Search Documents

By Koch D. F A

An electrochemical study of the dissolution of gold in aerated cyanide solution shows that the dissolution rate is determined by the nature of the surface. A passive film (probably a basic cyanide) formed at -0·6 V vs a saturated calomel electrode inhibits both the anodic dissolution of gold and the cathodic reduction of oxygen. Thallium has an "activating" effect on these reaction mechanisms.INTRODUCTIONIn general the dissolution rate of a solid in a liquid is studied by weight loss measurements or analysis of the solution at known time intervals. However, if the solid is a metallic conductor, on which a redox reaction can occur at the metal-solution interface, it can be studied by electrochemical techniques. Electrochemical measurements have the advantage that the overall reaction can be separated into its components, in some cases by electrical measurements alone, and in others by a combination of these with analytical determinations.The overall equation for the dissolution of gold in aerated cyanide solution may be written4Au + 02+ 8CN- + 2H20 = 4Au (CN)2- + 40H- ..... (1)which can be separated into the two electrochemical componentsrepresenting the oxidation of gold and the reductionof ogygen respectively.4Au + 8CN-,= 4Au(CN)2- + 4eand O2+ 2H20 + 4e = 40H- These two reactions occur at the gold-electrolyte interface and it is the purpose of this paper to discuss the mechanism...

Jan 1, 1964

In 1961, West Australian Petroleum's Eneabba No. 1 bore encountered 22 seams of coal totalling 40 ft in thickness between the depths of 6373 ft and 6441 ft. On analysis, this coal had a similar calorific value (8000-HOOO B.T.U./lb, assuming 20 per cent water) to the coal from the Collie Coalfield, Western Australia's only known area of commercially exploitable coal. Being buried to depths in excess of 6000 ft, the coal at Eneabba had developed weakly-coking properties, and thus, although much younger than the Permian coals of Collie, gave promise of being a major potential source of power for Western Australia.West Australian Petroleum undertook a programme of stratigraphic drilling and shallow test drilling to determine whether this coalhorizon persisted into the outcrop of the Lower Jurassic sediments in the Hill River district, 140 miles NNW. of Perth, and, if it was present, if the quality and quantity of the coal would warrant development of the deposits by open cutting. The coal horizon was identified in the near surface, but the poor quality of the coal and the complexity of the structure made development (in the area examined) uneconomic at the time.A strong seismic reflection in the Eneabba area occurs at the same depth as the Jurassic coals. This event originates within the upper beds of the Lower Jurassic and it is probable that the velocity contrast between the higher velocity siltstones and the very low velocity coals enhances this very strong, distinctive seismic reflection.This event can be followed on continuous seismic data over a large area of the northern Perth Basin, from 13 miles SE. of Dongara to 20 miles SW. of Coorow. It can be followed from a depth of 4000 ftnear Dongara to over 17,000 ft to the SE., so development of thisvast potential source of power will depend on the economics ofprocesses being developed for the production of power from theburning of coal seams in situ.INTRODUCTIONThe discovery of 22 seams of economically useable coaltotalling 40 ft in thickness in the Lower J urassic sedimentsof the Eneabba No. 1 bore (Fig. 1) led to the search forthese seams at economically workable depths. The Ministerfor Mines in Western Australia granted to West Australian1. Supervising Geologist, West Australian Petroleum Pty. Ltd.Manuscript received at The Institute, 25th May, 1964. and presented to the 1964Annual Conference.

