Search Documents

By W. David Menzie

An inventory of the mineral resources of a region is a most desirable basis for planning their systematic development. In the absence of appropriate samples upon which to base a reliable estimate of this inventory, investigators have resorted to a number of indirect approaches; the unit regional value concept forms the basis for one such approach. The produced resources of a region are a function of the inventory multiplied by the degree of intensity (some fraction between zero and one) of development of the resources. A convenient means of expressing this amount is to accumulate the weight and value of resource and to prorate the totals over the area represented by the unit sampled; i.e., weight and value per unit area or tonnes/km.2 and U.S. 1967 $/km.2. When this approach is used for the U.S.A., South Africa and Rhodesia the average value of (log.) U.S. 67$/km.2 for the states of the U.S.A. and South Africa are similar ($55,176 U.S.$67/km.2 and $52,538/km.2 respectively); whereas, Rhodesia is relatively underdeveloped (10,301 U.S.67$/km.2). On the other hand if the individual commodities are used as a basis for comparison, the U.S.A. shows the greatest diversity (67 commodities out of a possible total of 75) with South Africa next (50 commodities) and Rhodesia last with only 26 commodities. Since it is known that area and value are not simply related perhaps diversity is directly related to area. Again the kinds of commodities which have contributed the greatest value to the totals differs, with fuels (petroleum, coal and natural gas) predominating in the U.S.A. totals; whereas, South Africa and Rhodesia obtain their greatest contributions from gold, diamonds (S. Africa) coal and asbestos. In each case the greatest value of resources is produced from sedimentary rocks. As a somewhat different kind of example, consider a single resource (petroleum, the most valuable in the U.S.A.) over a large area (number of sampling units) the U.S.A. by state. Furthermore, assume that the model frequency distribution of the amount of petroleum (tonnes/km.2) is log normal. Then the present production fails to match the model first because 17 states (34% out of 50) have not produced petroleum. Of the remaining 33 states, Louisiana has produced the most (15,177 tonnes/km.2) and the frequency histogram is still skew. A spatial analysis of the distribution of the amount of petroleum by state shows that the samples (i.e., states) are not random; the non-producers and producers tend to cluster. It remains to be seen if this is indeed a true representation of the incidence of petroleum or is a function of the exploration philosophy currently in vogue.

Jan 1, 1977

By M. M. Neale

The pottery department has been aptly described as the "heart of the zinc plant," md every operator of a horizontal-retort plant is acquainted with the fact that good retort practice is the keystone of the smelting process. Since retorts and condensers are clay products, it is obvious that improvements in other branches of the ceramic industry should be observed for possible adoption in the pottery process for zinc smelting. Deaeration of clay bodies is one of the improvements that have become fully, established in many brick and pottery plants. Our investigation of a number of these installations always yielded the same answer—improved practice. Improvement in workability, elimination of laminations, less porosity, greater wet and dry strength, were among the claims put forth for this process. All of these features are exceedingly desirable characteristics in the manufacture of a zinc retort. A preliminary test, which involved truck transportation of deaired slugs over a relatively long distance, did show the value of many of these characteristics in forming the retort. Results from the standpoint of , longer retort life in the smelting furnace were not outstanding. The idea lay dormant for several years but was revived again in 1940, when it was decided to make whatever changes were necessary in the equipment for pottery manufacture to fully demonstrate the process. A number of the manu- facturers of machinery for clay work were asked to submit proposals, and the plan finally adopted was extremely simple and economical. Machine FOR DeaeRRATING Selection of the ''Straight-line'' principle for conversion of the "Wettengel" pug mill to a ''vacuum-extrusion" machine preserved some usable parts of the original equipment, such as the drive mechanism, and main shaft. The converted machine consists of a feed hopper, a compression and shredding zone, a vacuum chamber, and an extrusion barrel, as shown in Fig. I. In operation the clay mix travels from the feed hopper into the compression zone, where it is compressed and finally forced around the tapered cone into the vacuum chamber. As it enters this chamber the clay body is shredded into thin plates, for exFosure to the vacuum. The shredder consists of a hub mounted on the main shaft, to which are bolted segmental sections, each of which carries shredder knives. The compression zone and extrusion barrel function as seals for the vacuum chamber and the shredded clay mix is agitated thoroughly during its exposure to the vacuum. A vacuum pump, equipped with a 3-hp. motor, is attached to this chamber, and maintains 25 to 26 in. vacuum during operation of the mill. Changes in Practice Prior to the adoption of the deaeration process, our standard pottery practice called for double mixing in the combination 7

