Search Documents

By Paul Soros

The cost of shipping British coal by water to domestic and ex- port users has been expensive. The traditional transportation system functioned as follows: coal in up to 50 different grades was accumulated in railway cars at several loading ports; on the arrival of a vessel, cars were dumped in the desired order to produce the required blend. It was a direct rail- road-to-water interface. Railroad freight was high because of the poor utilization of the large number of small (14, 18 or maximum 28-ton capacity) hopper cars required. Ocean freight was high because the ships were small, mostly on the order of 1500-3000 dwt and even these took a long time to load. Assembling and loading larger cargo presented a challenge in logistics to the ports, the railways and the coal washeries. The accommodation of larger bulk carriers was hampered by a tidal range of up to 24 ft which led to the development of impounded harbors, with locks that limit the size of vessels.

Jan 12, 1973

By Raymond E. Zimmerman

Abstract-The Swirl Cyclone developed in Japan, although based upon the same principles as the standard cyclones for heavy-media or water-only cyclones for cleaning coal, is novel in that it is invested with the apex on top, discharging rejects at the top, and clean coal at the bottom. It also uses a variable air vent tube for controlling the vortex. Tests conducted indicate that its efficiency is not only as sharp as standard cyclones but it also performs using a much coarser grain magnetite, promising higher magnetite recovery. The author describes the results of tests conducted in Japan on a very difficult coal.

Jan 2, 1978

By Raymond E. Zimmerman

The Swirl Cyclone developed in Japan, although based upon the same principles as the standard cyclones for heavy-media or water-only cyclones for cleaning coal, is novel in that it is invested with the apex on top, discharging rejects at the top, and clean coal at the bottom. It also uses a variable air vent tube for controlling the vortex. Tests conducted indicate that its efficiency is not only as sharp as standard cyclones but it also performs using a much coarser grain magnetite, promising higher magnetite recovery. The author describes the results of tests conducted in Japan on a very difficult coal.

Jan 1, 1979

By W. G. Oldham

By monitoring the capacitance of abrupt p-n junctions it is possible to follow the motion of substitu-tional impurities. A p-n junction is formed by growth of silicon from an Al-Si alloy on an n-type silicon sutstrate at a temperature in the range 650" to 750°C. The diodes are etched and sorted for consistent V-I and capacitance behavior and separated into groups. After irradiation, each set with an unirradiated control set is annealed to various temperatltres for 10 mm and the capacitance remeasnred. For very heavily doped diodes (-1019 per cm3) observable capacitance changes occur at neutron fluences of >1015 per cm 3. The results may be interpreted in seceral ways, the simplest of which is to assume simple vacancy diffiision with small impurity -racancy interaction (at the diffiision, i.e. annealing temperature of 700°C). In this interpretation it is found that a typical vacancy makes about 1024 jumps and travels about 10-5 cm before disappearing. The required effective annihilation center density is about 1016per cm3 . Estimates of the vacancy-impurity interaction can be made and the above numbers correctecl, but for arty reasonable assumptions the number of vacancy sinks connot be much reduced. ThE complete annealing of radiation induced defects requires that the vacancies and interstitials either recombine, travel to the surface of the crystal, or travel to an annihilation center, e.g., a dislocation or a precipitate. If the interstitial is ignored except as a possible vacancy annihilation center at low temperatures,* the motion of vacancies may be followed by monitoring the corresponding motion of substitutional impurities. pfister2 has measured the enhanced diffusion of impurities in an asymmetric shallow diffused silicon structure by optically monitoring the junction movement. In these experiments we monitor instead the capacitance of a heavily-doped deep symmetric p-n junction. The sensitivity for this method is several orders of magnitude higher than in Pfister's technique, mainly for two reasons: 1) the junction capacitance of a heavily-doped junction is sensitive to impurity movements in the Angstrom range* com- and 2) the junction may be far from the surface which is a major annihilation center for vacancies. THE EXPERIMENT A p-n junction is formed by the epitaxial growth of silicon from an A1-Si alloy on a silicon substrate at a temperature in the range 650° to 750°C. The technique used is the transport of an aluminum melt through a temperature gradient.4 A 10-mil thick aluminum disc is sandwiched between two silicon wafers and the assembly raised to about 650° C with a temperature gradient normal to the sandwich. After about 8 hr the upper (hotter) wafer has been entirely transported and deposited epitaxially on the substrate wafer. The substrate and overgrowth resistivity are measured with a 4-point probe. The as-grown structure is lapped until the wafer is about 1/2 mm thick with the junction in the center. Contacts consisting of electroless nickel covered by electroplated rhodium are applied to both the p and n sides. The wafer is diced into square dice 1/2 to 1 mm on a side and the dice are etched sufficiently to remove approximately 1 mil of silicon. The following results are all for aluminum (p-side) and antimony (n-side) doped specimens with NA =3x 1018 per cm3, ND = 2-8 x 101A per cm3. The diodes are sorted for consistent V-I and capacitance behavior and separated into groups. After irradiation, each set with an unirradiated control set is annealed and the capacitance remeasured. A special capacitance measurement method is used to insure a low sensitivity to shunt resistance. The diode is voltage driven and the current monitored by a phase lock amplifier. It is possible to adjust the detector phase to a point where shunt resistances as low as 100 O have no effect on the reading. The diodes in this study have a capacitance in the range 1000 to 5000 picofarads and a shunt resistance in the range 100 to l06 O depending on the stage of the anneal. THEORY The theoretical problem is twofold: 1) The computation of the amount of impurity diffusion and hence the impurity profile resulting from a given amount of vacancy motion, and 2) the computation of the capacitance from the impurity profile. A comparison of the theoretical and experimental capacitance (in particular the changes) yields the amount of vacancy motion. Vacancy Motion. A convenient parameter to measure the total amount of vacancy motion is Jv the total number of vacancy jumps per unit volume. Although this parameter varies with position in the crystal, owing to vacancy annihilation at the surfaces, it is approximately independent of position far from the surfaces, i.e. in the junction region. In terms of the number of vacancies per unit volume Nv and the vacancy diffusivity given by

