Search Documents

The paper focuses on how rock bolts are loaded in different rock masses, as well as in pullout tests. Three analytical models for rock bolts are presented in brief, one for bolts in continuously deformed rock masses, one for bolts in blocky rock masses, and one for bolts in pullout tests. The bolt models are used to interpret measurement data for rock bolts from three sources and to help specify the modes of axial load in the rock bolts. It is found that in continuously deformed rock formations fully coupled rock bolts have only one axial stress peak. The position of the axial stress peak moves towards the far end of the bolts with increasing rock deformation. In blocky rock masses several axial stress peaks may appear in the rock bolt. The position of this kind of axial stress peak does not change during the entire loading process. For rock bolts in pullout tests, decoupling of the interface always occurs first at the loading point. The decoupling front moves towards the far end of the bolt with an increase in the applied pull load.

Jan 1, 2000

By Yu A. B

An experimental study of the packing of a coal heap has been carried out. The bulk density of a coal heap is considered as a function of a number of variables, viz flow rate, conveyor belt speed, the height of the disengagement point of the conveyor belt, coal particle density, moisture content, the size of the heap and coal particle size distribution. The effects of the dimensionless numbers resulting from dimensional analysis on the packing density of a coal heap have been experimentally examined and analysed. Based on the experimental results, equations have been formulated for the estimation of the bulk density of a coal stockpile. The validity of these equations are checked by comparing the predictions with measurements of real industrial Stockpiles.

Jan 1, 1991

By Szwedzicki T, Jiang J

The acoustic emission (AE) technique has found wide application in rock engineering. Generally, acoustic emission, which is produced by a rapid microcrack growth, is an ubiquitous phenomenon associated with brittle fractures and can provide information on the failure process in rocks. The sudden release of stored energy in the form of an elastic stress wave that travels from the point of origin within the material to a boundary is called an AE signal or a discrete AE event. Based on a number of experiments and analysis, the correlations among the rock type, the complete stress-strain behaviour, mode of failure and AE properties are investigated and the AE pattern has been classified as four types: single-peak AE, double-peak AE, continuous AE and absent AE. Each type of AE pattern corresponds to a certain type of rock and is largely related to the internal structure and imperfection of a rock. Applications of the AE technique in stability monitoring, in situ stress assessment and seismic source location are also discussed.

Jan 1, 1995

This paper will review some of the work conducted in the past at the Dynamic Effects Laboratory to examine the use of stress waves and fracture mechanics in understanding dynamic fracture and fragmentation in blasting applications. Along the way, we will use photoelasticity and high-speed photography to better understand the mechanisms of fracture and fragmentation.CITATION:Fourney, W L, 2015. The role of stress waves and fracture mechanics in fragmentation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 27–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

A combination of the needs of business, employee desires and safety and health considerations is stimulating increasing attention to the time spent by people at work and the timing of that work. Particularly we are seeing: - innovative work schedules for 24-hour mining businesses; and - response from industry to accommodate the needs, even the desires, of employees in return for systems which are more productive and more capital efficient. There appears to be an evolutionary trend for business management to become more sophisticated and responsive to the need for achieving close to best cost work schedules to sustain continuous improvement. The underlying motivating forces driving this trend for improved techniques in organising attendance at, and time spent at work, is the seemingly inseparable combination of technological advance and ever-increasing accumulation of capital. The mining industry has not remained untouched by this thrust for ever-increasing need for best use of labour, to adopt advances in technology and to provide attractive opportunities for putting accumulated capital to work. An essential component of this on-going thrust is a substantial effort by the mining industry to improve the performance of labour by providing most-productive work schedules.

Jan 1, 1996

By W Liu, S Gao, D Wei, B Cui, Z Guan, Y Shen

Beneficiation of low-grade fine-grained hematite ores becomes increasingly important due to rapid depletion of high quality iron ore resources. However, fine particles, especially ultra-fine particles, make efficient beneficiation of these ores more difficult. Therefore, methods to reduce the influence of fine particles must be considered to achieve better beneficiation performance. Analysis and systematical beneficiation tests were carried out on an ultra-fine-grained hematite ore slime from washing a fine grained hematite ore. Ore particles were found to be presented in loose soil. While some of the ore particles were agglomerated, they were very fine and contained up to 76.5 per cent -0.023 mm material. In this paper, using a single magnetic separation flow sheet with sodium silicate (SS) as a dispersing agent, a concentrate containing 65.05 per cent Fe was obtained at an iron recovery of 68.58 per cent from the hematite ore slime of 56.65 per cent Fe. The single magnetic separation flow sheet was simple and reliable, the agent SS was effective in dispersing ultra-fine particles. The results are believed to be applicable to similar hematite ores.CITATION:Wei, D, Guan, Z, Gao, S, Liu, W, Shen, Y and Cui, B, 2013. Beneficiation study of an ultra-fine-grained hematite ore slime, in Proceedings Iron Ore 2013 , pp 495-500 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By A Harburg, A Dendys, G Green

