Search Documents

By E. F. Johnson, V. O. Naumann, D. P. Bossler

A method is presented for calculating individual gas and oil or water and oil relative permeabilities from data obtained during a gas drive or a waterflood experiment performed on a linear porous body. The method has been tested and found both rapid and reliable for normal-sized core samples. INTRODUCTION Individual oil and gas or oil and water relative permeabilities are required for a number of reservoir engineering applications. Chief among these is the evaluation of oil displacement under conditions where gravitational effects are significant, such as a water drive or crestal gas injection in a steeply dipping oil reservoir. Numerous proposed methods of obtaining relative permeability data on reservoir core samples have been too tedious and time consuming for practical use, or have yielded questionable and sometimes inconsistent results. A method has been developed by which the individual relative permeability curves can be calculated from data collected during a displacement test. The method is based on sound theoretical considerations. Using this method, with a properly designed experimental procedure, relative permeability curves can be obtained using core samples of normal size (i.e., 2 to 3 in. in length and 1 to 2 in. in diameter) within a few days after receipt of the core. In a recent publication D. A. Efros1 describes an approach to the calculation of individual relative permeabilities that is based on the same theoretical considerations. We believe the approach described in the present paper is more adaptable to practical application than the method implied by Efros. In addition, comparisons with independently determined relative permeabilities are furnished to substantiate the reliability of the new method. DERIVATION Previously the theory of Buckley and Leverett as extended by Welge2 as been used to calculate the ratio of relative permeabilities. In the derivation which follows, this theory is further extended to permit calculation of the individual relative permeabilities. The theory assumes two conditions which must be achieved before the method is applicable. They are that the flow velocity be high enough to achieve what has been termed stabilized displacement,3 and that the flow velocity is constant at all cross sections of the linear porous body. In stabilized displacement the flowing pressure gradient is high compared with the capillary pressure difference between the flowing phases. The high pressure drop insures that the portion of the core in which capillary effects predominate will be compressed to a negligibly small fraction of the total pore space. The assumption of constant flow velocity at all

By P. Pyykkö, E. Peuraniemi, J. Järvi, P. V. Latostenmaa, V. Törölä, S. Junnikkala

"Nickel concentrate smelting started in Harjavalta in 1959. First, flash smelting - Peirce-Smith converting route was applied, and the high-grade converter matte was further refined to nickel cathodes. In 1995 the original smelter flow sheet was simplified with the novel DON (Direct Outokumpu Nickel) technology. In Harjavalta with the DON technology, high-grade nickel matte with low iron content is produced in flash smelting furnace directly without subsequent converting stage. The metal values in the smelting slag are recovered in an electric furnace as an iron containing bottom alloy. Main special features in Boliden Harjavalta nickel smelter are smelting of high-magnesia concentrates, the high recoveries of nickel and copper, as well as those of PGM`s and cobalt.Sulfur and dust emissions to air can be seen generally as one main disadvantage of nickel smelting operations. In Harjavalta continuous improvements in environmental performance has been rewarded by minimum sulfur and dust emissions to the environment and working atmosphere. Today Boliden Harjavalta’s nickel smelter is presenting state-of-art-technology at nickel smelting.This paper describes the nickel smelter process and includes recent production and emission data. It describes features required to achieve environmental and occupational hygiene goals and compares environmental performance data to that published on other smelting operations. General description of New Boliden Way is presented and a case example of production stability project is also presented."

Jan 1, 2014

By W. L. Swager

Tramp (undesirable) elements introduced into iron and steel castings via purchased ferrous scrap are evaluated as to their likely degree of future threat to the quality of castings. Conclusions are based on analysis of literature and on nonmail surveys of foundries, scrap processors, trade and technical associations, and others. The existing tramp-element problem is expected to be persistent, but amenable to improved control by foundries and their suppliers. Four recommendations for action are given.

