Search Documents

By John Hardy

The performance of five dense-medium washers was evaluated in four preparation plants. Three of the plants were making a two-product separation that produced a clean coal and a refuse; one plant employed dense-medium vessels in series to effect a primary and a secondary separation. The secondary drum-type washer produced a low-ash metallurgical coal and an intermediate-ash product suitable for plant fuel or steam generation. The sharpness-of-separation was excellent for all four primary separations and the secondary separation.

Jan 1, 1966

By G. L. Ploetz

The lanthanon compounds are becoming increasingly more important for ceramic and allied applications. As the supply increases and the cost decreases, further development of these interesting materials will undoubtedly lead to new applications and an increased demand. Recent improvements in separation processes have lead to high purity in the individual lanthanon oxides. This report includes short discussions on the mineralogy of the ores as raw materials, and on the separation processes required to produce the pure individual lanthanon oxides in useful quantities. To discuss the presently known applications of lanthanon oxides, this general review is divided into the following categories: A. Glasses, Glazes, and Porcelain Enamels. B. Refractories and Abrasives. C. Electronic Ceramics. D. Nuclear Ceramics.

Jan 1, 1960

By Ihsan Berk Tulu, Gaobo Zhao, Deniz Tuncay, Syd S. Peng

Longwall mine instrumentation for measuring abutment stress distribution, mining induced immediate roof stress change and deformation, and primary/secondary support loads and deformations provides critical guidance for the design of gateroad chain pillars and roof support. Field measurement results are also recognized as the best way to calibrate numerical models that have been used to study the failure and support mechanisms. International Conference on Ground Control in Mining (ICGCM) started in 1981 and since then, there were 26 papers published in the proceedings discussing the stress and load measurements as the face advanced using various field instrumentation techniques. The focus of this paper is on summarizing the analyses of the data published in these papers. Stress/load change monitoring included the following categories: gateroad chain pillar, abutment pressure, bolt load, and pre-driven recovery room. The data shows that the magnitude of stress changes as the face advances varies considerably from panel to panel and mine to mine. However, regardless of types of stress changes, pillar stress, abutment pressure, and bolt load, there exists a rough trend of stress increase as the face advances, generally consisting of three stages, i.e., stress/load (1) initially increases steady or slowly, (2) increases rapidly, and (3) increases reaching the peaks and dropping down slowly or sharply. The stress/load increases start earlier during the second panel mining and are larger than the first panel mining. This review makes it easy for the interested persons to find valuable data for other similar projects.

By E. -R. Niinikoski, M. A. Islam, H. Mischo, G. Barakos, J. Joutsenvaara, G. Meissner

European Union's transition to a low-carbon and digital economy highly depends on securing the strategic autonomy of the Critical Raw Materials (CRMs) supply chain. This paper introduces a European Commission-funded research and innovation action, AGEMERA, which aims to create detailed geological and people's concerns maps to unlock the CRMs potential in Europe. Furthermore, the project will develop educational packages for schools and universities, publish online CRM-related games and news flashes, and arrange public events to ensure a basis for socially accepted and sustainable exploration and mining of CRMs in Europe. 1. IntroductionCritical Raw Materials (CRMs), crucial for shifting to a low-carbon and digital economy, should focus on maintaining Europe's overall supply-demand balance (Birol, 2022). Therefore, to proactively address the surge in demand and ensure the strategic autonomy of European industrial supply chains, the exploration and extraction of CRMs must be scaled out across the continent. Moreover, mobilizing Europe's domestic potential is vital for the EU to become more resilient and to establish open strategic autonomy as the demand for CRMs continues to increase quickly on a global scale (European Commission, 2021). Base metal extraction and mining have a long history in Europe. Nevertheless, CRMs mining projects have shown less success, although these have a lot of potential (Guzik et al., 2021). The main barriers are a lack of investment in mining and exploration, complicated and drawn-out national permitting processes, and low levels of public support (European Commission, 2020). It is necessary to have a vast amount of knowledge and intelligence about CRM's potential and market impact. Novel non-invasive geophysical survey techniques that enable sustainable exploration must be created and used to enhance mineral system models of ore deposits incorporating CRMs. The minerals policy framework significantly influences the mining industry's performance, stability, and sustainability. However, the EU Member States' mineral policy frameworks differ significantly (MINLEX, 2017). In addition, the Fraser Institute Annual Survey of Mining Companies offers concrete information on how managers and executives of mining companies view key policy areas that impact mining activities in the jurisdiction in which they operate or are familiar (Jackson & Green, 2015).

