to 24.8 MPa, and the relative displacement of the mineral particles in the mudstone increased gradually, resulting in a reduction in the fracture angle from 79.7° to 58.3°. At the same stress level, the strain energy Ue, the total energy U, and the dissipation energy Ud all increased as the confining pressure increased, but the growth rates of U and Ud decreased gradually, while the growth rate of Ue remained high. At the end of the stable creep stage, Ue increased slowly with the confining pressure, while U and Ud increased rapidly with the confining pressure, and their growth rates were basically the same. At the end of the accelerated creep stage, the growth trends of these three energies were all positively correlated with the confining pressure, Ue was significantly lower than that at the end of the stable creep stage, and Ud and U were further increased. These results revealed the unique creep properties and energy evolution characteristics of the WCR, providing a theoretical basis for long-term stability control of roadways that are built with WCR.

Nov 29, 2022

By W Y. Guo, L X. Chen, D X. Zhang

To obtain the rock type-I crack propagation process accurately, a novel fixture is used to make the prefabricated crack of rock propagation along the predetermined direction. In this study, the crack propagation process of rock is monitored with the digital image correlation method (DICM), and a mechanical model of crack directional propagation was established. The results show that the simple crack directional propagation device can effectively realise the stable propagation of type-I crack along the predetermined direction, the crack initiation angle is less than 10°, and the deviation between the peak strength of crack propagation calculated by a simplified mechanical model and the tensile strength of Brazilian splitting is 22.76 per cent and 7.53 per cent, respectively. According to the deformation field evolution law, crack propagation can be divided into three stages: microcrack development, main crack propagation, and main crack propagation. As for the rock type-I crack initiation and propagation mechanism, before reaching the peak strength, the prefabricated crack tip is subjected to maximum tensile stress; the elastic energy increases rapidly, and the dissipation energy increases slowly; after the peak strength, elastic energy exceeds its energy storage limit and released rapidly, and most of the input energy is converted into dissipation energy, which makes the crack propagation rapidly. The crack directional propagation device will be further optimised and improved, and it is expected to provide a new method for the study of crack propagation mechanism, rock failure precursor information and crack arrest principle, etc. It will also provide theoretical references for the optimisation of coal strata directional blasting, fracturing, fracture arrest, and other related technologies in geotechnical engineering.

Nov 29, 2022

By B Lyne

In 1990, the Queensland mining industry had come to the conclusion that new safety and health legislation based on risk identification and control was required if the mining industry was to be effectively and efficiently regulated. In particular stakeholders in the coal mining industry had arrived at this opinion after the industry had suffered a number of major underground explosions over the 14-year period between 1972 and 1986. Also by 1990, a general consensus had emerged across both the coal and metalliferous mining sectors that mining industry was over regulated and, more to the point this over regulation did not encourage industry to identify and address the underlying causes that had led to a cycle of major mining accidents in the state. The prevailing opinion was that the prescriptive legislation left the ownership of risk management with the regulator and not with the mine operator. This paper discusses the background to the development of the Queensland Coal Mining Safety and Health Act 1999 and the Mining and Quarrying Safety and Health Act 1999 and the progress made in improving safety and health since the statutes came into force on the 16 March 2001. The paper discusses the issues that had to be addressed during the development of the legislation including the interaction with other legislation based on based on risk management principles that either overly or interface with the mining legislation. The effect the underground explosion at Moura No 2 in 1994 had on the final content of the new legislation is also considered. Health is often the neglected twin of safety and health legislation and the paper previews the health surveillance system being proposed in Queensland to ensure that health of mine and quarry workers is afforded the same priority as their safety. By increasing the structured management of occupational health problems in our mines there is an opportunity to make significant improvements in mine safety In conclusion the paper reviews the results to date since the introduction of the new mining safety and health legislation in Queensland on the 16 March 2001. Progress has been made and more is yet to be achieved

