Search Documents

By J. Q. Ehrgott

INTRODUCTION The U. S. Army Engineer Waterways Experiment Station (WES), under sponsorship of the Defense Atomic Support Agency, has recently developed a unique dynamic high-pressure triaxial testing device (DHT). The device permits acquisition of both axial and lateral deformation data while undisturbed soil and/or rock specimens are subjected to various states of controlled impulsive-type stresses produced by varying both the axial stress and the radial stress rapidly with time. The device is used to develop controlled dynamic pressure pulses within the triaxial chamber fluid on soil or rock test specimens to 3 inches in diameter. Controlled dynamic axial pulse loads are delivered to the specimen by a piston driven by an existing pneumatic ram loader (SECO). The DHT consists of a triaxial cell and a pressure supply and decay system which permits the chamber pressure to be varied with time. Together the DHT and SECO operate in a testing program so as to provide time varying confining pressures and axial loads to test specimens at independently controlled but synchronized programmed rise, hold, and decay times. Rise time is defined as the time from zero load or pressure to peak load or pressure; hold time is the time of constant peak load or pressure; and the decay time is the time from peak load or pressure to zero load or pressure. The maximum dynamic confining pressure attainable is approximately 15,000 psi and the fastest rise and decay times are 3 millisecond (msec) and 20 msec, respectively. This paper presents a description of the DHT, the necessary support equipment, and details of the measurement system. Performance evaluation tests conducted on clay siltstone and a Cretaceous sandstone are presented since the results demonstrate some of the capabilities of the device and show some of its characteristics.

Jan 1, 1971

By Henry Rawdon

THE RELATION between the course, or path, of the fracture of metals and alloys, produced in service or as a result of certain laboratory tests, and the crystalline units of which such materials are composed is of utmost importance. The fracture of normal material is, in general, intracrystalline, i.e., it consists of a break across the grains rather than of a separation between them. An intercrystalline fracture indicates either that the metal is of very inferior quality or that the break occurred under very unusual conditions, e.g., at a very high temperature. The usual mechanical tests, when applied to metals of the type that breaks with an intercrystalline fracture, merely measure the coherence of adjacent grains for one another and reveal little as to the real properties of the metal itself. Even such a soft plastic substance as lead, under suitable conditions, may be rendered so weak and brittle that the metal can be easily crumbled into powder by the fingers although the constituent grains have lost none of the intrinsic properties of lead. Various erroneous explanations of this behavior of lead have appeared in the scientific literature, the change being described usually as an allotropic one. The importance, in an industrial sense, of a proper explanation of this type of the corrosion of lead justifies the description of the type of metal deterioration that follows.

