Search Documents

By Erik Westman

Tomographic imaging, commonly known as a CAT-scan or CT-scan, is used in the medical field to generate a picture of the interior of a body. Current research is applying this method to bodies of rock so that rock failure can be better understood and predicted. This paper discusses the basic principles of tomography and describes recent developments in the use of seismic tomography in longwall coal mines, including results from a bump-prone longwall coal mine and continuing research.

Jan 1, 2003

By Joachim Leonhardt

Hundreds ofbolt-indicators were already used successfully in the German deep hard coal-mines to increase the safety and economy. The bolt-indicator offers the simple possibility to show roof-bolt (anchor-) loads. to indicate weak points as well as to optimize the anchor density and the dimension: The bolt-indicator is mushroom shaped and consists of coated metal. It is inserted between the anchor plate and the flanged nut. The loads appearing at the anchor are transferred to the bolt- indicator and can be recognized visually at the cylindrical part by the amount of the surface coating. Examples are used to clarify the application aims, operation and usage of the bolt-indicator and its yielding advantages in practice.

Jan 1, 2001

By Joseph A. Cybulski

In response to the mining of reserves with increasingly adverse round conditions and the roof support recommendations of current rock mechanics theories, roof support systems have continued to improve. A few of these newer bolting systems. while giving improved performance, require a new method to check bolt installation. Previous1 , a torque wrench had been the sole means to check the installed torque of a roof bolt. However, due to the characteristics of soma of the newer bolting systems which can prevent a reliable manual torque check and a recent change in the federal roof control regulations, an alternative method to a manual torque check is gaining acceptance. This alternative method improves monitoring the hydraulic pressure of the roof bolting machine torque circuit and provides a safe, reliable and quick wav to check bolt installation in those instance when an accurate manual torque check cannot be made.

Jan 1, 1990

By Megan N. Witkowski

The purpose of this study is to investigate the susceptibility characteristics of domestic and agricultural water supplies that may be vulnerable to diminution or total loss of supply when active longwall mining is in the vicinity of the potable aquifer systems of southwestern Pennsylvania. The study focuses on water supplies in Greene and Washington Counties with reported losses or reductions in supply that were attributed to the seven active longwall mines in operation between 2003 and 2008. The undermined water supplies represent a variety of hydrogeological settings and mining conditions prevalent in the southwestern Pennsylvania longwall coalfield. The susceptibility characteristics investigated include hydrogeological setting, proximal location to mining, and climatic conditions at the time of impact. The investigation considers the relationship between geological and mining characteristics. Geological characteristics include overburden composition and geomorphology of the surface; mining characteristics include mining method, depth, and extraction thickness. It was determined from the study that the average overburden thickness at each mine site is indicative of hydrological changes to potable aquifer systems, with the overall impact frequency at each site decreasing as depth to mining increases. However, depth to mining was not the governing factor when hydrological responses were determined on a case-by-case basis. To fully analyze and hopefully predict potential impacts by longwall mine subsidence, it is necessary to consider additional factors including topography, distance to mining, mining method, and climatic conditions at time of undermining. The investigation serves the purpose of enhancing our understanding of hydrogeological responses to longwall mining and will aid in predicting potential impacts to southwestern Pennsylvania?s wells and springs in proximity to future mining.

Jan 1, 2011

By S. Jayanthu

This paper presents analysis of strata behaviour with special reference to convergence and stress variation during an experimental trial of extraction of pillars with cable bolts as major support system in 6.5 - 8.0 m thick coal seam. Critical span for roof falls was estimated through empirical models and also evaluated by numerical models. In situ strata behaviour studies during 1992-96 for about 70 local/major falls revealed inadequacy of the available literature for interpretation and prediction of the roof falls. Convergence acceleration and variation of induced stress based on continuous monitoring data showed distinct anomalies and potential for better understanding of strata mechanics during pillar extraction.

Jan 1, 1998

By Frank Kendorski

Several startup or longtime underground stone mines have experienced unanticipated roof control difficulties due to the variable geologic character of the roof strata. Careful mapping of roof conditions, and identification of controlling geologic and mine geometric factors using sedimentological descriptors, lead to an understanding of the mechanisms causing roof problems. Types of bedding plane features can be categorized into geometric, internal structures, bedding-plane markings, deformed bedding, solution structures, and accretionary structures. Factors such as encountering open water-filled master joints; roof strata delamination due to internal water pressures; local karst features with mud, sand, and water hazards; and sudden loss of limestone roof due to paleo-channel erosion are some recent problems described.

