Search Documents

By W. A. Young

To initiate this project a critical evaluation of the pre-sent phosphate mining industry in the Western phosphate field was conducted. Mines were visited, mine operators were interviewed and pertinent literature studied. Three phosphate mining enterprises were reviewed and mining cost estimates prepared. The report discusses the present state of phosphate processing, rock alteration and location. New ideas and concepts are proposed to improve the recovery of phosphate rock from the Phosphoria formation. The report evaluates two variations to the present phosphate open pit mining methods, which were developed to improve the economics of mining phosphate and to better accomplish necessary reclamation and accelerate the time for environmental recovery. A material handling system using conveyor haulage will eliminate the need for trucks. Terrace haulback utilizes safety benches to haul and dispose of waste in the mined out pit. Ore will be removed from the pit via an inclined, cable-supported mobile conveyor.

Jan 1, 1980

Deep level block caving as a mining method is becoming more popular due to the fact that it is the lowest cost per ton underground extraction system. However, many block caves do not achieve their full potential due to draw horizon instability. In this paper five design rules are given to overcome this problem. The design rules described are applicable for slusher and trackless block caves where the operational depths exceed 500 metres.

Jan 1, 1999

By Vilma Beltrán

Dado que los trabajos de procesamiento metalúrgico de la mina Uchucchahua, ocasionaron impactos en el medio ambiente, afectando la calidad del agua y eliminando la vida acuática en las lagunas Añilcocha, Colquicocha y Tinquicocha, se procedió a encontrar una alternativa de tratamiento biológico que recupere la calidad de vida en la mina Uchucchacua. En este sentido, el presente trabajo describe el tratamiento pasivo de los efluentes con manganeso de la mina Uchucchacua. Para dicho procedimiento, se desarrollaron trabajos en dos etapas: el de laboratorio y balde. El primero comprende los sistemas de tratamiento pasivo anaeróbico y aeróbico.El aeróbico se inició sobre la base de los procesos de filtración y aireación a fin de determinar el grado de oxidación y precipitación del manganeso como óxido, mientras que el segundo se realizó en función a los resultados obtenidos en la etapa laboratorio y comprende los siguientes procesos: filtración, autooxidación, aireación, sedimentación. En consecuencia, los procesos anaeróbicos no favorecen la reducción de Mn II en los efluentes estudiados, mientras que los procesos aeróbicos permitieron la disminución del manganeso.

Sep 13, 2001

By Gordon R. Sima

This contract is concerned with the construction of a Time Resolved Audio Dosimeter System consisting of one readout unit and several dosimeter units. The Time Resolved Audio Dosimeter System was designed and developed by the Bureau of Mines with the purpose of this contract aimed at obtaining additional units for further field testing and evaluation. All construction was in accordance with the Bureau of Mines design and/or Bureau approved drawings produced during the course of this contract. This report contains a summary of the construction efforts, problems encountered, recommendations and all drawings produced under this contract.

Jan 1, 1977

By R. Dahlke, J. A. Finch

A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick mine concentrator to investigate the role of gas (air) superficial rate (Jg) distribution to the cells in the final Zn cleaning stage (bank of seven cells), i.e. the Jg profile. Three profiles were tested: “balanced” (each cell with same Jg), “increasing” (from cell 1 to 7 proportionally), and “decreasing,” along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was the response of the first cells in the bank where the increasing profile gave the highest selectivity of sphalerite against nonsulphide gangue (NSG). The other profiles gave lower selectivity and higher zinc recovery in the first cells, which combined to reduce overall bank performance. The higher selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG. The increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.

Jan 1, 2004

By H. W. Hunt

Accessories are increasingly used to protect and extend H, pipe, precast concrete, timber, and sheet piles for any soils conditions. With point protection, piles can be driven through boulders, layered rock, garbage dumps, and waterfront debris to provide dependable support for all types of structures. Splicers for pipe piles can be tapered for a water-tight drive-fit that does not require welding. The pipe splicer can be made applicable to precast concrete piles. Splicers for H make the long pile as strong as an unspliced length with only simple welding. Transition splicers quickly connect different types or sizes into efficient composite piles.