Jan 2, 1920

By Lane Mitchell

A ceramic product or processed material is a solid composed of materials which have been subjected to heat above 875°F. The raw materials, which are blended together (or in some cases used singly), are selected and utilized for various reasons such as ease of fabrication, aid to processing, to yield desired properties after processing, lack or controllable degree of toxicity or hazard, availability, cost, and perhaps other considerations. Almost all solid inorganic, some organic, and some liquid and gaseous materials have the potential to be used individually in some ceramic product. There are several fundamental functions to be fulfilled in every ceramic product and a number of secondary functions are desirable in specified products. These functions are generally met by the most widely occurring minerals and rocks of the earth and their debris. This fact characterizes ceramics as a field utilizing the raw materials most available to man. Of course, specified products utilize synthetics, organics, and rare inorganics to produce desired results. Any solid nonmetallic product processed by subjection to temperature above a red heat may be called a ceramic product. Widely used construction materials and units, domestic utensils and units, industrial parts to facilitate manufacture, technical components, and aesthetic creations are very often of a ceramic nature because of the durability, inertness, hardness, ease of fabrication, cost, and availability of the ingredients. Often, organics or metals cannot meet desired specifications for some of these products. The rocks and minerals and mineral debris of the earth are largely siliceous. Oxygen and silicon comprise roughly 75% of the earth's crust with aluminum, iron, calcium, and the alkalies following in abundance. Silica ( SiO, ) and silicates can be melted to form glasses. Alumina (A1,0,), present in a mineral com- pound, gives greater durability, hardness, and strength, but lessens the glass-forming property. Iron, calcium, and the other alkalies flux silica and reduce melting points. Thus, sand, which is generally almost pure SiO,, and clay, which is generally hydrated alumina silicate, are the most widely used of all ceramic raw materials-principally because of the glass-forming propensities of silicates. In ceramic formulations, clay is generally a refractory filler or skeletal material, having in the raw state a plasticity derived from its colloidal grain size and its water-loving nature. On the other hand, silica sand is a glass former or nonplastic filler. Clay and silica sand in pure forms are quite refractory, i.e., not easily melted. Clay, although siliceous, is less of a glass former than pure silica and is more refractory. Natural contaminants, such as iron oxide or limestone, adulterate many clays and some sands. These contaminants act as fluxes and reduce the fusion points of the mineral or blends. Glass is made from silica sand by fluxing the sand with strong bases, usually soda ash and limestone. Red building bricks are hard and durable because the sand and clay have been partially fused with help of natural iron oxide serving as a flux. The iron oxide per- forms a dual function, serving as a pigment as well as a flux. In a blend of clay and sand and iron oxide, the sand is more susceptible to fusion than is the clay. Although silica sand and clay are the most widely used raw materials in most ceramic products, many other minerals, and some non- minerals are utilized in products where these materials can produce or aid in achieving desired results. Limestone and dolomite, feldspars, pigmentary minerals, refractory oxides or carbides, and special property producers can

Jan 1, 1975

By A. P. Miller, T. S. Washburn

Improved procedure in the manufacture of rail steel has come as the rail user demanded better wearing qualities combined with greater unit weight. With each weight increase per lineal yard has come greater difficulty in making a product that would successfully withstand all tests that modern rails must meet. With these facts in mind, and with a sincere desire to produce a rail whose service in track would be satisfactory in all respects, the steelmaker was quick to realize that all of the factors entering into his process would have to be more closely controlled. Control of rail-steel slags was recognized as one of the most important of many interdepending factors. The object of slag control is to hold the slag compositions within a range that gives the best results with respect to economy of production, uniformity of analysis, and quality of the finished rails. The most important component of the slag from the standpoint of these production and quality factors is the ferrous oxide content. This component is a good indicator of the basicity and oxidizing power of the slag, and these largely govern the effect of the slag on the steel. Consequently, the

Jan 1, 1935

By A. P. Miller, T. S. Washburn

Improved procedure in the manufacture of rail steel has come as the rail user demanded better wearing qualities combined with greater unit weight. With each weight increase per lineal yard has come greater difficulty in making a product that would successfully withstand all tests that modern rails must meet. With these facts in mind, and with a sincere desire to produce a rail whose service in track would be satisfactory in all respects, the steelmaker was quick to realize that all of the factors entering into his process would have to be more closely controlled. Control of rail-steel slags was recognized as one of the most important of many interdepending factors. The object of slag control is to hold the slag compositions within a range that gives the best results with respect to economy of production, uniformity of analysis, and quality of the finished rails. The most important component of the slag from the standpoint of these production and quality factors is the ferrous oxide content. This component is a good indicator of the basicity and oxidizing power of the slag, and these largely govern the effect of the slag on the steel. Consequently, the

Jan 1, 1935

By B. F. Tillson

ALTHOUGH most accidents occur through the A carelessness or misfortune of the workmen; that is no reason why we should not take all physical precautions practicable. The best way to approach the problem of mine safety is to acquire a personal feeling of responsibility for the accident and then plan how it might have been prevented had we known that it was to occur. A statistical analysis of the physical conditions contributory to accidents will give an indication of some of the methods or mechanisms that should be revised or safeguarded. The handling of rock or ore is a common source of minor injuries. Freedom from accident when mucking largely depends on the skill and care of the workman; this also is true, to a certain degree, to loading cars from chutes, but much can be done in the layout of chutes and their equipment to provide equal safety with less skill. Permanent stagings, or rigid units that may be easily assembled, should be provided so that the men handling the chute boards or gates and barring the jammed chunks will have a convenient safe footing for their operations. A stance to the side of the chute mouth is to one in front, because a man will not be liable to be struck by flying lumps or his bar, should it he caught in the mass, yet in many mines the workmen face the chute when loading a car. Fig. 1 shows the operation of a plank chute having special latches which support the chute boards in such manner that they may be conveniently dropped into place to stop the flow of ore.

