Search Documents

By WM. HUFF WAGNER

Computations and allowances for mine depletion for Federal income tax purposes depend upon the meaning of certain terms in the pertinent provisions of section 114(b) 4 of the Internal Revenue Code. Unfortunately, but one of these terms is defined in the Code. Congress left it to the Commissioner to define the other terms in the Regulations. Even though the Commissioner, through his staff, labored long and earnestly to draft these definitions they have not been satisfactory to the mining industry, because the definitions in the Regulations and the interpretation placed thereon by the Commissioner do not state what the industry believes to be the clear and obvious intent of Congress. Consequently serious and prolonged disputes, unduly delaying the settlement of Federal tax returns involving percentage depletion deductions are continually arising between taxpayers and the Commissioner.

Jan 1, 1949

By R. V. Norris

In a former paper on this subject,' I summarized Murgue's theory and experiments, and presented a large number of tests of mine-fans, stating some conclusions, " more or less warranted by the evidence," as to design, capacity and efficiency. Since that time the very valuable report of Mr. M. Walton Brown: Committee on Mechanical Ventikators, Institution of Mining Engineers, has appeared, and I have made additional experiments which tend to clear up some points in connection with this subject. Design and Tests of the Luke-Fidlbr Colliery Fan. The Luke-Fidler fan (see Figs. 1, 2 and 3), built to replace an old wooden fan at a very fiery colliery, presents some pecu-

Jan 1, 1905

By Nicholas J. Grant, William H. Ferguson, Bill C. Giessen

Ta-lr alloys have been examined over the complete range of compositions using metallographic and X-ray techniques. The terminal solid-solubility limits, solidus temperatures, and intermediate phases were determined. There are four inter-mediate phases: o, tetragonal, analogous to a (Fe-Cr); 0,. orthorhombic; az, tetragonal; and a TaZr,, cubic, AuCu, structure. Of these, o and a, melt peritecticaLly, a, decomposes peritectoidally, and a TaIrs has a congruent melting point. Three peri-tectic and one eutectic reactions occur. 1 HE Ta-Ir phase diagram has not been treated in the literature. Intermetallic phases and terminal solid solubilities have been described and estimated.'-4 The previous findings have been confirmed in this work. A complete diagram with additional phases and solidus curves is presented. EXPERIMENTAL METHODS Starting materials were tantalum powder of 99.8 pct purity, supplied by the National Research Corp., Cambridge, Mass., and iridium powder of 99.9 pct purity, supplied by the Bishop Co., Malvern, Pa. Both powders were -200 mesh. Table I lists the analyses as given by the suppliers. A standard procedure was employed in making the alloy buttons, which was described in detail in Refs. 5 and 6, and which included repeated arc-melting of powder compacts and determination of the composition by the weight-balance method. This is especially justifiable due to the similar vapor pressures of tantalum and iridium. In the critical parts of the diagram, a spacing of 1/2 at. pct was used, based on premelted master alloy material. The observed structures and X-ray spectra were consistent with the composition sequence of the alloys. Table II lists the final alloy atomic percentages with the calculated percent error of composition. Cross sections representative in grain size and composition were selected for the study, as described in Ref. 5. Based on prior experience, no contamination from the tungsten electrode was considered. Temperature measurements were obtained using a Leeds and Northrup optical pyrometer and have been described extensively in Refs. 5 and 6. All heat treatments were made in the high-vacuum tantalum tube furnace mentioned in Ref. 5. Samples annealed in tantalum containers cooled from 1800" to 1000"~ in 5 sec; those annealed in ceramic crucibles cooled over the same range in 15 to 30 sec. The thermal treatments are listed in Table 111. All specimens were homogenized at 1735°C for 24 hr. Tantalum-rich compositions were treated in tantalum buckets. Iridium-rich compositions were annealed in tantalum buckets below the eutectic temperature of 1950°C; up to 2200°C, tungsten-lined tantalum baskets were used; and above 2200°C thoria crucibles were used. It was found that refractory oxides (in early stages of the investigation alumina crucibles were used up to 1800°C and thoria crucibles were used to 2400"~) give off minute amounts of oxygen and thereby influence the microstructure considerably, or react directly with the alloys.

