Search Documents

By T. Iriyama, Y. Fujita, R. Omatsuzawa, T. Nishio, N. Okochi

Sm-Fe-N hard magnetic materials are good candidates for high performance bonded magnets. Rapid-quenching method should be highly favorable for the fabrication of isotropic magnet powder with high coercivity. We report here the magnetic properties of Sm-Fe-N powders produced by a few kinds of rapid-quenching processes. Sm2Fe17 powders were prepared by gas-atomization (GA), rotating-disk atomization (RDA), or melt-spinning (MS) method. The Sm2Fe17 GA powder had dendritic solidification structure, while the RDA powder had micro crystalline structure with size of 3-5 µm. Coercivities (HcI) of their nitrides were 56 (for GA) and 217 ka/m (for RDA). The H cI of nitrided Sm2Fe17 MS powder with wheel velocity (V5) of 5-20 m/s, which had also microcrystalline structure, was 53 to 509 Wm. These coercivity values are not sufficient for bonded magnet applications. From the study of additive effects, it was found that C, C-Si, C-Ga, or C-Al addition decreased the crystal size of quenched Sm2Fe17 powder. Consequently, high coercivity was obtained; the HcI of nitrided Sm2Fe1C1Si1 MS powder with V5 of 10 m/s was 898 kA/m, and 708 kA/m for the nitrided Sm2Fe15C1Si1 RDA powder. The compression-molded bonded magnet made from Sm2Fe18Si0.1Nx MS powder showed a high (BH)max of 82.7 kJ/m3.

Jan 1, 2000

By Sijun Li, Bingyu Zhang, Haitao Zhou, Zhendong Zhang, Guofei Si, Xianghua Liu

"Hot compression test of Nb microalloyed coiled tubing steel is performed on Gleeble3500 at 1123K—1373K and strain rate from 0.001 to 5s-1. It is found that flow softening occurs and the flow curves exhibit a peak with a characteristic of dynamic recrystallization (DRX) and change with temperature and strain rate significantly. The peak stress and peak strain are dependent on the Zener-Hollomon relationship with activation energy of 390 KJ/mol. On the basis of Avrami equation and the Zener-Hollomon parameter, it is obtained that the dynamic recrystallization kinetics equation with which the calculated and measured recrystallization fraction is very close. On the results of hot compression test, the Nb microalloyed coiled tubing steel is rolled by Thermo-Mechanical-Control-Processing (TMCP), and it is obtained that the yield strength and tensile strength of Nb microalloyed coiled tubing steel are 565MPa and 685MPa respectively, and the elongation percentage is 30.1%.IntroductionCoiled tubing is widely used in oil field for well logging, well completion, drilling, work over and other operation in various fields to solve a number of conventional operating techniques problem which are difficult resolved, and it plays a more and more important part in exploration and production at oil field. [1] It will improve the efficiency of exploration and exploitation, studying, developing and using coiled tubing technology. Therefore, the development of domestic coiled tubing materials and manufacturing technology are great significance. It is well known that Coiled tubing has relatively poor working conditions and complex force state. So, the coiled tubing needs satisfier a kind of high strength, high plasticity, and corrosion resistant under complex oil gas condition. As the coiled tubing technology developed, the level of the coiled tubing steel is from CT55 originally to CT90 and CT100, and the corresponding tensile strength is 483MPa-758MPa. [2, 3]"

Jan 1, 2012

By John O. Marsden

In early 1998, Phelps Dodge embarked upon a program to investigate alternative technology for the extraction and recovery of copper, and other metal values, from copper concentrates. A review of all of the available process alternatives indicated that many were unsuitable for large-scale commercial application and others were clearly targeted at niche applications where contaminants (and consequently smelter penalties) were driving the decision-making. The result of this development program is the world?s first commercial application of high temperature pressure leaching of chalcopyrite concentrate at Bagdad, Arizona, which was commissioned in the second quarter of 2003. Other related processes are in various stages of development. In addition to the obvious considerations, the economic aspects of this technology have been considered in detail at each step in the development of the program. The technology developments in this area are reviewed with emphasis on the economic viability and commercial application.

Jan 1, 2003

By Guray Kaya

Boron minerals are widely employed in various fields such as ceramic, glass, cement, metallurgy, etc. Although boron deposits of the world are limited, the production level of boron-based products is continuously increased. Turkiye possesses approximately 73 % of total world boron resources. Etibor Kirka Borax Company of Turkiye produces tincal concentrates and borax pentahydrates. During such productions considerable amounts of concentration and derivation wastes appear. Having considered the increased rate of production it is quite obvious that the level of relevant wastes will also be raised. With this study it was aimed to utilize these wastes in roof tile and brick bodies and to convert them into a form environmentally and human friendly. Newly produced products were undergone to several standard tests for the determination of their shrinkage, water absorption, strength values and coloring parameters. Additionally, micro structural studies were conducted.