Dugald River Mine (DRM) is located approximately 85 km north-east of Mount Isa, and 65 km northwest of Cloncurry, in the north-west Queensland Minerals Province of Australia. DRM is an underground operation and includes an above ground processing area, a 200 ha tailings facility, two waste rock dumps and associated infrastructure. The mining method is conventional underground longhole open stoping and downhole benching of a lead/zinc deposit within a black slate environment. The deposit is estimated to contain ~53 Mt of zinc and lead, which will be mined over a 30-year period. During operations, waste rock is segregated into either Potentially Acid Forming (PAF) or Non-Acid Forming (NAF) based primarily on the sulfide concentration of the rock. In particular, the NAF waste rock is an asset and is used for various small construction projects during operation; however, its primary use is for rehabilitation work at closure. Since beginning operations in 2017, DRM has generated more NAF than was originally anticipated. Whilst this is an excellent asset to DRM, it did pose a logistical problem of where to store the additional NAF for the life-of-mine and how to manage the run-off. DRM experiences distinct wet and dry seasons with hot conditions and periods of rainfall between November to April, and relatively dry and mild conditions between May to October. Majority of rainfall is received between January and February with an annual average rainfall of 501.1 mm. Short and intense rainfall events are common. DRM’s above ground infrastructure is land-locked between two large ephemeral watercourses, making the significant expansion of any assets challenging from a permitting/regulation and cost perspective. MMG is also a member of the International Council on Mining and Metals (ICMM) and is committed to adapting to a changing climate through operations and closure. Following extensive studies DRM opted to store the additional NAF material into the adjoining NAF Dam and concurrently upgrade a previously minor sediment basin into a highly engineered sediment basin which relies on automatic flocculant dosing to meet the required discharge quality limits. This basin is climate-resilient in that the dosing system can be adjusted to counter high intensity extended rainfall events which produce highly variable inflow water quality. This abstract broadly describes how DRM designed and implemented an engineering innovation to enable the site to meet the changing climatic challenges. The abstract then describes the process to design the sediment basin and how the dosing rate was established and validated. Finally, the abstract comments on the effectiveness of the sediment basin and how it has revolutionised DRM’s approach to water treatment and management; all whilst minimising the disturbance footprint of the operation

Aug 2, 2023

By M Slight, H Lacy

In recent times, with the global mining industry’s focus on sustainable development there has been a significant focus on mine closure and rehabilitation performance and reporting through the development of the International Council on Mining Metals (ICMM), the Global Reporting Initiative and the Equator Principles. In addition, financial reporting obligations under International Financial Reporting Standards and the Sarbanes Oxley Act (2002) have also led to better understanding and improvements with industry closure performance, liability management and reporting.Under these sustainable development principles and financial reporting obligations, mining companies are required to consider mine closure planning and associated cost estimates across all life cycle phases of the mine. Internal processes have been developed within mining companies to better understand their closure liabilities and obligations and likely costs and cost estimating processes are generally developed for long-term life-of-mine (asset) planning and budgeting, financial reporting for corporate balance sheet provisioning purposes, and regulator reporting for environmental bonding and financial assurances.These days mining companies need to plan for, prepare and actually mine for closure right from the start of a project. This means that their closure and rehabilitation liabilities throughout each stage of the mine life cycle phases must be understood, planned for, managed and controlled.So how is the industry performing? Understanding of closure liabilities is improving and reflected in liability cost estimations that are recognising the likely issues to be faced at closure, but there is a way to go to ensure that the industry doesn’t add to the increasing legacy liabilities being passed onto the wider community.CITATION:Slight, M and Lacy, H, 2016. Closure liabilities – where are we at?, in Proceedings Life-of-Mine 2016 Conference , pp 28–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By S Matos Camacho, K G. van den Boogaart, R Tolosana Delgado, U Mueller