Jan 1, 1970

By G. Wakefield, A. H. Daane, D. H. Dennison, F. H. Spedding

Preparation of pure scandium metal was accomplished by calcium reduction of the fluoride by two methods; a low-temperatzdre alloy process and direct reduction with subsequent distillation of the product. The following properties were determined: melting point: 1181OK; boiling point (calculated): 3000°K; lattice constants at 298°K (hexagonal lattice): a = 3.308 * 0.001 A, c = 5.267 * 0.003A; calculated density at 298°K, g per cm3: 2,990 + 0.007; electrical resistivity, ohm-cm: 299°K, 66.6 ± 0.2 x 10 -6; 373oK, 77.4 * 0.2 x 10 -6; thermal coefficient at 299°K, ohm-cm per deg: 5.4 X x; heat of sublimation at 298°K, kcal pel- mole: 80.79. The vapor pressure was determined as a function of temperature between 1505o and 1748°K, with the data fitted to a straight line shielding the equation: Log Pmm = -1.718 X 104/ToK + 8.298. SCANDIUM, element number 21, was first discovered by Nilson in 1879 and was recognized as the Ekaboron as predicted by Mendeleff. As it is in group III of the periodic table, the general properties are a little like aluminum and also resemble quite closely the properties of yttrium and the rare-earth metals, in both the metallic and ionic form. Although the earth's crust contains approximately 5 ppm of scandium (the element is as abundant as arsenic and twice as abundant as boron) it generally occurs so widely distributed that it has earned the reputation of being very rare. The one exception to this is the mineral thortveitite, which has been found in Madagascar (20 pct Sc2O3) and in Norway (35 pct Sc2O3). Scandium also occurs in small but distinct amounts in uranium and rare-earth ores; the recent larger scale processing of these materials has made some scandium available from these sources. As with other naturally-occurring monoisotopic elements (except Be), scandium contains an odd number of protons and an even number of neutrons. Scandium metal was first prepared by Fischer and coworkers1 in 1937 by electrolysis of scandium chloride in a molten eutectic mixture of lithium and potassium chlorides, using molten zinc as a cathode and collector of the scandium metal produced. The zinc was removed from the Zn-2 pct Sc alloy by vacuum distillation, leaving a product reported to be 94 to 98 pct Sc, with the main impurities being iron and silicon. They reported a melting point of 1400° C for this material. Scandium has also been prepared by the reduction of scandium chloride with potassium metal in a glass apparatus by Bommer and Hohmann in 1941,' resulting in a mixture of metal and potassium chloride; these workers did not isolate the metal proper, but the X-ray diffraction of the slag-metal mixture showed it to be hexagonal with a = 3.30A, c = 5.45A. petru3, 4 and coworkers have recently reported the preparation of the metal in a compact form by the reduction of either ScF3 or ScC13 with calcium metal and subsequent distillation of the product. This process probably yielded a metal of high purity, but they list no chemical analysis nor do they list any of the properties of their product. Previous related work in this Laboratory has been concerned with the production of yttrium and the rare-earth metals and the determination of their physical properties. Because of its similarity to these metals, scandium is being included in this study. PREPARATION OF SCANDIUM METAL The preparation of yttrium and the rare-earth metals may be accomplished by reduction of their fluorides with calcium metal in tantalum crucibles.5 This process leads to the introduction of tantalum (up to 0.5 pct) as an impurity in the higher melting rare earths, but since the tantalum occurs as dendrites, uncombined with the rare-earth metals, its presence is not objectionable in some cases. The preparation of scandium metal in this manner, however, was found to yield a product containing 2 to 5 pct Ta. To obtain a purer product, the following two methods were developed for the reduction of scandium fluoride with calcium metal: i) a low-temperature process utilizing zinc to form a low