Jan 1, 2003

By Z R. Guo, Y Qiu, X F. Wang

Mechanical damage leads to the increase of effective stress of sediments, and pore closure hinders the discharge of methane gas. Ignoring the influence of mechanical damage leads to an excessive prediction of hydrate gas production. Therefore, a fully coupled model considering mechanical damage-chemical decomposition-gas-water two-phase seepage-temperature was developed in this study, and the model was verified by Masuda experiment. Based on the fully coupled model, the temporal and spatial evolution of the whole process of hydrate decomposition under the influence of three initial absolute permeabilities, three pressure drops and three water saturations were considered. The results showed that: • The gas production rate reached the peak value in a short time after depressurisation, and the peak value increased with the increase of the absolute initial permeability. The larger the initial absolute permeability was, the faster the damage variable reached the peak value. The porosity increased gradually before the damage variable reached its peak, and the gas flowed more easily. • When the pressure drop was low, the hydrate remained stable in solid form. As the pressure drop increased, the hydrate gradually began to decompose. The greater the pressure drop was, the faster the initial decomposition rate of the hydrate was. So the damage variable increased rapidly and the porosity increased continuously, resulting in a large gas production rate at the initial stage of decomposition. • The larger the initial water saturation was, the smaller the effective stress wss, resulting in the slow growth of the damage variable and the small change of porosity.While the gas relative permeability was small, it resulted in a smaller gas production rate, and hydrate decomposition was slower. • The damage variable showed a process of rapid growth first, then slowly increased to the peak, and then gradually decreased to a stable state. When the damage was considered, the hydrate decomposition time to the steady state was longer, and the gas production was about 80.68 per cent of that without considering the damage.

Nov 29, 2022

By A Radici, S Russell

The Dampier Port Upgrade was completed in 2007 and is the largest project in Rio Tinto Iron Ore's expansion program. The project doubled Dampier Port's iron ore shipping capacity over a five year period. Sinclair Knight Merz (SKM) was appointed by Rio Tinto as the Engineering, Procurement and Construction Management (EPCM) contractor to manage Phase A and Phase B of the Dampier Port Upgrade. The aim of the project was to increase the Dampier Port capacity from 74 to 140 million tonnes per annum (Mt/a). This increase in shipping capacity tripled the capacity of the Parker Point facility from 34 to 94 Mt/a, whilst the East Intercourse Island facility increased from 40 to 46 Mt/a. The Dampier port remained fully operational throughout construction and achieved record yearly export tonnages over the period of the project. The $US1.4B project was completed ahead of schedule, on budget and with an outstanding safety record. Significantly the project team set an industry benchmark by achieving five million man-hours Lost Time Injury (LTI) free. The project has been recognised by the Engineers Australia 2008 Western Australian Engineering Excellence awards as category winner in resources and the overall winner in WA, and went on to win a National Engineering Excellence award. This paper provides an overview of the EPCM project management and an insight into some of the key drivers that have delivered this outstanding project.

Jan 1, 2009

By S M. Aminossadati, C M. Stewart, M S. Kizil

Mine ventilation models are now an accepted component of most mine management systems. However, modern ventilation models also represent a highly structured spatial data source, defining underground pathways and connections across a mine. This creates opportunities to extend the use of network models beyond ventilation design, by using critical path algorithms to find pathways such as minimum distance or minimum time.This paper explores the use of ventilation network models to automatically analyse and calculate potential emergency escape routes. A variation of Dijkstra’s algorithm is used to predict complex pathways between any two points across a model, representing an escape route from an emergency area (such as a fire) to a safe location (such as the surface or a refuge station). Weighting can be assigned to paths to represent potential travel speed, obstructions or preferred routes. Finally, emergency considerations such as smoke or gas in some parts of the mine can then be incorporated into the pathways to force the algorithm to avoid dangerous routes and specify safer pathways. Ventsim is used to visually show example results.Emergency egress pathway prediction using ventilation network models can provide an efficient way to quickly predict the quickest or most efficient escape routes for emergencies or planning purposes.CITATION:Stewart, C M, Aminossadati, S M and Kizil, M S, 2017. Emergency egress pathway prediction using ventilation models, in Proceedings Australian Mine Vent Conference 2017, pp 57–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By L Yao, J Li, C Sammut, B Li

The underground mine environment is inherently complex and hazardous, which necessitates ensuring mining workers’ safety. With the fast development of AI techniques, human activity recognition has become a crucial task to enhance daily life, especially in such challenging settings. This enables automatic monitoring and detection of the mine workers’ activities and operations on a large scale, which leads to better support of workers’ safety and welfare. Existing traditional uni-modal approaches, which use data of one single modality, suffer from low data quality and noise, so they struggle to generalise effectively in such extreme conditions (Li et al, 2022). As underground mines have extreme and complicated environments, such as dust, low light, signal interference, and rugged terrain, uni-modal approaches could not resolve such obstacles and are not suitable for real-world deployment. Multi-modal human activity recognition approaches could use data from multi-modal sources, thus capturing complementary information and producing robust and effective performance in recognising and monitoring mining activities. In this case, designing suitable multi-sensor hardware and AI activity recognition models has become a pivotal task. Producing efficient multi-modal approaches for edge deployment is another problem worth exploring.