Jan 1, 1964

By C. O. Karacan, S. J. Schatzel, W. P. Diamond

In coal mining, longwall mining is a preferred method to maximize production by extracting large blocks of coal that have been outlined with a set of development entries. In U.S. mines, longwall panels are typically 305 m (1,000ft) wide (with a continual trend towards even wider panels), and usually over 3,050 m (10,000ft) in length. The increasing size of longwall panels, while helping to increase coal production, may also increase methane emissions due to the exposure of the mining environment to a larger area of fractured, gas-bearing strata. Thus, understanding the impact of increased panel widths on methane emissions, and designing gob gas ventholes and bleeder systems accordingly, can enhance the safety of the underground workforce by reducing their exposure to potentially explosive accumulations of methane/air mixtures. As part of its mine safety research program, NIOSH’s Pittsburgh Research Laboratory has initiated a reservoir modeling effort to better understand the interaction of the various geotechnical factors influencing gas flow within and to the underground longwall mining environment. A focus of this modeling effort has been 1) the prediction of the incremental amount of methane emissions to be expected due to increasing longwall panel widths, and 2) optimizing gob gas venthole completion practices to capture more of the gas in the subsided strata above longwall panels before it can enter the ventilation system of the underground workplace. The history matching phase of the study has been carried out on a 381-m (1,250ft) wide panel in the Pittsburgh Coalbed. Simulations have also been completed for a 442 m (1,450ft) wide panel to estimate the incremental increase in methane emissions and the performance of current gob gas venthole placement configurations. Additional venthole placement configurations were simulated to investigate options for optimizing methane capture from the subsided strata above the wider longwall panel.

By G. Warren

"In the past, smelting and refining of the precious metals recovered from ore has been generally looked upon as a small and relatively minor component of the business of gold mining. This is not surprising when one considers that the manpower, space and capital components of a gold refinery at an operating mine can be several orders of magnitude smaller than other unit operations at the same location. This philosophy is changing however, as economic and environmental pressure are forcing a re-evaluation of all aspects of gold mining and milling.This paper describes and evaluates three furnace technologies available and used by precious metal operators. The operation of arc, induction, and reverberatory furnaces are discussed and their strengths and weaknesses with respect to capital cost, impurity removal, slag quality, and environmental concerns highlighted.INTRODUCTIONIn the past, smelting and refining of precious metals recovered from ore has been generally looked upon as a small and relatively minor component of the business of gold mining. This is not surprising when one considers that the manpower, space, and capital components of a gold refinery at an operating mine can be several orders of magnitude smaller than other unit operations at the same location. Generally, gold producers will spend a great deal of effort to squeeze the last drop of efficiency out of a leach or grinding circuit via simulation or testwork but will design and build the refinery based upon past practices or industry standards. That past practices or industry standards will provide a functional refinery is undisputed; that this philosophy achieves the efficiencies that are possible or demanded in other plant operations is debatable.Environmental and worker hygiene requirements are considerations as well. Pollution control equipment can become a substantial contributor to both the capital and operating costs of a refinery and furnace selection has a marked influence upon the type and cost of this equipment. Slag characteristics and subsequent processing options available also play a role in furnace selection as precious metal slag losses and the recovery effort can greatly influence the cost / benefit analysis of a particular technology."

Jan 1, 2001

By Parker A. J, Muir D. M

Solutions of acetonitrile in water dissolve water soluble copper(I) chloride. Removal of volatile acetonitrile from the resulting solutions, by distillation with low grade steam, precipitates pure copper(I) chloride. This is used to purify a crude copper chloride sublimate from the chlorination of nickel matte but is applicable to other sources of copper(I) chloride. The pure product can be converted to pure copper(I) oxide, copper(II) oxychloride or pure copper metal directly.

Jan 1, 1980

By Keith D. Rosbury

The basic objective of this project was to determine the cost-effectiveness of dust control used on unpaved mine haul roads. Field testing was conducted at three surface coal mines (two in Wyoming, one in southern Illinois) for a total of 20 weeks. The highest control efficiency measured for a chemical dust suppressant, 82 percent, was for calcium chloride two weeks after application. Generally, however, the control efficiencies hovered in the 40 to 60 percent range over the first two weeks since application, and then decreased with time. After the fifth week, the limited number of data points suggest a control efficiency of less than 20 percent. Composite watering data were fairly uniform. Watering once per hour resulted in a TSP control efficiency of approximately 40 percent. Doubling that application rate increased the control effectiveness by about 15 percent to 55 percent. Chemical dust suppressants (primarily salts and lignons) can be shown to be more cost-effective than watering under some conditions. Data summaries and the analysis of data are contained in Volume I. Volume II contains basic data.