Jan 1, 1981

By Art Cooper

Granulation systems are customarily viewed as problem areas in metallurgical operations. The inherent risk of explosion when combining a high temperature melt with water creates a safety hazard. Separation of the granulated material from the quenching medium generally involves equipment that can have significant maintenance and operating costs. Granulation systems' reliability and availability can negatively affect the plant production. Against this background, granulation systems have been treated by design firms and producers as an add-on and a necessary evil. The technology is becoming better understood and solutions to common problems are being found. This paper will discuss typical problems in common systems, and some of the improvements that have been made, with particular reference to non-ferrous applications.

Jan 1, 2006

The 2003 SME Annual Meeting and Exhibit will take place Feb. 24-26 in Cincinnati, OH. The meeting will feature a host of special symposia and programming geared toward the industrial minerals and aggregate industry sectors. This programming focus is particularly relevant for this annual meeting, as it will be hosted in the center of America’s transportation hub and industrial mineral center. Cincinnati, located on the Ohio River, is key to the movement of America’s supplies and construction material needs.

Jan 1, 2003

By Garry Biles

The Eskay Creek Mine is a high-grade gold and silver underground mine in northwestern British Columbia. The mine started operations in late1994. For the first three years, ore was crushed to -50 mm(-2 in.), blended to satisfy smelter terms and shipped to smelters in Japan and Canada. Preliminary evaluations indicated that a complex metallurgical facility, requiring a large capital investment, would be required to recover the precious and other economic metals. So markets for raw ore were identified and underground mining and ore transportation operations began at a production rate of 300 t/d (330stpd).

Jan 1, 2000

By Michael Amick

Over the last few years as the coal industry has seen an increase in the price of coal, a renewed interest in the additional mining of pre-law highwall sites has occurred. Much premium coal and property remains behind these pre-law highwalls but access to mining is limited because prior mining used auger machines to remove coal from under the highwall. Older augers seldom reached more than 200 feet and often no more than 100 feet but this zone of auger holes destabilizes the highwall to where additional mining is often unsafe. If the reserve is large enough, the highwall can be stabilized with common flyash and cement grouts to form a face-up for an underground mine but this expensive method is usually not practical for continuous use with a highwall mining machine. It is estimated there are hundreds of miles of highwall riddled with auger holes where the coal reserve available is ill-suited for deep mining for a variety of reasons. However, these same properties are ideal for additional mining with state-of-the-art highwall mining machines that have a reach up to 1200 feet, except to the relatively thin auger mined de-stabilized zone. The renewed interest in highwall mining these properties has driven research into finding an economical way to stabilize the highwall so the highwall mining machine can recover additional coal. This research discovered and fine-tuned a process that is economical and is successfully supporting the highwall at a highwall mining operation. This paper discusses the research involved in determining the strengths need, the methodology used to place any grouts, the effect on mining plans and the increased recoveries. ARMPS-HWM is used extensively in this research. The failure of the highwall, when not grouting, and the success, when grouting using the new materials and equipment utilized, confirmed the ARMPS-HWM method.

Jan 1, 2007

By S. Cotten

The regulations for current coal mine refuge alternative (RAs) require that there be sufficient life support to sustain survival of the maximum number of RA occupants for a minimum of 96 hours. This minimum duration assumes that rescuers can access the RA through the mine within four (4) days of the onset of the mine emergency. But what if mine rescue teams cannot reach the miners within the RA before the RA air supply is severely limited or exhausted? What could be done to extend the duration of the RA life support capability into the 97th hour and beyond? In addition, what might be done to enable more rapid rescue of the miners if they could not be reached through the mine in a timely manner? This paper describes a systems approach to address the potential need to extend the duration of RA life support beyond current design limits. New capabilities that need to be developed in advance of such a dire need include more reliable emergency communications, highly mobile and efficient drilling rigs, enhanced directional drilling techniques, and a standardized RA external life support interface along with RA internal design modifications to accommodate use of an external supply. The following sections describe the need, intent, and technology gaps associated with each of these capabilities. Government agencies and the mining industry should consider initiation of a program to investigate, design, and develop effective means of extending the current 96-hour time restriction on coal mine refuge alternative life support. The development process should begin with a focused study to refine the overall operational concept, investigate the current state-of-the art of critical technologies, identify specific technology development priorities, and make recommendations for a development program to provide in an organized, efficient, and timely manner a solution for extended refuge alternative life support and occupant rescue.