Jan 1, 1963

By Wm. A. Haven

As soon as the likelihood of American participation in the war was established, and in spite of the fact that we can produce almost as much as all other countries combined, the demand for prompt deliveries of iron and steel products from American factories began to exceed their utmost capacity, and, after fifteen months of practically full operation, has continued to do so. Therefore, it would seem worth while to review some of the aspects of the supply and demand for steel as well as the efforts that are being made to bring them into balance. It is still being debated as to whether the situation should be defined as a real shortage that will persist through the emergency period or as a temporary one than can be relieved by less drastic measures than a Government-sponsored program of expanding existing plants and building new ones.

Jan 1, 1942

By Carle R. Hayward

LEAD ore smelting plants have been operating in general at reduced capacities and secondary lead has assumed relatively more importance during the last year. Present smelting practice results in a large amount of dross, often over 25 per -cent, from blast-furnace lead. This is usually treated at a fairly high temperature in a reverberatory furnace to remove part of the lead and produce a matte-speiss product which is shipped to a copper plant. Few smelters are satisfied with this 'treatment. The fume losses are high and the matte-speiss contains considerable lead. It would seem that a fruitful field for research was open here.

Jan 1, 1934

By W. H. Class

The embrittling effects of oxygen, ozone, nitrogen, air, and surface residues, on NaCl has been investigated. The embrittlement by ozone and oxygen was found to be associated with the formation of a NaClO3 surface compound. In these cases the initial crack that was responsible for fracture (in a bend test) always nucleated at the corners between the tension and side faces. The behavior of air was very erratic and on certain days did not produce enzbrittlement. During these periods, crystals that had become embrittled by the ozone treatment completely recovered their ductility after a short exposure to the ambient atmosphere, It was established many years ago1 that considerable ductility could be obtained in NaCl single-crystal specimens if the crystal surfaces were dissolved in water either during or immediately prior to the test. The original interpretation of this effect by Joffe attributed the enhanced ductility to the removal of surface microcracks by dissolution. Later investigations2'3 have suggested that the exclusion of air from the specimen surface is the criterion for extensive plastic flow prior to fracture. The air em-brittlement in this later work was attributed to the diffusion of gaseous atoms into the surface layers of the crystal, thereby impeding the movement of dislocations. This model satisfactorily accounts for the reembrittlement observed after further air exposure subsequent to the water dissolution treatment. However, the situation has recently become more complex by the observations in several laboratories4-t that under certain conditions air exposure does not impair the ductility of NaC1. It has also been recognized5 that improper drying operations after water dissolution can leave surface precipitates that lead to embrittlement. Cleavage defects on as-cleaved crystals can often be another source of embrittlement. In the present work the effect of the gaseous atmospheres nitrogen, argon, air, oxygen, and ozone, on the ductility of rock salt was studied extensively. The embrittlement resulting from oxygen and ozone exposures was found to be associated with the formation of a NaC1O3 surface film. It is suggested that certain atmospheres, one of which often can be ambient air, which inhibit the formation or favor the decomposition of this compound, can promote ductility. Thus one aspect of the Joffe effect is certainly related to the removal of surface compounds or complexes by water dissolution. The effect of surface precipitates that remain after drying operations and of cleavage defects were also studied. In neither of the latter cases was the embrittlement as severe as that found with a NaClO3 surface layer. PROCEDURE AND SPECIMEN PREPARATION The nature of the embrittlement produced by the agents mentioned above was studied by means of microscopy, mechanical testing, and X-ray diffraction. Specimens were cleaved from large crystals of optical quality sodium chloride obtained from the Harshaw Chemical Co., and, except for those tested in the as-cleaved condition, were given a 15- to 20-sec immersion in distilled water followed by a rinse in absolute methyl alcohol. The specimens were then blotted on a soft, absorbent paper, and dried by a few seconds exposure to a stream of warm, dry air. Such a procedure was found to give a control surface which was microscopically free of residues. (A few crystals were intentionally painted with a concentrated NaCl solution in order to investigate the effect of surface residues). All specimens were of 0.140 sq in. cross-section. Crystals prepared in the above manner were immediately placed in a gas train where they could be exposed to the desired gases for preselected periods of time. For the oxygen and nitrogen exposures, pure reagent-grade gases were employed. The ozone was provided in the form of an ozone-oxygen mixture (approximately 10 pct ozone) prepared by passing commercial grade oxygen over a strong ultraviolet light source. All gases were dried prior to their introduction into the train. Since argon was found to be completely inert in its behavior (i.e., residue-free specimens that were exposed to argon were not embrittled), it was periodically utilized to check the control specimen surfaces as well as the condition of the gas train used for aging the specimens. After exposure to the gaseous media in question, the crystals to be used for the measurement of the strain to fracture were transferred from the gas train to a protective oil bath (without further exposure to the atmosphere) where the tests were conducted in three-point bending. The apparatus was so adjusted that the load could be applied at a constant, continuous rate. Other Snecimens from the gas train were deformed

