Search Documents

By Dennis R. Barratt

Rockbolting is now used extensively as a method of primary support in UK coalmines. Over the past fifteen years an optimum bolting system has evolved, based on a high grade steel bolt and a very strong stiff resin. Where necessary, cablebolts are used in conjunction with rockbolts as a supplementary means of support. The rockbolting system, as currently used, is based on a maximum bolt length of 2.4 m whilst cablebolts are generally 6 or 8 m long. Based on the UK experience, there are situations where it is necessary to extend the bolted horizon above that normally achieved with a 2.4 m long rockbolt. Until recently the only options available were coupled rockbolts or cablebolts, both of which have inherent problems in terms of installation. Flexible Strand Rockbolts (FSR), in lengths of 4 to 6 m, provide the means of being able to extend the normal bolted horizon Other advantages include increased strength characteristics (tensile and shear), able to be installed in the UK standard hole size (26-28 mm), encapsulation using resin capsules, thus offering immediate support, high bond strength compared to conventional strand, and able to be installed using existing drilling and bolting equipment. The FSR is considered to be a new concept in terms of strata control and one that compliments the rockbolting system currently in use.

Jan 1, 1997

By Jamal Rostami, Asok Ray, Samer S. Saab Jr., Wenpeng Liu

Ground instability, such as roof or rib failures, is one of the most serious and frequent safety hazards that occur in underground mining, tunneling, and underground construction. The ground-related parameters and features of interest, in assessing roof or rib failures, are location, frequency, and orientation of the joints, voids, as well as rock-strength. These parameters are the main components of rock mass characterization that offers effective strategies for ground support, which, in turn, allow one to mitigate the risks related to ground instability. The main objective of this study is to determine the location of joints and classify rock-strengths by analyzing the drilling data recorded from an instrumented roof bolter while drilling for rock bolt installation during the operational cycle. For this purpose, computer programs based on updated pattern recognition algorithms were developed for joint-detection and classification of rock types to offer an estimated strength. This paper briefly introduces ongoing research on joint detection, especially for joints with an aperture less than 0.125in (3.175mm), by employing an instrumented roof bolter in controlled environments. To improve the capability and precision of joint detection programs in detecting the joints from the drilling data and reducing the number of false alarms, many laboratory tests with various simulated joints and rock-strengths were carried out at a J.H. Fletcher & Co. facility. This paper reviews testing procedures, data analysis, updated algorithms used for joint detection, and discusses the latest round of testing in samples with simulated joints at various angles along the borehole.

Jan 1, 2017

By Donovan J. Benton

Photogrammetric methods are advancing rapidly and show considerable promise as a ground control research tool. The ability to quickly capture three-dimensional geometry, especially changes in geometry, in underground and laboratory settings is a significant advance from point distance measurements. Photogrammetry is being applied in both of these settings as part of the NIOSH ground control research. This paper describes these applications and the equipment and software being employed. It also describes tests conducted to quantify the accuracy of these systems. Accuracy varied with system specifics and procedures. A factory-calibrated camera produced results within 1/32 of an inch, plus 0.04%. A user-calibrated camera was found to be less accurate, at 1/20 of an inch, plus 0.24%. These calibrations demonstrate that photo grammetry can produce research quality measurements in laboratory and mine settings.