Jan 1, 2002

By Jessica M. Wempen

Differential Interferometric Synthetic Aperture Radar (DInSAR), a satellite-based remote sensing technique, has been demonstrated as a potentially practical method for measuring mining induced surface subsidence. Unlike traditional methods of subsidence monitoring, DInSAR has the capacity to generate subsidence data on a regional mining scale with a relatively high data density. Using DInSAR to evaluate subsidence over large regions with relatively long time scales has the potential to help quantify the impact of subsidence in the mining region, and provide a means for validating whole-mine geotechnical models. In this study, nine pairs of interferometric data from the Japanese Advance Land Observing Satellite (ALOS) were processed using DInSAR to generate displacement maps for a group of trona mines in southwest Wyoming. The data cover a time span from December 2007 to March 2011. The maximum subsidence for one of the mines totaled 1.3 meters for this period. Cumulative DInSAR displacement maps show the development of subsidence over time. In this mining region, surface subsidence is generated primarily by extraction of trona using retreating longwalls. Additionally, trona is extracted by solution mining, which also generates measurable surface subsidence.

Jan 1, 2014

By Axel Preusse

Due to a political decision, German hard coal mining will come to an end in the year 2018. By then, there will have been more than 150 years of industrial grade mining activities. Located in the western part of Germany is one of the most densely populated areas of Europe. Multiple coal seams have embossed the earth?s surface up to 20 meters (21.87 yards), as mining has subsided. The aftercare of hard coal mining will consist of three tasks: groundwater management, polder management, and groundwater treatment. The Ewigkeitslasten (cost in perpetuity) at the current groundwater level has been determined in the past. The actual cash value is calculated to be about 12.4 billion euros (approximately 16.5 billion dollars). The cost of groundwater management is directly related to the groundwater level. Rising groundwater levels will reduce the cost of pumping water. Known effects of rising groundwater are uplift of the surface, emission of methane gas at the surface, higher risk of cave-ins, and contamination of drinking water horizons. Each of those processes produces cost in order to prevent negative consequences (e.g., uncontrolled methane emissions) or to handle reparations (e.g., damages caused by surface uplifts). In the long run, it is the goal to minimize the Ewigkeitslast. As a first step, all cost-generating processes are specified, and a cost type based characterization is performed. The objective of this case study is to identify key parameters to determine the quality of a cost-generating process (proportional cost, fixed amount cost). Afterwards, it is intended to specify the quantitative impacts of each parameter and to set up an optimization model to minimize the overall cost. The quantitatively specified parameters will form the base out of which the optimization model is created.

Jan 1, 2013

By Zhang Liandong

Roof control in thick-seam mining has long been a difficult problem in mine design and coal mining. In the early 1980's, through ground control instrumentation and investigation the rules of roof strata movement were determined, based on which the sliding roof bar powered support was properly designed and successfully applied to roof control to thick seam mining with caving. Underground trials in Huating Coal Mine produced satisfying results. The technique is being employed in many Chinese coal mines and won the national price for technical advance.

Jan 1, 1990

By Hamid Maleki

Results of geologic investigations, in-mine instrumentation, and numerical modeling are presented for two longwall mines in which pillars with large width-to-height ratios (8 to 9) are used. These investigations revealed that wide pillars unload when subjected to sufficient stress and that pillar unloading is influenced by geologic conditions. Field measurements in mine 1 clearly indicated load transfer from the longwall area toward the gate roads, resulting in pillar failure near the margin of a fluvial channel. Loads were shown to transfer to a harrier pillar (width height ratio equal to 9), contributing to progressive failure of this pillar. Unloading of the barrier pillar was associated with significant load transfer to the two-seam submains to the north of the harrier, contributing to roof falls, floor heave, and rib spalling within the submains. Stress analysis results addressed pillar peak strength and unloading behavior that was in agreement with the measurements and underground observations. Underground observations and stress analyses were completed before and after longwall mining near a six-entry submain in mine 2. This submain was intended to he used as a temporary bleeder and tailgate for a small longwall block consisting of one to two panels, depending on the development schedule in other areas of the trine and observed ground conditions. Numerical modeling using both elastic and inelastic pillar behavior for submain pillars with a width-to-height ratio of 8 was completed before mining began. Results indicated that pillar unloading was likely. During retreat of the first longwall panel, pillars unloaded. as evidenced by progressive rib spalling along the cleats, This behavior was mostly confined to the immediate face area, an observation that was in agreement with the modeling results,

