Search Documents

By Ihsan Berk Tulu, Mark Van Dyke, Ted Klemetti, Deniz Tuncay

"Longwall abutment loads are influenced by several factors, including depth of cover, pillar sizes, panel dimensions, geological setting, mining height, proximity to gob, intersection type, and size of the gob. How does proximity to the gob affect pillar loading and entry condition? Does the gob influence depend on whether the abutment load is a forward, side, or rear loading? Do non-typical bleeder entry systems follow the traditional front and side abutment loading and extent concepts? If not, will an improved understanding of the combined abutment extent warrant a change in pillar design or standing support in bleeder entries?This paper details observations made in the non-typical bleeder entries of a moderate depth longwall panel; specifically, it explores data collected from borehole pressure cells and roof extensometers, observations of the conditions of the entries, and numerical modeling of the bleeder entries during longwall extraction. The primary focus was the extent and magnitude of the abutment loading experienced due to the extraction of the longwall panels. Due to the layout of the longwall panels and bleeder entries, the borehole pressure cells (BPCs) and roof extensometers did not show much change due to the advancing of the first longwall. However, they did show a noticeable increase due to the second longwall advancement, a maximum of about 4 MPa of pressure increase and 5 mm of roof deformation. The observations of the conditions showed little to no change from before the first longwall panel extraction began to when the second longwall panel had been advanced more than 915 meters. Localized pillar spalling was observed on the corners of the pillars closest to the longwall gob as was an increase in water in the entries. In addition to the observations and instrumentation, numerical modeling was performed to validate modeling procedures against the monitoring results and evaluate the bleeder design. ITASCA Consulting Group’s FLAC3D numerical modeling software was used to evaluate the bleeder entries. The results of the models indicated only a minor increase in load during the extraction of the longwall panels. These models showed a much greater increase in stress due to the development of the gateroad and bleeder entries—about 80% development and 20% longwall extraction. The FLAC3D model showed very good correlation between modeled and expected gateroad loading during panel extraction. The front and side abutment extent modeled was very similar to observations from this and previous panels."

Jan 1, 2019

By Malcolm Ross

The Reserve Mining Co., in the processing of taconite iron ore quarried from the Peter Mitchell Pit, deposited the finely crushed waste rock into Lake Superior near Silver Bay Minnesota. In the early 1970s The U.S. Environmental Protection agency filed a lawsuit against Reserve Mining Co., asking the court to force the company to stop dumping into the lake. On April 20, 1974, after a lengthy court battle, the U.S. District Court concluded that the Reserve Mining discharge into Lake Superior violated federal and state pollution laws and thus ordered Reserve Mining Co., to halt the lake disposal of taconite tailings. At the time many feared that some of the mineral particles contained in the tailings (alleged to be asbestos or asbestos-like) would cause human health problems. This Conference was thus convened to readdress the problem of the mineral content of the Biwabik Iron Formation and to whether any minerals contained in the ore could cause human disease. The four papers given in this session address the nature of the mineral particles in the taconite rock, the definition of the term ??asbestos?? and the history of the legal controversy over the possible health effects of certain mineral particles contained in the Biwabik iron range ores. Paper 1?Geology of the Biwabik Iron Formation and Duluth Complex Mark A. Jirsa, James D. Miller, Jr., G.B. Morey The Biwabik Iron Formation was a principal source of ore for the American steel industry during the 20th Century. The unaltered iron deposits, called taconite, contain approximately 30% iron and 50% SiO2. About 75% of the iron in taconite resides in the mineral magnetite, the remainder is largely in iron carbonate and several iron-silicate minerals.