Jan 1, 2014

By Sandin E. Phillipson

"On April 5, 2010 a massive dust-fueled explosion at a longwall mine in southern West Virginia claimed the lives of 29 miners. The mine had experienced large gas inrushes from the floor on two known previous occasions, and natural gas was found emanating from floor fractures behind the longwall shields after the explosion, indicating a likely fuel source for the initial ignition. In succeeding months, another longwall mine operating in the same seam 15 miles away encountered smaller inflows of natural gas that halted production from two different longwall faces. Production was halted at a third longwall mine, 30 miles south of the first, in May 2011, when explosive levels of methane were detected inby the longwall face on the headgate. The same mine was evacuated on March 20, 2014 when a series of floor gas feeders were encountered on the longwall face. A literature review indicated that there has been little documentation or description of these events, and that their size and frequency are unknown. The most significant floor gas inrushes in the United States are believed to have been associated with longwall mining in the Pocahontas No. 3 Seam of western Virginia, in which an estimated 5.8 x 107 ft3 of natural gas was expended from a floor feeder on the longwall face over a two-week period (Aul, pers. comm.).A variety of mechanisms and circumstances are associated with methane emanations from underground mines. Hyman (1987) defined an outburst as a violent, simultaneous release of gas and comminuted rock material into a working face or the interior of a borehole, and indicated that certain soft or fractured coals have a propensity for outburst based on gas desorption rates. In this mechanism, reservoirs of autogenic gas hosted in pockets of soft, crushed coal surrounded by harder coal are released suddenly as confining stress is removed by mining. Hyman (1987) also suggested that highly stressed, relatively gassy coal that is penetrated by mining-induced fractures could be outburst-prone. Clayton et al. (1993) and Ulery (2008) recognized the importance of faults as potential conduits for gas from adjacent strata into coal mines, and suggested that biogenic gas trapped in adjacent strata could migrate into mined coal seams due to a pressure differential. Ulery (2008) distinguished between an outburst and a blower, the latter defined as an event expending a large amount of gas over an extended time period, most often emanating from underlying strata, but without expulsion of coal or rock. Methane feeders are further defined as a subset of blowers that continually expend gas over a long period of time but at a lower rate. Many of the mechanisms discussed by Ulery (2008) relate to geologic features that can impound gas within the seam, releasing a voluminous amount when mining breaches the elastic dike, fault gouge, or other geologic structure that had restricted and compartmentalized coalbed methane migration. Thus, the events discussed in this paper can be described as blowers and feeders. However, detailed geological observations of the three longwall mines discussed in this paper appear to indicate a mechanism that is different from those described by Hyman (1987) or Ulery (2008), in that they did not involve coalbed-sourced gas, and the reservoirs were not hosted by coal seams."

Jan 1, 2016

By Tony Iannacchione

A close look at the Loyalhanna Limestone of southwestern Pennsylvania reveals a complex structural environment. Most exposures of the Loyalhanna occur along Chestnut Ridge and Laurel Hill within the Allegheny Mountain Section of the Appalachian Plateaus Province. Because the Loyalhanna is rated as a super pavement aggregate by the Pennsylvania Department of Transportation and because of its proximity to the population centers of southwestern Pennsylvania, the Loyalhanna has been extensively mined along these prominent anticlinal structures. Geologic and engineering analyses were performed using gas well and core logs, outcrop examinations, underground observations, and mine maps. Strata exposures from both outcrops and quarries were used to construct geologic maps, stereonet, and rose diagram projections so that the Loyalhanna's structural environment could be understood better. Many of these structural conditions cause ground control problems at local quarries. These problems ranged from small-to-moderate sized rock falls associated with roof jointing to pillar failures associated with dipping discontinuities. Stresses ranged from tensional on structural domes where weathering dominates, to high levels of compression within structural saddles. A greater understanding of these characteristics is a prerequisite to develop engineering controls, such as improved mine layouts. pillar sizes, etc., that lessen miner exposure to these hazards.