Jan 1, 1962

By E. H. Rose

IN these days of the spectacular in research and technological accomplishment, it is easy and natural to overlook some of the applications to everyday life of recent developments of a more pedestrian kind, or to fail to realize that sometimes two or three of the latter may be combined to serve a novel purpose in fields other than those in which they grew. The present remarks are to point out three such developments which might be combined to apply to an everyday function of the A.I.M.E. as an organization. By its Constitution, the A.I.M.E. is organized "to promote the arts and sciences connected with . . . minerals and metals, and the welfare of those employed in these industries . . .; to hold meetings for social intercourse and the reading and discussion of professional papers, and to circulate . . . among its members the information thus obtained . . .; and to . . . maintain . . . a library." By these words of Article I the profession of mining and metallurgy is recognized to involve many arts and sciences, of which the art and science of exchanging information is a leading one. As to methods of preparing or securing papers, the Constitution is silent.

Jan 1, 1944

By E. G. Schempp, W. A. Morgan

The influence of modifications in the molybdenum, vanadium and, to a limited degree, carbon and boron content to a basic composition of 5 pct Cr, 0.75 pct Mo, 1 pct V hot-work tool steel composition, was studied in respect to hardenability, grpain- coarsening temperature, and tempering charactevistics. Tensile, impact, and fatigue pvoperties were studied for the most promising compositions. An alloy with a typical composition of 0.43 pct C, 4.97 pct CI-, 0.33 pct Si, 2.25 pct Mo, and 1.00 pct V uas found to offer the most favorable combination of properties in respect to high-strength applicntions when tempered at 1100°F. MANY 5 pct Cr high-strength steels are at present being manufactured in North America which fit well into the classification of the AISI-SAE system. Much interest has been shown in these materials as ultra-high-strength steels for use at elevated temperatures. The limiting temperature of use lies at the point where the steels begin to soften rapidly. Although a great deal of information has been made available in the past two years on the properties of selected alloys in this series, little information exists on the effect of systematically varying the ccntent of one or more elements in the 5 pct Cr-base alloy. This paper presents the results of an investigation of the effect of variations of the carbon, molybdenum, vanadium, and, to a limited extent, the silicon, manganese, boron, and niobium content of a 5 pct Cr steel to the AISI H-13 base analysis. EXPERIMENTAL PROCEDURE All experimental heats were melted in a 50-lb. induction furnace. The melting stock consisted of

Jan 1, 1962

By M. R. Geer

THE increase in the number of coal-cleaning plants employing dense-medium processes occurring since 1946 is especially interesting when viewed historically. Both sand and magnetite were introduced as material for heavy mediums at about the same time, sand in the Chance process in 1921 and magnetite in the Conklin process in 1922, but from that point on their records diverge. The Chance process enjoyed a steady growth from its inception, whereas no additional magnetite plants were built in the United States for over 20 years. Then, following the close of the World War 11, magnetite was again introduced, this time with marked success. During the following years some 47 plants employing magnetite medium were built.