"The precise formulation of a geometallurgical optimisation problem is by necessity a simplification of reality. It includes implicit choices such as data availability or mining block geometry. Additional data can be orebody data, production data or market data. Often these choices are predetermined by the software, the workflow or the corporate culture, and as such are not even queried. There are several aspects that might play a role in the optimisation. They include not only the spatial model on which the selection of mining blocks and the potential mining sequence are based, but also the complexity of the processing model, the way in which uncertainty is treated, the scope of responsibility and the complexity of the model. In addition the timing of the optimisation and the availability (or lack thereof) of information will influence the outcome of any optimisation.We show that different modelling choices and different model formulations for the same mine can lead to very different processing choices, substantially different net present values (NPV), opposite investment decisions and so to overall different values for the entire operation. The selection of adequate simplifications and corresponding formulations for the optimisation problem is thus an important task in itself.For this purpose we introduce a method for quantifying the impact of certain simplifications prior to the optimisation. For example, the effect of mining block choices depends mainly on the spatial structure and the structure of the processing gain function. Both can be quantified beforehand. Based on the outcome, appropriate simplifications can be selected for the geometallurgical optimisation.CITATION:van den Boogaart, K G, Tolosana Delgado, R, Mueller, U and Matos Camacho, S, 2016. How Details of the Geometallurgical Optimisation Influence Overall Value, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 303–312 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By M Oyarzún

Direct relationships between rock texture and BWi (grindability index) have been established based on geological and metallurgical information supported by optical microscopy observations, gathered from 731 samples.Each recognised rock texture is observed to be related to a certain BWi range and, this texture is also characteristic of distinct lithological subunits (recognisable at mapping scale). Therefore, this relationship may provide an important tool for early milling in situ estimation.Since each textural type is a response to rock formation conditions, the causality of the relationship between BWi and texture is based on such conditions and, particularly, on the interfacial free energy among its components.According to the abovementioned textural features, the greater the free interfacial energy between mineral components, the greater the necessary energy required to break its grain boundaries and, consequently, the greater the necessary energy required for milling.If the textural evidence indicates that the rock was able to adjust the shape and/or size of its components – in a natural tendency of all systems to minimise energy– then the necessary energy required to break its grain boundaries will be lower.

Sep 5, 2011

By G D. Matthews, M E. Haylett, S Khosrowshahi, A Weeks

Effective domaining is fundamental to geostatistical modelling for grade control. Through analysis of lithological, structural and alteration logging data, effective groupings (domains) can be identified and employed for estimation or simulation purposes.The poor definition of domains can adversely affect the grade control model resulting in a misinterpretation of the optimal ore-waste boundary and ultimately reduces the quality of recovered ore. The implementation of an appropriate domaining strategy is therefore expected to improve recovery and reconciliation.A thorough understanding of the geology of the deposit and adequate sample data is required for selecting domains. For new deposits, a resource drill database and resource model may be the only information available. Where extension to a previous operation is taking place, historic grade control, mapping and exposed geology may be used to improve domain selection. Preconceptions about domains, should they exist, need to be re-evaluated and tested to ensure they are fit for the purposes of grade control.While mining progresses, the domain model is re-evaluated to ensure that the previous interpretation is still suitable for the present configuration and geology. The grade control process, being iterative, lends itself to regular review and continuous improvement as further data is collected during the grade control cycle. Regular updates to the geology model, mapping, geostatistical data analysis and review of variography will provide indications of a changing domaining environment.Narrow vein gold deposits, which may have several factors influencing mineralisation, present considerable domaining challenges. By scrutinising the data, sample populations can be grouped into domains, which not only improve ore recovery, but help assist in the development of a mine geology model.CITATION:Matthews, G D, Haylett, M E, Weeks, A and Khosrowshahi, S, 2014. Effective domain selection for grade control in narrow vein gold deposits, in Proceedings Ninth International Mining Geology Conference 2014 , pp 191–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By C Vejrazka, A Wyllie