Jan 1, 2011

By Woodcock J. T

A sulphide ion selective electrode (ISE) is suitable for control of sodium sulphide additions in flotation because it has a rapid response to changeS in S2- concentrations, can indicate -low concentrations at differentpH values, suffers from few interferences, and is robust enou'gh to use in a pulp. Three sulphidization techniques were studied using the lSE electrode for measurement and/or control of S2- levels. Metallurgy was assessedfrom concentrate grades and copper recovery.With slug additions of sodium sulphide, sulphidizing conditions were poorly defined and reproducibility tended to be poor. Although acceptable metallurgy could be achieved by multiple additions, sodium sulphide consumption was high.Controlled potential sulphidization readily gave good metallurgy. The optimum potential of the lSE for sulphidizing was about -500 mV versus SCE, but depended on sulphidization and flotation times; suitable times were3 and 5 min respectively for three to five stages. Application of this technique to previously untested ores gave good metallurgy in a first test in spite of variation by a factor of three in the sodium sulphide requirements ofthe ores.Simultaneous sulphidization and flotation was satisfactory when conducted at an lSE potential of -450 mV versus SCE. Mixed cha!copyrite-oxide copper ores responded satisfactorily.Besides optimizing sulphidization conditions it is also necessary to optimize xanthate additions (e.g. by measuring xanthate residuals).

Jan 1, 1978

By Tad S. Golosinski

The paper describes Online Master of Engineering Program at the University of Missouri-Rolla and discusses the experience gained during the first three years of its offering. This innovative educational program is designed primarily for mature students with an engineering or science background who want to acquire or upgrade their knowledge of mining engineering. Students can specialize in several different areas of mining, such as surface mining, underground mining, mine environment and the like. All courses constituting the program are taken online, through the Internet, without the need to attend the UMR campus in person.

May 1, 2004

By P. Wearden, K. Bryner, K. Vrana, V. Castranova, R. Dey, R. Reist, J. Blackford

"Summary: Fibroblast proliferation and enhancement of collagen synthesis are key steps in the development and progression of pulmonary fibrosis. The current investigation presents a fibroblast proliferation assay to detect the release of competence factors from pneumocytes. The specific objective of this study was to define cell culture conditions for fibroblasts that would allow selective detection of competence factors in test media. The results indicate the following: (a) fibroblasts should be cultured for 2 days in plasma-free medium rather than 2% plasma to assure complete quiescence; (b) 1% plasma was optimum for producing progression activity for the bioassay of a competence factor, while 0.5% plasma did not produce sufficient progression activity (yielding false negatives) and 2% plasma often contained significant competence activity (yielding false positives); and (c) fresh plasma should be used since the progression activity of plasma was adversely affected by freezing and thawing. Under these conditions, this bioassay can be employed with either rat or human lung fibroblasts to detect competence factors such as platelet-derived growth factor (PDGF), at levels as low as 25 ng/ml.Fibrotic lung disease, as a consequence of occupational exposure to silica dust. is characterized by the development of concentric hyalinized nodular lesions in the lung and the progressive loss of pulmonary diffusion capacity. Proliferation of pulmonary fibroblasts and enhanced synthesis of collagen by these pneumocytes have been shown to be key steps in the development of chronic silicosis ( 1 ). The regulation of lung fibroblast proliferation by cytokines released from alveolar macrophages may be an important pathogenetic mechanism in the development of the fibrotic process (2). Some cytokines stimulate fibroblast proliferation by activating specific phases of the cell cycle (3,4). In particular, platelet-derived growth factor (PDGF) promotes fibroblast proliferation by inducing the movement of quiescent (G0 ) cells into the G1 phase of the cell cycle (5). Insulin-like growth factor (IGF) and transforming growth factor-P (TGF-P). on the other hand, regulate the rate of transition of fibroblasts from G 1 into the S phase (5,6). These two classes of cytokines have been termed competence and progression factors, respectively. One approach used to examine the release of cytokines from macrophages is the fibroblast proliferation assay in which quiescent fibroblasts are exposed to culture supematants from macrophages exposed to various stimuli. In most of these assays, the supernatant contains fetal calf serum (FCS), which provides the competence factor(s) necessary to facilitate the proliferation of fibroblasts (7-9). Recently, a fibroblast proliferation assay using platelet-poor .plasma [lacking competence factor(s)] as a substitute for FCS bas been described (I 0, 11 ). In this assay, the release of a competence-inducing PDGF-like growth factor from rat and human macrophages can be distinguished from other cytokines that act as progression factors."