Jan 1, 2006

By Wentao Guo, Xuefeng She, Qingguo Xue, Jingsong Wang

By the coke gasified reaction device and online measurement high-temperature compressive strength apparatus, the variation of pore structures of coke after gasified reaction with CO2 and H2O was investigated. Research illuminating the influences of solution loss rate, temperature, and carbon species on compressive strength of coke was also carried out. The results showed that the total compressive strength was higher than for the reaction with CO2. The high-temperature compressive strength of coke decreased with the increasing of solution loss ratio or temperature after reacting with CO2 and H2O. At the same solution loss ratio, the damage of pore structure to coke strength after gasified reaction with H2O was relatively smaller and the deformation resistance was stronger when compared with that in CO2.

Jan 1, 2016

By Joo Hyun Park

A history of the research regarding the spinel in the community of the stainless steels has simply been reviewed, followed by the recent studies for the formation mechanism of the spinel in the ferritic stainless steel melts equilibrated with the highly basic slags and the crystallization behavior of spinel phase in the calcium aluminosilicate melts containing MgO and CaF2 during slow cooling cycles. It has been proposed that the content of aluminum and calcium in the steel melts as well as the basicity and the content of MgO and Al2O3 in the slags are quite important factors affecting the spinel formation in view of the formation mechanism based on the reduction of MgO (or CaO) and Al2O3 in the slags by the aluminum and silicon added to deoxidize the molten steel. The use of magnesia refractory was also recommended. The formation mechanism of spinel from the MgO inclusions readily formed in the steel melts equilibrated with the highly basic slags has newly been proposed on the basis of the ionic exchange reactions at the inclusion/metal interface and the crystal chemistry of oxides. The crystallization behavior of the spinel phase in the calcium aluminosilicate melts was enhanced by the Al2O3 based on the ionic reaction of spinel formation in the oxide melts, while the size of the spinel crystals in the oxide melts decreased by addition of CaF2.

Jan 1, 2006

By Mahmood Alemrajabi

When LKAB processes their iron ores in northern Sweden, they generate apatite as a by-product. The apatite has been recovered by flotation and the concentrate contains about 0.4 wt% rare earth elements (REE). Both phosphate rock and REE are listed as critical raw materials for the European union. In the present study, the recovery of REE within the nitrophosphate process of fertilizer production has been studied. In the first stage, the REE are precipitated and isolated as a phosphate concentrate. For further purification and individual separation of REE by solvent extraction, removal of phosphorous from the concentrate to enhance the dissolution of REE in mild acidic solutions is essential. In this study, thermal treatment of the concentrate with sodium hydroxide at elevated temperatures followed by water leaching has been studied in order to separate the phosphorous and thereby facilitate dissolution of the REE. The results show that 95% of total phosphorous initially present in the REE phosphate concentrate is removed after thermal treatment with NaOH 1:1 mass ratio, at 400 °C.

By Xiaojie Gao, Shufeng Yang, Jingshe Li, Chengsong Liu

In the blast furnace process, the dust entrained in the blast furnace gas enters into the down-comer, flows through the gravity dust separator (to eliminate coarse particles) and then is collected in a bag-house. The powder collected by the baghouse is called bag dust, while both fractions are called blast furnace dust whose main components are C and Fe. The dust also contains small amounts of nonferrous metals such as Zn and Pb, which have some value. Also, due to the small particle size and low density the dust is easily suspended in air and so can endanger human health. Therefore it is necessary to develop a process to both treat the dust to recover the metal values and to dispose of the residue – preferably by recycling to the blast furnace itself via the sinter strand. These objectives will result in good economic, environmental and social benefits [1].

Jan 1, 2014

By Manolete Mena

WC-Co nanocomposite powder is among the first group of materials with a promising potential for nanocrystalline-materials application. A chemical vapor synthesis (CVS) process that has previously been used for preparing the aluminides of titanium and nickel, and other metallic and intermetallic powders has been applied to the preparation of WC-Co nanocomposite powder. This CVS system was designed so that a tungsten precursor (WCl6 powder) and a cobalt precursor (CoCl2 powder) were separately fed into each evaporator in a reactor by means of specially designed powder feeders. The reduction and carburization of the vaporized chlorides by methane-hydrogen mixtures produced nanosized WC and Co composite powder. The product is a very uniform mixture of the constituent powders, which is important to ensure a high quality of the bulk cemented tungsten carbide product after consolidation. In the present work, the effects of reaction temperature, CH4 to WCl6 ratio, CH4 to H2 ratio, residence time, and Co content on the powder composition and particle size were determined. The products were characterized using XRD, carbon analyzer, and TEM.

