Search Documents

By R M. Yanamandra, S K. Tripathy, N Mangadoddy, P Sudikondala, P Ankireddy

Spiral concentrator is one of the most commonly used gravity concentration devices in mineral processing. The particles are classified based on their specific gravity and size. The present work analyses the experimental and numerical investigations of the water flow field, such as fluid depth and free surface primary velocity of two high gravity spiral concentrators at different flow rates. The measurement techniques use a flow depth gauge and flow visualisation technique adapting lycopodium powder as the tracer. Flow features in terms of liquid depth and primary velocity at the free surface of the flow are captured across the trough in two different high gravity spirals. A highspeed motion camera with an imaging frequency of 5400 frames per second and 768 × 768 pixel resolution is utilised to track the tracer particles in the liquid flow on the dark surface background. Further, the two-phase flow is studied numerically on high gravity spirals based on the volume of fluid (VOF) approach utilising the RNG k-ε model and Reynolds Stress Model (RSM) for predicting the fluid flow on trough surfaces such as water depth and free surface primary velocity. The CFD predictions of the flow field for the two spirals are attempted to validate against experimental data. The high gravity spiral concentrators show lower flow depths and free surface primary velocities but steep velocities on the outer trough zone compared to that of low gravity spiral concentrators (conventional coal spirals). Among the computationally tested high gravity spirals, higher pitch and higher secondary slope design shows greater flow characteristics.

Aug 24, 2022

By M Titley, M NoppT

A study on the feasibility of mining the recently discovered Wallaby gold deposit is due for completion by mid-2000. Open pit mining is the favoured method. Determination of the impact of mining bench height on the recovery of ore, including the estimation of dilution and ore loss, is critical to the economics of the operation. Conditional simulation was used to derive a number of gold estimation scenarios within a typical volume of the deposit. These scenarios were interrogated for a selection of mining bench heights and ore block dimensions. The results were reported as a range of grade tonnage relationships and compared to the kriged resource model. This allowed the resource model to be calibrated to a specific mining bench height and ore block size. Once calibrated, more realistic dilution and ore loss values for a number of mining bench heights were calculated from the resource model. These values were then used to determine the economic sensitivity of particular mining methods. The spread of results from the simulations also provided an indication of the confidence in the kriged grade estimates for the different zones of mineralisation within the deposit and highlighted areas of any significant uncertainty.

Jan 1, 2000

By H Indirawati, R Ayres, A Nur Kasnanto, S Konopa

As a project moves through the mine life cycle, the quantity of data available increases and the understanding of the orebody matures. Incorporating new information quickly and efficiently in current 3D models, is essential for adding value across the life-of-mine value chain. At the Martabe Gold Mine, the resource development group manages 14 drill rigs on six resource projects, including three operating mines. The Martabe deposits are geologically complex and the volume of new information that becomes available each day is substantial. It is imperative that new geological and assay information is integrated into the 3D models as soon as possible, so that drill planning and targeting can be modified accordingly. Martabe uses Leapfrog<sup>®</sup> 3D software to update and interrogate the 3D models on a dynamic basis as data becomes available. This results in faster and more effective changes to drill planning and schedules. The impact of this is better drill productivity and cost savings due to optimal drill targeting, and availability of up-to-date models incorporating the most current data. CITATION: Konopa, S, Ayres, R, Nur Kasnanto, A and Indirawati, H, 2018. Optimised drill targeting using dynamic 3D modelling, Martabe Gold Mine, Indonesia, in Proceedings Complex Orebodies Conference 2018, pp 99–101 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By Skinner W, Netting A. K O

Surface analysis of ore samples collected from corresponding concentrate and tailings process streams is now a widely used tool in many Australian base metal sulphide concentrators, particularly those involved in AMIRA projects. The use of tec

Jan 1, 1997

By J Pearse, N Acosta, N McIntyre, M Angarita, L Camacho, C Huguet, D Arbelaez-Ruiz, J Ossa-Moreno, O Restrepo