Jan 1, 1961

By J. T. Norton, H. Blumenthal, S. J. Sindeband

The interstitial phases formed by the transition elements with carbon, nitrogen and boron constitute a unique class of substances which are of considerable technical interest because of their well developed metallic properties and their high hardness and melting points. They are also of interest from the point of view of structure. It was pointed out by Hagg1 some years ago that the principal factor determining these structures was the relative sizes of metal and metalloid atoms. He predicted that if the ratio of the radii of metalloid to metal atoms was less than 0.59, the metal atoms would be arranged in a close-packed fashion of relatively simple type. This prediction has been amply confirmed. It appears, however, that this specification applies most generally to those structures in which the metalloid atoms occupy isolated positions in the lattice and there is no tendency for strong binding between the metalloid atoms themselves. The series of borides of the type MeB2 formed from the transition elements of the fourth (Ti, Zr) and fifth (V, Cb, Ta) groups of the periodic table provide an opportunity to investigate this situation further. If one takes as a basis the radius of 0.87 A for the boron radius and the Goldschmidt values for the metal atoms in 12 coordination, then the radius ratio varies from 0.54 for zirconium to 0.64 for vanadium, which latter is considerably greater than Hagg's limit of 0.59. It was of interest, therefore, to see if these five elements would form borides of the MeB2 type and have simple isomorphous structures. When this investigation was initiated, relatively little information had been published on the structure of this group of borides. McKenna2 reported the preparation of ZrB2 by a carbon reduction process. Its structure was hexagonal and the approximate lattice constants were given as a = 3.15 A, c = 3.53 A. Ehrlich3 reported the structure of TiB2 as being of the C 32 type with a = 3.02, c = 3.21 and c/a = 1.06 A. Recently, Kiessling4 published the results on ZrB2, showing it to be one in which the metal atoms are arranged in a simple hexagonal lattice with the boron atoms in flat sheets, midway between the layers of metal atoms. The structure is C 32 type with a = 3.169, c = 3.530 and an axial ratio =1.11 A. He also states that CbB2 and TaB2 are isomorphous with ZrB2. Preparation of Borides The borides of titanium, zirconium, columbium and tantalum were made by the electrolysis of fused salt baths after the method described by Andrieux.5 The bath, totalling about 6500 g in each case had the following general composition: Metal Oxide + B2O3 + CaO + CaF2. The actual proportions of the ingredients were determined for each individual case. Although Andrieux reports the preparation of vanadium boride by the same electrolytic method, several attempts proved unsuccessful. However, it was possible to prepare VB2 by the carbon reduction method used by McKenna to produce ZrB2. The mixture consisted of V2O5 + 6B2O3 + 11C and the reduction was carried out in an induction heated graphite crucible. This method proved satisfactory for ZrB2 and TiB2 and undoubtedly the others could be made in the same way. The borides, which were all in the form of fine gray metallic crystals from the electrolytic bath or gray powders from the reduction process, were carefully separated from other constituents and analyzed chemically for metal and boron content. The densities of the boride powders were measured using a standard 10 cc pyenometer at 18°C and ethyl benzene proved to be the most satisfactory liquid for this purpose. X Ray Technique The boride crystals, as prepared, were too small for single crystal examination so that powder techniques were employed. Patterns of the finely ground borides were prepared, using the Norelco recording X ray spectrometer. The lines on these patterns were indexed with the aid of Hull-Davy charts and the approximate dimensions

Jan 1, 1950

By J. E. Hilliard, J. W. Cahn

calculation has been made of the standard deviations to be expected in the measurement of volume fractions by areal analysis, lineal analysis and four point-counting Procedures. The effect of experimetztal errors is not included. Our conclusion is that a point count using a two-dimensional grid will be the most efficient method of volume fraction analvsis providing the grid spacing IS coarse enough. The predicted standard deviation for such an analysis is shown to he in good agreement with that determined experimentally. A metallurgist wishing to estimate a structural property by means of quantitative metallography is often faced with a choice between several different procedures. In such a case, he will naturally wish to know: a) Which procedure is the most efficient in the sense of requiring the least effort for a given precision? b) For a given procedure, what are the conditions for maximum efficiency? c) Under these conditions, how many measurements are required to attain a given precision? It is our aim in this paper to provide at least partial answers to these queries as they relate to the estimation of volume fractions from measurements on a random two-dimensional section of an opaque specimen. The commonly used techniques1,2 for volume-fraction analyses are based on one or more of the following principles: i) For an areal or Delesse3 analysis: That the areal fraction of a three-dimensional feature intercepted by a random plane provides an unbiased estimate of the volume fraction of that feature. ii) For a lineal or Rosiwal4 analysis: That the fractional intercept on a line passing at random through a two-or three-dimensional feature provides an unbiased estimate of, respectively, the areal or volume fraction of that feature. iii) For a point-count analysis: That the fractional number of randomly or regularly dispersed points falling within the boundaries of a two-dimensional feature on a plane, or within the boundaries of a three-dimensional feature in a volume, provides an unbiased estimate of, respectively, the areal or volume fraction of that feature. The absence of bias referred to in these principles does not, of course, imply that the results of an analysis will be free of error, but only that the expected result is equal to the true one. Application of the foregoing principles provide the following six possible experimental procedures: a) An Areal Analysis—This involves the measurement with a planimeter (or other means) of the area of a constitutent intercepted by the plane of polish b) A Two-Dimensional Random Point Count—Apos-sible experimental procedure for this analysis is to superimpose a sheet of transparent graph paper on a micrograph, and then use a table of random numbers to select coordinates for the points. c) A Two-Dimensiotuzl Systematic Point Count-Similar to b) except that the points are distributed in a prescribed manner, usually at the corners of a lattice superimposed on a micrograph or the screen of a projection microscope. d)A Lineal Analysis—A measurement of the fractional line length intercepted. It is usually performed by traversing the specimen under the cross hairs of a microscope and recording the distance travelled in each constituent. e) 4 One-Dimensional Random-Point Count— This could be performed by traversing the specimen with stops at random intervals to identify the constituent then present under the cross hairs. f) A One-Dimensionul Systematic Point Count— Similar to e) except that the traverse is stopped at prescribed (usually equal) intervals. It will be noted that the point-counting procedures b) and c) can be regarded as methods of estimating the areal fraction. Similarly, e) and f) are indirect methods of making a lineal analysis. All of the six procedures described above involve at least one stage of sampling. Thus, quite apart from any experimental errors, there will always be a statistical uncertainty associated with the final results. It is with the calculation of this uncertainty that we will be concerned. To avoid unnecessary repetition, the statistical relationships that will be used in the calculations are collected together in the appendix. For a fuller discussion reference should be made to one of the many textbooks5,6 on statistics. For symbols relating to the specimen structure we will follow as far as possible the terminology used by Smith and Guttman.7