Jan 1, 2006

By C. F. Ferron

A process has been developed to treat the copper gold ores from the Guelb Moghrein mine in Mauritania. The process consists of pressure leaching the sulphide concentrate, neutralising with the oxide ore, recovery of copper by SX/EW and of gold by cyanidation of the autoclave residue. This paper focuses on the pressure leaching step, and presents data from bench and pilot plant test programs. In particular, attention is drawn to the effects of temperature, grind size, neutralisation, retention time and solution recycle on the kinetics of copper dissolution from various flotation concentrates. Likely leach mechanisms are briefly discussed.

Jan 1, 2000

By Truan-Sheng Lui, Li-Hui Chen, Hao-Wen Hsueh, Fei-Yi Hung

"Since Ag wires have similar hardness and bonding properties to Au wires, they can be applied in some pads. In the present study, the annealing effect (at 225°C~275°C for 30min) on the tensile mechanical properties of silver wires with f=23µm was investigated. In addition, the micro-structural characteristics and the mechanical properties before and after an electric flame-off (EFO) process were also studied. Experimental results indicate that with annealing temperatures of more than 250°C, the silver wires possessed a fully annealed structure, the tensile strength and the hardness decreased, and the elongation was raised significantly. Under the thermal effect of EFO, the necks of the Ag balls underwent recrystallization and grain growth was induced, and the annealed Ag wires had a shorter zone of HAZ (220µm). The bonding strength and the neck-strength of the Ag wires were more than 7gf and possessed excellent bonding properties.IntroductionThermosonic ball bonding is one of the preferred processes for electronic packaging to connect a semiconductor chip and a lead frame by a thin metal wire. At present, gold wire and copper wire are the preferred interconnect materials to bond with the aluminum metallized wafer pads [1, 2]. Since gold is expensive and the reliability of copper is poorer [3], the study of silver wire has attracted a lot of attention already. In addition, the inherent properties of high ductility and low hardness of silver as well as its workability effectiveness compared to gold, have made it a preferred alternative .[4, 5]"

Jan 1, 2012

By P. A. Davidson

"We discuss the influence of a static magnetic field on jets, vortices and turbulence. This is particularly relevant to D.C. braking in slab casting. Our main conclusion is that, typically, the magnetic field destroys mechanical energy, via joule dissipation, but is unable to destroy momentum. Rather, it continually rearranges the momentum in such a way that the energy falls.IntroductionIt is well-known that a static magnetic field can suppress motion of a liquid metal. That is to say, movement of the liquid across the magnetic field lines induces a current. This leads to Joule dissipation and the resultant rise in thermal energy is accompanied by a corresponding fall in kinetic energy.This phenomenon has been exploited in a range of metallurgical processes. For example, in the continuous casting of large steel slabs, an intense, static magnetic field is commonly used to suppress motion within the mould. The objective is to keep the free surface of the liquid quiescent, thus avoiding the entrainment of surface debris. In other solidification processes, such as techniques for growing semi-conductor crystals, it is widely believed that natural convection has a detrimental effect on the metallurgical structure of the solid. Again, the imposition of a static magnetic field is seen as one means of suppressing these unwanted motions. Finally, magnetic damping is used in the laboratory measurements of chemical and thermal diffusivities, particularly where solutal or thermal buoyancy can disrupt the measurement technique.In this paper we shall look at the damping of jets, vortices and turbulence. Our aim is to present a unified theoretical framework from which the many published studies may be viewed."

Jan 1, 1999

By A. Kapilashrami

Slag foaming proves to be both blessing and curse for the process productivity, depending on where in the process it occurs. In pyrometallurgical processes, slag foaming is often a result of chemical reactions taking place in the slag. As the slag composition and reaction rates are changing, foaming occurs under dynamic conditions. In the present work, slag foaming was studied with XRF. The foam displayed a fluctuating behaviour, unaccountable by existing models. The concept of foaming index was found not to be satisfactory in describing the foam, resulting in the need for alternative theories. The rate of fluctuations was seen to be related to the difference between rate of gas generation and rate of gas escape from the system (Ug-Ue) as well as the bubble sizes. Thus, model development of dynamic foaming phenomenon has to take the effective chemical reaction rate as well as the bubble sizes into consideration. The first step in obtaining foam is to form bubbles. In the present work, gas bubbles were generated through chemical reaction at interface between two immiscible liquids and the bubble formation was studied optically. The gas bubble size was seen to be uninfluenced by the reaction rate. However, bubble formation was seen to take place in one of the phases and since the bubbles consequently traversed the interface under the influence of buoyancy, the viscosity of the first phase was found to influence the final bubble size where increased viscosity would yield a larger bubble size.