Colombia is an example of a nation where mining makes a significant contribution to local and national economies. Due to the abundant resources present in the ground, there are good prospects for further development. However, the impacts of mining projects can include reduced access to good quality freshwater for other economic activities and/or biodiversity preservation (Ossa et al., 2018). As well as the water management challenges common to all mining regions globally, Colombia has particular challenges associated with its biophysical and socio-political traits. Land use change in many regions is dynamic including rapid development of agriculture and the development and abandonment of small scale mines. The value of ecosystem services provided by prospective mining regions also creates challenges in particular with regard to the páramos, the headwater wetlands from which about 70% of Colombia’s water supply has originated (Cleef 1981). Colombia also has particular challenges related to strong preconceptions about mining and its impacts on water. On the one hand, there is recognition that new large-scale mines are important for Colombia’s economy; on the other, there is deep distrust of the sector’s ability to operate with minimal adverse impacts (Gutiérrez-Gómez, 2017). Hence, any impact assessment is likely to face high levels of scepticism and scrutiny. Summarising the work of McIntyre et al. (2018), this abstract proposes a framework for assessing and communicating risks to regional water resources arising from the impacts of mines. The framework outputs aim to provide government and other stakeholder groups the scientific evidence needed to inform their viewpoints about mining development in the selected region, and a baseline from which to design a program of priority scientific research. CITATION:McIntyre, N, Angarita, M, Acosta, N, Camacho, L, Pearse, J, Huguet, C, Restrepo, O, Ossa-Moreno, J and Arbelaez-Ruiz, D, 2018. A framework for assessing and communicating water risks in prospective mining regions of Colombia, in Proceedings Life-of-Mine 2018, pp 49–51 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Gemmell J. B

Zinc-bearing massive sulphide deposits have been mined in Tasmania since 1900. The current major producers are Hellyer and Rosebery, with total resource tonnages (mined plus reserves) of 16 Mt (million tonnes) and 24.8 Mt respectively. These deposits belong to the class of seafloor volcanic-hosted massive sulphides (VHMS) and are located within the Mt Read Volcanics, a narrow belt of continental margin calcalkaline volcanics of Cambrian age. Compared to other Australian VHMS deposits, and world-wide MVT and Sedex deposits, the Tasmanian examples clearly stand-out due to their high metal grades, averaging over 17 per cent Pb+Zn. The deposits vary in morphology from mound style (Hellyer) to sheet style (Rosebery) with other combinations including stacked lenses (Que River) and disrupted cross-cutting bodies (Hercules). All deposits show the classic VHMS zonation from an Fe-Cu-bearing base to a Zn-Pb-Ba-rich top. Zinc, gold and silver tenor commonly increases toward the stratigraphic top of the deposits. The ores have been deformed during regional metamorphism, resulting in folding, shearing and recrystallisation of sulphide lenses. In addition to the major deposits, a number of small massive sulphide prospects occur throughout the volcanic belt and the potential for the discovery of further large, deeply buried deposits remains high.

Jan 1, 1993

By M I. Pownceby, J Manuel, S Suthers, A Poliakov, E Donskoi, N Ware

"The mining industry is constantly seeking methods for optimising the exploitation of mineral resources, such as iron ore, in a sustainable and eco-efficient manner for economic and social benefit. When faced with resources that have mineralogical or textural complexity, poorer grades or geological variability, it is particularly important to apply a comprehensive geometallurgical approach to the development of the mining operation, from resource definition through to processed product. Integral to this approach is the quantitative characterisation of representative samples across the whole orebody.A key factor that associates the geological characteristics of iron ores to their processing response is ore texture. While the classification of samples on the basis of chemical or physical properties alone is often not sufficient to predict their processing behaviour, classification and quantification of texture types can be effectively correlated to metallurgical performance in processes such as blending, beneficiation, pellet making, sintering and ironmaking. This paper describes some of the research conducted by CSIRO pertaining to the design and rationale of a texture-based classification system for Australian iron ores; some of the tools developed and used to apply such classification; and the application of the generated data to quantifying, modelling and predicting sintering behaviour and performance in the blast furnace.CITATION:Suthers, S, Pownceby, M I, Manuel, J, Ware, N, Donskoi, E and Poliakov, A, 2016. Geometallurgical Characterisation of Australian Iron Ores – from Ore to Processed Product, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 351–360 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By A McCallum, J Abols, G Patrick, G Johansen