Jan 1, 2002

By Peter Fischer, Heinz-Jiirgen Kateloe, Anton Sroka, Axel Preusse

"Since mining in Germany has a long history, there are still many locations where the surface fracture problem has to be solved. Shallow mine workings from an earlier era can affect the surface in a discontinuous way. In many cases, due to light overburden load, those mine rooms did not collapse and a downfall can suddenly happen for many reasons, e.g., in connection with a changed load entry into the subsurface or by additional influence of water. This results in ground movements, which in extreme cases, appear as surface fractures.Depending on the use of the surface, ground movements caused in such a way constitute an endangerment by law. Particularly, within the southern Ruhr district, surface fracture and subsidence endangered ranges are determined on the basis of an empirical method that resulted from a systematic evaluation of surface fractures and rock disclosures. This method indicates maximum ranges within which impacts from abandoned shallow mine workings must be assumed.With a special emphasis on a risk management approach, RWTH Aachen University adapted the model of stochastic media to the conditions of abandoned shallow mining to compute and illustrate potential ground movements due to the collapse of shallow mine workings. Further investigations were concerned with the analysis of characteristic parameters which can serve for the assessment of the surface fracture probability in a comparative view of different cases. In recent years, more than 50 surface fractures in the southern Ruhr district were analyzed in order to develop a risk assessment of surface fracture endangered ranges over shallow mine workings. The results that have been obtained so far are described in this paper.INTRODUCTIONAbandoned underground mine workings of shallow depth can pose a threat to the surface. Due to small overburden rock loads, shallow excavations often remain intact for decades after the operations have ceased and may collapse abruptly (Braemer et al., 2005; Hollmann and Nuerenberg, 1972; Preusse et al., 2007). Several approaches for prognosis of surface fracture resulting from 97 subsurface collapse deal with this topic (Loebel and Sroka, 2001; Tajdus and Sroka, 2009)."

Jan 1, 2010

By Wen H. Su

Multiple seam mining and its associated problems are very serious in Southern West Virginia where poor planning or lack of knowledge in seam interaction often results in complete loss of coal properties. Several measures have been proposed to alleviate the interaction prob¬lems under various multiple seam conditions, but few of them are spec¬ific in terms of mining plan. Two parallel approaches are adopted for this paper. One is field investigation which consists mainly of mine site visits and gathering of data. The other is the two-dimensional finite element simulation of mine workings using the data gathered as input. Two typical cases which represent the past and present multi¬ple seam mining practice in West Virginia were investigated. Much attention is focused on the interaction problems experienced and the important parameters controlling interaction. Several key parameters controlling interaction in multiple seam mining were analyzed. Proper mining plans, by which the interaction problems can be minimized, are proposed for the individual cases after a better understanding of the interaction mechanism was realized through finite element analyses.

Jan 1, 1984

By J. Nielen van der Merwe

During the process of pillar extraction at the Welgedacht Colliery, an unexpected pillar collapse resulted in the entrapment of equipment. The area was visited soon after the event to evaluate the stability of the area for the purposes of extracting the equipment. It was found that the area had stabilised sufficiently to allow work without undue risk to the safety of workers. The equipment was reclaimed successfully. A subsequent investigation into the reasons for the collapse was conducted. It entailed detailed underground and surface subsidence observations and numerical modeling. It was found that none of the perceived negative factors that were present at the time could result in pillar loads that were sufficient to cause the collapse. It was concluded that the local pillar strengths were less than the nationally used value and that they were possibly further reduced by aging.

Jan 1, 1999

By G. R. Corbett

Between 1977 and 1984, No. 26 Colliery, at Glace Bay in the Sydney Coalfield, suffered from a series of 37 rock/gas outbursts. These events were characterized by the complete pulverization of a sandstone which was propelled into the mine roadway and an associated release of methane gas. The events began to appear at a depth of 700 m and increased in intensity and damage to the excavation as the mining depth increased. At the time of the closure of No. 26 Colliery (as a result of an unrelated fire), these outbursts were the subject of intensive investigation. Although No. 26 is now closed, there is concern that similar events could appear at Phalen Colliery where current development work is proceeding at a depth close to the 700 m threshold. Past investigations into rock/gas outbursts included studies of in situ stresses, the simulation of outburst events in the laboratory, investigations into the potential for destressing an& degassing of problem sandstone and the development of numerical models to assist in the design of openings in outburst prone ground. However, despite this work, methods of predicting outburst conditions are presently limited to examination of probe hole cores for core discing, and methods of working under such conditions are limited to boring and firing and using volley firing techniques to initiate any outbursts while workers are safely out of the heading. During this investigation of worldwide occurrences of this phenomena, literature obtained suggested that outbursts might generate microseismic precursors. An intrinsically safe (IS) microseismic monitoring system was designed and developed based on CANMET's rockburst monitoring system currently in use in hardrock mines, and installed in a development roadway at the deepest extent of the Phalen Colliery. The system will record microseismic activity associated with development work to try to identify characteristic precursors of outburst-prone conditions. This paper describes the steps taken to identify a microseismic system suitable for use at Phalen colliery, of which part of the requirement was that it be IS and approved for use in the Sydney Coalfield. The modifications to the selected system are described, along with its capabilities and the preliminary results of its performance over the first few months of use.