Jan 1, 1962

By C. D. Woodward

ThE subject of elcctric signals for the despatching of mining cagey through shafts has received cousiderable attention recently from various mining companies. The Anaconda Copper Mining Co. has found it necessary to develop a system that is rcliable, safe and simple in operation, and easy to repair. The movement of all mine cages or skips is under the direction of a station tender, who rides on the cages when men or supplies are being lowered or raised; when ore is hoisted, he is stationed at a skip pocket for loading and despatching the skips. For the station tender's use, two signal systems are installed in cach hoisting compartment, and he is the only employee authorized to use them. One system is known as the "AC " or station bells, as it is operated from the 110-volt, 60-cycle, power service; the other system, called the "DC" or shaft bells, takes its energy from closed-circuit primary batteries. As a supplemcnt to the two main signals, a buzzer system is installed The general arrangement is similar to the main signal, except that there is a mine buzzer at each station. When a signal switch connected into the buzzer system is pulled down, all buzzers arc operated, thus notifying the station tender that he is wanted at seine particular level. Placed on the station posts, and within easy reach of the men on the cages are the signal pull switches for the main signals. The station, or "AC," pull switches are furnished with a short rope as shown in Fig. I, while the shaft, or "DC," pull switches are equipped with ropes that extend down the shaft past the next station. To avoid all confusion in the use of the three signal systems, a standard arrangement has been adopted in all mines for the location of the pull switches. Fig 2 illustrates the position of the pull switch at the various mine stations for the main signal systems, but it does not show the buzzer pull switch; this is fixed to the roof timbers about 25 ft. back from the shaft. If the skip pockets are a considerable distance below the station, a pull switch for each main shaft compartment is connected to the "AC" system and placed at this point. However, if the distance is short, a light cord is attached to the station pull switches and dropped down to the skip pocket.

Jan 1, 1923

By C. D. Woodward

ThE subject of elcctric signals for the despatching of mining cagey through shafts has received cousiderable attention recently from various mining companies. The Anaconda Copper Mining Co. has found it necessary to develop a system that is rcliable, safe and simple in operation, and easy to repair. The movement of all mine cages or skips is under the direction of a station tender, who rides on the cages when men or supplies are being lowered or raised; when ore is hoisted, he is stationed at a skip pocket for loading and despatching the skips. For the station tender's use, two signal systems are installed in cach hoisting compartment, and he is the only employee authorized to use them. One system is known as the "AC " or station bells, as it is operated from the 110-volt, 60-cycle, power service; the other system, called the "DC" or shaft bells, takes its energy from closed-circuit primary batteries. As a supplemcnt to the two main signals, a buzzer system is installed The general arrangement is similar to the main signal, except that there is a mine buzzer at each station. When a signal switch connected into the buzzer system is pulled down, all buzzers arc operated, thus notifying the station tender that he is wanted at seine particular level. Placed on the station posts, and within easy reach of the men on the cages are the signal pull switches for the main signals. The station, or "AC," pull switches are furnished with a short rope as shown in Fig. I, while the shaft, or "DC," pull switches are equipped with ropes that extend down the shaft past the next station. To avoid all confusion in the use of the three signal systems, a standard arrangement has been adopted in all mines for the location of the pull switches. Fig 2 illustrates the position of the pull switch at the various mine stations for the main signal systems, but it does not show the buzzer pull switch; this is fixed to the roof timbers about 25 ft. back from the shaft. If the skip pockets are a considerable distance below the station, a pull switch for each main shaft compartment is connected to the "AC" system and placed at this point. However, if the distance is short, a light cord is attached to the station pull switches and dropped down to the skip pocket.

Jan 1, 1923

By J. E. Ostberg, G. Phragmen, A. Hultgren, S. Wohlfahrt

Detailed study was made of a number of rimming ingots, both low and high carbon, and especially upon effects of superimposed air pressure. Requirement to suppress core bubbles is between 10 and 15 atm; at 6.5 atm freezing was in semikilled manner and at 3 atm, steel was of rising type. Probable mechanism of freezing under various conditions is discussed. AN earlier paper' reported an investigation made by a committee for studying rimming steel ingots appointed by Jernkontorets in Stockholm. The present paper is the outcome of some further work done by the same committee. Since the characteristics of ordinary rimming steel are connected closely .with the amount of gas liberated during freezing and since this amount of gas is governed by the pressure, it was considered of interest to ascertain in what manner and to what extent definite pressures applied to the top of the liquid steel in the mold would affect the solidification process and the consequent structure of a rimming steel of ordinary composition. The experiments were made at the Domnarfvets Steel Works. The steel was made according to normal practice in a 4-ton Rennerfelt electric furnace. Ferromanganese was added in the furnace; no aluminum was added, with one exception. Analyses of the four heats are given in Table I. The top-poured ingots measured about 12 in. sq x 48 in. and weighed about 1300 lb. One or two ingots of each heat were allowed to solidify under pressure, using a special device for admitting compressed air to the upper closed part of the mold, as shown in Fig. 1. A heavy plate sealed with asbestos was bolted to the top of the mold. The plate had a tapered aperture for pouring. Immediately after pouring the hole was closed by a wedged plug, and compressed air was admitted through a hole in the plug. Because of some delay in applying the plug, full pressure was not reached immediately. The pressure was adjusted to the desired value as indicated by a manometer. In order that the interior of the ingot might have the benefit of the pressure, the freezing of the top crust was delayed by a refractory lining applied to the top part of the mold, Fig. 1. Ingots were also cast from each heat without applied pressure, and with and without refractory lining at the top. Axial sections of ingots were cut either of the whole ingot or of some part of it of special interest; sections were polished and usually etched.' To facilitate description of structures the following terms may be used for different types of ingots solidified under gas evolution: 1. Box-hat or boot-leg ingot: Abundant gas evolution during casting and during rimming; no rim holes. 2. Normal rimming ingot: Lively gas evolution during rimming; usually rim holes in lowest part of