Jan 1, 1926

By M. J. GAVEN

COMING over from the plant on the Denver and Rio Grande yesterday afternoon I was an interested listener to a smoking-room conversation that had to do with the experimental plant near Rifle. The people who were talking didn't know me and I didn't know them, but I learned quite a little. I understood that the plant would never operate; that it was not intended to operate; that the "oil trust" would keep it from operating; that our tramway had eaten up all our money and still was not working and would not work; that the plant was run by a bunch of kids, and that the superintendent was probably the biggest kid of the bunch. I plead guilty to the latter. But the people who were talking were misinformed. The plant is producing oil. The first sample of oil that came from our unit at the Bureau of Mines experimental plant at Rifle, Colo., was produced on Sept. 18, the first that came out of the condenser, and it is still coming. This sample of oil may mean to the United States what the first oil produced from the first well meant.

Jan 1, 1926

By H. W. Young

Development of high-tension outdoor substations during the past few years has been due primarily to economic reasons. The demand for power in small communities could not be met with the conventional and Fig. 1.—33,000-VOLT step-up outdoor air-break switch and substation installation outside of a powerhouse generating at 2300 volts stepping up to 33,000. Twenty-one coal mines are supplied from lines leading from this installation. comparatively expensive indoor types unless the rate for service was materially increased. To prove that the problems lncident to development have been solved successfully, it is only necessary to point to the wide adoption of outdoor substations by utility companies. Passing at once to the question as to whether outdoor substations are applicable to

Jan 1, 1920

By FREDERICK C. BROWN

THE practice of fine-grinding is now being so successfully - carried on in some fields, notably in West Australia, and its advisability has been so frequently pointed out' that the matter in this paper is not put forward as being new ; its chief object being to call attention to the importance of fine-grinding in the treatment of comparatively low-grade ores. I have been engaged during the last five years in the cyanide-treatment of ores in the Ohinemuri district (North Island), New Zealand, and I consider that, in the near future, extremely fine-grinding (almost sliming) will become a very important feature of the milling-methods in this field, since it seems absolutely necessary to reduce the most of ores to a very fine state of division if a high extraction is to be obtained; and, in most cases, the extra percentage of saving will leave a good margin above the increased cost of treatment due both to the fine-grinding and to the interest on the capital spent for the grinding-machinery. The average ore of the Ohinemuri field is composed of a quartz-gangue with some calcite, carrying the gold-value in the form of an alloy of gold and silver in about equal proportions, and the silver-value in the form of mixed sulphides of silver, usually associated with a considerable amount of iron pyrites. In the upper levels, the ores are decomposed and carry large quantities of black manganese oxide and some iron oxide, but, as. depth is reached, the decomposed ore gives place to sulphides and, in some mines, rhodonite, manganese silicate, is present in fairly large quantities. The average value of the