Sep 1, 2024

By Wright D. J

Successful heap leaching depends on three major factors: 1. Chemical conditions appropriate for the dissolution of the valuable metal; 2. Contact between the leach solution and the valuable metal particles; and 3. Movement of the leach solution through, and out of, the heap. Given that appropriate chemical conditions can be provided, and the individual particles have sufficient permeability to allow solute/solvent contact, the problem of getting the solution to and from the particles remains. Non-uniform percolation of solution throughout the heap, caused by the presence of fines, is a common problem which occurs, to some extent, with all heap leachable ore. The conventional solution to this problem is agglomeration, which involves the attachment of fine particles to larger particles, effectively modifying the size distribution by preventing the fine particles from acting on their own. While agglomeration must be considered as an extremely effective technique with virtually no limit to its application from a technical point of view, its application is limited by economic considerations. A new technique has been developed which is not only a low cost alternative to agglomeration, but also has the potential for enabling the application of low cost heap and vat leach techniques to a significantly wider range of ores than current practice would suggest. The new technique, known as Electrokinetic Leaching, utilises electro-osmotic flow to enhance percolation through the heap. This paper describes and presents results of the laboratory testing, pilot heap operation and commercial application of Electrokinetic Leaching of a low grade gold ore and a tailings deposit. Comparative cost analyses between conventional and the alternative processing techniques are presented.

Jan 1, 1994

The Pilbara region, located in the north-west of Western Australia, is significant as the second-largest source of iron ore on the planet. Iron ore mines owned and operated by Pilbara Iron are located within the Hamersley Basin. This paper refers to the Greater Paraburdoo mines, the 4WEST and 4EAST pits, located on the southern margin of the Hamersley Basin. The groundwater model refers to ephemeral watercourses: Seven Mile and Pirraburdoo creeks, which are adjacent to the two pits, and Ratty Springs, located upstream from 4WEST and within Pirraburdoo creek. The spring and creeks hold cultural heritage significance for local Aboriginal communities. Two of these, the Gobawarrah Minduarra Yinhawanga (GMY) and Innawonga native title claim groups, initiated hydrological work on the two creeks and Ratty Springs, with the aim of determining the affects of dewatering on the natural water flows of these systems. The numerical model used to simulate drawdown in the Pirraburdoo and Seven Mile Creeks was derived from PMWIN Pro software and covered an area of 77 km2. The modelling period was from January 1998 to December 2004, and the prediction period was from January 2005 to December 2015. The model has four layers and incorporated effects caused by mining voids, 4WEST and 4EAST pits, creek bed material, weathered bedrock below creeks and surrounding banded iron formations (BIF). The model has been calibrated using the trial-and-error method set down by Middelmis et al (2001). The current dewatering schedule (12 ML/day) in the 4WEST and 4EAST mining areas does not affect the water table levels in the adjacent creeks significantly or for any considerable periods of time. However, changes to mine plans may occur, for example, in response to changed commodity price and may lead to significant increase in rates of vertical advancement. This, in turn, affects dewatering schedules, as greater vertical advancement requires increased dewatering effort. When an accelerated mine plan is applied to the model and dewatering rates increased to 18 ML/day, drawdowns in the creeks are more noticeable. The model has therefore helped to indicate the extent to which increased dewatering rates may be acceptable, especially in terms of immediate and longer-term damage to riparian species, ie Melaleuca and Eucalypt. Predictions from the model may also allow mine planners to schedule decreased rates of vertical advancement, where these are required to meet environmental constraints.