Jan 1, 2007

By Joe Roby

Rolling disc cutters are the business end of hard-rock and mixed-face tunnel boring machines (TBMs). Since their first successful employment on a TBM more than 50 years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates are higher and cutter costs are lower than ever before, proving the value of investment in cutter development. Disc cutters are used on a range of tunneling equipment, from pipe jacked slurry micro-TBMs less than 1 m (3.3 ft) in diameter to 15 m (49 ft) in diameter, hard-rock boring TBMs. The geological conditions under which they are employed range from sands and gravels, with several bar of water pressure, to extremely hard, massive rock with UCS up to 420 MPa. Regardless of the type of machine or geology, one thing remains constant: changing worn out cutters is costly. When cutters must be changed in the middle of a tunnel, the contractor incurs the cost of downtime as well as the cost of refurbishing or replacing the cutters. In the case of catastrophic cutter failures, the project can be stopped completely for long periods, and the costs mount up rapidly while tunnel production is at a stand still. Catastrophic cutter failures include the occasion when hard-rock disc cutters are failed in groups (called a ?wipeout? phenomenon) and the operator fails to stop the machine, which results in severe damage to the cutterhead. The cause of this can be either an undetected failed cutter propagating damage to surrounding cutters or operator error in steering. Regardless of the cause, the resulting damage can take days or even weeks to repair. When cutters fail prematurely on EPB or slurry machines in certain geological conditions, it is impossible to evacuate the chamber and, therefore, impossible to get [ ] into the chamber to change the cutters. The solution is frequently an unplanned intervention shaft that must be sunk at great cost. The importance of being able to predict cutter life accurately, and in all geological conditions, cannot be overemphasized. For these reasons, cutters have been developed for specific machine types and sizes, as well as for specific geological operating conditions. Different size cutters are required for different size machines. For example, while 483- and 508-mm (19- and 20-in.) cutters are used on large diameter TBMs, it is impossible to employ cutters so large on a small micro-TBM. Also, the cutter must be designed for the specific geological conditions under which it will be operating. The disc cutter rings required to bore extremely hard rock are the most expensive of cutter rings. However, they provide little advantage in weaker rock formations where less expensive rings will do the job as well. It is important to choose the correct cutter for the machine and the geological conditions in order to get the best balance of cost and risk.

Jan 1, 2009

By Paul D. Klipfel

Introduction Mineral exploration interest, principally for gold, in the south-western Pacific has surged to new proportions. This is primarily due to the application of epithermal exploration concepts in the Australian-Oceana region. Other factors that have contributed to the high level of exploration interest include governmental policies supportive of mineral exploration, along with relative ease of tenure access and a relatively short bureaucratic process. This paper highlights exploration and development activities in the North Island of New Zealand, Fiji, Vanuatu, the Solomon Islands, and Papua New Guinea (Fig. 1). It provides a framework to understand the overall recent enthusiasm that has been brought to the south Pacific by explorationists. Through these recent developments, it is clear that the south Pacific region will become a significant gold producing area and thereby worthy of attention and study. Papua New Guinea alone is the free world's seventh largest producer (Table 1). And, with the addition of production from deposits presently being developed, this status is likely to be raised. History Gold was first noted on various Pacific islands in the late 1500s by Spanish explorers. They thought they had reached the legendary King Solomon mines. Since then, the history of prospecting in the southwest Pacific has coincided with the colonization of the region. Settlers in New Zealand extensively mined alluvial and lode gold deposits starting in the 1850s. The spread of European colonization to the more remote Pacific islands from 1880-1940 was accompanied by varying degrees of prospecting activity by planters, traders, and settlers. Some were successful, others may have been successful, but never returned due to hostile indigenous peoples or disease. In general, records of such prospecting activity are meager and exploration leads are, in some cases, gained through local village folk memory. Most early discoveries were alluvial finds. These led to placer operations, particularly in New Zealand, the Solomon Islands, and Papua New Guinea. Continued prospecting located lode deposits such as the Morobe Gold-field of Papua New Guinea, the Coromandel Peninsula of New Zealand, and the Emperor of Fiji. Some areas were prospected thoroughly. Yet others, such as Vanuatu, remained relatively unexplored until the present exploration surge began. During World War II, interest in minerals was diverted. It was renewed significantly until the middle 1960s and early 1970s when regional porphyry copper exploration was conducted.

Jan 10, 1987

By Raymond W. Henn

The 30th annual short course ?Grouting Fundamentals and Current Practice? was held at the Colorado School of Mines, June 22-26, 2009. The field demonstration portion of the course was conducted June 25, at Hayward Baker, Inc.?s yard in Broomfield, CO. The full-scale field demonstration annually presents many different types of drilling equipment being operated as well as various grouting methods being performed under different field conditions. As part of the field demonstration, the class is shown the proportioning, mixing, testing and injection of various cement grout mixes into sand columns under controlled and measured conditions. These sand column demonstrations have been conducted under controlled and measured conditions each year since 1999 as part of the short course. The sand column demonstrations were conducted prior to 1999, but with less quality control and minimal record keeping of the proportioning, mixing, testing, injection pressures and the final permeation results. The goal of the sand column demonstration is to show the students the effect of the water cement ratio and the use of admixture as well as the fineness of the cement, portland versus ultrafine, used has on the engineering properties of the grout and the grout?s vertical permeation through the sand. Test results for the demonstrations conducted in 1999 and for two separate demonstrations, one at the grout course and one at Geo Denver, conducted in 2000 were published in the 2001 proceedings of the Rapid Excavation and Tunneling Conference (RETC) (Henn et al. 2001). The test results for the 2002 and the 2003 demonstrations were published in the 2005 proceeding of the RETC (Henn et al. 2005).