Jan 1, 1952

By M. H. Caron

D. C. Ralston—The fact that none of the organizations that have worked on these ammoniacal leaching processes have contributed discussion of Mr. Caron's papers today is a matter of some disappointment. Adaptations, modifications and improvements have been made by several organizations or individuals and to complete the record I want to document a number of them. The Nicaro Nickel Co. operated a Government owned plant at Nicaro, Oriente, Cuba, during the past war. A report on the project was written for Reconstruction Finance Corp. and is in the document file collected by the Office of Technical Services, Commerce Department and filed with the Library of Congress, where it can be consulted or bibliofilm or photostat copies obtained by asking for copies of PB 97271. Nicaro Nickel Co. has obtained a series of U.S. Patents, my list (probably incomplete) of which bears the following numbers: 2,400,098; 2,400,114; 2,400,115; 2,400,461; 2,400,612; 2,458,902 and 2,473,795. International Nickel Co. has also studied the problem and U.S. Patent 2,478,942 shows that some of the complications involving occasional low extractions have been unraveled. Forward, Samis, and Kudryk, of the University of British Columbia, have also published a study of copper-nickel sulphide concentrate.' Others are interested and it is evident that this type of hydrometallurgy is likely to find a happy application in the not-too-far distant future. Caron's two papers practically amount to a summation of his life's work on the important subject of nickeliferous iron ores and the American Institute of Mining and Metallurgical Engineers is fortunate to have been chosen the medium of publication. M. Rey—The ammonia leaching process has been the subject of certain studies in New Caledonia, but at the present time, the conditions are not very favorable to its adoption. The process is a combination of a thermal and a hydrometallurgical process. As a result, the first costs and the operative costs are rather high. To counteract this unfavorable situation, it would be necessary to make a very high extraction. But unfortunately, the process is delicate and in spite of all of Caron's valuable work, there are still many unknown factors. It is difficult to obtain regularly a high extraction, exceeding 75 to 80 pct. It would be interesting to have the opinion of Inter-national Nickel on the process and to know what the Dutch are doing in Celebes. M. H. Caron (author's reply)—I am quite familiar with the different types of nickel and cobalt ores as found on New Caledonia, and it may be pointed out that the Celebes ores are quite the same in their properties. Their behavior when treating the ores by the ammonia-leaching process is also alike and in my opinion, there is no reason why a high extraction of the New Caledonian ores could not be obtained if the process is properly applied. For the sake of completeness I may add that one of my patents has not been discussed in the papers. This patent deals particularly with the treatment of serpentine nickel ores. (Netherlands No. 62693 40a, French No. 965.786 April 21. 1948. and Cuban No. 13.625 Jan. 1950.)

Jan 1, 1951

By H. H. Kellogg

0. C. Ralston—The fact that none of the organizations that have worked on these ammoniacal leaching processes have contributed discussion of Mr. Caron's papers today is a matter of some disappointment. Adaptations, modifications and improvements have been made by several organizations or individuals and to complete the record I want to document a number of them. The Nicaro Nickel Co. operated a Government owned plant at Nicaro, Oriente, Cuba, during the past war. A report on the project was written for Reconstruction Finance Corp. and is in the document file collected by the Office of Technical Services, Commerce Department and filed with the Library of Congress, where it can be consulted or bibliofilm or photostat copies obtained by asking for copies of PB 97271. Nicaro Nickel Co. has obtained a series of U.S. Patents, my list (probably incomplete) of which bears the following numbers: 2,400,098; 2,400,114; 2,400,115; 2,400,461; 2,400,612; 2,458,902 and 2,473,795. International Nickel Co. has also studied the problem and U.S. Patent 2,478,942 shows that some of the complications involving occasional low extractions have been unraveled. Forward, Samis, and Kudryk, of the University of British Columbia, have also published a study of copper-nickel sulphide concentrate.' Others are interested and it is evident that this type of hydrometallurgy is likely to find a happy application in the not-too-far distant future. Caron's two papers practically amount to a summation of his life's work on the important subject of nickeliferous iron ores and the American Institute of Mining and Metallurgical Engineers is fortunate to have been chosen the medium of publication. M. Rey—The ammonia leaching process has been the subject of certain studies in New Caledonia, but at the present time, the conditions are not very favorable to its adoption. The process is a combination of a thermal and a hydrometallurgical process. As a result, the first costs and the operative costs are rather high. To counteract this unfavorable situation, it would be necessary to make a very high extraction. But unfortunately, the process is delicate and in spite of all of Caron's valuable work, there are still many unknown factors. It is difficult to obtain regularly a high extraction, exceeding 75 to 80 pct. It would be interesting to have the opinion of Inter-national Nickel on the process and to know what the Dutch are doing in Celebes. M. H. Caron (author's reply)—I am quite familiar with the different types of nickel and cobalt ores as found on New Caledonia, and it may be pointed out that the Celebes ores are quite the same in their properties. Their behavior when treating the ores by the ammonia-leaching process is also alike and in my opinion, there is no reason why a high extraction of the New Caledonian ores could not be obtained if the process is properly applied. For the sake of completeness I may add that one of my patents has not been discussed in the papers. This patent deals particularly with the treatment of serpentine nickel ores. (Netherlands No. 62693 40a, French No. 965.786 April 21. 1948. and Cuban No. 13.625 Jan. 1950.)