Jan 1, 1944

By John Wulff, Richard P. Seelig

The importance of the pressing operation in the forming of articles by powder metallurgy depends to a great extent on the type of product to be made. While in some few cases the pressing is merely a means of compacting loose powder particles into a solid mass preliminary to a sintering treatment, in most applications it constitutes a molding operation with the purpose of shaping the raw material in powder form into a certain predetermined, accurately defined part not altered in shape by subsequent sintering. In still other cases, no pressing at all but sintering in molds gives useful articles. A limited number of products are made by the simultaneous application of pressure and heat. The factors that control the product of the pressing operation are raw material, lubricant, type, size and shape of die and compact, magnitude and time of application of pressure, as well as temperature of pressing. All such factors need to be controlled; yet, depending on the function of the pressing operation, greater emphasis may be placed on processing factors other than the pressing operation. In any complete discussion of pressing, subsequent sintering cannot be disregarded. For the sake of brevity, the present paper has been limited to the mechanics of pressing and only occasionally refers to sintering. For the same reason, hot-pressing has been omitted as beyond the scope of this paper In any survey of the literature on the pressing of metal powders, the 1938 paper of Balshinl on the theory of the process of pressing deserves mention. The first attempts at an interpretation of pressing phenomena were made by Balshin' and RakovskL2 The experimental results of both are of great interest. Since the experimental results are not described, the work was repeated, using our own interpretation of the possible techniques, and is reported in the following pages. The basic theory of Balshin,' based on a hydro-dynamic analogy, however, leads to hut another way of plotting density and pres- , sure against height of a pressed compact. Since it does not give any new insight into the phenomena, nor account for the influence of side-wall friction, a discussion of the theory has been omitted from this paper. Density Gradients in Compacts The process of pressing metal powders in a die (disregarding for this consideration the powder filling and ejection operations) may be divided into three phases: (I) packing, (2) elastic and plastic deformation, (3) cold-working with or without fragmentation. It must be emphasized that these three steps do not follow each other in sequence; on the contrary, in practice

Jan 1, 1946

By John Wulff, Richard P. Seelig

The importance of the pressing operation in the forming of articles by powder metallurgy depends to a great extent on the type of product to be made. While in some few cases the pressing is merely a means of compacting loose powder particles into a solid mass preliminary to a sintering treatment, in most applications it constitutes a molding operation with the purpose of shaping the raw material in powder form into a certain predetermined, accurately defined part not altered in shape by subsequent sintering. In still other cases, no pressing at all but sintering in molds gives useful articles. A limited number of products are made by the simultaneous application of pressure and heat. The factors that control the product of the pressing operation are raw material, lubricant, type, size and shape of die and compact, magnitude and time of application of pressure, as well as temperature of pressing. All such factors need to be controlled; yet, depending on the function of the pressing operation, greater emphasis may be placed on processing factors other than the pressing operation. In any complete discussion of pressing, subsequent sintering cannot be disregarded. For the sake of brevity, the present paper has been limited to the mechanics of pressing and only occasionally refers to sintering. For the same reason, hot-pressing has been omitted as beyond the scope of this paper In any survey of the literature on the pressing of metal powders, the 1938 paper of Balshinl on the theory of the process of pressing deserves mention. The first attempts at an interpretation of pressing phenomena were made by Balshin' and RakovskL2 The experimental results of both are of great interest. Since the experimental results are not described, the work was repeated, using our own interpretation of the possible techniques, and is reported in the following pages. The basic theory of Balshin,' based on a hydro-dynamic analogy, however, leads to hut another way of plotting density and pres- , sure against height of a pressed compact. Since it does not give any new insight into the phenomena, nor account for the influence of side-wall friction, a discussion of the theory has been omitted from this paper. Density Gradients in Compacts The process of pressing metal powders in a die (disregarding for this consideration the powder filling and ejection operations) may be divided into three phases: (I) packing, (2) elastic and plastic deformation, (3) cold-working with or without fragmentation. It must be emphasized that these three steps do not follow each other in sequence; on the contrary, in practice

Jan 1, 1946

By J. G. Giddings, R. Kobayashi

Residual viscosity, the ViSCOSitY at a given pressure and temperature minus the dilute gas viscosity at the same temperature, has been found to be independent of temperature for pure components and mixtures for simple molecules and light hydrocarbons. The residual viscosities for methane, ethane, propane and four mixtures were correlated as a function of reduced density and molecular weight. INTRODUCTION Earlier efforts in correlating the viscosity of light hydrocarbons and associated gases under pressure, primarily by some form of the corresponding states principle, have been reported elsewhere.7 The formal theory of corresponding states principle for viscosity from non-equilibrium statistical mechanical arguments for simple molecules has been developed by Helfand and Rice.13 The most serious obstacle to the development of a generalized corresponding states representation of viscosity data, even for simple molecules, has been the limited quantity of precise viscosity data of pure components and mixtures over a wide range of pressure and temperature conditions. Viscosity data on light hydrocarbons have recently been contributed by several laboratories.2,6,8,23,25,26 In the study of the viscosity of nitrogen, Michels and Gibson" observed that the viscosities of nitrogen as a function of density gave parallel isotherms. The same behavior has since been reported for other gases.".= The observed behavior indicates that the residual viscosity or the viscosity at a given pressure and temperature minus the dilute gas viscosity at the same temperature is a unique function of the density. Abas-Zade,1 Michels and Botzen,18 and Michels, Bot-Zen, Friedman and Sengers,19 observed similar behavior for thermal conductivity, the residual thermal conductivity being defined in a manner parallel to that of residual viscosity. Thodos and co-workers 4,15,24 applied the residual viscosity concept to the viscosity of pure monatomic and diatomic gases. Ellington and co-workers10,25 made the residual viscosity vs density plots for ethane and propane, but omitted the region below a residual viscosity of 15 micropoise and showed a systematic separation of the ethane isotherms in the low density region. Eakin correlated the residual viscosity of methane, ethane, propane and n-butane empirically as a function of density and molecular weight: Carmichael and Sage6 recently presented ethane residual viscosity vs density values in the gaseous liquid, and near critical regions as a single univariant function of density. Flynn, Hanks, Lemaire and ROSS" have contributed extremely accurate viscosity data to confirm that the residual viscosity concept is essentially correct, but may not be accurate within 0.1 per cent of the viscosity value for the gaseous state- The recent studies by Giddings12 indicate that the residual viscosity of methane, propane and each of four methane-propane mixtures are unique functions of density Over the temperature and the density ranges studied.