Jan 7, 1953

By R. L. Fullman

IN the investigation of metallurgical transformations and the relationships between microstructure and properties of metals, it frequently is desirable to obtain a measurement of the relative amounts of the various phases present and of the mean size of particles into which each phase is dispersed. The relative amounts of the phases can be measured by the classical methods of area, lineal, and point analysis,1-5 in accordance with the principle that the volume fraction of a phase, the fraction of a polished cross section occupied by the phase, the fraction of a random line occupied by the phase, and the fraction of randomly arrayed points occupied by the phase are all equal. The validity of this relationship depends only on the attainment of a truly random sample of area, length, or points, and not on the size, shape, or distribution of the particles constituting the phase. Smith and Guttman8 have derived a relationship between the interface area per unit volume S, and the measurable quantities L., the interface length per unit area on a cross section, and NL, the number of interfaces per unit length intersected by a random line. Their equation, Sv = — L8 = 2NL is also valid regardless of the distribution of particle sizes and shapes. In contrast to the situation concerning measurement of relative fractions of phases and of interface area, the measurement of particle sizes in opaque samples has not been subjected to a complete analysis. It has been common to measure some lineal or area dimension of particles on a polished cross section and to use the mean value as a qualitative measure of particle size. In the present paper, quantitative relationships are established among the various mean dimensions on a polished cross section and the actual dimensions of the particles present. Particles of Uniform Size Spheres: If a metal sample contains particles of a phase a dispersed in the form of spheres of uniform size, a polished cross section through the sample will reveal circular areas of phase a with radii from 0 to ?, the radius of the spheres. Consider a cube of unit dimensions to be cut from the sample. If a cross section parallel to one of the cube faces is examined, the average number of particles per unit area (N,) equals the number of particles per unit volume (Nv) times the probability p1 that the plane would intersect a single sphere positioned at random within the unit cube. Since, of the various possible positions for the cross-sectional plane over the unit length from top to bottom of the cube, only those positions existing over the length 2r would lead to the plane intersecting the sphere, the probability of intersecting a single sphere is just 2r. N8= Nvp1 = Nd-2r [1] Applying the equality of area and volume fractions, the relationship is found between sphere size and average area s of uniform spheres intersected by a random cross section, 4 - f = NV V = Nr . — pra = N s = Nd . 2rs S = —pr2 [2] A similar analysis reveals the average traverse length across spheres of uniform size when random lines are passed through the sample. If a randomly oriented unit cube is cut from the sample and a randomly positioned line is passed through the cube parallel to a cube edge, the number of spheres intersected by the line (Nl) equals the number of spheres per unit volume times the probability p1 of the line hitting a single randomly placed sphere in the cube. Since possible positions of the line occupy unit area, and possible positions for which it will pass through the sphere occupy an area of pr2, the probability of the line hitting a randomly placed single sphere is pr2. NL = Nv p1 = Nvpr2 [3] Combining this relationship with the equality of volume and lineal fraction, the desired relationship is obtained between radius and mean lineal traverse length -i, for spheres of uniform size. 4 - - 3 l=4/3r [4] Circular Plates: Consider a sample containing particles of a phase a in the form of circular plates of uniform radius r and thickness t, where r >> t. If the plates are randomly oriented, as in a sufficiently large sample of a fine grained polycrystalline material, area and lineal analysis may be carried out with parallel cross-sectional planes and lineal traverses. If the plates are not randomly oriented, it is necessary to randomize the orientation of the cross-sectional planes and traverse directions. Let a unit cube be cut from the sample, and a cross-section plane be passed through the cube parallel to one of the cube faces. The number of plates cut by the cross-sectional plane per unit area is equal to the number of plates per unit volume times the probability of a plate intersecting a single randomly positioned and randomly oriented plate in the cube. If J is the component of the plate diameter in the direction normal to the cross-sectional planes, the probability of a plane cutting a single randomly oriented plate is equal to J, the mean value of J for all possible orientations of the plate. Let 4 be the dihedral angle between a plate and the cross-sectional plane, and let p?, d? be the probability that a plate makes an angle between 4 and ? + d? with the cross-sectional plane. Then for ran-