Jan 1, 1951

By J. M. Ohm, Carl M. Bunker

Two special tools for recovering gamma-ray probes and logging cable from drillholes have been designed by Ohm and Bunker and constructed by Ohm. Though intended specifically for U. S. Geological Survey equipment, they may be used with other equipment of the same general type. Fishing Tool for Probes: A fishing tool of the overshot type (Fig. 1) was designed to retrieve logging probes (sondes) that become disconnected from the logging cable and are trapped in the drillhole. When the tool slides over the top of the gamma-ray probe, studs on the bottom engage the shoulder near the top of the probe (Fig. 2), which is then pulled to surface.

Jan 10, 1959

W. H. SHOCKLEY, Chairman, FRANK H.-PROBERT, :Vice-Chairman, T. A. RICKARD, Sec.-Treas.; 420 Market St.,. San Francisco, Cal. C. C. BRAYTON, J. F. NEWSOM. A Meeting of the San Francisco Section was held on May 7, 1917. Chairman Shockley was in the Chair. The Section was honored by the presence of President Moore and Secretary Stoughton of the Institute. C. W. Merrill introduced President Moore, who then spoke to the Section on the Aims of the Institute. He discussed the possibility of improving the standards of membership by introducing a classification of membership. The present rigid investigation of applicants was pointed out by him. He spoke of the important influence that the local Sections can exert on the Institute and of the importance of sociability and informality at the meetings. Secretary Stoughton, who was introduced by the Chairman, emphasized somewhat the same points. He mentioned the need for making the Bulletin of the Institute more, interesting than it is at present, this to be accomplished by raising the necessary funds by increased advertising. He asked for an expression of opinion on this point. He. said that the employment department of the Institute is now used extensively. At the request of Mrs. Mark L. Requa, Mr. Stoughton. announced that a San Francisco branch of the Woman's Auxiliary of the, Institute was being formed and asked that the ladies of the members' families send in their names to Mrs. Requa or to the Secretary of the Institute.

Jan 10, 1917

By G. Nabi, W-K. Lu

Cylindrical specimens of natural dense hematite were reduced to magnetite at atmospheric pressure in H2-H2O mixtures of known composition over the temperature range 1084° to 1284°K. The rate of reduction was measured by the rate of movement of the interface between hematite and magnetite. The diffusion of gases through the gaseous boundary layer, the magnetite layer, and the interfacial chemical reaction were all considered in the interpretation of experimental data. The mass transfer coefficient through the boundary layer was calculated using accepted correlations. Values of the chemical reaction rate constant and the diffusivity of hydrogen in the magnetite phase were determined. THE present investigation is concerned with the reduction kinetics of natural hematite to magnetite by H2-H2O mixtures in the temperature range 1084" to 1284°K at atmospheric pressure. This reaction is the first step in the series of topochemical reactions in the process of reducing hematite to iron. Kinetic information of the simple steps such as hematite-magnetite transformation is necessary in order to have a better understanding of the complex processes of hematite reduction in iron-making. It also has direct industrial significance because magnetic roasting is one of the most important methods in benefication of lean ore.&apos; Although many technical papers have been published on the process of magnetic roasting and iron oxide reduction, very little information is available in the literature concerning the fundamental nature of hematite reduction to magnetite by reducing gases. Hansen et al.2 reduced the dense synthetic pellets of high-purity oxide in CO-CO2 mixtures and determined the reaction rate by weight-loss method. They were able to interpret most of their results by applying the interfacial area control theory developed by Mckewan.3 In contrast, Wilhelm and St. Pierre,4 who studied reduction of hematite to magnetite in H2-H2O mixtures by weight-loss method, stressed that the resistance of the porous magnetite layer to the diffusion of gases cannot be neglected in consideration of the overall reaction rate. In the present study the contributions of interfacial chemical reaction, diffusion of gases through the magnetite phase, and the gaseous boundary layer to the overall reaction rate will be considered. APPARATUS AND PROCEDURE Hematite Specimens Preparation. Natural hematite ore from Vermillon range of Northern Minnesota was selected for the present investigation because of its high purity and thermal stability. Chemical analysis of five samples gave the following average values: 67.52 pct total iron (96.62 pct Fe2O3, 0.28 pct FeO, 0.03 pct metallic iron), 2.53 pct SiO2, <0.07 pct MgO, 0.03 pct CaO, 0.05 pct combined mixture, 0.07 pct loss on ignition, and 0.34 pct other. Cylindrical specimens of 0.93 cm in diam and 2.7 cm in length were drilled from slabs of ore with a water-cooled diamond core drill. These specimens were heated to 1000°C and furnace-cooled. Specimens with silica pockets developed large cracks. The uncracked specimens were heated a second time, and their surfaces were carefully examined with a microscope. Those with hairline cracks or surface inhomoaenitv-- were rejected. Preparation of H2-H2O Mixtures. H2-H2O mixtures were prepared by the combustion of H2-O2, mixtures in a pyrex glass chamber in the presence of a catalyst. Alumina pellets coated with palladium, supplied by Englehard Industries, were used as the catalyst. Purified grades of hydrogen and oxygen were used which were repurified by usual techniques. Hydrogen before entering the combustion chamber was passed through an activated alumina H2O absorption bulb, with copper turning at the top. The cover of this bulb was not made pressure-tight so that any pressure development in the hydrogen line would cause the cover to blow off and also the copper turnings would act as a flame arrester in the case of a flashback from the combustion flame. Oxygen flow rates were measured with a bubble flow meter after purification with 1 pct accuracy. Hydrogen flow rates were measured by "precision wet test meter" and the amount of unburnt hydrogen was accurately measured by a bubble flow meter, after condensing water vapor in the gaseous stream. The Pyrex glass bulb contained concentric Vycor glass tubes as shown in Fig. 1. Oxygen was prevented from diffusing into the hydrogen line by threading platinum wire through pores at the combustion end of gas inlet tube. The glass bulb was heated with a Kanthal heating wire pasted in asbestos paper. The surface temperature of the bulb was measured with a thermocouple and adjusted to remain at approximately 350°C. The gaseous reaction chamber also served as a preheater for gases to avoid thermal segregation. The following sequence of operation was adopted. 1) Nitrogen was passed through the outer concentric tube to purge the catalyst bulb of oxygen. 2) Hydrogen was introduced through the inner tube until a steady flow was obtained. 3) Oxygen was then introduced into the nitrogen stream passing through the outer tube. 4) When combustion had commenced and a flame was visible over the platinum wire, the N2 was turned off.