Jan 1, 2009

By J. H. Zietsman

Ilmenite smelting furnaces must be operated with a freeze lining of frozen slag to protect sidewall refractories from chemical attack by liquid slag. The process has two main control objectives: Firstly the slag TiO2 content must be controlled according to specification, and secondly a safe freeze lining thickness must be maintained. This text only concerns itself with the second objective. Freeze lining thickness cannot be measured directly due to conditions inside the furnace. It is therefore inferred from signals of thermocouples installed into the furnace sidewall. These signals are used as the 'controlled variables' in the freeze lining thickness control loop. The dynamic characteristics of these signals are the focus of this text. During this study a model of the process was constructed to study interactions between the slag bath and the freeze lining. This model was used to conduct simulation-type experiments to study the influence of various parameters (temperature, slag composition, ilmenite feed rate, reductant feed rate, power input, etc.) on the slag bath, freeze lining, metal bath, furnace wall and other parts of the process. In the case of the furnace wall, the modelling results were first plotted in the form of time-dependent isotherms. The dynamic thermal behavior of the furnace wall became evident from these results. To illustrate the dynamics of sidewall thermocouple signals, the results were also plotted as time lags between events occurring in the slag bath, and the time when a thermocouple registered a temperature change. The events studied included sudden changes in slag bath state (composition and temperature), changes in operating setpoints (ilmenite feed rate, reductant feed rate, power input), and operational errors (complete loss of reductant or of all feed). All of the result sets showed significant lags between occurrences in the slag bath and temperature changes in the refractory wall. The delays are such that it appears impractical to rely on sidewall thermocouple signals for warning of impending damage to the refractory wall, or for purposes of actively controlling freeze lining thickness. Some measures are suggested to improve the usefulness of these signals during furnace operation.

Jan 1, 2005

By Geoffrey Fosbrook, Donald Phillips, Anil Parikh

The Second Avenue Subway is a $16.8 billion project planned by the Metropolitan Transportation Authority (MTA) in New York City. It will reduce overcrowding and delays on the Lexington Avenue Line, improving travel for both city and suburban commuters, and improving access to mass transit for residents of the East Side of Manhattan. The project is a new, two-track, 13.5 km (8.5 mile) subway extending from Lexington Avenue at 125th Street in Harlem on the north end of Manhattan, to Water Street at Hanover Square in Lower Manhattan. The first phase of construction includes rock tunnels from 92nd Street to 62nd Street and connection to the existing 63rd Street station, three new stations, and track and systems from 105th Street to 63rd Street, allowing service between 96th Street and Brooklyn via an existing Broadway Line. The following describes the Project in detail, discusses the construction challenges addressed in the design, and the initial design/build contract to be awarded in 2005. A discussion of the planned mined construction of two rock caverns and a cut-and-cover station construction are also included.