Jan 1, 1906

By R. E. Boni, G. Derge

Application of surface tension measurements has been made to molten silicates in order to determine the effect of sulphur upon the surface tensions of synthetic blast furnace slags. In melts with the same molar ratios of AI2O3 + SiO2 to the basic oxides BaO, CaO, and MgO, the surface tensions increase in the order of oxides listed. Sulphur lowers the surface tensions of the basic BaO, basic CaO, acid BaO, acid CaO, and acid MgO slags in that order; and the concentration of excess sulphur at the slag surface increases in this same order of slags. The rate and amount of desulphurization of iron by these slags is favored by a low excess surface sulphur in the slag. IN a previous paper,1 the authors discussed the applications of surface tension measurements of molten silicates to problems of metallurgical interest. Of major importance is the aid that such studies lend to forming a working concept of slag structure. Since the ability of a slag to desulphurize metal depends strongly upon its composition,2"4 fundamental information about the structural differences between various slags which contain sulphur should aid the development of better desulphurizing media. For that reason, the present investigation concerns the effect of sulphur upon the surface tensions of synthetic blast furnace slags. Experimental Procedure , The maximum bubble-pressure method was used to measure the surface tensions of synthetic blast furnace slags in the temperature range 1300° to 1600°C. The method is based upon the equation which was developed by Schrödinger5 from a consideration of the forces of hydrostatic pressure and surface tension of a liquid which oppose bubble formation when a gas is forced through a tube immersed in the liquid. where y is the surface tension between argon and slag in dynes per centimeter; g is the gravitational constant, centimeters per second2; H is the manometer reading in centimeters; s2 is the density of manometer fluid in grams per cubic centimeter; S1 is the density of the medium in grams per cubic

Jan 1, 1957

By William J. Robinson

What is the cumulative rate of recovery of copper from a sulfide leach dump? The technical answers to this frequently asked question may vary from "I don't know" to "quite good" from people of the same company. Management also poses this question because it plays a vital role in planning future production. The answer is difficult because of the many variables between different operations such as physical construction of the dump, topography of the original site, characteristics of dump material, mineralization, and water application. Each of these factors and others have a bearing on the rate of recovery. Anaconda's method of water distribution at Butte is unique in that each dump is drilled to allow physical injection of water into the dump. The injection holes are drilled vertically on 25-ft centers from the surface of the dump [(Figs. 1 and 2)]. Normally, the holes are drilled 40 ft deep and cased with 4-in. PVC perforated pipe. The pipe is perforated at 1-ft intervals with four 1 -in.-diam holes at 90° spacing on the pipe circumference. Formerly, shallow holes (20-40 ft) were alternated with deep holes (80-180 ft) in an effort to cover the entire dump and hasten oxidation. The shallow hole depth varied according to the compaction thickness. The deep hole depth varied according to the height of the dump and the original ground profile. It is preferable to have the deep holes end 20-30 ft above the original ground level. This generally allows penetration of the coarse material at the bottom of the dump. Deep holes had to be discontinued in order to cover more

Jan 1, 1974

By N. A. Gokcen, John Chipman

D. C. Hilty (Union Carbide and Carbon Research Laboratories, Niagara Falls, N. Y.)—This paper is a very nicely detailed analysis of a difficult problem. I would like to point out that the results that Mr. Crafts and I published a few years ago had no reference to activity, or anything else of a similar nature; our results were strictly empirical. It is quite gratifying that we now have a case where results involving activity coefficients and results derived from direct observations on actual steel melts are practically identical. When two different laboratories, working from two entirely different approaches, come out with results in such good agreement in their major significance, that is an achievement. It is something that was not possible 15 or 20 years ago. There is one question I would like to ask Dr. Chip-man. It has to do with a very minor point of disagreement in these results. When we reported the kink in the Si-O solubility curve I think you may recall that it came at the different temperature levels at about the order of 0.015 to 0.03 pct 0 and 0.03 to 0.07 pct Si—we also pointed out that we had difficulty in obtaining data at that level, although we finally did get some. I note in going through the data for the present paper, that there are no samples in those particular silicon and oxygen ranges. I wonder if that was purely accidental or was there a reason for it. D. E. Babcock (Republic Steel Corp., Youngstown, Ohio)—Mr. Hilty, do you have any explanation for that discrepancy between Dr. Chipman's curve and your own Mr. Hilty—Our explanation for it at that time was that for some reason our system probably was not in true equilibrium with SiO, that is, in equilibrium with the silica crucible at that level. We did observe, however, that that was the level at which both the metal and the slag became saturated with SiO,. On the average, in studying inclusion formation in small ingots permitted to solidify normally from the molten state, we observed pure silica inclusions at silicon contents over about 0.05 pct and FeO type inclusions at silicon