The authors challenge the traditional thinking that whole ore cyanidation followed by Carbon in Pulp (CIP) or Carbon in Leach (CIL) should be applied as a standard process in the majority of gold processing flow sheets. The concept of whole ore leaching by using cyanide can result in unnecessary environmental and capital risk. Alternative, currently available technologies can be used to provide the desired level of gold recovery at a much lower installed cost and less impact on the environment. Gravity concentration, alone or in conjunction with flotation, can produce a gold bearing concentrate that can then be fed directly to a batch or continuous intensive cyanidation unit. The In-line Leach Reactor (ILR) is an intensive cyanidation unit developed by Gekko Systems of Australia. Advantages of this technology include significantly reduced capital outlays for greenfield plants or plant upgrades and increased investor returns. Reduction of onsite cyanide and carbon inventories improves plant safety, materials handling and site security. By using direct electrowinning to treat the gold bearing solutions produced by the ILR, the need for a conventional carbon stripping circuit is removed. Potential also exists to increase grind size û saving energy, further reducing capital and operating costs and decreasing the environmental impact of a mill. Detoxification of cyanide before the release of solution to the tailings dam can minimise tailings disposal and containment requirements. When used in the right application the proposed process will have little or no impact on gold recovery and may actually increase recovery for complex ores. Areas applicable to this type of treatment include: plants in environmentally sensitive regions, lower tonnage higher grade deposits, coarse gold deposits, and preg robbing ores û some of which may not currently be economically feasible using standard processes and flow sheets. We have provided two examples of such projects, where an alternative to whole ore leach and CIP or CIL has the potential to deliver these benefits.

Jan 1, 2004

By E Williams

The role and importance of a well designed test work program during the development of an orebody is often underestimated. A test work program should be tailored to deliver very specific answers to relevant questions. With a clear purpose, the results from the test work program will enhance the outcome of the feasibility study and provide the information required to meet the requirements of all stakeholders. With regard to test work programs there are three main areas that should be considered: orebody characterisation and definition, process flow sheet development and engineering design information.Orebody definition relies on reliable analytical methods to characterise and assess the economic minerals present in the ground. In mineral sands, the physical processing characteristics of the minerals play a significant role in the definition of an orebody. The analytical method therefore has to be customised using a combination of laboratory techniques. These techniques can include heavy liquid separation, gravity separation and magnetic separation and are usually combined with chemical and mineralogical analyses to create a picture of the orebody. During the definition phase of test work programs, an appropriate analytical technique has to be developed to evaluate drilling samples, but also to support the information collected during flow sheet development.Process flow sheet development is usually done once there is a reasonable understanding of the size and variability of the orebody. Selecting the best sample for test work is critical, as any flow sheet design is tied to the specific characteristics of the sample used for development. There are other factors that can improve the outcomes of flow sheet development test work, including the skills and knowledge of the operator and allowing sufficient time to process and analyse the results. Very often this work is conducted under pressure with limited time and resources, only to result in a suboptimal flow sheet. During this phase of flow sheet test work, iterative testing will provide the information required to develop an optimal metallurgical flow sheet. The data collected will provide indicative recoveries and yields that are required for feasibility studies.Equipment specification is often included as part of process flow sheet development. This includes comparative test work between different equipment suppliers, assessment of operating conditions such as the loading to determine the number of processing units required, as well as other design information required such as particle size distributions, density and operating temperatures.While restricting the time and costs expended on test work programs may seem to meet a short term need to meet investor requirements, neglecting to develop a proper framework of the requirements that has to be met in the long-term can lead to significant long-term cost overruns. This is mainly due to a need to repeat test work, or do confirmation test work, as insufficient information was collected during the initial program.

Oct 5, 2011

By P T. Stoker, A Allman, D P. Carville

Classification of mineral resource estimates is one of the most important responsibilities of the Competent Person. In recent years, classification decisions have been driven more by the detailed block-by-block attributes generated by the now widely applied geostatistical estimation methods, and less by a general geological overview. This is increasingly resulting in æspotted dogÆ outputs, in which blocks of Inferred Resources or unclassified material separate blocks of Measured and/or Indicated Resources, or individual drill holes are surrounded by annuli of Measured and Indicated Resource blocks. Not only are such outputs potentially misleading, since they ignore fundamentals such as continuity of geology and mineralisation between drill holes and the imprecise nature of resource estimation, they can also cause substantial problems for engineers undertaking mine designs and estimating ore reserves, particularly for underground mines. Competent Persons for mineral resources must keep in mind the purpose of their work, and should use their experience and judgement to avoid or smooth out æspotted dogÆ classifications, providing a result commensurate with the level of geological and resource estimation confidence. For their part, ore reserve Competent Persons must understand the resource estimation and classification process, and should question resource classifications that are not consistent with the level of geological and resource estimation confidence.