Jan 1, 1954

By R. M. Hudson

The removal of nitrogen from a nitrogenized low-carbon sheet steel that contained 0.011 wt pct N was determined during heat treatment in Hz-N, mixtures. TIze process followed a first-order rate law; that is, plots of the logarithm of nitrogen content in steel were linear with the time of treatment at a given temperature. The rate of removal increased with an increase in temperature from 900" to 1300°F. By 1400°F the rate in dry hydrogen had decreased to a value intermediate between the rates at 1200" and at 1300°F; in wet (2.47 vol pct water vapor) hydrogen the rate at 1400°F was less than the rate at 1300°F and nearly the same as the rate at 1200OF. The rate at a given temperature increased as the 3/2 power of hydrogen concentration in the atmosphere. While wet atmosplzeres were generally more effective than the corresponding dry atmosplzeres, the effect of water vapor was much less pronounced than the influence of hydrogen content. NITROGEN is the principal agent in the strain aging of ferrite, the effect of carbon being secondary.' To eliminate the return of the yield point after straining and aging, it is claimed2 that the amount of nitrogen in solution in steel must be reduced to 0.0002 wt pct. Strong nitride-forming elements (titanium, vanadium, zirconium, and aluminum) can act to eliminate strain aging by combining with nitrogen. It is extremely difficult to decrease the nitrogen content in commercial steels to the low level required by conventional coil annealing because of the poor contact between the strip surface and the reactive atmosphere. However, a variety of gas-metal reactions can be effected by use of the open-coil annealing method,3 in which the metal surface is fully exposed to the atmosphere. With this possibility in mind, the Applied Research Laboratory has studied the influence of time, temperature, and atmosphere composition on the removal of nitrogen from low-carbon sheet steel. MATERIALS AND EXPERIMENTAL WORK Samples from a commercial nitrogenized low-carbon steel (0.010 in. thick) in the cold-reduced condition were used. The chemical composition of this steel is given in Table I. The gas mixtures used are listed in Table 11. The moisture content in the "wet" annealing atmospheres was controlled at a +70°F dew point (2.47 vol pct water vapor) by passing the gas mixture through a glass tube packed with a solid mixture of 10 pct anhydrous oxalic acid and 90 pct oxalic acid dihydrate held at 127°F; this technique has been described previously.4 For "dry" atmospheres, the gas mixtures were passed through a cold trap immersed in liquid nitrogen. A hinged-top Hevi-Duty electric furnace was used with a Vycor-glass furnace tube. When the furnace was at the desired temperature, the gas mixture was passed through the furnace at a flow rate between 1.1 and 1.2 cfh; coupons (size 3 by 3/4 in.) of the steel were pulled into the center of the Vycor-glass

Jan 1, 1964

By Sherwin F. Kelly, Bela Low

THE WORK OF THE DRILLER and of the oil geologist is seriously handicapped by the impossibility of actually seeing what is going on inside a borehole as it is being drilled. Visual information of the position and condition of the casing, and of the characters and attitudes of strata passed through would be of inestimable benefit. The best substitute for putting a periscope down a hole is the taking of photographs of its interior at points where information is desired. An apparatus for this purpose has been constructed by Dr. Thomas Reinhold, of Heemstede, Holland, and one instrument of his design has been put into practical use by the Geological Survey of The Netherlands in searching for water. To the best of our knowledge, this instrument has not been applied to oilfield problems, although the possibility has been mentioned in the one or two brief notices of the camera which have appeared in the literature.' The purpose of presenting this description of the instrument, with some examples of its work, is to suggest that it might be adapted to serve a variety of useful purposes in American oilfields, and with the hope that discussion will bring out any modifications necessary to make the apparatus more valuable to drillers and geologists.