A common problem faced by underground mining operations around the world is airborne dust sourced from production and auxiliary processes. In most underground mining methods, air is generally directed through a limited number of drives and is thus more effective at carrying dust away from operational areas quickly. In a block caving operation, there are a number of ways to set up ventilation systems. In its simplest form the air is entering the extraction level through access drives and then split over the number of extraction drives—based on the pressure differences—without being regulated. This is the case at Northparkes Mines. Larger operations and panel caves most often utilise designated ventilation levels and ventilation raises with some form of regulation to ensure adequate airflow to all work areas.Northparkes Mines utilise electric loaders as a productive means to transport ore to the run-of-mine (ROM) bin, which have the added advantage of allowing the mine to require less airflow through the extraction drives as dilution of exhaust gases is no longer required. Dust was controlled during the operational period of the previous two block caves by using water spray bars in each of the drawpoints, which were seen as the main source of dust. These drawpoint spray bars only wet the surface of muck piles and require a lot of water to achieve an effect on the overall air quality. The drawpoint sprays can be remotely operated from mine control, whenever a loader is sent to bog a particular drawpoint. A significant amount of airborne dust is also generated during loading as rilling of material occurs, with further dust being generated during tramming and dumping activities as only limited mixing of the water and ore occurs. The water sprays are ineffective at precipitating dust that has already become airborne.When built, the currently operational E48 cave was fitted with drawpoint water sprays. As the cave is in a different orebody with higher silica content, the water sprays were not able to keep airborne dust and thus silica quantities under control efficiently. It was therefore necessary to find more sustainable solutions. The problem was further intensified by the concurrent load-haul-dump (LHD) processes across multiple extraction drives and tipping points, as well as secondary breaking, using non-explosive blasting and development activities occurring nearby.This paper describes the practical approach taken at Northparkes Mines to reduce personal dust exposure on the E48 extraction level. As the extraction level is one of the main contributors to airborne dust at the mine, it is believed that much can be learnt by focusing improvement efforts initially on this part of the mining process and later applying the effective solutions in other parts of the mine.CITATION:Vejrazka, C and Wyllie, A, 2014. Reduction of airborne dust on the E48 extraction level at Northparkes mines, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 227–232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By C E. Loo

The cohesive zone has a significant influence on blast furnace operation and performance. The high-temperature behaviour of the reducing ferrous burden determines the properties of the cohesive zone and is studied in a laboratory using a softening and melting test. This paper summarises recent work aimed at better understanding the physico-chemical changes in a ferrous bed during softening and melting. Using a combination of standard, non-standard and quenched tests supported by optical image analysis, this work has highlighted some important differences in behaviour between lump, pellets and sinter as well as between the two lump ores and two acid pellets. As with the two lump ores, one pellet is denser than the other and the denser ore/pellet is also higher in silica.Within the cohesive zone, densification of the ferrous layer leads to reduced permeability and greater pressure drop. From the work presented in this paper, two key mechanisms of ferrous layer densification were identified. Firstly, the formation of fayalite, which melts at low temperatures, can act as a lubricant between particles and lead to densification of the ferrous layer under load. Secondly, reduction to metallic iron is topochemical and fayalite in the outer shell of the particle restricts gas flow to the centre and results in the formation of a wustite core. As temperatures rise, the wustite melts and eventually exudes out of the shell, occupying void spaces between particles and further reducing layer voidage and permeability.This work has shown that density and silica content are two key factors that result in increased densification of the ferrous layer. For porous Australian lump ore, the higher porosity and lower silica reduces the formation of fayalite and limits the formation of the wustite core, ultimately leading to a more permeable bed. The difference between the porous and dense ores was more pronounced with the introduction of prereduction to better simulate blast furnace conditions. This suggests that a porous ore gives significantly better cohesive zone permeability and blast furnace operations than a dense ore.The behaviour of fluxed sinter particles is different in that the silica reacts with lime to form dicalcium silicate. Minimal wustite core forms because relict hematite particles in sinter are only small and reduction occurs uniformly throughout the particle. Even with significant loss of material through prereduction, beds formed from sinter remained comparatively rigid. Studies using a typical blast furnace burden mix of 80 per cent fluxed sinter and 20 per cent porous ore showed that the structures of these beds at softening and melting temperatures are very similar to the sinter-only test. Measurements of bed contraction and pressure drop also confirmed that the introduction of 20 per cent porous ore into a sinter bed did not alter its properties. This is an indication that 20 per cent ore can be easily accommodated by blast furnace burdens.CITATION:Loo, C E, 2015. Important acid ferrous burden properties in the cohesive zone of a blast furnace, in Proceedings Iron Ore 2015, pp 367–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By D A. Deglon