Jan 1, 1969

By N. J. Grant, D. S. Bloom

THE development of high temperature, high stress alloys had proceeded with such rapidity during the war, and for a short time afterward, that our knowledge of the constitution of the alloys had become seriously inadequate. To interpret correctly alloy behavior it is not only necessary to recognize the phases present, but also to know the properties of the phases under all varieties of conditions and treatments. Chromium in these high temperature alloys holds the unique distinction of being the only one element which must be present when an oxidizing or generally corrosive atmosphere is present and when a long life is desired in service. Carbon and nitrogen must also be considered where chromium is present. Carbon is always present, either as an impurity in the raw alloying elements, or as a deliberate addition agent to increase the strength. Nitrogen is generally picked up from the atmosphere during melting or may be added as an alloying element. The effect of nitrogen additions is not too dissimilar to that of carbon additions. As such, chromium carbides and nitrides become of great interest since they are present in a very large number of alloys, including alloy steels, stainless steels, super alloys, and the like. In the chromium-carbon system there are three accepted, carbides: Cr,C, Cr7C8, and Cr3C2. The existence of one more carbide, a still higher carbon form CrC, has been advanced. The phase diagrams of chromium and carbon as published by Friemann and Sauerwald² and by Tofaute, Kuttner and But- tinghaus³ -do not extend beyond the carbide Cr3C2, which contains 13.3 pct carbon; but Hatsuta has extended the diagram up to 20 pct carbon, and in doing so hypothesized, with the use of some questionable experimental results, the compound CrC. This carbide would contain 18.75 pct carbon, 81.25 pct chromium, by weight. It is further known that as the chromium carbides increase in carbon the acid resistance increases but the oxidation resistance decreases4,5 This is of great importance in high temperature alloys where time-temperature stability, as well as oxidation resistance, is of prime importance. The possible existence of a carbide of the formula CrC thus becomes of prime importance and it was considered important to recheck the chromium-carbon binary constitutional diagram for such a compound. In view of the wide spread of values listed for the melting point of chromium (1500° to 1850°C) and 1930°C8, it was considered .that the liquidus temperatures might well be redetermined more ac-

Jan 1, 1951

By Arno C. Fieldner

METALLURGICAL coke and the by-products of the carbonization of coal continue in strong demand. Nearly 500 new by-product ovens were constructed in 1943. Output of by-product coke in the first ten months of the year was about 2 1/2 percent higher than in the corresponding period of 1942, but beehive production remained on approximately the same level as last year and constituted about 11 per cent of the total coke output.