Jan 1, 1932

By AIME AIME

THE STANDARD herewith submitted is the result of several years of research and consideration by the A.I.M.E. Technical Committee on Milling Methods. In the early work of this committee it was found necessary to undertake the development of a standard laboratory method for screen testing of ores. During the research stages the desirability of having this standard, when completed, approved as American Standard was brought out. In accordance with this idea, its initiation as a project of the American Standards Association (then the American Engineering Standards Committee) was approved by the latter body and the A.I.M.E. designated as sponsor. In 1929, the A.S.A., on recommendations of its advisory committee, the Mining Standardization Correlating Committee), authorized the A.I.M.E. to be sole sponsor for this project. The personnel of the Institute's Committee on Milling Methods was then increased to make it thoroughly representative of all diversified interests in the mining field. Two years ago the standard was circulated and has been given wide distribution. Early in 1932 the committee voted unanimously, with 38 affirmative votes, that the standard be recommended to the Board of Directors of the Institute for submission to the American Standards Association for approval as American Recommended Practice. This was accordingly done, at the Feb. 1.6, 1932, meeting of the directors, and the American Standards Association approved the standard on July 6; 1.932, designating it as ASA M5-1932.

Jan 1, 1932

By G. W. Brock

Experiments in the form of aging of overstrained tension specimens and elevated temperature tension testing, have been carried out on recrystallized arc-cast molybdenum. The aging behavior of molybdenum was found to be strongly dependent on the degree of plastic strain present in the lattice: the reason for this being the low solid solubility for the common interstitial elements in molybdenum. GEORGE W. BROCK, formerly Research Associate, Department of Theoretical and Applied Mechanics, University of Illinois, Urbana, III., is Research Associate, Department of Engineering Sciences, IBM Research Center, Yorktown Heights, N. Y. Manuscript submitted January 19, 1961. IMD THE term strain aging is familiar in connection with the recovery of the yield point in mild steel after tensile overstraining, and there are other instances where it is known to exert an appreciable effect on mechanical properties. For example, steel exhibits a greater tensile strength at mildly elevated temperatures than at room temperature and serrated stress-strain flow curves occur under certain conditions. It has been known for a number of years that the phenomenon of strain aging is directly connected with the presence of carbon and nitrogen in the lattice; and extremely small amounts of either element are sufficient to produce the effect. In this study, the aging behavior of overstrained tensile specimens of recrystallized molybdenum has

Jan 1, 1962

By C. Schlumberger, M. Schlumberger

In order to explore electrically a terrain composed of a succession of horizontal beds, a current of known intensity i is caused to flow between two grounds A and B, and the resultant drop of potential , caused by the resistance of the earth, is measured between two given points in the soil, M and N. In practice it is convenient to choose the two points M and N so that they lie on the line AB and their midpoint coincides with the middle 0, of that line, although this is not imperative. When the lengths L and I of the two lines AB and MN are varied, equations are obtained which may be solved for the resistivity p of the subsoil at various depths. Recall briefly that the formula 4 x l gives the average resistivity, in the horizontal direction, of a layer of earth which extends to a depth1 about equal to L/4. This elementary concept is adequate for numerous practical applications. Nevertheless, it must be said that, in many cases, a rigorous mathematical analysis may be made, provided it is always a question of homogeneous, superposed horizontal beds. The authors expect to publish, later on, appropriate methods of calculation for some specific cases.

Jan 1, 1932

By J. Spotts McDowell

INTRODUCTION The magnitude of the thermal expansion of silica brick, and its inability to withstand rapid temperature changes, present problems of considerable importance in the manufacture of siliceous refractories. In the study represented by the experimental data herein described, these problems are considered from the point of view afforded by the results of recent investigators: Fenner and his associates of the "Geophysical Laboratory, Washington, D. C., who have established the stability relations of the silica minerals, and Endell and co-workers in Berlin, who have studied the changes brought about in the constitution of siliceous refractory materials upon the application of heat. In the process of manufacture, the quartzite from which the brick is made changes in part into cristobalite and tridymite. The attempt is herein made to determine by microscopic methods the degree of transformation in various specimens of test bricks manufactured at slightly varying temperatures of burning, with varying coarseness of grain, and to determine the effect of repeated burning. The effect of variations