Jan 1, 1965

By John Wulff, Richard P. Seelig

THE importance of the pressing operation in the forming of articles by powder metallurgy depends to a great extent on the type of product to be made. While in some few cases the pressing is merely a means of compacting loose powder particles into a solid mass preliminary to a sintering treatment in most applications it constitutes a molding operation with the purpose of shaping the raw material in powder form into a certain predetermined, accurately defined part not altered in shape by sub- sequent sintering. In still other cases, no pressing at all but sintering in molds gives useful articles. A limited number of products are made by the simultaneous application of pressure and heat. The factors that control the product of the pressing operation are raw material, lubricant, type, size and shape of die and compact, magnitude and time of application of pressure, as well as temperature of pressing. All such factors need to be con- trolled; yet, depending on the function of the pressing operation, greater emphasis may be placed on processing factors other than the pressing operation. In any complete discussion of pressing, subsequent sintering cannot be disregarded. For the sake of brevity, the present paper has been limited to the mechanics of pressing and only occasionally refers to sintering. For the same reason, hot-pressing has been omitted as beyond the scope of this paper. In any survey of the literature on the pressing of metal powders, the 1938 paper of Balshin1 on the theory of the process of pressing deserves mention. The first attempts at an interpretation of pressing phenomena were made by Balshin1 and Rakovski.2 The experimental results of both are of great interest. Since the experimental results are not described, the work was repeated, using our own interpretation of the possible techniques, and is reported in the following pages. The basic theory of Balshin,1 based on a hydro- dynamic analogy, however, leads to but another way of plotting density and pres- sure against height of a pressed compact. Since it does not give any new insight into the phenomena, nor account for the influence of side-wall friction, a discussion of the theory has been omitted from this paper. DENSITY GRADIENTS IN COMPACTS The process of pressing metal powders in a die (disregarding for this consideration the powder filling and ejection operations) may be divided into three phases: (I) packing, (2) elastic and plastic deformation, (3) cold-working with or without fragmentation. It must be emphasized that these three steps do not follow each other in sequence; on the contrary, in practice

Jan 1, 1946

By L. B. Herring, Harold Decker

The area under discussion includes districts 2 and 4, so designated by the Texas Railroad Commission,‡ and comprises the following 26 counties: Bee, Brooks, Calhoun, Cameron, De Witt, Duval, Goliad, Gonzales, Hidalgo, Jackson, Jim Hogg, Jim Wells, Karnes, Kenedy, Kleburg, Lavaca, Live Oak, Nueces, Refu-gio, San Patricia, Starr, Victoria, Webb, Willacy, Wilson and Zapata. Drilling and Production The total number of wells drilled in this district during 1944 is shown in Table 5. This indicates a 41 per cent increase in all drilling over 1943. In spite of every handicap created by the war, the oil industry more than met the crisis in its drilling program in this district. Last year we thought it would be impossible to add to the total number of wells drilled in the previous yea;, but in spite of the lack of manpower and materials this large increase was shown. During 1944 this district produced 124,201,978 bbl. of oil from 11,607 producing wells, whereas in 1943 it produced 88,421,693 bbl. from 11,211 producing wells. This is an increase of 35,780,285 bbl. of oil. Some decline has been shown in the older fields arid undoubtedly the majority of wells in the district are producing at too high a rate. However, this district has been able to meet any demands made on it by the Petroleum Administration for War for increased production. Discoveries and Extensions There was a slight decline over the preceding year in the number of wildcats drilled, but the number of discoveries increased. In most instances subsequent development has not been sufficient to arrive at preliminary valuations but it appears that the over-all oil discoveries were below normal and that the gas discovcrics were relatively more important. The Canolis and Tijerina pools, Jim Wells County, and the Dan Sullivan pool, Brooks County, appear to be the outstanding oil discoveries of the year. No important oil reserve was discovered or developed in the Wilcox horizons, although considerable wildcatting was done. Important extensions were made at Agua Dulce and Stratton in Nueces and Teleberg Counties. Production was increased appreciably at Willimar, Willacy County, and Seeligson, Jim Wells County, in sands and areas which were apparently productive at the beginning of the year. Refining Most of the major work in the changing and completing of refineries was finished this past year. Some of the most modern refineries in the industry are now located in the Corpus Christi area. Gas and Condensate No new recycling projects were commenced during the year, nor were there any important additions to the old operations. No major gas reserve was developed, although several new discoveries suggest potentid possibilities.