Solids suspension is important in the design and operation of mechanical flotation cells, and is a necessary precondition to particle collection. Most of the fundamental hydrodynamic research that incorporates some aspect of solids suspension was done by Arbiter, Harris, and co-workers, or Schubert and co-workers. However, a need for research into solids suspension in mechanical flotation cells exists, since very little has been done since the late 1980s; a time that also coincides with the advent of round mechanical flotation cells and the subsequent dramatic increases in maximum flotation cell sizes. In this work, concentration profiles and critical impeller speeds, Njs, were measured in a 0.124 m3, round cell fitted with a 0.150 m, Bateman impeller mechanism. Two solids size fractions (75 - 106 and 150 - 250 ¦m) were tested, in ungassed and gassed conditions (JG = 0, 1 cm/s) and at various impeller speeds (300 - 900 rpm). The effectiveness of solids suspension was quantified in three ways in terms of extent of off-bottom solids suspension, suspension height (extent of solids distribution), and variation within the solids distribution, which together present a complete quantitative picture of solids suspension and distribution within the cell. Consistent trends were found when these effectiveness criteria were considered against relative impeller speed, in terms of percentage of critical impeller speed, N/Njs. Off-bottom solids suspension is complete at or above 100 per cent of Njs, with significant sedimentation occurring as the impeller speed drops below 60 per cent of Njs. Suspension heights consistently reached a level equivalent to 90 per cent of the tank diameter at the critical impeller speed, and dropped off significantly as N/Njs dropped below 60 per cent. The variation in the solids concentrations within the sampled profiles showed consistent trends in two-phase but not under three-phase conditions. The paper concludes that the critical impeller speed, Njs, commonly used in the design and operation of standard stirred tanks, is a very useful solids suspension benchmark for describing all aspects of solids suspension in mechanical flotation cells and should be correlated to system conditions.

Jan 1, 2005

Australia is presently the world's principal producer of rutile and zircon, and also provides a major share of the world's ilmenite. Since 1980, Australia's share of the world's output of these minerals has fallen. Exhaustion of known resources, together with the changing composition of new deposits, is expected to result in Australia's share of the rutile and zircon output continuing to decline. Its role as a major supplier of upgraded ilmenite, that is synthetic rutile, is expected to increase. In 1994, the Bureau of Resource Sciences assessed Australia's demonstrated resources of mineral sands as follows: rutile 14.4 Mt, ilmenite 132.5 Mt, and zircon 21.0 Mt. These resources are located along the coast of Queensland and New South Wales, in the Murray Basin of New South Wales and Victoria, in the southwest corner of Western Australia, and in the Eneabba region, north of Perth. However, some 45 per cent of rutile and zircon resources along the coast of Queensland and New South Wales are not available for mining because of environmental concerns. World demonstrated resources are estimated at 40 Mt (contained TiO2) for rutile, 50 Mt for zircon and approximately 312 Mt (contained T1O2) for ilmenite. Outside of Australia, the most important resources of rutile, ilmenite and zircon are in South Africa (rutile, zircon , and ilmenite in the form of titania slag), Sierra Leone (rutile), India (ilmenite, zircon and rutile), and Canada (hard rock ilmenite). Significant resources of ilmenite occur in Madagascar and Mozambique.

Jan 1, 1996

By J Jeffery, P G. Knott, F Velge, C Evans

A trigger action response plan (TARP) provides a structured response to escalating levels of risk. In mining, TARPs are typically applied to primary hazards such as inrush, strata failure or heating. Necessary for the creation and deployment of a TARP is a monitoring system capable of detecting deviations from normal conditions. The advent of real-time instruments capable of measuring diesel particulate matter now permit decision-making within shifts to address possible overexposure. Deploying a TARP for diesel exhaust emissions can lower the probability of a person’s average exposure (over a full shift) exceeding the exposure standard by detecting deviations of diesel particulate concentrations from normal conditions. This enables pre-emptive action to mitigate or protect. Another goal is to drive ambient air concentrations lower through the application of corrective actions as a result of instances where concentrations exceed ‘normal’.CITATION:Knott, P G, Evans, C, Velge, F and Jeffery, J, 2015. Trigger action response plans for diesel exhaust exposures, in Proceedings The Australian Mine Ventilation Conference, pp 129–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By D J. Williams, A Shokouhi, A Naderian