Jan 1, 1994

By Lewis Dr. Wade

It is really an honor and pleasure to be here at the 231d International Conference on Ground Control in Mining. My name is Lew Wade. Until recently I served as the Associate Director of Mining for NIOSH. That's a position that I recently moved out of and that position is now filled by Dr. Jeffery Kohler. I now serve as the Sr. Science Advisor to the NIOSH Director. The topic of my talk today will be coal mine ground control, a look back at the last 30 years, and then a brief look forward. I will start by talking about coal mine ground control statistics and with just a brief look, those statistics clearly show that you people are making a difference and there have been tremendous improvements. I'll then look at reasons for those improvements and those will include people working together (this conference being a prefect example of that), as well as technology development. In the area of technology development, I will give you my top-ten list of technology developments in the area of coal mine ground control. Then I'll end with a look towards the future and point to some possible future developments. Then, I will be so bold as to issue some challenges to the participants of this conference. Again, if you take the broad look back at underground coal mine roof falls and ground fatalities, you see this tremendous improvement that we have all come to appreciate. We have all been a part of improving the safety conditions for our underground miners and the number of fatalities is orders of magnitude less than what it was at the turn of the previous century. We have every reason to be pleased and proud of what we have been able to accomplish. Now, the question is why. What are the reasons for those improvements? Just look around this room. You see evidence of what I think are one of the principle reasons: miners, mine operators, government workers and researchers, equipment suppliers, people in research and academia working together. Coming together and sharing at a Conference like this over the last 23 years.

Jan 1, 2005

By Yun Zhang, Haijun Jiang, Shenggen Cao, Chen Wang

The distribution of front abutment pressure is closely related to the force, deformation and energy distribution of hard roof before periodic weighting. So it is necessary to carry out research on the relationship between them. According to front abutment pressure distribution feature, using the location of peak front abutment pressure as the dividing point, coal seam is divided into two parts along the direction of mining: the yield zone that is the area between the faceline and the point where the maximum front abutment pressure occurs, and the elastic zone that is the part before the point of peak front abutment pressure. The proposed mechanical model of unit width hard roof at the panel center periodic weighting consists of five parts including the yield zone. All parameters of the deflection equations for each of the five parts that satisfy the continuity conditions and natural boundary conditions are obtained by using the Matlab software. The continuous curves of front abutment pressure, deflection, bending moment and bending strain energy density distribution of hard roof are obtained by iterative approximation method. The following conclusions can be drawn through analyzing those curves: (1) The position of peak front abutment pressure is located at the transition of coal seam foundation from yield zone to elastic zone (elastoyield critical point), the distance of it to the faceline is equal to the width of yield zone. The peak front abutment pressure increases with yield zone with. (2) The peak bending moment in front of the faceline, and the distance of it to the faceline increase with the yield zone width. The deflection of hard roof at the face and midspan also increase with yield zone width. (3) As the yield zone width increases, the accumulated elastic energy of hard roof in front of the faceline increases, and the core zone of energy moves forward away from the face. (4) When the yield zone width is zero, the whole coal foundation is regarded as elastic foundation, and the peak front abutment pressure occurs at the faceline.

Jan 1, 2015

By K. Biswas

So far, all pillar design methods or approaches consider the coal seam as a uniform structure From some mine visits in northern Appalachian Region. it is found that some coal seams have binder or parting material within the coal scan with varying thicknesses and numbers- And it has also been found that these kinds of hinder materials tire prone to weathering when exposed to ambient mine moisture In this paper an attempt has been made to study the weathering susceptibility of parting materials and coal when exposed to moisture and a two dimensional finite element analysis has been carried out to study the effect of the presence of partings on the structural integrity of the coal pillar in terms of short-term and long-term stability.