Jan 1, 1953

By R. A. Conkling

DORSET HAGER, Tulsa, Okla. Recently we have, been doing a little work along the same lines Mr. Conkling has outlined iii his paper. I am not prepared to say that Mr. Conkling is not correct but our results do not agree with his. I think it is a question of difference in correlation and interpretation of the well records. Our cross-section of the Cushing pool does not agree with that of Mr. Conkling and we find instead of the beds thickening in the syncline, there is a tendency to thicken on top of the anticline. We took the north dome of the Cushing field, and are now trying to get all the records. It will probably be another month before we have all the data complete but our results at present do o not agree with those of Mr. Conkling at all.

Jan 4, 1917

Jan 1, 1879

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) No. 544.-Mining engineer, 39 years of age, graduate E. M. with extensive experience in the United States, Canada and Spanish-speaking countries. Good organizer, energetic and resourceful. Experience covers mining and milling of gold, silver, lead, copper, zinc and tungsten. At present a Captain of Engineers, U. S. A., expecting to be released shortly. Open for engagement as manager, superintendent or examining engineer. Correspondence and personal interview solicited. No. 545.-Engineer and geologist, member, age 29 years, technical graduate and married. Six years' practical experience as surveyor, chief engineer and in exploration work in West, Southwest and Mexico. Speaks French and Spanish. Desires position with exploration company or as engineer and superintendent of small mine. Will be released from commission in United States Navy about February 1. No. 546.-For staff position-or manager. Member, married, graduate mining and metallurgical engineer, 18 years' experience in underground and metallurgical work on gold, silver, copper, lead and zinc ores. Details, references, and qualifications will be sent if requested, or may be seen at Institute office. Available immediately in United States or Canada. Would go reasonable distance for an interview if desired. No. 547.-Member, experienced in mine operating, engineering, general contracting and constructing. Technical graduate, mining engineer, married, age 38 years. Many years' practical experience while advancing through different positions to manager. Best of references and rating. Desires change. Position with future. Can obtain results. Salary commensurate with position. Available on short notice. No. 548.-Mining engineer, member, technical graduate, age 31, on military service since August, 1914, available after January 31. Best of references.

Jan 3, 1919

By E. B. BESSELIEVRE

THE great work of Gorgas in stamping out yellow fever in Panama during the construction of the Canal was one of the chief factors contributing to the ultimate accomplishment of the task, two previous attempts having failed largely through the demoralization of workers by epidemics of contagious diseases. Mining camps, rapidly constructed during the boom days of the rushes to new fields, have been frequent sufferers from typhoid when, as so often used to be the case, little or no attention was given to bacterial examination of the water supply or to the method used for disposing of the sewage.

Jan 1, 1930

By Frank Alfred Fahrenwald

A complete list of the elements as given for 1915 includes 18 that melt above 1,700" C. There does not exist one complete thermal equilibrium diagram for any pair of these 18 elements. Several of these elements have been combined, in relatively small proportions, with metals of lower melting point: e.g., tungsten, molybdenum, and vanadium, in steels, or with nickel and cobalt; but of this refractory group, platinum is the only one that has been extensively studied in this connection. When one considers that, with few exceptions, the industries have made use of alloys to the exclusion of pure metals, it is reasonable to expect that alloys of this refractory group will invade fields in which the pure metals have found little application. The past neglect of this class of metals has, no doubt, been partly due to the rarity of some of them, for even though alloys of very valuable properties should be developed, their cost, unless in exceptional applications, would be prohibitive. There is also a well-founded reluctance to undertake research involving very high temperatures which, in the case of most of these elements, must be accompanied by an inert atmosphere as well. This combination of high temperatures*and control of atmosphere within the heating chamber of any furnace of present design is a difficult problem. It is the purpose of this paper to give results,' of an investigation of one binary series of this group, in which methods were employed that avoided the usual difficulties accompanying high-temperature alloy investigation. , Historical.—The alloys of tungsten and molybdenum have received very little consideration during the past. A review of available literature reveals very little regarding this system, and that which has been recorded seems to be at fault. Mennicke2 writes, "Die bekannteste Verbindung