Extracting alumina from bauxite involves the production of fine-grained waste known as red mud. The highly alkaline red mud is usually neutralised by applying sea water, thickened to between 25% and 30% solids by mass, before disposal to a Tailing Storage Facility (TSF). Hydraulic sorting, settling, self-weight consolidation, and desiccation are the processes contributing to the overall volume change of the red mud after deposition. Investigating the effect of these processes on the volume change behaviour of the fine-grained red mud is an important step in the estimation of the required storage volume of the storage facilities. This paper presents the results of a series of laboratory consolidation tests in a slurry consolidometer, and comparisons are made with field testing and observations.CITATION:Shokouhi, A, Naderian, A and Williams, D J, 2018. Assessing the volume change behaviour of red mud through laboratory and field testing, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 309–316 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

Coal losses and dilution are among a coal mine operators everyday problems. These losses and unwelcome additions are generated primar- ily by the stripping operation and secondly by the coal mining opera- tion. Losses in yield due to preparation plant efficiency are a separate issue although they may be related to the coal mining operation. The losses and dilution can be traced to the following operations: (A) Overburden or Interburden Removal (1) Removal of coal edge by blasting operations. (2) Removal of top of seam by drilling/blasting. (3) Removal of top of seam by stripping equipment. (4) Removal of coal edges by stripping equipment. (5) Dilution due to stripping equipment. (B) Coal Mining (for the case where seams are ripped rather than shot) (1) Coal rib losses. (2) Coal rib dilution. (3) Coal left in floor. (4) Coal left in fault areas. (5) Floor material picked up whilst loading. (6) Spoil material picked up. (7) Spoil material from poor surface clean up. (8) Top of coal losses from final clean up. (9) Dilution from ripping too deep, i.e. into floor below seam. (10) Dilution from interseam parting. The losses apply to both the single seam and multi seam oper- ations although they are more pronounced in the multi seam mines than in a single seam mine due to the position of the coal which is lost. For example in the multi seam case the top seam coal edge loss is final. There is little chance of recovery with the subsequent pass even if the extra rehandle is done. However conversely the lower seam is relatively easy to locate as it has nowhere to go being contained by the lowwall bench.

Jan 1, 1988

A description of:1. Air-lock at No. 14 Upcast shaft.2. Pit-top gates at Dudley winding shaft.3. Safety rider employed in sinking No. 18 shaft.1. AIR-LOCK AT No. 14 SHAFT.Some time ago it became desirable to raise and lower the McBride tunnel men to save them walking the inclined tunnel, about a mile in length, with a dip of nearly 600 ft., and a maximum gradient of 1 in 4. The main Upcast shaft, No. 14, was, therefore, equipped for winding the men. As this shaft was the main ventilating shaft for the McBride tunnel mine, it was necessary to take the greatest precautions against leakage of air. The writer therefore devised the concrete structure shown in Plate 1.The structure, as shown, surrounds the shaft inside the poppet legs. As the men are wound on double-decked cages (twelve men to each deck) provision is made at both top and bottom for the two decks to be loaded and emptied simultaneously. The doorsover the sky shaft, shown in the drawing, have been cut out and the sky shaft has been close-timbered with a double layer of T. and G. flooring boards, with building paper between, nearly up to the thimble frame, a small hole only being left for the winding rope topass through. The space between the ramps is glazed with plate glass to allow the winding-engine driver a good view of the pit top.The men are wound from two levels, 302 ft. and 611 ft.2. PIT-TOP GATES AT DUDLEY WINDING SHAFTTo minimise the shock to cage, couplings and rope when winding quickly, the writer devised the apparatus and arrangement shown in Plate n.

Jan 1, 1928

By Barber C, Buselli G

Detailed monitoring of point sources of groundwater pollution is expensive due to the high cost of drilling monitoring boreholes. Whether groundwater pollution is due to mining, industrial or domestic waste disposal, a universal difficulty when monitoring groundwater contamination is the placement of boreholes to adequately define the extent of the pollution plume. This paper reports groundwater 'resistivity variations determined from transient electromagnetic soundings at a domestic waste disposal site north of Perth in Western Australia. Together with available hydrogeological and water quality data, the geophysics provides a broad "plume scale" picture of groundwater contamination. A simple three dimensional model of plume development, which takes account of the dimensions of the wastes, has also been developed and shows good agreement with the spread of contamination indicated by the geophysics for relatively small values of the dispersivities. Better estimates of these parameters are still required. The work indicates that a combination of geophysics and modelling with ground-truth data from groundwater quality monitoring of boreholes is required to avoid difficulties in interpretation of data and to better define the extent and migration of pollution in Groundwater.

Jan 1, 1988