Jan 1, 1995

By Sandin Phillipson

During the course of ground control evaluations conducted by the Mine Safety and Health Administration's Roof Control Division, a number of surface and underground coal mines were visited that exhibited instances of ground failure associated with joints. The evaluations were conducted over a broad geographic area, including the Appalachian Basin from Pennsylvania to Tennessee, and they documented that joints occur in a wide variety of mining conditions and exhibit a wide variety of characteristics. Despite minor local variability in orientations, the joints fit into a cohesive pattern when evaluated on a regional scale in context with the system of thrust faults that define the Alleghany Front. Joints documented for this study, together with joints in sandstone and coal and the trends of drag folds compiled from other studies, were plotted on regional maps using GIS software. The trends of joints, including those that could be described colloquially as "hill seams," were not only parallel to regional fault systems and local trends of drag folds, but were also parallel to the regional patterns of previously mapped joints in sandstone and coal. These observations indicate that the features referred to informally as "hill seams" are in fact joints formed in response to tectonic processes associated with regional deformation of the Cumberland-Allegheny Plateau. The 286-266 million-year-old age of regional deformation significantly pre-dates the time when the Cumberland-Allegheny Plateau was subjected to deeply incised stream valley erosion, which began 25 million years ago. This challenges an existing interpretation that "hill seams" represent local ·stress relief joints that formed when stream valley erosion removed confinement and allowed tensile failure of the rock. Although relaxation of confining stress can reasonably be expected to occur near outcrop, observations indicate that this results in the dilation of existing joints. This paper presents instances of ground failure associated with joints, discusses methods of mitigation, and recommends that the term "hill seam" be abandoned in technical communication because it simply refers to a kind of joint that may exhibit certain weathering and aperture characteristics.

Jan 1, 2010

By Freddie Hunter

An underground mining method for extracting an eight metre (26') coal horizon, containing a sandstone layer. A decrease in the thickness of the rock strata between the number two and number three seams of the Sasolburg Coal Field, has resulted in a total mining horizon approximately eight metres (26') thick. This parting varies in thickness and competency and in some areas is impractical to cut with a continuous miner. In addition, the general mining area is highly jointed. The top seam is first mined to a normal bord and pillar plan with a continuous miner. The bottom seam is then mined by selectively undercutting the stone parting constituting the floor of the top seam. In areas where this parting is between 0.75 - 2.50 metres (29.5" - 98") thick, it is suspended from the primary roof support installed when mining the top seam. Secondary, high extraction retreat mining is then undertaken in the coal pillars adjacent to the suspension supported headings in the bottom seam. Left in-situ, the parting provides lateral support to the pillar sidewalls in both the top and bottom seams, enabling high percentage extraction rates in what was previously thought an uneconomically mineable area. The paper proposed, presents the challenges and practical implications of executing the mining method, including the primary roof control of the top seam and the stone parting between scams.

Jan 1, 2003

By Ashok Kumar, Rajendra Singh, Petr Waclawik

High-grade coal is locked in the shaft protective pillars at 900 m below surface in the Czech part of Upper Silesian Coal Basin. To optimise recovery of coal from the larger size shaft protective pillar, room and pillar (called bord and pillar in India) is trialled to further develop these on smaller pillars. This development followed a constant gallery width of 5.2 m and 3.5 m height. The monitored pillar size in the first developed panel varied from 860 m2 to 1225 m2 of area. The stability of these pillars (i.e., natural supports) at this depth of cover is observed to be a vital issue to control ground movement and safety of the surface structures. A simple calculation of safety factor revealed that application of an empirical method for estimating size and shape of the pillar is inappropriate due to complex geo-mining conditions of the site. Accordingly, geo-technical instruments are installed in the panel for monitoring the stability of the diamond shaped pillar at different stages of the development. Extensive monitoring of the pillar behaviour by these instruments provided an important set of data for such optimum recovery. An established process of simulation-based pillar strength estimation is often used by the mining industry, but calibration is generally done with the help of empirical formulation. However, for the deep-seated pillar, the strength suggested by the existing empirical formulations (except the CMRI formula) is found to be much different from the instrument observations. Using a study conducted at Czech hard coal mines, an attempt is made to develop a strain-softening-based numerical modelling approach to assess pillar performance at deeper cover. The recorded value and nature of the pillar spalling in the field along with the CMRI formula are used to calibrate the developed simulation approach. An assessment of the stability of the developed pillars using simulated models did not indicate any collapse of the natural supports. This paper briefly presents difficulties in pillar design at great depth of cover and field and simulation results of pillar strength estimation in Czech hard coal mines.