Jan 1, 1917

By E. Horton Jones

CONTENTS I Page Introduction ....:......................... 3 Chapter I. Unit Costs. . ...................... 4 Chapter II. Comparative Costs ..................... 20 Chapter III. Composite Costs..................... 32 Chapter IV. Wage Scale....................... 36 Chapter V. Raw Material Prices................. 37 Chapter VI. Description oF Costs ................... 64 Introduction We have endeavored in the following "sheets" to give the unit construction costs derived from 'the building of the Arizona Copper Co.'s new smelter, Clifton, Ariz., starting in February, 1912, and completing February, 1914.l In Chapter I—Unit Costs—are to be found the most elementary total unit costs which the accounts provide for. They are usable in the Clifton district. Here too are found the percentages to be added to an estimate for Engineering and General Expense. In Chapter II—Comparative Costs—these elementary costs have been classified, averaged and reported as labor and material unit costs. In such form the labor unit costs, when properly applied to similar conditions as these under which they were derived, are usable anywhere. The material unit costs are better disregarded for more accurate estimates and replaced by a newly priced bill of material. In Chapter III Composite Costs are given. They are unit costs built up from several elementary units, and likewise units of larger dimensions and simpler application, valuable for

Jan 1, 1915

By A. W. Hahn

USE of gold leaf goes back to biblical and even to prehistoric times. Both gold and silver, as well as other metals, were employed in illustrating or illuminating manuscripts. The medieval monks also used bronze powders. Metals were subdivided as finely as possible by mechanical methods, or by granulation and then were pounded into finely divided flakes. Substances such as honey have also been employed, since early times to keep the flakes of metal apart during grinding. Stearic acid is a more modern agent used in flaking aluminum and other metals. Finely divided "blue powder" is a by-product in retorting zinc ores, and contains from 78 to 90 per cent of zinc metal. This has been used as a precipitant for precious metals in the cyanide process and for chemical reduction processes. The making of zinc dust by atomizing is a step well known in electrolytic zinc plants. The Thermit process of Goldschmidt also requires the use of finely divided aluminum.

Jan 1, 1937

By E. C. Truesdale, Gerald Edmunds

A few years ago H. M. Cyr, working in the Research Laboratories of The New Jersey Zinc Co., produced a few pounds of zinc1 of such purity that no other elements were detected in it by spectrographic analysis, using the facilities then available. This zinc contained less than one ten-thousandth of one per cent of metallic impurities.&apos; During the decade that followed upon the laboratory production of this "spectro-graphically pure" zinc, commercial developments brought about the production of large tonnages of zinc of purity exceeding 99.99 per cent, and today zinc of 99.999 per cent purity is produced and marketed as "chemically pure" zinc. Typical analyses of present supplies of high-purity zinc are given in Table 1. Table 1.—Typical Analyses Percentnge by Weight Sum of Zinc Fe, Ib1 Fe Cd 1A1 cd Special High Grade*.......... 0.007b 0.005b 0.005b none O.OIOb C.P. (chemically pure)......... < 0.0002 0.0005c 0.000052 S.P. (spectrographically pure).. <0.0002d <0.00005d a A.S.T.M. Standard Specification for Special High Grade Slab Zinc (A.S.T.M. Designation: B 637). b Maximum. &apos; Fe chemically determined. Pb and Cd are spectrographically determined. d Differences between composition of C.P. and S.P. zinc are discussed later in this paper. The availability of commercial tonnages of special high-grade zinc has been the basis for the development of the zinc-base die-casting alloy industry which, in the year 1936, consumed one-eighth of the zinc used in the United States for all purposes. This and the C.P. and S.P. grades have given impetus to scientific investigations into the properties of pure

Jan 1, 1939