Jan 1, 2006

By J M. F Clout

The low-grade clay-rich -1.0 mm fraction of fine iron ores have often proved difficult to upgrade and capital intensive to process when using traditional wet beneficiation technology including single or two stage hydrocyclone desliming, wet high intensity magnetic separation (WHIMS), spirals and final dewatering using fine screens. Very fine (<0.010 mm) clay-rich slimes simply follow the water split to the hydrocyclone underflow where it often impedes the subsequent processing performance of any downstream spirals and can result in troublesome direct dewatering of hydrocyclone underflow. The -1.0 mm fraction in goethitic iron ores is typically considered as waste. A new two-stage wet gravity separation flow sheet, referred to as the ædesandÆ process, has been designed to overcome these issues for the upgrading of low-grade clay-rich goethitic or hematite-quartz fine iron ores. The desand process is designed to treat the -1.0 mm range from -8.0 mm natural fines, to recover a -1.0 +0.038 mm higher-grade fraction by rejecting to tailings any low-grade clay-rich ultrafines and low density sand-size fine chert/quartz gangue and shale.The desand process consists of wet screens with a nominal 0.7-1.0 mm cut point which direct the undersize to hydrocyclones. The hydrocyclone underflow is then fed to upcurrent classifiers where the classifier middlings is sent to spirals and classifier and spirals concentrates are then dewatered using vacuum belt filters or fine screens. The three product upcurrent classifier is employed to further deslime the hydrocyclone underflow, producing firstly a coarse final concentrate, and then a deslimed middlings for feeding to spirals as well as a 0.100 mm clay and fine quartz or banded iron formation (BIF) sand in final overflow for feeding to the residue thickener. The upcurrent classifier middlings provides the spirals with a significantly cleaner feed material than traditional methods, with the end result that the spirals do not silt up with slimes and therefore can continue to run at their optimum. The upcurrent classifier and spirals form a complimentary pair, with the upcurrent classifier better able to send coarser, acceptable grade particles to concentrate and fine slimes to tailings whilst allowing the spiral to better reject coarser, subgrade low specific gravity particles. Test results for the Mayoko-Moussondji iron project, Republic of Congo, using upcurrent classifier-Wilfley Table (simulating spirals) gave acceptable mass recovery from run-of-mine (ROM) and Fe recovery from hydrocyclone underflow for HEMCOL (6.2 per cent mass recovery from ROM/43.1 per cent Fe recovery) and HEMBIF2 (5.1 per cent mass recovery from ROM/22.3 per cent Fe recovery) mineralisation types. The desand process also enables improved dewatering of -1.0 +0.038 mm product from a clay-rich plant feed.A number of new wet plants in the Pilbara use the desand flow sheet including FMGÆs Cloudbreak and their two Christmas Creek plants. Many potential new applications are being explored, with new iron ore plants in India as well as those being proposed for West Africa. Operational experience has highlighted the importance of providing clean process water to the upcurrent classifiers as well as ongoing design improvements including increased wear life, reduced maintenance and enabling a more steady feed rate to spirals.CITATION:Clout, J M F, 2013. Beneficiation of fine iron ores using the desand process, in Proceedings Iron Ore 2013 , pp 337-348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By E S. B Santiago, C P. N Moreto, L V. S Monteiro, G H. C Melo, R P. Xavier

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Iron oxide-copper-gold (IOCG) systems of the Carajás mineral province (Amazon craton, Brazil) are structurally controlled by regional-scale shear zones and have formed by multiple episodes of fluid circulation and hydrothermal alteration in the Neoarchean (2.71–2.68 Ga and 2.56 Ga) and Palaeoproterozoic (1.90–1.87 Ga).Collectively, fluid inclusion, boron, oxygen and hydrogen isotope data and Cl/Br–Na/Cl ratios in fluid inclusions reveal that regional circulation of non-magmatic brines (eg evaporative fluids/evolved sea water) and mixing with other fluid sources (eg meteoric or magmatic) is an important attribute in the genesis of the Carajás IOCG systems. The ?33S and d34S compositions of sulfides from the Neoarchean and Palaeoproterozoic IOCG systems suggest that the ore-bearing fluids have assimilated sulfur from crustal reservoirs. Nevertheless, most ?33S measurements have indicated mass independent fractionation (MIF) effect for both systems which points to the possible involvement of surface sulfur sources.CITATION:Xavier, R P, Monteiro, L V S, Moreto, C P N, Melo, G H C and Santiago, E S B, 2015. Non-magmatic versus magmatic fluids in the genesis of Archean and Palaeoproterozoic iron oxide-copper-gold systems of the Carajás Mineral Province (Brazil), in Proceedings PACRIM 2015 Congress, pp 281–288 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Howell M. W