Jan 1, 1983

By Edward C. Stephens, Robert R. Coats

High-grade copper ore was discovered in 1932 in the long-dormant Mountain City (Cope) mining district, Elko County, Nevada. From 1932 to 1947, the one producing mine in the district, the Mountain City Copper Mine, produced 1,109,878 short dry tons of ore averaging 9.745 per cent copper, 0.274 ounces of silver, and 0.0057 ounces of gold per ton. The Mountain City Copper Mine is developed in eugeosynclinal rocks of Ordovician age, the Valmy Formation, which is part of the upper plate of the Roberts Mountains thrust. On the Valmy were deposited unconformably first, a elastic formation of Devonian or Mississippian age, the Grossman Formation, succeeded unconformably by a ·sequence of three conformable formations, the Banner, the Nelson, and the Mountain City. The Banner Formation probably is early Late Mississippian in age; the ages of the Nelson and Mountain City are not known precisely but are believed to be of Late Mississippian and Carboniferous(?) age, respectively. A thick formation of elastic rocks, limestone, and volcanics, the Reservation Hill Formation, has been thrust over the Mountain City. The age of the Reservation Hill is unknown but is presumed to be Pennsylvanian(?) and Permian(?). Several plutons of Cretaceous quartz monzonite intrude the Paleozoic formations; they and the intruded formations have been laid bare by erosion, and several sequences of volcanic rocks of Miocene and Pliocene age, and perhaps in part older, have been successively deposited on irregular erosion surfaces. The primary mineralization of the Mountain City Copper Mine is believed to postdate the deposition of the Nelson Formation and to predate the intrusion of the quartz monzonite. The primary ore bodies are lenticular in shape and are composed largely of quartz, pyrite, and chalcopyrite. The ore lenses, in general, strike northwestward and dip northward. They occur in the Valmy Formation within a definite stratigraphic sequence composed largely of shales with associated minor quartzite lenses. The ore is epigenetic. The principal ore body, the "200," was completely leached to the 200 level. Abruptly beneath the barren gossan was supergene copper sulfide ore, much of which assayed 50 per cent copper. The secondary copper minerals are sooty and massive chalcocite, bornite, and covellite. The supergene enrichment of the ore may have required a large part of Tertiary time.

Jan 1, 1968

By B. Spigarelli

Carbon dioxide sequestration by conversion to carbonates has become a promising option for CO2 storage. Experiments were conducted to determine the feasibility of CO2 sequestration at ambient conditions using a Ca-rich industrial waste in a carbonate solution. The Ca-rich industrial waste used in this study was lignite fly ash. Fly ash was chosen because it is cheap, available near large CO2 point sources, already in powder form, and reactive due to amorphous properties. In the experimental set-up, CO2 absorption was inferred by monitoring feed and exhaust gas CO2 concentrations. The addition of an alkali to a fly ash-distilled water solution provided a 50% increase in CO2 absorption of the solution. Absorption time also increased by 50% compared to a fly ash-distilled water solution. TGA analysis was used to determine the extent of CO2 sequestration in the carbonate form. At a liquid to solid ratio of 20:1, the conversion of ?free? calcium to carbonates was 75%. A CO2 balance on the system concluded that at the current operating conditions 42% of the total CO2 fed to the system was sequestered in the carbonate form. SEM-EDS analysis of the fly ash particles before and after reaction with CO2 indicated that the carbonate compound being formed was calcium carbonate. The analysis identified rhomboidal structures on the surface of the fly ash particles after reaction with CO2, but not before. These rhomboids are characteristic of calcium carbonate formation and they had higher Ca, C, and O concentrations than the host spheres, suggesting calcium carbonate formation.