Jan 1, 2006

By Matthew Jeffrey

Leaching, cementation, electroplating and flotation are all electrochemical phenomenon. They are also key processes in the hydrometallurgical treatment of metals. Unfortunately electrochemical methods tend to be under-utilized when studying these processes and one possible reason for this is the confusion surrounding the large number of electrochemical techniques available. In this paper four former PhD students of Professor Ian Ritchie present an insight into how one electrochemical technique can be used to compliment rate/kinetic studies. The paper details how to perform the experiments, interpret data, and recognize complications with the results. Examples where this approach has been highly successful are presented, and include: cementation of zinc by aluminium, cementation of copper by nickel, cyanide leaching of gold and the cementation of gold thiourea by mild steel. The examples illustrate that this universal approach adopted by Ian Ritchie provides the key to understanding the mechanism of many hydrometallurgical reactions.

Jan 1, 2003

By Toshitaka Ota, Hisao Suzuki, Minoru Takahashi

"Perovskite-type lead zinc niobate (PZN) exhibits excellent electrical properties such as high dielectric constant, high electrostrictive coefficient and superior piezoelectricity. Therefore, PZN ceramics are very promising for high performance electronic devices. However, perovskite phase PZN is not stable under the ambient atmosphere. Accordingly, it is very difficult to prepare single-phase perovskite PZN ceramics. In this study, A-site cation of lead was partially substituted for barium to stabilize the perovskite phase of the PZN (Ba-doped PZN) powder. In addition, molecular design of an alkoxide precursor was controlled for a low-temperature processing. As a result, molecular design to suppress the lead-volatilization during calcination was preferred for a low-temperature processing. Processing temperature for a single-phase perovskite was depended on the amount of barium dopant. Doping of20 mole% of barium resulted in the single phase perovskite at 900 °C. The temperature for the single phase perovskite of Ba-doped PZN powder, which depended upon the amount of Ba-doping, was lower than that of the powder prepared by the atmosphere controlled conventional powder processing at least by 150 °C.IntroductionFerroelectric thin films and powders with perovskite structure are of renewed interest for micro-electronic applications, including ferroelectric random access memory (FRAM), dynamic random access memory (DRAM), and thin-layer capacitors integrated onto a silicon wafer [1-3]. In addition, recent advancement in micro-machine requires a high performance micro-actuator [4]. A perovskite type relaxor of Pb(Zn113 Nb213)03 is one of the promising materials for a high performance capacitor and microactuator because of their high permittivity and electrostrictive coefficient [5]. Therefore, this paper focuses on the low temperature processing of Ba-doped PZN powders.Chemical solution deposition (CSD) from molecular-designed alkoxide precursor solution is one of the most promising techniques for processing high-performance powders and thin films because it offers precise control of compositions on a molecular scale as well as a low processing temperature [6]. However, chemical solution deposition of perovskite type PZN powders and ceramics are very difficult because of the formation of stable pyrochlore phases. Therefore in the past, PZN powders and single crystal have been prepared by the hydrothermal method or flux method as well as the partial substitution method of a A-site cation [7-10]. In this study, a suitable molecular design for a preparation of perovskite type Ba-doped PZN powders with a chemical solution deposition process is investigated as well as the effect of A-site cation substitution. Chemical solution deposition from molecular-designed alkoxide precursor solution is expected to decrease the amount of a A-site substitution and/or a crystallization temperature for a single phase perovskite. This paper describes ""the relation between molecular-design and processing temperatures for a single-phase perovskite of Ba-doped PZN powders in comparison with the conventional oxides mixing method."

Jan 1, 2000

By L. N. Ertzeva

The process for thermal treatment of current pyrrhotite concentrate in reducing environment with the use of disperse metal iron as an iron-bearing additive (optimal volume 20-30%), with downstream magnetic separation of the calcine, has been studied. The reduction process has been performed in conditions emulating those of both tube and fluidize-bed furnaces.