Jan 1, 2005

By John Chadwick

In the drive for faster development advance rates, railbound systems can be advantageous, in the right application. Skanska BS, the contractor to mine-owner VSK Mining, is driving an adit access deep into the Volouské Urchy Mountain in Slovakia to access the Gemerská Poloma talc deposit, some 70 km (43 miles) west of Ko?ice, the economic and cultural center of eastern Slovakia. Skanska began driving the Stolna Elisabeth drift in February 2007, extending 25 kg/m (50 lb/yd) rails (with 750 mm or 30 in. between sleepers) into the mountain to provide the main haulage to bring talc ore and waste out of the new mine once it gets into production. It will also be used for personnel transport, and is now almost complete. As a second egress and for ventilation, a 2.5-m- (8.2-ft-) diameter shaft of about 300-m (984-ft) depth will be sunk from surface down into the orebody. Stolna Elisabeth is a 4.2-km- (2.6-mile-) long drift mined at a cross section of some 11 m2 (118 sq ft). The finished profile is 3.2-m- (10.5-ft-) wide by 3.6-m- (11.8-ft-) high. It has been developed on a very slight incline so that water runs down it to the portal. The portal is 450 m (1,476 ft) above sea level and the end of the tunnel is 475 m (1,558 ft) above sea level. Much of the rock through which it has been developed is magnesite with a compressive strength of 150 MPA. The drilling jumbo is an Atlas Copco twin-boom Boomer 282 Raildrill drilling 42- to 45-mm- (1.6- to 1.7-in.-) diameter holes to a maximum length of 2.5 m (8.2 ft), depending on ground conditions. This is a drill jumbo that Skanska has used successfully on a number of projects during its life. The condition of the rock through which this drift has been driven is extremely variable. Five classifications of A1 and A2 and B1, B2 and [ ] B3, where A1 is the most competent rock and B3 is the worst, have been established. The amount of support used, of which more later is determined by the classification of ground conditions. At the time of the author?s visit, the project it was about 40 days ahead of schedule, thanks to high advance rates. For instance 6 m/day (20 ft/d) was the plan for the advance to be achieved in B1 rock, but sometimes the crews have achieved 8 m/day (26 ft/d) ? which is the average for the whole project ? in those conditions. In A1 the best advance rate achieved is 12 m/day (39 ft/d). The loading unit is a Häggloader 9HR-B on crawler tracks with a pony track to run on the rails. This allows the unit to be towed up and down the drift along the rails. To load from the face, the Häggloader lowers the foot of its onboard conveyor system to the floor and the backhoe pushes material on to it. This digging arm-conveyor combination produces uninterrupted, optimal volume loading of the haulage unit, without spill ? a technique offering load capacities as high as 180 m3/h (6,356 cu ft/hour). Further-more, as an electrically powered machine, it offers great

Jan 1, 2009

By Peter L. McSwiggen

The mineralogy of the Biwabik Iron Formation changes dramatically from west to east as the formation nears the basal contact of the Duluth Complex. This reflects a contact metamorphism that took place with the emplacement of the igneous Duluth Complex at tem¬peratures as high as 1200 °C. However, the mineralogy of the Biwabik Iron Formation also varies vertically through the stratigraphy of the unit. This variability in both the vertical and horizontal dimensions makes it difficult to predict exact horizons where specific minerals will occur. The iron-formation has been subdivided into four broad stratigraphic units (lower cherty, lower slaty, upper cherty, and upper slaty) and into four lateral mineralogical zones (1-4). Zone 1, the westernmost zone, is characterized by quartz, magnetite, hematite, carbonates, talc, chamosite, greenalite, minnesotaite, and stilpnomelane. The silicate mineralogy in Zone 2 of the Biwabik Iron Forma¬tion changes very little. However, the minerals begin to change dramatically in Zone 3. Most significantly, Zone 3 is characterized by the appearance of grunerite in both a tabular form and a fibrous form. In Zone 4, the original silicate minerals have completely reacted, and a new suite of minerals occupies the iron-formation. These include grunerite, hornblende, hedenbergite, ferrohypersthene (ferrosilite), and fayalite.

Jan 1, 2007

By Peter L. McSwiggen

The mineralogy of the Biwabik Iron Formation changes dramatically from west to east as the formation nears the basal contact of the Duluth Complex. This reflects a contact metamorphism that took place with the emplacement of the igneous Duluth Complex at temperatures as high as 1200 °C. However, the mineralogy of the Biwabik Iron Formation also varies vertically through the stratigraphy of the unit. This variability in both the vertical and horizontal dimensions makes it difficult to predict exact horizons where specific minerals will occur. The iron-formation has been subdivided into four broad stratigraphic units (lower cherty, lower slaty, upper cherty, and upper slaty) and into four lateral mineralogical zones (1-4). Zone 1, the westernmost zone, is characterized by quartz, magnetite, hematite, carbonates, talc, chamosite, greenalite, minnesotaite, and stilpnomelane. The silicate mineralogy in Zone 2 of the Biwabik Iron Formation changes very little. However, the minerals begin to change dramatically in Zone 3. Most significantly, Zone 3 is characterized by the appearance of grunerite in both a tabular form and a fibrous form. In Zone 4, the original silicate minerals have completely reacted, and a new suite of minerals occupies the iron-formation. These include grunerite, hornblende, hedenbergite, ferrohypersthene (ferrosilite), and fayalite. © 2007 Elsevier Inc. All rights reserved. Keywords: Biwabik Iron Formation; Duluth Complex; Mineralogy