Mar 1, 1992

The 108th Annual General Meeting of The South African Institute of Mining and Metallurgy was held at The Country Club, Johannesburg, Napier Road, Auckland Park on Thursday, 11 August, 2005. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations, also to recipients of awards, senior members of industry, Honorary Life Fellows, past-presidents, our members and other guests, among them the following: Dr Con Fauconnier, President, Chamber of Mines of South Africa Prof. Jay Barton, President, The Geological Society of South Africa V. Townshend, President, Institute of Certificated Mechanical and Electric Engineering, South Africa M. Livingstone-Blevins, President, Institute of Certificated Mechanical and Electrical Engineers, South Africa Prof. B. Lacquet, President, South African Institute of Electrical Engineers Dr F. Malan, President, South African National Institute of Rock Engineering

Jan 1, 2005

Pese a tener cajas sólidas en su estructura, algunas vetas desarrollan un relleno frágil, ocasionando problemas futuros de sostenimiento para el "corte y relleno" de los mismos. Por ello, se utilizó el método de los "Square Sets", donde además de ser costoso, implicaba eliminar una proporción de la roca encajonante y diluía el contenido metálico de los filones. En ese sentido, el objetivo del texto es señalar la viabilidad del "método Cornish"como método alternativo, económico, de rendimiento óptimo y que no presenta riesgos para el personal o la labor realizada. Este método es aplicable en aquellas vetas uniformes no falladas, que tengan desde una potencia pequeña hasta aquella que sea posible apuntalar, así como en aquellas que requieran sostenimiento del techo en la veta mima o donde se realizen Shrinkages. El proceso del método se basa en la preparación de los tajeos, luego en la explotación(perforación y disparos), enmaderado, relleno del tajeo, recuperación de madera, las variantes en la preparación del tajeo y la recuperación del mineral. La única desventaja que ofrece este método es su peligrosidad, dado que si se aplica en zonas inadecuadas o sin la supervisión que garantice el cumplimiento de las normas preventivas, es preferible el uso de los "Square Sets". Sin embargo, la aplicación del método resulta mucho más productiva en rendimiento teórico puesto que alcanza de 7 a 10 toneladas por tarea de 8 horas y responde satisfactoriamente siempre y cuando las condiciones de las vetas lo permita.