Jan 1, 2000

By J. K. Owens

As part of a larger research effort focused on ground control, the U.S. Bureau of Mines is currently evaluating the effectiveness of using stereological analysis for characterizing mine roof strata. Input for a stereological analysis of a rock mass is best obtained by scanning (imaging) the walls of clean drill holes using a video-imaging borescope or other video device. Two classes of features are being investigated: (1) Lithologic types that comprise the overall rock mass and (2) structural discontinuities (e.g., joints, foliation, bedding planes) within a given lithologic unit. In the former, the volume fraction of a given Lithologic unit in relation to the entire rock mass can be estimated. In the latter, the mean intercept length between adjacent structures and surface area density of the geologic structures can be estimated. Examples of sampling procedures and subsequent computations are presented for several situations using information collected from drill holes in roofs of underground mines. One such example is based on the trace of a cycloid curve used as a stereological sampling path on the cylindrical wall of a drill hole. Stereological measures, such as intercept length, volume fraction, and surface area density, are explained in the context of rock mass characterization.

Jan 1, 1994

By Rob Robinson

Following a massive rib wall failure along the reclaim belt of the large underground surge bunker at CONSOL?s Bailey Mine, a multifaceted, cleanup and rehabilitation effort was initiated to rapidly stabilize the bunker rib walls and place the bunker back into production. Rehabilitation of the bunker included infilling and re-mining of the failed excavation area, installing a system of horizontal tie-back cable bolts, constructing a large knee wall at the base of the rib, reducing water inflow, and providing drainage for rib water. As a result of the coordinated effort, the bunker was safely placed back into production within 38 days. The 7500-ton surge bunker, an engineering feat in itself, was constructed in 2003 to accommodate production surges from two longwalls. In 2005, 14.8 million raw tons passed through the bunker. The 22-foot wide by 75-foot high surge bunker excavation extends as much a 52 feet below the base of the Pittsburgh seam. The bunker excavation measures 325 feet in length, with feeder and reclaim belt excavations extending the bunker excavation by approximately 500 feet. The massive rib roll, which occurred near the bottom of the reclaim belt slope, measured as much as 45 feet high by 60 feet long. Failure of the rib was attributed to progressive failure of a thick claystone unit present near the slope bottom area. Saturation of the claystone by water inflow, high insitu horizontal stress, and pre-existing rock joints were considered contributing factors. Immediately after rib failure, mine production was temporarily rerouted to a parallel belt. Two bulkheads were then constructed 175 feet apart along the reclaim belt slope, and a customized fly ash-cement mixture was pumped from the surface into the unstable reclaim slope area. A tunnel was then mined through the backfill along the original reclaim slope contour; the new excavation supported by a system of customized steel sets. To assure stability of the adjacent bunker rib wall, a pattern of 70-foot long cable bolts were installed downward from the adjacent entries to effectively tie back the rib. Drainage holes and a 12-foot high knee wall were installed. Adjacent gas wells were also plugged to help reduce inflow. Periodic inspections and continuous monitoring are being used to help assure bunker stability.

Jan 1, 2007

By Michael A. Berdine

In early 1997, Twentymile Coal Company took a dramatic departure from traditional longwall recovery methods. Previously, Twentymile's standard longwall meshing procedure included the use of chain link fencing material. Beginning with the 9-Right to 8-Right longwall recovery operation, Twentymile incorporated a polyester geogrid mesh system supplied by DYWIDAG-Systems International. This paper discusses the subsequent utilization of the polyester geogrid mesh system at Twentymile.