Jan 1, 2010

By Theodore L. Turner

This Bureau of Mines report describes calcination of kaolinitic clay in a direct-fired 2-1/2- by 24-ft rotary kiln at 750° and 775° C. Methods for preparing kaolin feed materials and characterization of calcined products are discussed. Approximately 99 pct of the alumina in a typical eastern Georgia kaolin was soluble in HC1 after calcination at either 750° or 775° C.

Jan 1, 1982

By John Meuth, Brandon Fryman, P. E. Hoffman, Joshua Ph. D., P. E. Calnan, Josh Ph. D.

Quantitative Risk Assessment (QRA) can be specifically tailored for use by the commercial explosives industry to calculate risk to employees and the public from commercial explosives facilities and operations. This methodology has several advantages over the American Table of Distances (ATD) which is solely a Quantity Distance (Q/D) analysis. While the ATD has remained essentially the same for 100 years, the safety of commercial explosives in storage has increased immensely. However, the concepts behind QRA calculations are not as intuitive and even at the end of the calculations the values of risk must be compared to something. A few regimes for assessing an acceptable level of risk are discussed in this paper. Risk levels for various United States Federal entities and international agencies are highlighted and suggestions for acceptable risk criteria for individuals and groups are provided. Referencing risk levels from normal daily activities is also done in this paper to make relative the accepted risk criteria. This paper presents some relevant individual risks for everyday activities and some scenarios for group risk for comparison. Individual risk is a straightforward concept however group risk is more complicated. This paper aims to clarify these concepts and provide means to communicate them to the public.

Jan 1, 2019

The material presented in this paper describes experimental work to determine the effect of variations in suction nozzle design upon inlet flow conditions. Four entrance profile shapes were examined under controlled conditions of slurry flow and it was found that the straight ended nozzles had consistently higher entrance losses than the straight taper or the ellipse, and that the circular arc profile nozzles were the most efficient. Subordinate considerations were the measurement of the quantities and the forces involved.As the work progressed, three distinct phases in the pattern of flow were apparent and the static pressures in each were carefully examined. An inlet zone was found to be unstable in changing boundary conditions, a transition zone was largely independent of slurry density and in a zone of stability the pressures were found to be directly related to the characteristics of the flowing pulp. In this zone pressure measurements were reproducible within ± 2 per cent regardless of changing boundary conditions.The effect of varying the "1" parameter of nozzles with a part circular entrance profile was examined and it was found that flow conditions approaching the ideal were obtained when the radius of curvature was between 0·40 and 0·550.

Jan 1, 1966

Two outstanding features of the world's young orogenic belts are their very consistently developed suites of volcanic rocks and, it is now recognized, the rather distinctive types of mineralization they contain. Further,it is now known that these volcanic suites exhibit evolutionary patterns, and it is beginning to appear that this evolution in style of igneous activity is accompanied by a parallel evolution in style of mineralization. Specifically,podiform chromite and stratiform pyritic copper ores of Alpine ultramafic/submarine tholeiite association progressively give way to more zincian stratiform ores associated with andesites and dacites, "porphyry copper"deposits developed in quartz dioritic to dacitic plugs, and lead-zinc stratiform ores related to increasingly pyroclastic, rbyodacitic volcanism.This "coupling" is exhibited well in the volcanic arcs - the young orogenic zones-of the SW Pacific which, with tbeir abundance of youthful and commonly unmetamorphosed materials provide an opportunity for investigating, through a petrochemical approach, the possible significance of ores in the elucidation of mechanisms of lava formation. It is suggested as a working hypothesis that in the orogenic (voleanic arc) regime ores are associated with the cale-alkaline rocks because these cale-alkaline rocks are in part generated by exhalative loss, and the ores are among the manifestations of tbat loss.

Jan 1, 1978

By R. B. Rao, B. Das, J. K. Mohanty, D. S. Rao

Physical, mineralogical and geochemical characterization, along with some beneficiation approach to pre-concentrate the Ni content of the chromite overburden material of the Sukinda Valley, India, have been carried out in detail. Mineralogically, the overburden consists of geothite, quartz, hematite, magnetite and secondary silicates in varying proportions. A specific Ni mineral phase is absent in this material with the Ni and Fe being mostly enriched in finer fractions. Distribution of Ni and Fe in various size fractions and increase of Ni with increase in Fe (goethite content) indicate that goethite is the major Ni-bearing mineral phase. Quantitative estimation of goethite from chemical analysis and weight loss data indicates that the goethite quantity varies from 40% to 90%. Electron microprobe analysis (EPMA) indicates that Nirich and Ni-poor goethite are present in the overburden material. A sequential dissolution study indicates that more than 50% of the Ni are present within the goethite lattice as a lattice substitution. The results of pre-concentration studies (size classification, gravity, flotation and magnetic separation) indicate that Ni is richer in finer fractions. Further, the enrichment of Ni content is limited to 1.1% with 50% recovery by classification followed by hydrocyclone separation of the below 53 m m fraction.