Jul 20, 1957

By Creelman C. A

The removal of a horizontal piIlar between Nos. 9 and 11 levels (1,116 feet from the collar of main shaft) was successfully carried out by blast hole drilling, and, to the best of the authors' knowledge, this mass blast of 40,000 tons of ore (requiring the use of 7,150 Ibs. of explosive and 5,385 feet of primacord) was the first occasion on which a task of this magnitude has been carried out underground in an Australian mine.Blast hole drilling was introduced by this company approximately fifteen months ago at New Cobar Mine in sub-level stoping.This experimental drilling and blasting gave very valuable information as to the correct technique to be adopted when the final plans were being prepared for the removal of the horizontal pillar at New Occidental Mine.The dimensions of this pillar were approximately 15 feet long, and from 40 to 60 feet wide, and 65 feet in depth.The block of ore extended to 35 feet above the level and 30 feet below, the upper section being partially excavated to form the bell-hole floor and grizzly chambers used for drawing off the broken ore in the shrink stope above the No. 10 level.Description of Ore-bodyThe main ore-body is situated almost vertically in a well-defined shear zone at the junction of sandstone and slate, the sandstone forming the eastern and the slate the western wall.The ore-body consists of highly silicified slate (chert) sparsely impregnated with sulphides, containing a small percentage of copper and bismuth.The total length of the ore-body is approximately 450 feet, with a maximum width of 60 feet in the main section, which is about 200 feet long.This is the section shown in longitudinal and cross-section (Fig. 1).The ore-body is divided by a horse of mullock in the northern end into two legs, the eastern and western, which are approximately 250 feet long and averaging 25 feet in width.This ore-body is strong, hard and abrasive with extremely strong walls, an ideal proposition for open stoping and mass blasting.MiningIn all levels above No. 9 the cut and fill method of ore extraction was adopted. On Nos. 10 and 11 levels the shrinkage method was introduced with economical results, and no difficulty had ever been experienced with shabby or bad walls.Shrink stoping had been carried upwards from No. 11 level to within 10 feet of No. 10 level, when mining hazards developed, and instead of...

Jan 1, 1944

By Fengyu Ren, Ruslan Puscasu, Kunpeng Yu, Gideon Chitombo, Liangliang Kang

Weak rock mass and poor flow of material can cause excessive ore loss and dilution in sublevel caving. This paper proposes a method to establish design parameters for an inclined deposit within a weak rock mass and evaluates its effectiveness through a case study. In order to solve the problem of low production capacity and poor safety conditions of sublevel caving mining at the Yingfangzi silver mine in China and to ensure a smooth production from the refractory ore body, it is necessary to select appropriate stope structure parameters. Based on random medium theory of gravity flow and the improved equation of ore discharge in random medium, an end wall drawing experiment is carried out to determine the optimum design and flow parameters. It was observed from the experiment that, due to the influence of the randomness of particle movement, there is a mismatch in the flow parameter measurement. The flow characteristics and distribution of the marker particles are different from that of the tested particles resulting in large drawbody shape distortion. The study finds that the flow parameters obtained by the new method are more practical and account for drawpoint width and recommends that the new method for determining the sublevel stope height is used when the drawbody is a non-standard ellipsoid. The outcomes have shown a significant reduction in the dilution and improvement in the recovery rates, and the safety and efficiency of mining have been greatly improved.

The 106th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the J.C. Lemmer Auditorium, SA National Museum of Military History, 22 Erlswold Way, Saxonwold, Johannesburg on Wednesday, 13th August, 2003. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations, also to recipients of awards, senior members of industry, Honorary Life Fellows, Past-presidents, our Members and other guests, among them the following: Kevin Moxham, President, Association of Mine Resident Engineers Prof. Jay Barton, Vice President, The Geological Society of South Africa Dr Gus Muller, President, Institute of Certificated Mechanical and Electrical Engineers, South Africa Marius van Rooyen, President, Institute of Mine Surveyors of South Africa Benjamin Ngulube, Deputy Vice President, South African Institution of Electrical Engineers Dr Francois Malan, Chairman, South African Institute of Rock Engineering Dr Paul Jourdan, President, Mintek

Jan 1, 2003

By A. J. Williams

"Conventional base metal milling practice normally consists of crushing, grinding and cyclone classification followed by flotation. It is the authors' belief that the commencement of flotation after cyclone classification leads to inferior metallurgical results and that implementation of flotation of grinding mill discharges can result in increased recovery due to reduced overgrinding, reduced activation of contaminating minerals and improved dewatering circuit results due to the production of coarser concentrates.The concept of recovering minerals from the discharge of grinding mills is not new! Gold concentrators have utilized jigs and flotation cells while iron ore plants have employed magnetic separators to recover gold and magnetite respectively from the discharge of grinding mills. More recently, a Reichert cone has been used to recover sulphide and oxide base metal minerals from screened rod mill discharge. 1To the authors' knowledge, the first application of flotation of base metal minerals from the discharge of a production plant grinding mill was at the Lake Dufault concentrator of Corpor'1tion Falcon bridge Copper. Located 10 miles north of Noranda, Quebec the Lake Dufault concentrator commenced operations in August, 1964.The installation of flot11tion cells in the Lake Dufault grinding circuit proved so successful that an identical system was installed in the Manibridge concentrator of Falconbridge Nickel Mines Limited. Located 90 miles southwest of Thompson, Manitoba the Mamibridge concentrator commenced operations in June, 1971 and due to exhaustion of economic ore reserves discontinued production in May 1977."