Jan 1, 1945

By Frederic Benard

PRIOR to 1936, the Ontario Refining Co. received all incoming blister copper from The International Nickel Company's smelter in the usual form of 460-lb. cakes, or slabs. These were received in open cars in lots of 250 pieces. At the refinery the cakes were unloaded onto narrow-gauge cars, for convenient handling and pickup by charging cranes. In March 1936, an investigation was started on the feasibility of trans-ferring converter copper in the molten state from the smelter to the refinery anode furnaces, a distance of 114 miles. Although common in steel practice, the transportation of blister copper in this form had not previously been attempted and a preliminary study of the various factors involved was therefore necessary. For this purpose, a series of experiments was made in which molten copper, removed at different stages during the furnace cycle, was held in a small portable holding furnace. This vessel was essentially a refractory-lined steel cylinder provided with ports for filling and emptying, heated by an oil burner. Dimensions of the steel shell were 3 ft. 10 in. diameter by 7 ft. 3 in. long, and thickness of refractories depended oil the design and combination used for the particular experiment. The vessel was filled with approximately 2 ½ tons of copper at a predetermined temperature, the lining having been preheated to a definite point by means of an oil burner. All openings were well luted and temperature readings were made every 15 min. by means of an immersion-type thermocouple. In this manner the rate of heat loss resulting with different refractory design could be developed. The ratio of exterior surface to weight of metal was taken into consideration in comparing the experimental results with what might be expected for a full-sized unit, and observations were also made on type and degree of slag accretion. It was not possible to get as much information on this latter point as desirable, but all evidence showed that the problem would be control of slag build-up rather than attack oil refractories.

Jan 1, 1938

By George Macready

TRINIDAD, British West Indies, is an island near the north coast of South America, situated between latitudes 10° and 11° N:, and. opposite the numerous outlets of the Orinoco River Delta. It is separated from Venezuela by the Gulf of Paria (salt, water) and straits over 5 mi. (8 km.) wide. The area of the island is approximately 1750 sq. mi. (453,- . 250 hectares) and the population is approximately 400,000. The climate is tropical with an annual rainfall of from 45 to 60 in. (114 to 152 cm.). The oil fields consist of several units, or fields, located in the southern half of the island. Approximately 90 per cent. of the total production has been yielded by fields situated within 7 mi: (11.3 km.) of the famous asphalt lake and on the southwest peninsula. The most important producing fields, or units, are the following, which are shown on the accompanying map: Brighton, or Pitch Lake Field, operated by the Trinidad Lake Petroleum Co., Ltd., is situated beside the famous Pitch Lake; it, even encroaches on the lake. Vessigny Field, operated by the Trinidad Lake Petroleum Co., Ltd., is situated 2 mi. (3.2 km.) south of Pitch Lake. Lot One Field, operated by the Petroleum Development Co., Ltd., the United British Oilfields of Trinidad, Ltd., and Stollmeyer, Ltd., is situated 3 mi. south of Pitch Lake upon Lot One of Morne 1'Enfer Forest Reserve and adjoining properties. Parry Lands Field, operated by the United British Oilfields of Trinidad, Ltd., and the Petroleum Development Co., Ltd., is situated 3;2 mi. south of Pitch Lake on Lot Three of Morne l'Enfer Forest Reserve and adjoining properties. Point Fortin Field, operated by the United British Oilfields of Trinidad, Ltd., is situated at Point Fortin, 6 mi. southwest of Pitch Lake. Fyzabad Field, operated by Trinidad Leaseholds, Ltd., is situated several miles southwest of Fyzabad Village and 6 mi. south-southeast of Pitch Lake. Barracpore Field, operated by Trinidad Leaseholds, Ltd., is situated several miles south of. San Fernando and 15 mi. (24.14 km.) east of Pitch Lake.

Jan 9, 1920

By J. V. Gluck

In the present paper," as in earlier publications, V1'2"1 the authors present experimentally obtained relations for the free energy of solution of oxygen in various metals as a function of temperature. The relations are linear and given in slope-intercept form. The authors give values for the "probable error" of the slope and intercept, citing Birge's method17 for obtaining these quantities. Birge discussed these methods as early as the period 1929-32.25726 In Ref. 25 the probable error is defined as "the numerical value which the true error is as likely to exceed as not", i.e., 50 pct probability. Ref. 26 is even more detailed and includes a lengthy discussion of the applicability of the Gaussian distribution to experimental data. However, the use of the "probable error" has come under some question. For example, Ezekiel'~ states that "the use of the probable error tends to make the results appear rather more accurate than the standard error". Moroney28 stated (in 1951) that "the term 'probable error' was used in former times to denote 0.67450 (50 pct confidence using the normal distribution)....the term, a poor one, is now very much obsolescent. It has been said that 'it is neither an error nor probable' ". Bennett and Franklin in 1954" in discussing statistical confidence levels mentioned that "the customary use of the 5 and 1 pct levels is not completely a matter of chance; these levels probably represent a balance between the desire to be correct and the desire to be specific. Also in most people's minds the borderline between something that could possibly happen and something that is not likely to happen is somewhere in this region. Certainly 5 or 1 pct confidence limits are to be preferred to limits such as the 'probable error' which has only a 50/50 chance of including the correct value." It may readily be seen that the 95 pct confidence level, which is given by 1.960 (assuming large sample size), thus corresponds to approximately three times the "probable error". Indeed, limits of one standard deviation correspond only to about 68 pct probability. Even if we triple the tolerances given by the authors in the equations of their Table 111, the deviations do not become excessive and would not detract from their excellent results. It could then be said with a high degree of confidence (95%) that the precision of the slope and intercept values is about *3-5 percent of their absolute levels rather than the 1-2 percent implied in Table 111. This is then compatible with an earlier suggestion of Gokcen~' of a probable accuracy of 5 pct in dissolved oxygen measurements by the technique employed. Alternatively, the authors could have