Jan 1, 2006

By B T. Qin, C Zhu, Y W. Jia, Y Lu, F L. Li, Q L. Shi

Air leakage through rock fractures in coal mining is a major cause of coal spontaneous combustion. In order to overcome the deficiency of the existing fire control technology and prevent coal spontaneous combustion by isolating coal from oxygen, the article proposes a novel technology of inorganic solidified foam (ISF) with high expansion to fill fractures effectively. ISF consists of fly ash, cement, setting accelerator, redispersible polymer powder, water and aqueous foam. For preparing homogeneous and stable ISF, a preparation system with a pore type foam generator, a mixer device installed with a hollow shaft and helical blades, air compressor, slush pump and monitoring instruments was developed, and the working principles of key devices were elucidated. Based on a series of experiments on the different ratios of each component material and technological parameters of the preparation system, ISF with a foam expansion ratio of 8~10 and dry density of 250–400 kg/m3 was prepared. The relationship between elastic compressive strength, modulus of elasticity and density was summarised. Based on the injection experiment for fracture of loose coal pile with high temperature, the characteristics of sealing air leakage, compressive strength, thermal insulation, flow and cooling of ISF in the fresh state were investigated, indicating that ISF can effectively cut off the air leakage and cover the coal sample to reduce the temperature in the earlier stage, and ISF can remain stable and not crack. The ISF was applied to Luwa coalmine to seal small coal pillar pressure fractures and loose coal fractures in goaf. After press-casting the ISF in Luwa coalmine, the pressure-difference of inner-outer increased, meaning the effect of external conditions on the pressure-difference decreased, showing that it could plug the air leakage effectively.CITATION:Qin, B T, Shi, Q L, Lu, Y, Zhu, C, Li, F L and Jia, Y W, 2015. The novel technology of inorganic solidified foam with high expansion for preventing coal spontaneous combustion, in Proceedings The Australian Mine Ventilation Conference, pp 121–126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By B Oostendorp, R van der Merwe, P

In order to assess whether polysaccharide depressants are strongly or weakly and reversibly bound to the surface of talc, a series of experiments was conducted on New York talc in which the floatability of the talc in a microflotation cell was determined. The talc was conditioned in solutions of carboxymethyl cellulose (CMC) or guar gum in 10-2 ionic strength Ca(NO3)2 or Mg(NO3)2. The talc was then washed with four successive aliquots of water, or cation solution, to try to remove the polymer and the flotation response of the talc was assessed. CMCs of different charge (DS) were used to assess the effect of charge on the strength of bonding. The results show that CMC and guar gum could be removed to a large extent from the talc surface by washing with water (the floatability was restored), however very little could be removed from the surface by washing with cation solution. The higher charge CMC was easier to remove from the talc planes in the absence of cations than the lower charge CMC. Thus CMC bonding to talc has been shown to be irreversible or very slowly reversible only if cations are present, implying that cations are necessary to keep the polymer bound to the surface of the planes to effect depression. The presence of ions in solution also had the effect of maintaining surface coverage of the talc by guar gum.

Jan 1, 2005

By H Kurth, L Balzan

The potential for bulk diversion was identified and quickly implemented following the development of bulk sensing technologies applied to conveyed flows. In the early 1980s real time analysis of ash in coal was intended to improve the understanding and control of quality variability. By the end of the 1980s approximately 5% of coal analysers installed were being utilised for bulk sorting; diverting flows to create stockpiles to improve blending flexibility and boiler feed consistency, diverting waste material, or bypassing the beneficiation process when the coal met product quality criteria. In the 1990s bulk sensing and sorting utilising natural gamma detection was applied to conveyed waste in gold-uranium mineralisation and allowed ore to be recovered and processed that would otherwise have been discarded. Further applications developed in the iron ore sector where product quality ore could be diverted to bypass beneficiation and save significant unnecessary processing costs and improve recovery by avoiding process inefficiency losses. Plant capacity was freed up to be utilised by material that required processing. Similar benefits became evident in the phosphate industry and in base metals where multi-elemental analysis using Prompt Gamma Neutron Activation Analysis provides ideal opportunities to representatively measure 30 second conveyed increments at high accuracies. This has been successfully adopted in copper, nickel, platinum and lead-zinc to improve waste removal after primary crushing to eliminate unnecessary expense and improve plant efficiency. The benefits include increased output from existing operating capacity, significant reductions in consumable costs and generation of fewer detrimental waste streams. The paper outlines the technologies and discusses case studies covering the above commodities, demonstrating the immense value that representative real time measurement of conveyed flows can create. Measurement data concurrently provides multiple benefits in operational performance besides sorting, through ore reconciliation, ore blending, feedforward control and metal accounting, adding further value.