Jan 1, 2000

By Nick D. Rose

The importance of structural geology in open pit slope stability is overlooked in many mining operations due to pressures to cut costs and minimize mine personnel. As a result, mine geology staff are often unable to keep up with geological mapping of the pit slopes due to other day to day production oriented tasks. In some instances, key structural controls that contribute to slope instability may not be identified until after a slope instability has initiated, at which time it may be difficult or impossible to delineate these features in the field. Even for small slopes, understanding the engineering and structural geology of the rock mass, as well as the effects of groundwater and blasting practices, are of key importance to slope stability. Two case histories are presented as examples of mining operations that experienced slope instability with little more than anecdotal information about the structural and groundwater conditions encountered during mining. By conducting field reconnaissance, simple slope stability analyses and ongoing slope monitoring, practical remedial measures were implemented, allowing continued safe mining operation.

May 1, 2002

By French D

In presenting this paper may I preface my remarks by recognizing the presence here to-day of the many delegates from the overseas mining communities throughout the world. That is to say - those delegates not representative of Companies resident in Australia. This does not mean that my comments following are directed solely to the Australian exporter - far from it. The Company which I represent is internationally based. The experiences we have had in dealing and negotiating with our good friends the mineral cargo shippers vary very little in any operational area. However for the purposes of this exercise this address is based on some of our experiences within the Australian trade scene with the emphasis on the fact that we believe it has application to all trading areas.

Jan 1, 1989

By Gabriel S. Esterhuizen

This paper addresses the need for a method to compare the effectiveness of different support systems when designing ground support in coal mines. At present, support design methods include empirical methods based on observations of past performance of installed support systems, analytical methods where the roof is typically simulated by elastic beams and numerical model analysis. The approach presented in this paper estimates the relative stability of a support design through geotechnical evaluation of the rock mass and numerical model analysis of the interaction between the rock mass and the support system. Models are used first to simulate the design performance at the expected rock conditions. The rock strength is then reduced until collapse is indicated in the model. The stability factor is then calculated as the ratio of the expected rock mass strength to the rock mass strength at the onset of collapse, and is similar to the well-known factor of safety used in engineering practice. The stability factor can be used to assist in developing a final support design by comparing the effectiveness of various support systems and the stability of excavations under various geological and loading conditions. Examples of the method?s application in three different geological settings are presented.

Jan 1, 2012

By James W. Marold

Tunnel and shaft plugs have been designed to assist in construction of new and rehabilitation of existing tunnels and shafts. Tunnel plugs have been used to provide construction access for side by side tunnels, separation of raw and treated water, and to allow operation of one tunnel during construction of a nearby tunnel. Shaft plugs have been used to seal up surface openings to tunnels and to prevent seepage of water to the surface through adjacent tunnels or shafts. The design construction details of tunnel and shaft plugs are provided. Typical examples of tunnel and shaft plugs are provided.

Jan 1, 2008

By Flavio Rojos-Tapia, Samuel Sánchez-Pino, Marcelo Fernández-García, Samuel Sánchez-Baquedano, Rainer M. Imhof