Jan 1, 1967

Prospectors were digging silver in the Ray mine area in 1873, and by 1880 high-grade copper ore was feeding a 30-ton copper furnace. In 1910, D. C. Jackling and his associates organized the Ray Consolidated Copper Company, known in mining circles as Ray Con, to exploit the Ray orebody. For 50 years, all mining was underground and the Ray mine was known the world over for innovations in mining methods. It was the first to mine important tonnage (8,000 tpd) by block caving methods. The mill at Hayden, 26 miles (41.6 km) from the mine, kept pace with the new mining methods developed at Ray and in the early 1920's flotation replaced gravity concentration by the vanner machines. First mining by open pit methods began in 1950 and in January 1955 all underground mining was discontinued. The new primary crushing plant, installed in early 1967, featured design simplicity with a low capital cost. The 54 in. gyratory crusher was installed within a total height of 6 1 ft (18.65 m) from the truck dump road bed to the floor beneath the feeder-conveyor under the surge pocket. The crusher is fed by 120-ton trucks dumping from one side only into a 200-ton hopper equipped with a horizontal splitter bar to protect the crusher spider. The crushed ore pocket, of 120 -ton live capacity underneath the crusher, discharges to a 0 to 200 fpm (61.2 mpm), variable-speed, 72 in. by 80 ft long (1.83 m by 24.4 m) sloped belt feeder, probably a first in the industry. Wood-picking stations are provided on either side of the belt so that old mine timbers and tramp iron can be removed from the crushed ore and the wood can be dropped into Dempster containers located below the belt. Counter-weighted finger gates control the bed depth on the belt at 14 in. (356 mm) and a low- level radiation unit automatically maintains a minimum of a 3 ft bed (900 mm) of material on the belt directly under the surge pocket. The conveyor is skirted for its full length and is approximately 60 in. (1.52 m) wide inside its metal skirt liners. Ten impact idlers at 12 in. (305 mm) spacing are provided under the loading pocket and remaining idlers are spaced at 18 in. (457 mm). The belt is 1 ¼ in. (31. 8 mm) thick; and, while it has occasionally been damaged by tramp material, belt life averages 11 million tons. When the belt is changed, the coiled new belt is lowered into position onto one of two belt stands mounted over the feeder, the old belt is cut, and one end is attached temporarily to the new belt. The other end of

Jan 1, 1978

By W. J. Reagan

THE problem of increasing output and decreasing percentage of rejections is a vital one in the manufacture of steel of any kind. The making of basic open-hearth steel for use in rolled steel wheels, tires for locomotive and car wheels, and forgings of various kinds, is a highly specialized industry. The increase in weight of railway rolling stock of all kinds, and the high speed that the public demands of transportation facilities, make it imperative that steel for use in this class of material shall be of the highest quality obtainable. During the past few years it has been the writer's good fortune to have opportunity-to study the defects in basic open-hearth steel, and also the results obtained by various changes in open-hearth practice, on such defects. The opportunity for study and the details available are rarely found in the manufacture of steel of any kind. It seems reasonable to assume that many of the results determined here can be applied to the production of steel of other types with a decided improvement in quality, a decrease in the percentage of rejections and an increase in output. All of the material described is basic open-hearth steel with the following range of analysis: carbon, 0.50 to 0.85 per cent.; phosphorus and sulfur, 0.04 coax.; silicon, 0.15 to 0.35; manganese, 0.50 to 0.75. All of this material is bottom-cast, therefore tapping and pouring temperatures are higher than in top-cast production. Ingots used in this type of work are of standard length with varying diameters. The ingot is known as duodecagonal, or twelve-sided. The standard body length is 88 in. and the hot top length, 14 in. Fig. 1 shows a typical ingot of this type. The diameter varies from 13 to 30 in. Ingots for special forgings, which cannot be made in molds of standard size, are made in molds of various sizes and designs. These ingots are sliced cold, into blocks of various lengths, depending upon the weight of the forging to be made. Fig. 2 shows the ingot-after coming from the slicing lathe. Just sufficient metal remains between blocks to hold the ingot in one piece while it is being removed from the lathe; then steel wedges are inserted between the blocks and the blocks are broken apart. This affords abundant opportunity for inspection, as the interior of the