Jan 1, 2006

By K. V. Sreenivas Rao

Solidification experiments have been conducted to study the effect of interface heat flux and air gap formation on cooling rate of the casting during solidification of Al-4.5wt%Cu alloy. The thermal history of the casting and mold during solidification is recorded using thermocouples connected to computer interfaced data logger. The measured temperatures in the mold are used as input to the IHCP (inverse heat conduction problem) algorithm for simulating multiple heat flux components at the boundary. It is observed that the filling effects induce spatial variation in the thermal field in the mold and casting regions and greatly influence the cooling rate of the casting. The study demonstrates the use of IHCP and in-situ measured thermal profile in analyzing the cooling rate and microstructure.

Jan 1, 2008

By A. V. Tarasov, V. M. Paretsky

"Based on theoretical and experimental studies into the specific features of the mechanism, kinetics, aerodynamics and heat transfer parameters of the flame-type oxidation of metal sulfides in a stream of technical-grade oxygen, a three-dimensional deterministic mathematical model of an oxygen-flame smelting furnace has been developed on the basis of the zonal method for computation of heat exchange. The model is presented in the form of equations taking into consideration the radiation component of the selective radiation, the convection component of mass transfer between the space and surface zones, heating of charge particles due to heat conductivity, accretions formation on a multi-layer refractory lining with inserted cooling elements. The adaptation of the model for a full-scale furnace has demonstrated the possibility for its use for computation of main smelting process parameters. Multifactor model investigations were conducted and the results obtained were applied using statistical methods for development of a simplified computational regression model describing the interrelation of the main output parameters: temperatures of flame, lining, slag and off-gas; heat fluxes to the lining; thickness of accretions; heat removed by cooling elements; copper content of matte. On the basis of this model, a block diagram of the algorithm was developed for control of the thermal conditions of the furnace, as well as the control algorithm itself.IntroductionThis paper presents the results of an integrated modeling and development of principles for control of copper smelting process using as an example the oxygen-flame smelting process (KFP) for treatment of sulfide concentrates at the Kovoguty Krompahy copper smelter (Slovakia) with a capacity of 20,000 tpy of copper."

Jan 1, 2001

By Elsa Agante

Recycling of solid wastes, a common practice nowadays, requires the separation of the different materials in order to increase the products added value. The separation of one plastic from mixtures of different types of plastics is not easy due to their similar physical properties, but different techniques are available, from automatic sorting systems based on optical sensors to techniques adapted from mineral processing, namely gravity, froth flotation and electrostatic processes. In the last decade, many researchers have addressed the separation?s problem of different polymers, like Polyethylene Terephthalate (PET) and Polyvinyl Chloride (PVC), two polymers commonly used in packaging which have similar density. One proposed technique is the classical froth flotation performed in agitated cells. Froth flotation is a versatile and relatively cheap process widely used in mineral separation. It is based on the different behaviour of particles in the presence of an inter-phase air-water, which depends on the materials surfaces properties. Froth flotation can be affected by some variables such as impeller speed and air flow rate. Agitated cells, when used with low density materials, like plastics, can produce overstated turbulence that prevents the adhesion and collection of particles in the froths. In this case, separation is favoured by column flotation smoother hydrodynamics. This paper proposes the separation of PET from PVC by column flotation. The experimental work was carried out in a column of 9cm diameter and 1m high. The effects of some operating conditions, such as depressor and frother concentration, air flow rate and feed grain size on products grade and recovery were evaluated and the best flotation conditions for the separation of these plastics were established.

Jan 1, 2006

By F. Begazo

The most common approach to increase production in copper refineries is to increase current densities. However, if these increases are not well thought out beforehand and are not properly and effectively controlled, the end results could be reduced plant performance and a deterioration in cathode quality. Both of these factors result in lower efficiencies and increased costs. At the Ilo Refinery of Southern Peru Copper Corporation, a modernization and expansion program was implemented shortly after the Refinery was purchased from Minero Peru, in 1994. This program was intended to increase production from 195,200 mtpy of cathode to 227,000 mtpy over a 3-year period. Part of this production increase would come from increasing current density. During the period from 1994 to 1997, current density at the Ilo Refinery was increased from 218 A/m2 to 230 A/m2, while plant efficiencies were maintained at consistently high levels. The current efficiencies were maintained at >97.5% and time efficiencies were maintained at >98%. During 1998, additional increases in current density were implemented while the high plant performance was maintained at the same levels. By the end of 1998, the current density was 241 A/m2, while current efficiency and time efficiency of 98% were maintained. This paper describes the control processes used at the Ilo Refinery to maintain high plant performance levels while increasing the current density. Additionally, expected plant performances from extended test programs at current densities up to 280 A/m2, for future production increases, are reviewed and discussed.

Jan 1, 1999