Jan 10, 1916

By A. L. Galpin

INTRODUCTION For many tailings ponds, particularly those having substantial watershed areas, the control of pond water levels will be a major factor influencing the operation of the pond and the design and construction of the dam retaining the pond. This paper summarizes the basic factors affecting the control of water in tailings ponds, methods of water control, and methods of estimating the variables involved. The influences that pond water levels can have on the design, construction, and stability of tailings dams are explained in order to emphasize the importance of water control in the overall planning of mine tailings disposal systems. Two examples of pond water control planning conclude the paper. BASIC FACTORS The principal factors influencing the control of water in tailings ponds are illustrated on Fig. 1. Fig. 1 (a) shows the general disposition of the tailings solids and water in the pond; the solids settle from the slurry to form "slimes", deposits sloping down into the pond from the points of discharge; these slimes hold volumes of water in the voids between solid particles; water in excess of this "retained" water forms a pool of "free" water laying over the slimes deposits. In some cases, tailings solids (and water) go to the tailings dam for its construction. Fig. 1 (b) indicates those ways additional to tailings disposal in which the pond gains or loses water. These include surface and sub-surface runoff from the pond watershed, water reclaimed from the pond for ore processing, evaporation, and seepage. Seepage losses sometimes include water draining from tailings sand placed in the dam, but a portion of the total seepage flow is often collected and returned to the pond in order to avoid downstream pollution and to recover water for re-use. PRINCIPAL REQUIREMENTS In relation to the control of water in a tailings pond, the first requirement is usually to maintain a pool sufficiently large to ensure adequate clarification of the free water prior to its reclaim for use in the mill, or its discharge from the pond.

Jan 1, 1972

By A. Kounosu, T. Fujita, J. Shimoiizaka, K. Nakatsuka

Stable aqueous dispersion of magnetite colloid of about 10 nm in diameter was obtained by allowing an anionic or nonionic surfactant to adsorb on the hydrophobic surface of magnetite particles prepared by monomolecular adsorption of oleate. Sodium dodecylbenzene sulfonate, sodium oleate and poly (oxyethylene) nonyl phenyl ethers whose hydrophilic-lipophilic balance (HLB) are higher than 12 were suitable for giving a second adsorption layer to obtain a stable dispersion. Stability of the colloidal suspensions depends upon pH of the solution and is controlled by the dissociation of the adsorbed surfactant in the second layer. The addition of ethyleneglycol, which was used for lowering the freezing point of the dispersion, did not affect the stability when used in amounts smaller than 60% of water. Preparation of diester-based ferrofluids was also attempted by the same procedure using a nonionic surfactant as second layer molecule. Hydrophobic magnetite colloid, which had been preliminarily coated with mono-molecular oleate, was suspended in di(2-ethylhexyl) agipate, azerate, and sebacate respectively, and dispersion stability was investigated by adding various poly (oxyethylene) nonyl phenyl ethers of different HLB values. It was found that those with HLB values between 10.9 and 13.3 were suitable for this purpose. Stabilities of the dispersions in a magnetic field were investigated up to 1 T by applying an electromagnetic field. No separation of dispersant was observed and each magnetite dispersion displayed the characteristics of a magnetic fluid.