Jan 1, 1930

By M. J. Blackburn

The phasal equilibria in TI':Al alloys has been studied Ry transmission electron microscopy, electron diffraction, and X-ray diffraction. It is shown that three-phase fields exist below the transformation, viz.: a disordered hexagonal solid solution a; an ordered hexagonal phase based on Ti3Al, aa; and a two-phase region. (a + (YZ) , occurring between the single-plzuse fields. The size. disiribution, and morphology of- the a, phase in the two-phase region is shown to be dependent upon the alloy composition and heat treatement. The ordering process in the a, phase leads to the formation of anliphase domain boundary networks; the contrast and stability of these networks is shown to be dependent on alloy composition. A new and relatively simple phase diagralil for the systemm is constructed. The phasal equilibrium at the titanium-rich end of the Ti:Al system has long been the subject of considerable controversy. crossleyl has recently reviewed the phase diagrams that have been advanced for the system and in his turn proposed yet another one. There would seem to be general agreement that a phase exists at a composition at or near Ti& with an ordered hexagonal DO,,-type structure. However, several other phases have been proposed; for instance, Ence and ~ar~olin's' diagram includes two phases, Ti2A1 and Ti3A1, in the region up to 25 at. pct Al. The position of the proposed phase boundaries varies over a considerable compositional and temperature range, a point graphically illustrated in Fig. 1 of Crossley's paper.' It is perhaps germane to briefly examine the techniques used by other workers in the establishment of the phase structure. These fall into three categories: 1) X-ray diffraction, the only limitation of which is the rather low intensity of superlattice reflections in this system.3 Thus, superlattice reflections become increasingly difficult to detect in the more dilute aluminum alloys. 2) A considerable amount of optical microscopy has been performed"2'4 and it will be shown in a later section that many of the obscure mi-crostructures that have been observed can be attributed to hydrogen contamination. It is concluded, therefore, that such observations should be interpreted with considerable care. 3) The variation of some physical property with aluminum content has been measured.5"7 These methods are a useful indication of the existence of a transformation, but are usually insufficient in themselves to identify the transformation. The results using these techniques will be considered in more detail in the discussion. In this paper, the phase structure of alloys containing up to 25 at. pct A1 has been studied by transmission electron microscopy and X-ray techniques, and the results are used to generate a new and relatively simple diagram for the titanium-rich end of the Ti:Al system. EXPERIMENTAL A series of alloys containing 5.05, 10.16, 13.39, 13.99, 14.40, 20.83, and 25.05 at. pct A1 were obtained in the form of hot-rolled sheet 0.02 in. thick. These alloys contained 0.10 to 0.15 pct 0. Thirty-gram arc-melted buttons were prepared from iodide titanium and 99.99 A1 which contained 16.1, 16.9, 18.2, 19.0, 21.6, 22.2, 23.0, and 23.9 at. pct A1 and had an average oxygen content of 0.03 pct 0. The differences in oxygen content did not appear to influence the nature of the phase transformations which were found. Oxygen content may affect the temperature of these transformations, but insufficient samples of the high-purity alloys were examined to answer this question. The heat treatment of alloys was performed in dynamic atmosphere and vacuum furnaces or in helium -filled silica capsules. A special vacuum furnace was constructed to provide a high quenching rate in which rates of 4000°C per sec were obtained using water as the quenching medium. As pointed out by Crossley,' it is important to avoid heat treatment in the a - [} phase field as the resultant segregation of the alloy into the two phases containing different amounts of aluminum can persist through subsequent treatments leading to ambiguous results. It will be demonstrated later that step cooling of specimens from the a phase region can also lead to anomalous effects. Thus, all solution treatments were carried out in either the a or 3 phase fields followed by water quenching and subsequent isothermal annealing at various temperatures. X-ray analyses were performed on a diffractometer on fine-grained bulk specimens. The value of long-range order parameter, S, wa_s calculated from the integrated intensity of the (1211) reflection. In general, the intensity of the (1011) superlattice reflection was compared with that of the (2021) fundamental reflection to correct for experimental differences between measurements. Thin foils for electron microscopical examination were produced by electropolishing using the technique described in an earlier paper.8 Dark-field techniques were employed to a large degree in this investigation using the gun-tilt method. Finally it should be noted that the lattice parameters of the D01,-type superlattice are approximately related to the disordered hexagonal phase parameters by Crf - c, and 2ad - a, where the subscripts s and d refer to the ordered and disordered unit cells, respectively.

Jan 1, 1968

By I. L. Dillamore

I. L. Dillamore (University of Birmingham)—The different textures developed in various fcc metals have long awaited satisfactory explanation and it has now become clear that these differences are related to parallel differences in the deformation characteristics of the metals. Liu is correct, therefore, in seeking to account for the observed textures in terms of the flow mechanisms but I believe, for the reasons outlined below, that the particular interpretation of flow mechanisms proposed by Liu is open to substantial objections. By considering the forty-eight possible designations of the twelve octahedral slip systems found in fcc metals as distinct and separate deformation modes, Liu has fallen into the error of assuming that only positive glide dislocations associated with each system are present. In fact both positive and negative dislocations will be present and the only difference between for instance the systems B4 and B4' (in Liu's notation) is that under a stress of given sign the direction of motion of a dislocation is reversed on changing from B4 to B4'. For both orientations positive and negative dislocations will be present. In considering possible dislocation interactions it is, therefore, inadmissible to differentiate between R4 and R4' as Liu does. Liu considers those dislocation interactions which give the biggest reduction in energy to be the most favorable and neglects, on the grounds that they will form strong barriers to slip, interactions between dislocations with perpendicular Burgers vectors. Setting aside interactions between positive and negative dislocations of the same slip system, which must occur regardless of the combination of slip systems chosen, the biggest reduction in energy occurs for the Lomer-Cottrell interaction and it is Lomer-Cottrell barriers which are thought to provide the stronger dislocation obstacles. On the other hand the intersection of dislocations with perpendicular Burgers vectors is thought to be a low-energy process which contributes only a fairly small temperature-dependent part of the total work hardening. On this basis it seems doubtful whether the reduction in energy through possible dislocation interactions provides a reasonable criterion for choosing the operative slip systems. From the point of view of texture development it is unsatisfactory to ignore the slip rotations leading to an end position and to neglect to consider the stability of the chosen end point. It is also unsatisfactory to treat the two stress axes as interchangeable since, if the stress system is idealized as biaxial, one stress is compressive and the other is tensile. For the same reason the rotations of the two stress axes are not made compatible simply by assuming that the same slip directions are responsible for the rotations of the two stress axes. It is, in short, essential to treat the two stress axes as acting together on the same slip systems. Turning to the question of the difference between the copper-type and the brass-type texture, there now remains little doubt that the difference is attributable to differences in stacking-fault energy (y), as noted by Liu, but it is doubtful whether the temperature dependence of the texture in copper and in silver is due to increasing stacking-fault energy with increasing temperature. The results of Swann and Nutting42 cited by Liu were obtained in Cu-A1 alloys and the apparent increase in stacking-fault energy on raising the temperature may be influenced by short-range ordering. In pure metals such effects are absent and the only data available on the variation of y with temperature are those of Buhler et a1.43 for silver. They report a minimum at 200°C which does not fit the hypothesis put forward by Liu. It is much more likely that thermal activation of cross slip is important in determining which texture develops, as proposed by Dillamore and tors. These workers have proposed an explanation for the differences in observed texture among the fcc metals and the pole figures predicted consist of an orientation spread which is in better agreement with observation than the limited number of discrete orientations suggested by Liu. The theory of Dillamore and Roberts is also able to account for the differences between aluminum and copper which Liu still leaves unexplained. Y. C. Liu (author's veply)—The writer appreciates the interest of Dr. Dillamore, but must discuss some of his comments in order to avoid cross purposes. The phrase, "forty-eight slip systems," which appeared twice in the text—in the caption of Fig. 1 and the first paragraph in the Discussion—might unfortunately have led Dr. Dillamore to disagree