Jan 1, 2007

Extending an organization?s knowledge base throughout the entire enterprise can improve operations. Until recently, though, field operations were often left out of the information loop, as extending high-bandwidth communications into harsh environments often proved impossible due to thermal extremes, physical hazards and caustic chemicals. However, advances in the design and manufacture of rugged fiberoptic cables have now enabled the successful installation of 10-gigabit transmission links to places such as mining operations. The experience of Consol Energy exemplifies how plant managers can successfully enlist ruggedized tight buffered cables to help carry the efficiency of ERP communications into even the most challenging work environments. ?As part of our ERP implementation, we extended our corporate network underground into our mines using fi beroptic cable,? said Tom Prokop, manager-site support for Consol Energy. ?We?ve actually had rooffalls bury the cable between rocks and still did not lose data communications. Our maintenance personnel are now able to access our ERP system while underground at locations that can be up to 32 km (20 miles) away from their desks or the warehouse. Access to the corporate network allows them to order parts, look at electronic schematics, access monitoring data, no matter where they are in the mine. With a few hundred workers below ground, this immediate access translates into a time-savings that adds up in a hurry.?

Jan 1, 2009

By James W. Marold

Tunnel and shaft plugs have been designed to assist in construction of new and rehabilitation of existing tunnels and shafts. Tunnel plugs have been used to provide construction access for side by side tunnels, separation of raw and treated water, and to allow operation of one tunnel during construction of a nearby tunnel. Shaft plugs have been used to seal up surface openings to tunnels and to prevent seepage of water to the surface through adjacent tunnels or shafts. The design construction details of tunnel and shaft plugs are provided. Typical examples of tunnel and shaft plugs are provided.

Jan 1, 2008

By Jim Baumann

Deposited millions of years ago in irregular paleokarstic channels, Jamaica’s extensive bauxite deposits provide good quality ore for alumina production and subsequent aluminum smelting. Bauxite mining operations are critical to the Jamaican economy. It accounts for a large percentage of Jamaica’s export earnings. Bauxite production in Jamaica accounts for about 10% of the world’s output each year. Bauxite deposits in Jamaica lie close to the surface. They can be extracted using standard surface mining techniques. The deposits occur in scattered pockets across the country’s rugged landscape. So it was necessary for two of the country’s major mining and refining operations to implement cost effective methods for the acquisition and management of bauxite reserves and surface ownership distribution rights.

Jan 1, 2002

By S. Jennings

The Red Dog zinc-lead-silver deposit is located in the DeLong Mountains of the western Brooks Range in northwest Alaska. The region is located 145 km(90 miles) north of the village of Kotzebue (Fig. 1).Red Dog’s current resource base is 143 Mt (157 million st) averaging 16.1% zinc, 4.3% lead and 83g/t (2.4 oz/st) silver. It is contained in four structurally separate deposits— the Hilltop, Main Deposit, Aqqaluk and the newly discovered Paalaaq deposit. Recent exploration for the Aqqaluk and the Paalaaq deposits has contributed to Cominco American’s understanding of the detailed structural geology of the district and its role in the placement of individual ore bodies.

Jan 1, 1999

By Steve Kral

Borates are minerals that contain boron. Trace amounts exist in rocks, soil, water and people. Boron-containing ores are rare and U.S. Borax, a subsidiary of Rio Tinto Borax, controls one of the world’s two world-class borate deposits. Through its global systems of mines, refineries, ports, sales offices and distribution centers, the company supplies nearly 45 percent of the world’s demand for borates. Borax has been mining borates in California for more than a century. This year the company celebrated 131 years of continuous business in the Golden State and 76 years at its operations in Boron, the site of California’s largest openpit mine. It also has mines and refineries in Argentina, refineries and ship-ping facilities in Europe and technical staff in the United States, North and South America, Europe and Asia Pacific. So, with the 130±years of borate mining and processing experience behind it as well as its global marketing and distribution centers, there is very little that Borax does not know about borates.

Jan 1, 2003

By Wayne Green

The Regional Municipality of York, located north of the City of Toronto in Ontario, Canada, has experienced unprecedented growth during the past decade, with new home construction averaging 15,000 units per year. This rate of growth is planned to continue well into the future with a projected growth of more than 500,000 new residents by 2031, combined with a tar-get of more than 300,000 new jobs to provide a sustainable economic base for the region. It should be noted that York region has been designated as one of the key growth centers by the province of Ontario, aimed in part to meet the housing and employment needs of Canada?s growing population. York Region is a mix of urban and rural areas and is one of the most desirable areas to live in Southern Ontario. York region offers an attractive lifestyle, with its nine municipalities and the amenities created by the many rivers, streams and protected greenbelt areas that encompass more than 69 per cent of the region?s area.