Nov 10, 2020

By A Purton, C Taylor, E Conroy

The spatial modelling of geometallurgical domains is an important step in the characterisation of an ore deposit allowing for the quantification of various rock types, their differing rock properties and the overall value of a project. The traditional approach to modelling such features is through the use of deterministic models, where a single estimate of the extents and structure of the ore deposit is mapped out by geologists based on available data and their interpretation of the geological processes. Any uncertainty in the layout of different domains is not accounted for and heterogeneities of chemical and physical properties of the orebody are likely underestimated. Spatial machine learning techniques can be used to derive geometallurgical categories, or classes, from multiscale, multiresolution and high dimensional measured rock properties. Subsequently, geostatistical simulations of these classes can be applied to obtain multiple equiprobable realisations that define the layout of the geometallurgical classes at unknown locations between boreholes, or domains. In-turn these realisations can be used quantify the uncertainties in the location of boundaries between different domains. The development of a workflow for defining geometallurgical domains and later geostatistically simulating them across the Orebody H; a complex stratabound Bedded Iron Ore deposit located in Western Australia’s Pilbara region is demonstrated. This could be used to identify zones of high uncertainty where collection of additional data might help mitigate or minimise risks and in turn improve forecast production performances.

Mar 22, 2022

By S Azam

Coal is a vital energy source and source of carbon for metallurgical applications, contributing significantly to the world economy. Coal mining and processing involve multiple processes that generate Respirable Coal Mine Dust (RCMD), one of the primary sources of health hazards for coal workers. Since 2000, the rate of Coal Workers’ Pneumoconiosis (CWP) has continually increased in the U.S, with severity of the cases also worsening. Increasing evidence shows that exposure to RCMD in coal workers is a high-risk factor for lung cancer, which causes more deaths than the following three major cancers combined in the US Recent observations show an increased incidenceof CWP or other lung diseases, particularly among young miners in the Appalachian basin. The CWP prevalence in Appalachia is four times higher than the national average. Although various regulations are in place, the resurgence of such disease among coalminers demands additional efforts to better understand all the possible facets of coal dust toxicity, taking insights from current interdisciplinaryresearch efforts. One such important field is the interaction of coal dust with moisture in underground mines. Although moisture is prevalent and dynamic in an underground mining environment, it has never been evaluated for its impact on modifying the toxicity of coal dust and transport or flow behaviour. However, research conducted in atmospheric sciences in the past decade makes it clear that moisture in the atmosphere can significantly alter the behaviour of mineral dust. This paper is a part of research aimed at understanding how moisture interacts and alters the characteristics of coal dust. Such insight is crucial in understanding the potential toxicity of coal dust and developing mitigation technologies.

Oct 12, 2022

By Watters R

Modem open cut and underground mining in the tropics inevitably expose partially weathered and unweathered rocks to oxygen and water, leading to weathering and the release of solutes and often acidity as well. Historical monitoring data can demonstrate these phenomena. Three case studies from open cut mines in the north of the Northern Territory illustrate the deterioration in quality of pond water receiving drainage from waste rock dumps. The potential for deterioration of water quality was not recognised in many mine Environmental Impact Statements prepared and accepted in the 1980s. The examples documented indicate the importance of adequately planning for this near inevitable process. Retrofitting a mine water management system to 'no' or minimal release can be very difficult and expensive, and may not be feasible, leading to downstream pollution. The characterisation of acid and solute production potential of ore and waste rock, and improved dumping strategies and water management are very important to minimise the environmental impact of mining in the tropics.