Jan 1, 1965

By Nicholas J. Grant, Olaf Troili, John Chipman

D. C. Hilty (Union Carbide & Carbon Research Laboratories, Niagara Falls, N. Y.)—How does this effect of silica compare with the effect of silica in combining with the lime in the slag to reduce the activity of CaO, thereby affecting the first equation? John Chipman(authors' reply)-—That is the object of showing this effect for slags of two different basicities. In the more basic, the silica is more firmly tied up in the slag and is less easily reduced. It is therefore less able to interfere with desulphurization. The important point is that silica is acting in two ways. Of course it is an acid and as an acid it ties up lime and in tying

Jan 1, 1952

By O. F. Thornton, D. L. Marshall

Results of the determination of the inter stitial water content of several core samples from oil reservoirs are presented. Data obtained by the capillary pressure method, which has recently been developed, are compared with water saturations measured in cores cut with oil-base mud and with values calculated from the electrical resistivity of the formation. The agreement between the capillary pressure and other methods, combined with the fact that similar agreement has been obtained by others, indicates that the capillary method properly applied yields results sufficiently accurate for most engineering purposes. In some cases, it may be possible to extend the utility of data obtained with the capillary pressure method by correlation of interstitial water saturation with more easily measured physical properties of the media. Introduction Several methods are in use for determining or for estimating the interstitial water saturation at given points within oil and gas reservoirs. The direct measurement of the water content of cores obtained with nonaqueous fluid in the hole is believed to be an accurate method under most conditions. The water saturation may be calculated by use of the resistivity curves of the electric log,' although this method is not applicable under conditions that exist in some reservoirs. Recently, a method has been developed and described3.' wherein the interstitial water saturation of cores is measured at a capillary pressure such that conditions existing in the reservoir are simulated. The purpose of this paper is to present data obtained by use of this latter method, and to compare the results obtained with determinations made by other means. Method The theory underlying the capillary pressure method applied to petroleum reservoirs has been discussed adequately in the literature by Garrison,2 Leverett,5 and Others.3,6,7 Briefly, and simply, capillary pressure is defined as the difference in pressure between two contacting fluid phases, such as oil and water. For the simplified sand, water and oil system illustrated in Fig I, the pressure difference can be stated as follows:6 where Pc is the capillary pressure in pounds per square inch, ? is the interfacial tension between oil and water in pounds per inch, r1 and r2 are the radii of curvature of the interface between oil and water in inches. Capillary pressure varies in a given reservoir with depth because of the greater density of the water phase as compared with oil or gas. The following equation expresses the difference in pressure between two points: p1- p2 - h?p/144 [2] where p1 — p2 is the capillary pressure difference in pounds per square inch, h is

Jan 1, 1947

By D. L. Marshall, O. F. Thornton

Results of the determination of the inter stitial water content of several core samples from oil reservoirs are presented. Data obtained by the capillary pressure method, which has recently been developed, are compared with water saturations measured in cores cut with oil-base mud and with values calculated from the electrical resistivity of the formation. The agreement between the capillary pressure and other methods, combined with the fact that similar agreement has been obtained by others, indicates that the capillary method properly applied yields results sufficiently accurate for most engineering purposes. In some cases, it may be possible to extend the utility of data obtained with the capillary pressure method by correlation of interstitial water saturation with more easily measured physical properties of the media. Introduction Several methods are in use for determining or for estimating the interstitial water saturation at given points within oil and gas reservoirs. The direct measurement of the water content of cores obtained with nonaqueous fluid in the hole is believed to be an accurate method under most conditions. The water saturation may be calculated by use of the resistivity curves of the electric log,' although this method is not applicable under conditions that exist in some reservoirs. Recently, a method has been developed and described3.' wherein the interstitial water saturation of cores is measured at a capillary pressure such that conditions existing in the reservoir are simulated. The purpose of this paper is to present data obtained by use of this latter method, and to compare the results obtained with determinations made by other means. Method The theory underlying the capillary pressure method applied to petroleum reservoirs has been discussed adequately in the literature by Garrison,2 Leverett,5 and Others.3,6,7 Briefly, and simply, capillary pressure is defined as the difference in pressure between two contacting fluid phases, such as oil and water. For the simplified sand, water and oil system illustrated in Fig I, the pressure difference can be stated as follows:6 where Pc is the capillary pressure in pounds per square inch, ? is the interfacial tension between oil and water in pounds per inch, r1 and r2 are the radii of curvature of the interface between oil and water in inches. Capillary pressure varies in a given reservoir with depth because of the greater density of the water phase as compared with oil or gas. The following equation expresses the difference in pressure between two points: p1- p2 - h?p/144 [2] where p1 — p2 is the capillary pressure difference in pounds per square inch, h is