Jan 1, 2012

By C. Slotta, F. Charlier, P. Blomen

"Within the energy concept of the German government, the operating time of nuclear power plants was initially extended from about 8 to 14 years. It is planned, however, that every power plant will gradually be decommissioned until 2025 and that simultaneously the amount of renewable energies will successively be expanded. According to the political state, nuclear energy is a discontinued model. Looking at the global energy market, though, an obviously opposed development can be observed. At the moment, 443 nuclear power plants are running worldwide and further 62 facilities are being built. These about 500 nuclear power stations have to be supplied with nuclear fuel right now and in the future. The present paper will describe the worldwide use of nuclear energy, the extraction of the nuclear fuel uranium and in detail the available and predicted resources of uranium. The conclusion of the paper is the statement that uranium as nuclear fuel is no scarce resource but sufficiently available."

Jan 1, 2011

By B. P. Watson

The Bushveld platinum group metal deposits are two distinct, shallow-dipping stratiform tabular orebodies which strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 300 m. The mining method is a variation of planar open stoping. Pillars are widely employed to support the open stopes. In the deeper levels, in-stope pillars are required to fail in a stable manner soon after being cut, and the residual pillar strength is used to stabilize the hanging wall. These pillars are commonly known as crush pillars. Little work has been done in the past to determine pillar peak and residual strengths, and pillars have been designed using experience and formulae developed for other hard-rock mines. This has led to over and undersize pillars with consequential loss of ore, pillar bursts and potential collapses. This paper describes a crush pillar design methodology, and provides design charts. Three mining environments were incorporated in the investigations, which included underground and laboratory measurements, analytical solutions, numerical model sand back analyses. The results of the study are suitable for the areas where the research was carried out, and may also be applied with caution in other similar environments.

Jan 1, 2010

By Christian Ottergren

"Modern crushers offer double the capacity and performance of classic models. In some cases crushers are replacing SAG circuits, the advantages being smaller investment and lower operating costs. Is Tertiary crushing replacing SAG milling as the most optimal grinding method? Does tertiary crushing achieve the same outcomes as SAG milling? This paper considers these questions and provides an assessment of the strengths of tertiary crushing in comparison to other methods. Two case studies: a Scandinavian Platinum Project, and CODELCO, are also presented.INTRODUCTIONResearch on basic parameters in crushing started at Chalmers University in 1993. The initial project has developed and now involves several related areas. Modelling in accordance with new theories has resulted in modified designs which have been implemented and shown improved performance at operating mines in Chile. Sandvik Rock Processing is a partner and a major supporter of this program. This paper will cover some of the achievements and give references to the research reports.The mining industry has for many years mainly used crushers of the traditional 7’crusher concept, with thread adjustment of the setting and with a spring or hydraulic overload system. This machine type has been the workhorse for crushing throughout the world. The explanation for the dominance of this machine is that it has a reliable mechanical design. It can be estimated that about 2000 crushers of this design are still at work.Technical development in all fields utilizes new technologies like high-strength materials, advanced control systems and more extensive use of hydraulics. This is the reason why today’s motorcars, for example, are more efficient, more reliable and more environmentally friendly than their predecessors in the 1950s. Crushers are no exception. This paper will cover experience from the latest-generation cone crushers developed by Sandvik Rock Processing.The parts in this paper related to the CODELCO ElTeniente copper mine in Chile are coauthored with responsible personnel from the operation at the mine."

Jan 1, 2004

By Raymond P. Miller

This two volume report addresses slope stability of surface mine spoils within the Interior Coal Province. Sixteen (16) mines were visited, pertinent data and samples collected, and reported spoil instabilities back-analyzed. Laboratory test results are compared to back-analyzed material properties. Available methods of slope stability analysis are reviewed and evaluated with respect to application to mine spoil stability evaluation and prediction. Correlation and tentative relationships among spoil material properties, highwall conditions, mining equipment and procedures and empirical observations are presented. Slope stability sensitivity plots illustrate the relative significance of various input parameters on stability. Slope stability input parameters are correlated with site and mining conditions to identify the primary factors controlling spoil stability. Investigative methods, spoil stability enhancement techniques, spoil stability prediction procedures and future study areas are discussed. Appendices include a glossary of terms, annotated bibliography, details of mine visits, and detailed laboratory test procedures and results.