Jan 1, 1984

By James P. Ulery

In This Chapter [Geologic features associated with anomalous methane emissions Gas outbursts and blowers Methane drainage strategies for mitigating anomalous methane emissions and General considerations for a methane drainage program] This chapter summarizes how certain geologic features may be associated with unexpected increases in gas emissions during coal mining. These unexpected emissions have the potential to create explosive conditions in the underground workplace. Also discussed are the generally used practices to alleviate potential hazards caused by gas emissions associated with these geologic features. INTRODUCTION Unforeseen mine gas emissions in quantities sufficient to create hazardous conditions have been attributed to sources outside the mined coalbed since the first documentation of methane explosions in coal mines [Payman and Statham 1930]. Geologic features such as faults have long been recognized as conduits for gas flow from strata adjacent to mined coalbeds [Moss 1927; Payman and Statham 1930]. Other features such as sandstone paleochannels, clay veins, and localized folding have also been recognized for their impact on gas emissions into mine work-ings [Darton 1915; Price and Headlee 1943; McCulloch et al. 1975; Ulery and Molinda 1984]. The fact that strata adjacent to mined coalbeds can emit large quantities of methane gas into mine workings is not surprising from a theoretical perspective. Many researchers have recognized that during the burial and diagenesis of the organic matter forming today’s minable coalbeds, similar dispersed organic matter in adjacent strata has produced methane in quantities far exceeding the storage capacity of the coal and surrounding rock [Juntgen and Klein 1975]. It is not surprising then that large quantities of methane can remain trapped in these strata. A potential hazard occurs when mining of a nearby coalbed causes pressure differentials and mining-induced fractures conducive to gas flow into the mine workings from these strata. This gas flow may be facilitated or temporarily impeded by the presence of geologic structures or anomalies.

Jan 6, 2006

By G. E. Blight

Wind erosion can be a major cause of the loss and dispersion of tailings material from a tailings dam into its surrounding environment. Such dust dispersion can be a serious nuisance, as well as a health hazard to inhabitants in nearby settlements, and can also damage the health of animals, degrade crops, making them less marketable, and cause soil and water pollution. The problem of wind erosion can affect tailings dams in all types of climate, but becomes worse as climatic aridity increases. Because clouds of dust are often observed billowing across the top surfaces of tailings dams in dry windy weather, there is a common misconception that the dust arises from wind erosion of the top surface. As a result, much effort and money is vainly spent on treating the tops of tailings dams to prevent dust generation, whereas the slopes of the dams are the true major dust source. This paper briefly reviews what is known of erosion of tailings dams and then proceeds to describe the mechanics of wind erosion in general, and how it affects tailings dams in particular. Finally, recommendations are made for mitigating wind erosion of tailings dams and the resulting blowing dust.

Jan 1, 2007

By G. I. McPhail

The authors have conducted several investigations into the prediction of the beach profile of high-density tailings and have found that there are a number of important considerations that need to be taken into account over and above the reliability of the beach profile prediction methodology. These considerations relate to the chemistry of the slurry and specifically the influence of pH and flocculation, both of which have a significant influence on the rheology of the slurry at the discharge point. A number of examples are discussed and a potential testing protocol that will assist in assessing the influence of chemistry ahead of the beach profile predictions is presented. A methodology for assimilating the results of the testing into the likely field situation is discussed, and suggestions are made on application of the results in beach profile prediction. The suspected influence of residual flocculation on the stratification

Jan 1, 2012