The purpose of this paper is to outline the main points in the construction of the various types of wire ropes more commonly used for winding in Australia; and the maintenance of the ropes, and cage and skip safety gear as practised at the South mine, Broken Hill.It should be mentioned that both of the shafts at present in use are dry, and both downcast with or without the assistance of the two exhaust fans normally in use: Night shift and week.-end overtime are practicaly non-existent.Thus, during night shift, the cages in No. 7 shaft are landed on the chairs at the surface, providing efficient covers for the· shaft, and allowing the maximum amount of rope to be wound on to the drums. This also applies to the cages of both No. 7 and No. 4 shafts during the week-ends.These factors, combined with electric winding and skip haulage, are calculated to obtain the best use of the ropes when properly attended.WINDING ROPES-TYPE AND CONSTRUCTIONThese ropes may be divided into four main types which will include the more commonly used constructions(a) One-size strand.(b) Warrington strand.(c) Flattened strand.(d) Locked coil.1. One-size strand as the name implies, is a rope the strands of which are constructed 9f wire of the one size.Usually the strands are of 7, 19 or 37 wires.

Jan 1, 1940

By D McKeon

In July 2006, ten Mining Engineering students and Associate Professor David Laurence from the University of New South Wales (UNSW) participated in the universityÆs inaugural overseas mining field trip. The ten-day trip to western Canada involved visits to two mines in British Columbia, the Diavik Diamond Mine in the Northwest Territories and the Syncrude oil sands operation in Alberta. Importantly, the groupÆs main objective was to gain a global understanding of todayÆs mining industry by observing the different cultural, legal, social and environmental setting found in Canada. It should be noted that the entire trip was planned, organised and directed by the students and benefited from extensive industry support both in Australia and Canada. This report intends to provide an overview of the field trip and describe to a limited extent the Canadian approach to mining.

Jan 1, 2007

By Paine G. G

The Red Dome Gold/Copper Mine is located approximately 15 km west of the township of Chillagoe which itself is approximately 220 km by road west of Cairns, Far North Queensland. The deposit, with other mines in the Mungana region, was worked from about 1901 to 1927. Exploration by Amoco Minerals Australia in the 1970s and early 1980s outlined a geological resource of 15 million tonnes. A mining reserve of 9.3 million tonnes was identified and originally developed by Elders Resources Limited. The mine commenced operations in March 1986 and was the first large-scale gold project in Australia to be developed solely on the heap leach process. The mine operated successfully as a gold heap leach operation until 1989 when new grinding, flotation and carbon-in-leach plant facilities were installed to process the non heap-leachable component of the orebody including the copper rich -ore. In March 1991, Red Dome Pty Ltd became a wholly owned subsidiary of Niugini Mining Limited. After six years of successful operation and having excavated a 200 in deep pit, it became evident in 1992 that unless more open cut reserves could be identified the operation was limited to six to nine months of high grade ore and a further 15 months of low grade stockpile material. A preliminary feasibility study was carried out to assess the viability of deepening the open cut. This indicated that from a technical and financial point of view it was possible to expand and deepen the open cut. This presented the daunting challenge of developing a 300 in deep, single access, open cut between a high chert ridge, a government railway line and a National Park. The meeting of this challenge is the subject of this paper.

Jan 1, 1994

By B P. Banerjee, S Raval

In the recent past there have been dramatic advancements in the development of remote sensing platforms (satellite, aircraft and unmanned aerial vehicles – UAVs) as well as sensor systems (multispectral, hyperspectral, thermal, light detection and ranging (LiDAR) and radar). However, selection of the appropriate remote sensing technique for a mining application is complex and requires scrutiny on multiple scales including spatial, temporal and imaging capabilities. This presentation highlights various conventional and emerging remote sensing approaches over a mine’s life.CITATION:Banerjee, B P and Raval, S, 2016. Applications of advanced remote sensing systems during a mine life, in Proceedings Life-of-Mine 2016 Conference , pp 116–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By G McCullough, B Mutsaers, J Jessop

"*This is an abstract only* Geometallurgical initiatives have demonstrated considerable value to operations that have trialled them. However, it is extremely difficult for these initiatives to become properly embedded into the operations and for that value to be realised on an ongoing basis.This paper will explore some of the historical reasons why this is the case. Some of these reasons include the limited tools available to manage an integrated operation. These, in turn, have resulted from poor communications infrastructure, inadequate sensor capability and the way technical mining software has evolved over the last 30 years.This paper will then investigate how the evolution of technology in recent years can help overcome these constraints and compare progress with similar industries.CITATION:McCullough, G, Mutsaers, B and Jessop, J, 2013. Obstacles to embedding geometallurgy decision-making into operations and how to increase maturity of this critical capability, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 139-140 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By P J. Bangerter, J Pan

Optimising for Net Present Value (NPV) with a strategic optimiser such as COMET, Prober-E, Blaser or Minemax has hitherto lacked a dynamic method for analysing the so-called third-order outcomes (such as Carbon emissions) of optimisation within life-of-mine planning. Optimisation, per se, has natural effects on carbon emissions in a life-of-mine plan. Contemporary strategic planning employs a mathematical optimiser to make sense of non-linear data (ie a block model) and produces a best-NPV optimised mining schedule, within a set of constraints. The very act of optimisation influences emissions, and in a dynamic way.