Jan 1, 2018

By Robert B. Francini

Longwall mining and pipelines have coexisted since longwall mining was introduced into the United States. How the pipeline operator reacts to longwall mining under their line depends on many factors. This paper outlines the process the pipeline operator goes through to determine the appropriate response when their pipeline is being undermined. Typical mitigation procedures are reviewed. Finally, the paper looks at current design practices for new pipelines that are expected to be undermined during their lifetime.

Jan 1, 2011

By Tulu B. Ihsan, Mark A. Van Dyke, Ted M. Klemetti

"How well do current modeling procedures calculate the rear abutment extent and loading? Does an improved understanding of the rear abutment extent warrant a change in standing support in bleeder entries? What is the optimal standing support for bleeder entries separated from the longwall startup room by a barrier pillar? To help answer these questions and to determine the current utilization of standing support in bleeder entries, four bleeder entries at varying distances from the startup room were instrumented, observed, and numerically modeled. This evaluation was intended to determine the rear abutment extent and magnitude at various locations to optimize standing support in these entries and those under similar conditions. This paper details observations made by NIOSH researchers in the bleeder entries of a deep cover longwall panel; specifically data collected from instrumented pumpable cribs, observations of the conditions of the entries, and numerical modeling of the bleeder entries during longwall extraction. The primary focus was on the extent and magnitude of the abutment loading experienced by the standing support. As expected, the instrumentation of the standing supports showed very little loading relative to the capacity of the standing supports—less than 25 tons load and 1 inch convergence. The observations of the conditions showed little to no change from before the longwall panel extraction began to when the panel was more than 50% extracted. In addition to the observation and instrumentation, numerical modeling was performed to evaluate the bleeder design. The Flac3D program was used to evaluate these four bleeder entries using previously defined modeling and input parameter estimation procedures. The results indicated only a minor increase in load during the extraction of the longwall panel. The model showed a much greater increase in stress due to the development of the gateroad and bleeder entries, with about 80% of the increase associated with development and 20% with longwall extraction. The Flac3D model showed very good correlation between expected gateroad loading during panel extraction and those expected based on previous studies. The front and side abutment extent modeled was very similar to observations from this and previous panels with similar conditions. The results of this study showed that the rear abutment stress experienced by this bleeder entry design was minimal. The convergence measured in these bleeder entries was small enough not to mandate any additional support beyond development even by U.S. or Australian standards. The pumpable crib load and convergence experienced depends on the geological setting, mining geometries, and timing. The farther away from the startup room, the lower the applied load and smaller the convergence in the entry if all else is held constant. Finally, the numerical modeling method used in this study was capable of replicating the expected and measured results near seam."

Jan 1, 2017

By Marc Arl

Failures of the face and roof above longwall shields have caused days and sometimes weeks of lost production. A common recovery method for these failures has been to pump light weight cementitious grout into the roof and face cavity to stabilize the area This approach while effective is very time consuming and costly. Mines in several coal producing nations have over the past few years been applying phenolic foam grouts in these situations in lieu of cementitious materials. Phenolic foam is a two-component injection product intended for cavity filling, air and gas sealing and the consolidation of highly fractured strata. The properties of phenolic foam; rapid application, quick setting, high expansion rate, high compressive strength and excellent anti-static properties, produce a fast, safe and cost effective cavity filing solution. The product is also classified as fire resistant and so is also suitable for sealing off underground heatings and for aiding fire fighting operations in deep mines. This paper will discuss the application and use of phenolic foam in various underground coal mines in the world over the past few years.