Jan 1, 1979

By Gerald Stolarczyk

The Radio Imaging Method (RIM) is based upon electromagnetic (EM) wave propagation in the coal seam waveguide. The radio geophysics theory underlying RIM was developed by Hill of the national Institute for Science and Technology (Hill, 1984). Recent advances in radio geophysics instrumentation have increased operating range in the coal seam waveguide to almost 3,000 feet. This paper describes RIM longwall panel reconnaissance scans and tomography results.

Jan 1, 2006

By J. E. Nesset, L. S. Urbanoski, J. R. Goode

"The benefits and advantages of pre-competitive, collaborative industry/university research are not always well appreciated. This paper presents the case study of a current collaborative project between CAMIRO-Metallurgical Processing Division and McGill University that is investigating the understanding and prevention of sphalerite activation in lead and copper-lead flotation circuits. The benefits of the research findings to the sponsors can be maximized by an approach which links the researchers themselves with the sponsors at frequent, interactive project review sessions. Some examples of the findings and their application to industry are also presented along with a general update on CAMIRO-MPD.INTRODUCTIONThe history of Canadian efforts in the area of collaborative pre-competitive research is not long when compared to Australia (AMIRA) and Britain (MIRO). AMIRA (Australian Mineral Industry Research Association) began over 40 years ago and has had a well recognized role in bringing together industrial sponsors and researchers to fund a large variety of very significant development projects in that country, The total AMIRA funding effort for mineral processing work currently exceeds some $Aus 40 million with new projects valued at about $Aus 12 million initiated each year. This high level of commitment by industry has contributed to establishing Australian researchers and their facilities as among the best in the world.Canadian companies have traditionally funded much of their R & D in-house with extensive facilities and large funding commitments. The past 2 decades have seen most of these facilities disappear. The current situation is one in which only the largest integrated metal and mining companies have retained their own R & D groups (e.g. INCO, Falconbridge, Noranda). Industry-funded research at universities was primarily through individual efforts by the mining companies and rarely included collaboration with other mining companies, equipment or chemical suppliers, or engineering firms."

Jan 1, 2001

By Ellis S. Hertzog, James R. Cudworth

Tremendous interest has been evidenced in the subject of dewatering and drying ooal for the past 10 years, and yet little effort has been made to summarize the literature, at least so far as this country is concerned. Only a few published articles have dealt solely with dewatering and drying coal. In most cases the subject has been discussed briefly, either in general terms or as to specific installations. It is desirable that a compendium be prepared collecting in one place information on the dewatering and drying of coal, the needs for this process in various fields, the available equipment, and the current American practice in regard to it. This work was underta..lten by the :Bureau of Mines in cooperation with the University of Alabama. New coal-washing plants in which various types of dewatering and drying equipment were in operation were visited in-Pennsylvania; Ohio, India...~a~ and Illinois. The dewatering·and drying of coel has .been studied in this coimtry by the Surface Preparation ·Committee of the ·coal Operato~s• Committee of the .American Mining ·Oongress. In GermaIJY .it has received the special attention of the Reichskohlenr·at, and in Great Britain of the Utilization of Fuel Commi-t-tee of the Insti ti.ite of Min"ing Engineers.

Apr 1, 1938

By M. B. Fonseca

Risk quantification in grade-tonnage curves is critical for capital investment in mining projects and can be obtained through geostatistical simulations of orebodies. A practical difficulty may arise in multi-element deposits, as the joint modelling of the related attributes using the traditional co-simulation approaches is computationally intensive and may be impractical for use in the industrial environment. This paper presents the construction of risk-integrating grade-tonnage curves for a complex copper deposit in northern Brazil, by jointly simulating its key geochemical attributes of interest: Cu, Fe and K. The joint conditional simulation of these elements is based on Minimum/Maximum Autocorrelation Factors (MAF). MAF is an approach, based on principal components, that spatially decorrelates the variables involved to non-correlated factors. MAF’sspatial decorrelation at any lag distance is the main and critical difference of this approach from the principal component approach attempted in the past. In the MAF approach, the independent factors are individually simulated and back-transformed to the conditional simulations of the correlated deposit attributes that reproduce the cross-correlations of the original variables. Keywords: Joint simulation; mini/max autocorrelation factors; grade-tonnage curves.