Jan 1, 2001

By Gerald I. Finfinger

Identifying the properties of overlying rocks in underground mining operations is important to ensure the appropriate roof support design is used to maintain stability of the mine entries. Recently J. H. Fletcher & Co. developed a monitoring and control system for roof bolters for the underground mining industry. The system records the drilling parameters used during roof bolt drilling and the information can provide insight into the physical properties of the roof strata. The parameters include thrust, rotational speed, torque and velocity and the measurements are collected every 0.1 second during the operation. The drilling parameters were analyzed to determine the application of identifying the strength of rocks being drilled from the measurements. The data was converted into the specific energy of drilling which is a measure of the amount of energy required for removing a given unit of rock during a drilling operation. The laboratory studies completed to date indicate a fairly high correlation between the specific energy of drilling and the unconfined compressive strength of the rocks that were drilled. Additionally, the drilling parameters were shown to be effective for identifying the presence of fractures or bed separations between rock ]avers. The thrust, torque and specific energy of drilling were all good indicators for identifying the fractures or separations. Regardless of the drilling parameters used during the drilling experiments, the location of the fractures were identified, In order to determine the application of the drilling parameters for identifying rout rock properties, two series of experiments were conducted. The first series of experiments used three "manufactured" roof layers that had various rock samples embedded in concrete blocks. The rock samples included three types of sandstone, marble. and argillite. Another concrete block was poured with foam inserts to simulate large bedding separations (2 to 8-in). Two other manufactured blocks were constructed using high-strength concrete with cardboard layers embedded to simulate smaller fractures or bedding separations. The size of the cardboard layers varied from 1/8- to 1-in thick. One of the blocks had the cardboard layers embedded at an inclined angle to determine the effect of the orientation or, the drilling parameters. A series of experiments was conducted with the rotational speed and the penetration rate held constant and the thrust and torque allowed to vary. The information collected from the experiments is used to determine the application of the drilling parameter measurements for identifying rock properties, fractures and bedding separations.

Jan 1, 2000

By Jian Yong Chen

The results of a laboratory investigation of pullout tests conducted on grouted, plain cable bolts are reported. The main purpose of the study is to determine experimentally the shear bond stiffiess of cement grouted and resin grouted cable bolt systems, which is an important input parameter for numerical modeling of cable bolt support. Three nominal embedment lengths of 152mm (6 inch), 203mm (8 inch) and 254mm (10 inch) were used and two types of grout namely cement and Anchortite resin were used. Two water- to-cement ratios of 0.3 and 0.4 were employed for the cement grout. The concepts of effective shear stress and effective shear stiffiess are explained and adopted to calculate the shear bond strength and the elastic shear bond stiffiess per unit length. A comparison of results with previous research is presented to reveal the effect of water-to-cement ratio and embedment length on the shear bond characteristics of grouted cable bolts.

Jan 1, 2005

By Denise Mueller, Axel Preusse

"In 2010, the fracking discussion in Germany caused a number of changes in German law, which came into force in 2016. Especially the production of gas had to be regulated. With the legislation amendment, the “Subsidence-Area Mining Regulation” (in German: Einwirkungsbereichs-Bergverordnung) has been revised, too. The changes expand the compensation of mining damages, especially to the extraction with drilling from the surface and underground storage. Although the “Subsidence-Area Mining Regulation” has been revised, the area of main influence (subsidence of 10 cm) remains to determine a relevant boundary for mining damages. The determination and prediction of this boundary above caverns are presented in this paper. In addition, further elements of ground movements and their relevance to mine damages are analyzed. The usage of the area of main influence to fix a relevant boundary for mining damages does not correspond to the relevant elements of ground movements. A limit for differences in subsidence (tilt) or horizontal changes in length should be preferred to describe the relevance of mining damages on buildings. Furthermore, this paper outlines the the meaning of using the area of main influence to fix a relevant boundary for mining damages. INTRODUCTION The “Federal Mining Act” (in German: Bundesberggesetz, short: BBergG) forms the central legal standard to cover subsidence in Germany. The mining authority refers to the following regulations (Preuße et al., 2015): the “Subsidence-Area Mining Regulation” (in German: Einwirkungsbergverordnung, short: EinwirkungsBergV; since 1982) the “Mine-Surveyor Mining Regulation” (in German: Markscheider-Bergverordnung; short: MarkschBergV) the “Deep-Drilling Regulation”"

Jan 1, 2017

By Thomas M. Barczak

The initial Support Technology Optimization Program (STOP), Version 1.0, was released at the 19th Gmund Control Conference. This original program has since been updated to Version 2.3 which was released in May, 2001. This paper describes the additional features of Version 2.3, focusing primarily on the following three aspects: (I) including uncontrolled convergence into the design requirements for standing roof supports, (21 the addition of design procedures for cable bolts as an alternative secondary roof support, and (3) the addition of new standing roof support technologies. Another new feature which should facilitate the development of design criteria for standing roof support is the capabilily to define ground reaction curves through convergence measurements alone wthout having to make support loading measurements. There are several other new features provided in Version 2.3 which are only briefly addressed in the paper. These include: (I) additional graphics capabilities to facilitate rapid assessment of support comparisons. (2) an East-West designation for support selection to more accurately provide cost and support availability data, (3) additional safety measures including a safety factor to identify support design near the peak support capacity, checks to see if the support dimensions comply with aspect ratio requirements, and measure of roof coverage for the design layout of the support system These new features of STOP provide more capabilities to design and analyze secondary roof support systems for conditions whlch could not be fully analyzed in the original version of the program.