"Pneumatic flotation was introduced to the Chilean copper mining industry in 1993 by Ingeniería de Minerales S.A., being implementation in 1994/95. The technology is based on the designs and development of Dr. Rainer Imhof from Germany and from Chilean copper processing experience.Pneumatic flotation has been successfully used for sulphide and oxide copper minerals and copper slag, iron ores (reverse flotation), gold and promising results with molybdenum as product. Extremely hard conditions were applied in flotation process such as roughing, cleaning, scavenging. Pneumatic flotation can be applied for any type of mineral which has to be separated by flotation. Even very dense and heavy slurries can be processed, the range of the particle sizes to be collected is very wide, and the number of cleaning stages needed normally is one in our experience until now.The good performance of the technique can be explained by the high gas hold-up and the very effective micro-turbulences which boosts the attachment to the bubbles changing dramatically the flotation time concept. Some economic high lights are: less energy consumption, less maintenance costs, simple and reliable to operate and it is required a small area to install the circuits.As a result of the Chilean mining industry experience, it can be concluded that the pneumatic flotation can be regarded as an excellent alternative to the conventional way of Mineral Processing.INTRODUCTIONDerived from seventies, works in Germany about pneumatic flotation with Prof. Simonis (Technical University of Berlin) and Prof. Bahr (Technical University of Clausthal), it has been developed an interesting flotation technology in Mineral Processing, with the designs developed by Dr. Rainer Imhof, who has been known for more than ten years (Imhof, 1998) by his contribution at Ekof, KHD, Allmineral and the actual company Maelgwyn Mineral Services where he is a Technical Director. Ingeniería de Minerales S.A. has been working ten years deeply involved with the technology developed by Dr. Imhof and is more than ten years experienced with pneumatic flotation, from Wits University and Mintek in South Africa (Sánchez, 1990), (Sánchez, 1990)."

Jan 1, 2003

By Mingju Liu

China has been suffering from coal and gas outbursts since 1950s. Nowadays, the situation has become worse than ever with the need to mine deeper coal deposits at higher production rates in a more complex underground mining environment. In the year 2006 alone, 37 outbursts occurred in underground coal mines with a death toll of 232. This paper describes a case study of an outburst event, which occurred in July 2006 during the shaft development of the Mengjin Coal Mine, Henan Province, China at a depth of 768m below surface. Detailed analysis of the possible causes that led to the occurrence of the outburst is reported. These include the study of complex geological features, gas storage conditions, possible improper technical management practice as well as incomplete prevention and control measures. Based on the case study and the observation of outburst occurrence in China in the year 2007, suggestions have been put forward to help prevent and control future coal and gas outbursts.

Jan 1, 2007

By Taegong Ryu

Nanosized tungsten powder was synthesized by the hydrogen reduction of ammonium paratungstate (APT) in thermal plasma. The effects of operating conditions on the product composition and particle size were investigated. The particle size of synthesized W powder was less than 30 nm in all cases tested. The sintering behavior of the synthesized powder (25 nm average size) was then investigated and compared with those of commercial W powder of 500 nm average size and W powder of 23 nm average size produced by milling the commercial powder. The sintering was done at 1400oC with various holding times. The hardness of the resulting compact from the synthesized W powder (315 VHN) was similar to that from the milled W powder (309 VHN), but the plasma-synthesized powder had a much lower tendency to form cracks. The compacts of both nanopowders were significantly harder than that of the commercial powder (192 VHN).

Jan 1, 2009

By Jim Baumann

Deposited millions of years ago in irregular paleokarstic channels, Jamaica’s extensive bauxite deposits provide good quality ore for alumina production and subsequent aluminum smelting. Bauxite mining operations are critical to the Jamaican economy. It accounts for a large percentage of Jamaica’s export earnings. Bauxite production in Jamaica accounts for about 10% of the world’s output each year. Bauxite deposits in Jamaica lie close to the surface. They can be extracted using standard surface mining techniques. The deposits occur in scattered pockets across the country’s rugged landscape. So it was necessary for two of the country’s major mining and refining operations to implement cost effective methods for the acquisition and management of bauxite reserves and surface ownership distribution rights.

Jan 1, 2002

By S. Jennings

The Red Dog zinc-lead-silver deposit is located in the DeLong Mountains of the western Brooks Range in northwest Alaska. The region is located 145 km(90 miles) north of the village of Kotzebue (Fig. 1).Red Dog’s current resource base is 143 Mt (157 million st) averaging 16.1% zinc, 4.3% lead and 83g/t (2.4 oz/st) silver. It is contained in four structurally separate deposits— the Hilltop, Main Deposit, Aqqaluk and the newly discovered Paalaaq deposit. Recent exploration for the Aqqaluk and the Paalaaq deposits has contributed to Cominco American’s understanding of the detailed structural geology of the district and its role in the placement of individual ore bodies.

Jan 1, 1999