Jan 1, 2003

The poor reconciliation between the values of estimated and actual grades can cause major economic losses to the mining industry. In a mining operation grade reconciliation is comparing the values of estimated grade calculated in exploration stage with actual grade obtained from blastholes' data. Many different factors affect the degree of reconciliation in a mining operation. In this paper we investigate the factors related to estimated grade which affects the reconciliation process in the exploration stage of the orebody. These factors are the sources of uncertainty in the rest of mine life. In this area the most important factors are inherent variability, statistical uncertainty and systematic uncertainty. A probabilistic model was presented to model each source of uncertainty. The implementation of proposed model was checked and its validity was investigated using real data in an iron open pit mine in Iran.

Dec 6, 2010

By Luis Bernal, Pertti Lamberg

"SkimAir®, Outotec’s Flash Flotation unit, is placed in the grinding circuit to float the valuable liberated mineral particles from the circulating load of the grinding process while still relatively coarse. Esperanza copper-gold deposit located near Sierra Gorda, Chile, hosts 535 Mtn ore grading 0.57 % copper, 0.27 g/t gold. A series of laboratory and pilot flotation tests were conducted to find out the flotation performance of different ore types both with and without the Flash Flotation. This data was used in modeling and simulating to find the optimal flow sheet for the highest Au and Cu recoveries with required Cu concentrate grade. Simulations with the HSC Chemistry 6.1 software showed that with the SkimAir® and Flash Cleaning it is possible to achieve the required copper grade of 27% Cu with 5% higher recovery for gold and 2% higher recovery for copper compared to the circuit without the Flash Flotation. The pilot tests with simulations were the back up for the installation of four Outotec SkimAir® SK 2400 Flash Cells in the Esperanza circuit for the processing 95.000 tpd of copper-gold ore.INTRODUCTIONEsperanza copper-gold deposit is located near the town of Sierra Gorda, 2nd Administrative Region in Chile. Deposit hosts 535 Mtn ore grading 0.57 % copper, 0.27 g/t gold. The main copper minerals are chalcopyrite and bornite. Gold is carried by native gold and solid solution of copper.Antofagasta Minerals S.A. conducted a series of flotation studies at SGS Minerals Services. The studies included both laboratory and pilot scale work. In the pilot scale study the applicability of the Flash Flotation technology was studied with High-grade Andesite and High-grade Porphyry samples (SGS Mineral Services). The Flash Flotation technology gave significantly higher recovery for gold than the conventional flotation circuit. The recoveries for copper were slightly higher using the conventional flotation."

Jan 1, 2009

By A. K. Mukherjee

The roles of pulsating mechanisms such as the amplitude and frequency of the jig cycle are well established in jigging. Also well established are the roles of the size ratio and the volume fraction of the feed. In iron ore beneficiation plants, these process parameters are optimized to achieve the highest efficiency. However, the role of one of the more important feed characteristics, the liberation characteristic of the feed, has not been studied in detail. Evaluation of the liberation characteristics is difficult because the required washability test is not viable for iron ore feed. In this paper, a new method is proposed in which the liberation characteristics are measured through a separation efficiency value. In the new evaluation method, jigging parameters such as amplitude and frequency of the jig cycle are optimized from the fundamental understanding of the process dynamics and feed characteristics such as size distribution. Then, feeds with different liberation characteristics are tested to evaluate the liberation characteristics of feed in jigging.

Jan 1, 2008

By James P. Stewart

This case history describes the engineering design and construction for the Contractor of a 35-ft-deep excavation for an 800-square-foot addition to an existing sewage pump station. The site posed unexpected geotechnical complications that included deep gravelly soil, a history of local construction difficulties, groundwater consisting of heavy salt brine, and the need to underpin the existing pump station. The project took an interesting twist when the Owner issued a change order limiting the dewatering discharge to a fraction of that required to lower the water table. This documents the interesting circumstances of this job and documents the unusual subsurface conditions in the Syracuse, NY Lakefront area.

Jan 1, 2003