Jan 1, 1980

By J. Ruben Velasco, Roland B. Mulchay

CANANEA has long been recognized as a remarkable field for geologic study. The copper deposits and rocks of the district have been described by many geologists and engineers, but only the most general correlations have been made between Can-anea sedimentary rocks and other known sedimentary sections in the southwestern United States and northern Mexico. The present paper describes the Cananea sediments in greater detail than has been done before and attempts to fit the Cananea sedimentary section more closely into the geologic time table. The lack of well-preserved fossils has made it difficult to date the sediments accurately in geologic time, but it is possible to make tentative correlations between the Cananea sediments and the southeastern Arizona sections, based largely upon lithology and general position in the geologic column. It appears that sedimentation at Cananea and Bisbee may have been closely similar during Paleozoic time. Even such generalized correlations, however, may be subject to considerable modification in the future. The present study has led to the recognition of other problems of age and mineralization relationships in the Cananea district. Cananea is located in the north-central part of the state of Sonora, Mexico, at an elevation of 5270 ft. It is about 135 miles northeast of Hermosillo, the state capital, and 25 miles south of the international boundary. By road Cananea is 40 miles from the twin towns of Naco, Ariz., and Naco, Sonora, and about 50 miles from Bisbee, Ariz. It is served by the Nogales-Naco branch of the railroad, F.C. Pacifico, and is connected with Chihuahua and Mexico City by the Aeronaves airline. The headwaters of three rivers flowing to the Gulf of California are located in the Cananea Mountains: the San Pedro River, flowing to the north; the Sonora River, flowing south and west; and the Mag-dalena River, flowing west. Elenita Mountain, the highest point in the district, has an elevation of 8140 ft. The Cananea Mountains extend in a series of north-south to northwest-southeast spurs and ridges and are surrounded by gently sloping gravel plains. The mineralized area, lying across the southern and central parts of the range, is about 6 miles long and at most 2 miles wide. Elevations at the mines vary from 5300 ft at Cananea-Duluth mine at the southeast end of the district to between 6000 and 7000 ft at the west end of the mineralized area at Puertecitos-Elenita mines. Principal production has been from the intensely mineralized and altered area of Capote Basin in the central part of the district and the immediately surrounding area to the southeast. The district has produced over 2 billion lb of copper, substantial molybdenum, and minor amounts of lead, zinc, silver, and gold. Total production through 1949 is estimated at more than $300 million. In 1900 large-scale development was started at Cananea by W. C. Greene. Until World War II only high-grade ores were exploited; low-grade ores were extracted after the installation of a large concentrator in the early 1940's, and subsequent operations have been based upon mining and processing ores containing less than 1.0 pct copper from open-pit and underground workings. Mining and concentration of such low-grade ores, however, are made possible only by continued high copper prices, and active exploration for high-grade orebodies has been continued throughout the important mineralized areas. General Geology Study of the involved rock pattern at Cananea has indicated a complex geologic history for the district. Widespread alteration and mineralization have masked many of the salient features and have led to widely varying geologic interpretations over the years. Further work will probably disclose new information which will modify current beliefs. At Cananea a conformable series of sediments of probable Paleozoic age was deposited on an unknown basement. Following Paleozoic time there was an extended period of erosion common to many districts in the southwestern U. S., and there is no present evidence of marine sedimentation at Cananea after the Paleozoic. The eroded surface was eventually covered with a great thickness of extrusive volcanic rocks. The entire series of sediments and volcanic rocks was later intruded by a variety of deep-seated igneous rocks. These included the Cananea granite, the Cuitaca granodiorite, the El Torre syenite, the Tinaja diorite, the Campana diabase and gabbro and the Colorada rhyolite quartz porphyry. Faulting of early age, probably prior to the deposition of the volcanic rocks, may have been responsible for the present position of some of the intrusive rock masses. In the Capote mine on the third and fourth levels the northwest-striking Rick-etts fault zone, with apparent offset of about 800 ft, has been sealed by a dike-like mass of Cananea granite which gradually increases in size with depth. In lower levels of the mine the granite forms a large southeast-plunging mass generally following the course of the Ricketts zone. The granite is not known southeast of the Capote-Oversight mine areas and the Ricketts fault does not appear in the vol-canic~ southeast of Capote Basin, but several plugs of Colorada quartz porphyry cut the volcanics along the assumed general southeast trend of the Ricketts zone. These porphyritic intrusives may be the up-

Jan 1, 1955

By W. W. Anderson

A formula for quantitative efficiency is proposed, in which the efficiency value is a function of the improperly distributed material at the, gravity of separation effected by the cleaning equipment. The misplaced material is expressed as a percentage of the total material discharged from the equipment. Numerous examples are given, demonstrating application of the formula to various types of separation, including multiple-product separations.

Jan 1, 1950