Jan 1, 1947

By AIME AIME

The Bulletin. The Bulletin of the Institute will be issued hereafter monthly instead of bi-monthly as heretofore. Among other reasons for this change, it is desired to effect thereby the earlier transmission to members of important papers, lists of candidates tin? membership, and other items of timely information. The New Haven Meeting. As already announced in special circular, the XCVIth meeting of the institute for the reading and discussion of papers will be held at New Haven, Conn., beginning Feb. 23, 1909. The Secretary of the Local Committee is Prof. J. D. Irving, Box D, Yale Station, New Haven. The program embraces visits to many interesting works in New Haven, Ansonia, Bridgeport, etc. The leading topics for discussion at the sessions will lie: The Conservation of Natural Resources; A Sea-Level Canal at Panama; and The Technical Education of Mining Engineers. But papers on other subjects also are announced. Lt is probable that a supplementary session of this meeting, will be held in New York City, at some time during March, 1909, as a joint session with other national engineering societies, for the farther discussion of the subject of The Conservation of Natural Resources. A Pacific Coast Meeting. It is now reasonably certain that the XCVIIth meeting will be held oil the Pacific Coast, including a. visit to the Exposition at Seattle, and various other points en. route going or coming, depending upon the route and program finally adopted. (lore definite information will be announced at the New Haven Meeting, or at the earliest possible date thereafter.

Jan 1, 1909

By John E. Greenawalt

In view of the increasing importance of sintering in the beneficiation of iron ores preparatory to their reduction in the blast furnace, the writer believes the time is opportune for an up-to-date, though brief, discussion of the general principles of sintering, as well as a discussion of some of the recent improvements and mechanical developments that have been achieved in this industry, its present trend and future possibilities. Sintering may be defined as the agglomeration of fine mineral particles into a porous mass by incipient fusion caused by heat produced by combustion within the mass itself. Its first successful application, in connection with the treatment of lead sulphide ores, was known as blast roasting. In this process the lead ore was given a preliminary roasting in a reverber-atory furnace, then the incandescent mass was placed in a pot with a grate and an updraft was applied. It was soon discovered that much better results were obtained by cooling the ore, moistening it, and placing it upon an incandescent layer of fuel previously placed upon a grate, and then applying the updraft blast of air until the charge was converted into a more or less agglomerated mass. The fuel was sulphur and the process one of desulphurization, which was the principal result desired. The application of downdraft to blast roasting brought about tremendous results; the principal one of which was that an air blast of high pressure could be passed through a layer of ore deposited on a grate, or on a grate covered by a layer of coarse porous material, without disturbing the particles of which the layer is composed. The air current is compelled to filter through the pores of the charge, whereas if the same pressure applied to the top surface of the charge with downdraft were applied to the bottom of the charge with updraft, the charge would be completely blow11 off the grate. Another result of reversing the draft was that a flame could readily be applied to the top surface of the charge for igniting purposes. Broadly speaking, sintering is an oxidizing or burning process, therefore the volume of air passing through the charge is the all-important factor. The air must pass through with sufficient rapidity to produce the necessary heat, and if sufficiently rapid the combustiorl will take place

Jan 1, 1938

By John E. Greenawalt

In view of the increasing importance of sintering in the beneficiation of iron ores preparatory to their reduction in the blast furnace, the writer believes the time is opportune for an up-to-date, though brief, discussion of the general principles of sintering, as well as a discussion of some of the recent improvements and mechanical developments that have been achieved in this industry, its present trend and future possibilities. Sintering may be defined as the agglomeration of fine mineral particles into a porous mass by incipient fusion caused by heat produced by combustion within the mass itself. Its first successful application, in connection with the treatment of lead sulphide ores, was known as blast roasting. In this process the lead ore was given a preliminary roasting in a reverber-atory furnace, then the incandescent mass was placed in a pot with a grate and an updraft was applied. It was soon discovered that much better results were obtained by cooling the ore, moistening it, and placing it upon an incandescent layer of fuel previously placed upon a grate, and then applying the updraft blast of air until the charge was converted into a more or less agglomerated mass. The fuel was sulphur and the process one of desulphurization, which was the principal result desired. The application of downdraft to blast roasting brought about tremendous results; the principal one of which was that an air blast of high pressure could be passed through a layer of ore deposited on a grate, or on a grate covered by a layer of coarse porous material, without disturbing the particles of which the layer is composed. The air current is compelled to filter through the pores of the charge, whereas if the same pressure applied to the top surface of the charge with downdraft were applied to the bottom of the charge with updraft, the charge would be completely blow11 off the grate. Another result of reversing the draft was that a flame could readily be applied to the top surface of the charge for igniting purposes. Broadly speaking, sintering is an oxidizing or burning process, therefore the volume of air passing through the charge is the all-important factor. The air must pass through with sufficient rapidity to produce the necessary heat, and if sufficiently rapid the combustiorl will take place

Jan 1, 1938