Aug 2, 2023

By L E. Setiawan

The mining and milling groups at Batu Hijau are tasked with increasing SAG mill throughput by approximately ten per cent. Avenues used for this process are blasting and crushing optimisation, ore blending and predicting SAG mill throughput in relation to the geological model. This is in line with traditional æMine to MillÆ studies. At Batu Hijau, mill and mine sequencing cannot readily be configured to perform the surveys traditionally required by a æMine to MillÆ study while meeting the daily production target of 140 000 tonnes per day and processing from varying ore types in one pit. A program called BOCCOST (blasting optimisation crushing conveying optimising SAG throughput) has been implemented to capture approximately 200 variables from blasting, mining and milling operations and assign them to a common point in space in the geological model in real time. Interpretive analysis of data from BOCCOST is used to model relationships between the 200 variables to determine which and how these factors affect SAG throughput. Once these relationships are determined, the blasting, ore blending and crushing process can be optimised to generate a product that maximises mill throughput. The relationships modelled from BOCCOST are also used to generate a SAG mill throughput estimator, which can be coded into the production block model. The block model can be reconciled with the geological block model for correlation by geological domain. Once this relationship is established, SAG mill throughput domains can then be established for predicting SAG mill throughput. This SAG mill throughput estimator is then used in conjunction with revenue calculations to determine an ore cut-off, which combines these two elements to maximise metal production.

Jan 1, 2002

By F Shi, G Ballantyne, K Runge

There has been minimal innovation in the methods used to process an ore over the last 50 years. Productivity increases have largely resulted in increased equipment size without implementation of parallel improvements in technology. Complex orebodies of the future will need mining operations to adopt new technologies and techniques to make future ore treatment economically viable. Three emerging technologies, namely high voltage pulse (HVP) pretreatment, fine screening and the HydroFloat<sub>TM</sub> coarse particle flotation cell will be presented in this paper and the potential benefits that may result if they are adopted in mineral processing circuits will be outlined. The barriers that must be overcome before they can be adopted by industry with confidence will also be discussed. CITATION: Runge, K, Shi, F and Ballantyne, G, 2018. New technologies that will potentially enable processing of complex orebodies, in Proceedings Complex Orebodies Conference 2018, pp 126–129 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By L Huang

"Successful rehabilitation of tailings landforms of tens to thousands of hectares in size at base metal mines is critical to mining companies’ ‘social licence to operate’. Rehabilitation technology used is closely related to both the economic sustainability of the mining company and the ecological sustainability of the mined environment. Conventional technology to rehabilitate mine waste landforms is costly and constrained by the availability of soil (to reconstruct root zones) and clay materials (to reconstruct compressed layer). Depending on mine waste properties and site-specific resource availability, it is not uncommon to cost A$0.1–0.5 M/ha for the establishment of conventional cover systems over mine waste domains, which often accounts for large proportion of the total closure costs. This can lead to costs approaching several hundred millions dollars for rehabilitating larger tailings and acidic waste rock using conventional cover systems.The present extended abstract proposes a suite of new technologies to tackle the problems outlined above and discusses critical factors in successful rehabilitation from substrate levels to the whole landform performance, in two key aspects:in situ engineering of tailings soil to offset/reduce materials requiredin situ chemical engineering of massive hardpan layer through alkali-activation and mineral gel cross-linking network mechanisms to encapsulate reactive tailings and achieving sustainable hydro-geochemical stability in root zones.This aims at functionally replacing the roles of the compressed clay layer and capillary breaks in conventional covers. These technologies would improve both the economic and ecological sustainability of mine waste rehabilitation, thus addressing the triple-bottom line of mining and mineral processing industries not only in Australia but other countries.CITATION:Huang, L, 2016. Emerging technology for economic and ecological sustainability in the rehabilitation of metal mine tailings, in Proceedings Life-of-Mine 2016 Conference, pp 128–131 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016