Jan 1, 2010

By E. H. Cho, B. Conner

Three sulfide minerals, chalcopyrite, sphalerite, and pyrite, were leached using a bioleaching mode and an electrobioleaching mode. The former mode was used to leach the minerals with the bacterium A. ferrooxidans in a bioreactor. In the latter mode, the leaching of the minerals was performed in a combination of a bioreactor and an electrochemical cell. In this set-up, the solution was circulated between the bioreactor and the cathode compartment, the two reactors were in series, and the cell was operated intermittently. The mechanism is such that an increase in Fe(II) concentration, which is a nutrient of the bacteria, by electrochemical reduction of Fe(III) would increase the bacterial population and in turn would accelerate the leaching of the mineral. It has been found that the electrobioleaching of chalcopyrite is an improvement over the bioleaching with respect to the fact that leaching conversion is higher and a high level of Fe(II) concentration can be maintained. However, the electrobioleaching of sphalerite does not show any improvement over bioleaching. The electrobioleaching of pyrite is similar to that of chalcopyrite, and this has potential to be used in applications such as coal desulfurization and pretreatment of refractory gold ore in heap leaching where fine gold particles are entrapped inside pyrite particles.

Jan 1, 2006

By Efstratios Karampinos, John Hadjigeorgiou, Philippe Morissette

"Ground support is a critical element in maintaining the stability of mining drives in deep and high stress mines. In challenging ground conditions, it is necessary to continuously explore ground support strategies that can control the resulting large deformations. It is an objective of mining operations to optimize the ground support by selecting appropriate systems at the time of installation of each reinforcement element. A successful ground support strategy will result in the use of a system that ensures both the structural and operational integrity of the excavations and mitigates the need for rehabilitation.Preliminary ground support design is often based on empirical observations and methods. Once a design is implemented, field trials, observations and in situ pull tests are used to fine tune or improve the design. Although not often employed during this process, numerical modelling can provide helpful insights into the impact of different ground support strategies. In this respect, it is possible to explore the use of multiple options before selecting the most promising ground support system for implementation in field trials. The challenges associated with the numerical modelling of rock support for mines have been described by Lorig and Varona (2013) and Potvin (2017). The employed numerical models should capture all potential failure modes of reinforcement throughout the mining sequence of the excavation. In particular, it is important to emulate the observed in situ ground support performance, as well as the influence of the installation sequence of the support. However, the time and expertise required for this type of modelling of ground support is often not available at mine sites. Even when the expertise is available, it requires a major time commitment and commitment of resources to set up, run and calibrate the sophisticated models capable of explicitly capturing the behavior of ground support.Rock reinforcement is an integral part of all ground support systems used in underground mines. Long, flexible tendons can reinforce the rock mass deeper into the walls and create a thicker reinforced shell around the underground excavation. This article focuses on the optimization of the cable-bolting strategy in squeezing conditions at the LaRonde Mine in Quebec, Canada by integrating the 3D distinct element method (DEM) in the design process. A calibrated numerical model is used to investigate a series of cable bolt configurations and provide recommendations for the ground support design."

Jan 4, 2018

By W. L. Jacobsen, T. L. Dyer

Cortez Gold Mines completed a feasibility study for a new openpit gold mine in north central Nevada. The production schedule calls for a peak in material movement. This schedule is based on current operational efficiencies and equipment parameters observed at the company’s existing openpit operation. To mitigate risks of over/under predicting production, simulation modeling was used to validate the loading and haulage requirements during the peak production period. The advantage of simulation is the ability to provide a realistic model of a mining operation based on scheduled and unscheduled random events during the period under analysis.

Jan 1, 2007

By N. O. Lotter

The reliability of a set of flotation results is key to minimizing project risk either at concentrator commissioning, or at the point of implementing an improvement to an existing concentrator operation. High-Confidence Flotation Testing was developed for this purpose, and is part of the list of technologies of various scales used by Xstrata Process Support (XPS) in addressing these projects. The methodology is based on two principles: one, to ensure that the ore sample is representative and has been well-blended and subsampled; two, to perform the flotation tests in sufficient numbers of replicates with appropriate quality controls, so as to improve the reproducibility of the test data. Across ten years of practice and continuous improvement with this methodology at Xstrata Process Support, Sudbury, several improvements to this method and complementary connections into sampling and quantitative mineralogy have been developed. Two case studies are reviewed. These show the capability of this system in both optimizing an existing concentrator operation and in serving a new mine scenario. Further work to improve the efficiency of this procedure has been identified.

Jan 1, 2009