Jan 1, 1944

By M. Bevis, A. F. Acton, P. C. Rowlands

Defor~nation twinning and transformation twinning modes most likely to be operative in Fe-Ni and Fe-Ni-C martensites have been determined using a new theory of the crystallography of deformation t~inning.~ This analysis shows that potentially important conventional and nonconventional twinning modes1 have been omitted in previous analyses. Discussion is given on the relevance of the predicted twinning modes to the lattice invariant shear associated with the martensite transformation in steels and to anomalous deformation twinning in Fe-Ni-C martensites. THE two most important criteria which appear to govern operative twinning modes in metallic structures1 are that the magnitude of the twinning shear should be small and that the twinning shear should restore the lattice or a multiple lattice in a twin orientation. The latter criterion ensures that the shuffle mechanism required to restore the structure in a twin orientation is simple. These criteria have been adhered to in the prediction of twinning modes2"6 in bcc and bct single-lattice structures with axial ratios in the range y = 1 to 1.09 as, for example, encountered in martensite occurring in steels. Refs. 2 and 3 in particular consider the martensite transformation in steels and the twinning modes in these cases relate to transformation twinning, and hence the lattice invariant shear associated with the martensite transformation. The list of twinning modes which can be compiled from these sources is incomplete and the ranges of magnitude of shear considered could be unrealistically small, particularly in the case of deformation twinning. The latter consideration is supported by the fact that twinning modes with magnitudes of shear large compared with the smallest shear consistent with a simple shuffle mechanism have been established in, for example, the single-lattice structure mercury7 and the multiple-lattice structure zirconium.&apos; In addition the anomalous deformation twins reported by Ftichrnan4 to occur in a range of Fe-Ni-C martensites still remain unexplained. It is clear that a comprehensive analysis of twinning modes likely to be operative in martensite In steels is required. The results of the application of a new theory of the crystallography of deformation twinningg to these structures are presented in this paper. The theory has been used to determine all shears which restore the lattice or a multiple lattice in a new orientation with magnitude of shear up to a required maximum. The orientation relationships between parent and twinned lattices are not restricted to the classical orientation relationships of reflection in the twin plane or a rotation of 180 deg about the shear direction. PREDICTED TWINNING MODES Twinning modes which restore all or one half of lattice points to their correct twin positions will be referred to as m = 1 and m = 2 modes, respectively. These modes are the most likely to describe operative modes in single lattice structures. The bcc m = 1 and m = 2 modes which have magnitudes of shear s in the range s < 2 and s < 1, respectively, have been given10 and are reproduced here in Tables I and 11. Detailed discussion of the crystallography of these modes and cubic modes in general will be discussed elsewhere (~evis and rocker, to be published). The four twinning elements Kl, &,ql,7)2 as well as the magnitude of shear s are given for each twinning mode, and the twinning modes are given in order of increasing shear. Two twinning modes are given in each row of the tables, the twinning mode Kl, Kz, ql, q2 and the reciprocal twinning mode with elements Kl = K,, Ki = Kl, q: = q2, and 17; = ql. The m = 1 and m = 2 twinning modes which describe twinning shears with small magnitudes of shear and simple shuffle mechanisms in bct crystals with -y = 1 to 1.09 are given in Tables I11 and IV, respectively. On increasing the symmetry of the tetragonal lattice to cubic, that is making y = 1, all modes listed in Tables 111 and IV must reduce to crystallographically equivalent variants of the modes given in Tables I and 11, respectively, or become twinning modes with both shear planes as symmetry planes in the cubic lattice and hence not considered in Tables I and 11. With the exception of this last type of mode only those tetragonal twinning modes which reduce to modes 1.1, 1.2, 2.1, and 2.2 of Tables I and I1 are considered in Tables 111 and IV. For values of y in the range -y = 1 to 1.09 the tetragonal modes and the corresponding cubic twinning modes have approximately the same magnitude of shear. The twinning modes listed in Tables 111 and IV are therefore by the criteria given above the most

Jan 1, 1969

By Edwin Ludlow

T HE OPEN FORUM on this subject called by Mr. Hoover at the recent meeting of the Institute&apos; brought out a large number of very able papers, and a very full discussion of all the problems involved. The criticisms of the bituminous industry were: 1. That it was over-developed with the possible output nearly 50 per cent. in excess of the present requirements; that during the summer there were plenty of cars and no orders, and during the winter there were plenty of orders but no cars. 2. That the mines were not properly developed from an engineering standpoint, and that the recovery of the coal varies from 50 per cent. to 95 per cent. 3. That this industry, employing over 600,000 men, could, if running full time, release 100,000 men for other work. 4. That the studies made by the engineers of the Fuel Administration showed that the cost of production increased with a loss of time and that with a 50 per cent. operation the increase in cost was about 40 per cent.

Jan 1, 1920

The sudden and untimely death of Dr. Charles R. Van Hise, late&apos; president of the University of Wisconsin, was one of the greatest losses, not only to the educational world and science of geology, for which he was a great leader and pathfinder, but also to the world of mining and allied interests, for which he was an adviser and helper who blazed trails and pointed out paths of development, which the practical men of englneering and industry will follow long after his death. To the general public, Dr. Van Hise stood as a great educator who conceived and wrought out a new idea in the people&apos;s university .of .a commonwealth and as a great active mind that could not be held within the bounds of education and science but, by its own bigness and broadness, was forced into the contemplation of the larger affairs of the nation. To the engineering profession, dr. Van Hise will be remembered as a tireless worker who solved some of the most complex problems in geolpgy and the development of mineral resources and recorded these findings In a form that is of lasting value to those who follow him in similar labor. In this combination of thinker and worker, educator and economic student, scientist and practical engineer, lies Dr. Van Hise&apos;s contribution to his generation. As an educator, Dr. Van Hise attained perhaps his widest recognition, for in the University of which he was president he evolved and accomplished a new idea, which caused it to be called, in 1908, by President Eliot of Harvard, "the leading State University." At the time of his death, Nov. 19, 1918, he was just completing fourteen years as president and forty-three years as student and teacher in the University. His entire life of 61 years had been devoted to his State and its University. He was the first alumnus of the University and the first Wisconsin-born citizen to become its president—and he enjoyed the longest term as president of the institution. Since his graduation from its College of Engineering in 1879, he had been constantly a member of its faculty. As Chief Justice John B. Winslow, of the Wisconsin Supreme Court said at the time of President Van Hise&apos;s death, " Wisconsin has had many able sons, men who have served their Country and their State with ais-tinguished honor in various fields of effort, but among them all none, I believe, has rendered greater service in his time than President Van Hise. The University will be his true monument, for to him, more than to any one person, we owe the present commanding position of that, great Institution." What his "new ideal of a State University" was maybe best expressed in the words which he used to outline it in his inaugural address in 1904. "I shall never be content until the beneficent influence of the University of Wisconsin reaches every family of the State. This is my ideal of a State University. When the University of Wisconsin attains this ideal, it will be the first perfect State University.... The University of Wisconsin desires to prevent that greatest of all economic losses to the State, the loss of talent. To prevent this loss of talent, the University must not only provide for those who come to Madison for instruction, but must go out to the people of the State with the knowledge which they desire and need." Hence it was said early in his administration that "the boundaries of the State are the campus fence."

Jan 1, 1920