Jan 1, 1994

By S Munn

Today, it can be said that the majority of mines utilise communications equipment in one form or another. Either for communications between staff making their day-to-day operations more efficient, or for emergency communications, as well as linking computer based mine management systems, and providing remote control over complex mobile and fixed machinery. With the advances in technology now available, we are moving into the next generation of mine communications equipment, using digital communications in the underground mine environment. It is a proven fact that an efficient underground mine communications system can help maximise production, by providing major gains in areas such as equipment and manpower utilisation, staff and vehicle tracking, reaction times to break downs and emergencies. In this paper we will describe some of the facilities that are currently available, as well as what will soon be available to mining and tunnelling companies around the world.

Jan 1, 1999

By D Ray, D Brett

A clay-capping trial was established in 1996 on Magazine Dump at the Mt Lyell Copper Mine. The trial was initially constructed under the Mount Lyell Remediation Research and Demonstration Program, a co-operative venture between the State and Federal governments. The detailed engineering design for the clay cover included the following features; reshaping and compaction of dump batters, 5 m vertical bench interval, overall side-slopes of 2.5:1, emplacement of clay in four 150 mm lifts, compaction by a 10 t vibrating roller or ætrack rollingÆ on batters with density testing for quality control. A small section at the base of the dump ( The trial also generated certain unexpected findings. Field permeability tests on the cover yielded uncertain results and oxygen remains available throughout the dump. The flow data indicate that, while total outflow has decreased as a result of storm shedding, inputs from groundwater and batter infiltration are still significant. Outflow during the driest weeks of the year may have risen following capping. Detailed assessment of the data is hampered by insufficient pre-capping information; however, there is a possibility that conductivity flux emitted when flows in the receiving environment are at their annual minimum is unchanged or worse post-capping.

Jan 1, 2003

By W Ward, J Clegg, R Barnes, T Zhong

This paper provides an overview of methods for measuring tunnel deflection and construction’s effects on the surrounding environment during and post construction. It will also review illustrative case studies from within Australia and overseas that are most relevant to local construction conditions. Systems illustrated include; vibrating wire and fibre optic strain gauges, extensometers, load cells and piezometers. A novel system using radar interferometry which requires no contact to the structure will also be investigated.In Australia, the majority of tunnelling activity occurs in urban areas (or in the case of mining in rural area) with limited seismic risk. However, the unexpected movement of tunnels is an important factor for structural engineers to monitor. During construction, monitoring is focused on the performance of the tunnelling lining, the supports under real conditions and the effects on surrounding infrastructure. After construction, monitoring will determine the effect of live traffic loads and can also evaluate the durability and any degradation of the tunnel. The aging of some tunnels or the forces subjected by nearby major construction can directly lead to a decrease in structural stability and deformation.The conventional way of inspecting and monitoring those tunnel movements is to have engineers physically enter the tunnel and carry out the measurement work. Manual techniques include tunnel wall convergence checks or total station measurement. However the associated costs are high and measurement process is difficult as some tunnel areas are inaccessible and the data collection interval is limited by the speed of the operator.Automated sensor networks utilising extensometers, fibre optics sensors or strain gauges can be used on tunnel segments or surrounding buildings. Ground settlement measurement via boreholes or hydraulic monitoring points and remote measurement of dynamic deflection can be taken using microwave interferometry.CITATION:Ward, W, Barnes, R, Zhong, T and Clegg, J, 2014. Sensors and systems for the measurement of tunnel movements during and after construction, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 209–218 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By G Pizarro, O Miranda, D Rosales

In panel/block caving mines, large amounts of information are collected at the operations. This information includes grades and extracted tonnage, fragmentation, lithology, design of stopes and main infrastructure, geotechnical information, overbreak progress, seismicity, numerical modelling and many other mine variables. To improve the reliability of the production plan it is required to integrate the mine data into one platform. In this paper, the logic of a new technological platform is presented for analysis, modelling and design in panel/block caving mines. The platform includes an acquisition system for mine data and geotechnical information, a back-analysis module for calibrating statistical models and a module of visualisation of the results. The application and benefits of the platform is illustrated for mining induced seismic risk for panel/block caving mining operation. The platform can be used in the mine design and planning processes and is useful for reducing uncertainty in the mining business of panel/block caving operations.CITATION:Miranda, O, Rosales, D, Pizarro, G and Vallejos, J, 2016. Development of an integrated platform for the analysis, modelling and design in panel caving mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 237–240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016