Jan 1, 2001

By Keith A. Heasley, Jian Yang

"LaModel uses a laminated overburden boundary-element model and can calculate not only seam-level stresses and displacements but also surface subsidence for thin tabular deposit such as coal seams (Heasley, 1998). Up to this point in time, the material property wizards in LaModel have primarily been designed for calculating accurate stress distributions in single- and multipleseam situations, and for investigating and optimizing pillar sizes and layouts in relation to overburden, abutment, and multipleseam stresses. However, the critical input parameters that will give the most accurate seam-level stress distribution do not necessarily produce the best surface subsidence prediction. The objective of this paper is to develop a methodology for calibrating the critical input parameters in LaModel to optimize surface subsidence prediction.For optimum surface subsidence prediction, it was found that the gob convergence (as defined by the final gob modulus) and the overburden stiffness (as defined by the lamination thickness) were the two most critical parameters that needed to be calibrated (Heasley, 2016). By calibrating numerous panels with various widths and depths, a formula that provides the optimum final gob modulus to use for subsidence prediction was developed. Also, three different empirical formulas for optimizing the lamination thickness as a function of overburden depth and/or the panel width to- depth ratio were determined for the three cases: supercritical panels, and subcritical panels with and without offsets. Further, if the user has measured data for subsidence factor and angle-of draw, the optimum final gob modulus and lamination thickness can be determined from the measured data. These new subsidence prediction formulas are being implemented into new material wizards in LaModel.INTRODUCTIONIn the past few decades, with the increased need for highly productive mining techniques, full extraction mining methods have been increasingly employed in the U.S. coal mining industry. These total extraction mining methods, which include both longwall mining and room-and-pillar retreat mining, normally cause immediate roof caving and the associated surface subsidence. These methods can be highly productive and cost-effective, but the associated surface subsidence can cause damage to surface structures and negatively impact the surface environment (Peng, 2008). Therefore, a reliable program for predicting the surface subsidence associated with full extraction mining is required for appropriately engineering and managing the surface subsidence impacts of full extraction mining."

Jan 1, 2016

By Richard A. Allwes

A procedure is presented for the design of an arch canopy for the application of rehabilitating a high-roof-fall area. This procedure is specifically developed for evaluating an unbackfllled arch canopy, which Is subjected to an impact load (roof fall). Dynamic line loading of the arch canopy at its crown is only considered and the procedure does not account for an unsymmetrical loading condition. The evaluation of whether an arch canopy is suitable for a particular installation is dependent upon many variables, including in-nine conditions and the engineering properties of the structure. However, a general evaluation can be based upon a comparison of the arch's maximum crown deflection and a prescribed allowable crown deflection. A single spring-mass system is used as an idealized model to represent the dynamic behavior of the arch canopy at its crown. An energy approach is taken to determine the maximum crown deflection of an arch rather than solving a differential equation of notion derived from dynamic equilibrium. The design procedure is based on the concept that when an arch canopy is subjected to impact loading at its crown and deflects from its unloaded state to maximum crown deflection, the structure absorbs strain energy, both elastic and plastic. As a result, this strain energy can be calculated from a static load-displacement diagram for the structure. The significance of this design procedure Is that It gives mine personnel an analytical tool to select an arch canopy to meet the dimensional and functional requirements of a mine entry and a prescribed allowable crown deflection.

Jan 1, 1986

By G. Skybey

The Skybolt is a new bolt concept, point anchored with resin in large diameter holes of specific sizes 38 mm and 45 mm. The new design achieves the optimum annular spacing required for mixing the resin anchor components which is essential for optimum resin bonding of the bolt to the surrounding rock. This paper explains the load transfer mechanisms between bolt/resin/rock, unique to this bolt concept. It compares the pull-out test results to those of paddle and expansion shell type bolts, and highlights the versatility of Skybolt over existing, currently used, rock support systems and the benefits mine operators can achieve when using the Skybolt.

Jan 1, 1992