Jan 1, 2005

By Essie Esterhuizen, John Ellenberger, Dennis Dolinar

"Underground stone mines in the United States use the room-and- pillar method of mining. The stability of the roof between pillars determines the mining dimensions and size of equipment that can be used. The findings of a survey of roof span stability issues and design practices are presented, and the observed factors contributing to roof instability are discussed. Identified stability issues are evaluated, such as maximum roof span, horizontal stress, and roof beam stability. The results of field observations, roof monitoring, and numerical analyses are used in the evaluation. The importance of the first roof beam thickness and its impact on roof stability and support requirements is presented. An evaluation of the current experience with stone mine roof spans relative to international experience is presented. A step-by-step design procedure is suggested which emphazises the need to collect adequate geotechnical data, understand the immediate roof stability, select a mining direction, and meet support requirements.INTRODUCTIONIn room-and-pillar mines, the roof between the pillars is required to remain stable during mining operations for haulage as well as access to the working areas. Roof and rib falls account for about 15% of all reportable injuries in underground stone mines (Mine Safety and Health Administration, 2009). Therefore, the stability of the roof is an important safety consideration. The size of the rooms in underground stone mines is largely dictated by the size of the mining equipment. Large mining equipment is used, requiring openings that are on average 13.5 m (44 ft) wide by approximately 7.5 m (25 ft) high to operate effectively (Esterhuizen et al., 2007). The dimensions of the roof spans are largely predetermined by the equipment requirements, and design is focused on optimizing stability under the prevailing rock conditions. If the rock mass conditions are such that the desired stable spans cannot be achieved cost effectively, it is unlikely that underground mining will proceed. In addition, large roof falls can extend across the full width of a room and may extend more than 5 m (16 ft) above the roof line. These large falls are a safety hazard and can have a significant impact on mine access and production. The National Institute for Occupational Safety and Health (NIOSH) research into stone mine roof stability has focused on identifying both the causes of roof instability and techniques to optimize stability through design."

Jan 1, 2010

By Jonathan Duncan, Tim Burgess, William Kendall, Jens Lange

"Steel wire mesh is the accepted standard for roof and rib skin control at most coal mines in the United States. Wire mesh is delivered to the mine in bundles that are heavy and awkward to handle. The large size, stiffness, and weight of the wire mesh can present a safety hazard in transporting underground and storing on the roof bolter. Installing wire mesh on the roof and ribs with the roof bolter can be a challenge as well.Synthetic mesh is lighter than wire mesh and can be folded and rolled into a safe, manageable size. A single synthetic mesh roll large enough to cover the roof and ribs in a deep cut can be safely handled by two men. The roof bolter is designed to carry and dispense the roll as it advances and installs primary roof support, resulting in a single pass roof and rib ground control solution. This paper focuses on the design and implementation of the roof bolter synthetic mesh handling system developed by J. H. Fletcher & Co., Huesker, Inc., and Oxbow Mining.INTRODUCTIONRoof and rib skin control in some coal mines has been an issue since mining first began. Roof and rib skin problems vary from mine to mine. The type of roof rock material exposed after mining; the mine atmosphere; and stresses from depth of cover, over mining, and/or undermining are some of the variables that can contribute to roof skin problems from mine to mine.Potential roof and rib skin problems can be time dependent as well. Some mines have roof skin rock, sometimes called draw rock, that falls when drilling the hole for the roof bolt as the initial roof support is installed. Some roof skins are more stable but can fail over time. The failure of roof skin can even be between properly installed roof bolts with roof plates (Figure 1).Mines have most commonly used a wire mesh that comes in individual panels anywhere from 5 ft x 5 ft (1.5 m x 1.5 m) all the way up to 5 ft x 16 ft (1.5 m x 4.9 m) in size. They are typically constructed of 8- or 9-gauge wire welded on a 4 in (102 mm) square pattern. A 5 ft x 16 ft (1.5 m x 4.9 m) panel weighs approximately 35 lbs (16 kg). These steel wire mesh panels can make it a difficult and sometimes dangerous task to deliver them from the surface to the roof bolter and then store on the machine. Manipulating the mesh panels from the storage area on the machine to the final installation position on the roof or rib can also be a daunting task (Figure 2)."

Jan 1, 2010