Feb 1, 2023

By R. Benito

This paper describes the development of a life-of-mine schedule (LOM) for one of the world's largest known sedimentary copper-cobalt districts located in the Katanga Province, Democratic Republic of Congo (DRC). A particular feature of the Tenke Fungurume LOM schedule is the considerable number of pits/phases for scheduling, each competing to provide the best ore available to a capacity-constrained process facility. This paper discusses the LOM scheduling objectives and constraints, data preprocessing steps such as ore binning, block aggregation and clustering analysis as a scheduling aid, the mine scheduling approach and results and conclusions. Mining Engineering, 2011, Vol. 63, No. 8, pp. 39-47. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By T. A. de Almeida, M. de Paiva Bueno, M. Powell

The mining industry is one of the foundations of modern society, providing not only the raw materials needed to maintain a contemporary lifestyle, but also serving as a basis for the development of future technologies. From the most basic components of an appliance to the materials needed to design an electric car or a space rocket, each raw material has gone through a painstaking procedure of extraction and processing, and ways to make this process more efficient will be of great help to meet an ever-increasing demand for minerals. One of the biggest challenges when extracting mineral resources is to measure the variability of the mineral body prior to processing. Comminution is the most power-demanding stage, and the lack of geometallurgical testing, often for financial reasons, may result in an inefficient operation. The Geopyörä Rock Breakage test was developed with the objective of making mineral variability data more accessible by providing both standard comminution parameters and rock mechanical properties at low cost, and with a modest sample size, allowing a larger number of samples to be tested to reduce uncertainties and assure productivity. The objective of this paper is to present the results of an extensive validation of this new rock breakage method against two of the main tests currently in use, namely the SMC® and Bond ball mill work index tests. More than 100 samples have been tested and the results compared, showing that the new method can accurately estimate the parameters of the traditional tests. This confirms that the new test is a reliable tool for comminution and geometallurgical tests.

Feb 1, 2023

By P. G. Semple

For the last four years, the Kilborn Group of Companies has been involved in several major projects in the Confederation of Independent States (CIS). These include the Kumtor project, the Kubaka gold project, the Kazgold project, the Aginskoe project and the Jerooy project. These projects are all in various stages of detailed engineering and construction. Western mining companies are pursuing mining opportunities throughout the world in search of ore bodies for development. The quest for profitable mining ventures has led mining companies to South America and Asia and, more recently, to the former Soviet Union. When considering the CIS, several factors should be considered. The most notable are geography, mining culture and previous mining production.

Jan 1, 1996

By Savita Schlesinger, Mike Hanna, Nathan Scalla, James O’Shaughnessy, Steve Miller

Loudoun Water’s Quarry A (Milestone Reservoir) project involves conversion of a rock quarry to a billion-gallon raw water reservoir. The project includes a new 40 MGD pump station, deep intake shaft, and three drill and blast intake tunnels for accessing the reservoir. Due to concerns regarding constructability and construction risks, the project design was paused while a Construction Manager At-Risk (CMAR) contractor was procured. The CMAR contractor was engaged collaboratively with the design team to provide risk and constructability input for refining the design. Aspects of the original design, design modifications, and benefits of the CMAR collaboration will be presented.

Jun 13, 2023

By Douglas R. Shaw

Normal dodecyl mercaptan was evaluated as a collector for flotation of sulfide minerals and precious metals. The reagent is from the class of normal mercaptoalkanes (n-alkyl thiols), and is commercially available in the form of a mixture of n-dodecyl mercaptan and a dispersant, under the trade name Pennfloat(TM)3. Reported are results of bench-scale flotation experiments on many commercially treated base metal and precious metal sulfide ores. Dosages, points of addition, and flotation pH were among the uariables studied. Most notable results were increased copper, molybdenum, and precious metals recoveries. Dosages of dodecyl mercaptan on some ores were considerably lower than required for conventional collectors.

Jan 1, 1979

By J. B. Malcolm

The discovery of tungsten-bearing quartz outcroppings in Vance County, N. C., by the Hamme brothers in 1942, made international news in the mining industry and was, in fact, one of the major ore discoveries made in the U.S. during the last 25 years. Operations began at the Hamme mine in 1942, but after 16 years of successful operation, the mine was closed down in 1958 under adverse market conditions. By that time, it had produced nearly 20 million lbs of metallic tungsten. Because of the square-set timber mining method then in use, mine operating expenses were high, actually representing 78% of the total operating expenses at the property. In timber work alone, 160 men were employed. Approximately 500,000 bd ft of timber were placed monthly at a direct supply cost of $1.00 per ton of ore mined. Late in 1959, following a slightly improved position in the tungsten market, company management decided that, by changing the mining method, the operation could be economically feasible. The major premise in this decision was that a reduction of from 25 to 30% of the mining costs could be achieved by the conversion of the mining method from square-sets to horizontal cut and fill. Reopening of the mine began in February 1960, Full production has now been reached and overall mine productivity has been doubled.

Jan 1, 1962

By R. Hogg

Experimental studies of the axial distribution of particles along dry ball mills are described. The results, for mills ranging in diameter from about 10 cm to 1 meter and operated in both the batch and continuous modes, indicate a consistent pattern of significant migration of particles away from the ends of the mill. In some, but less frequent, cases axial migration of the grinding media is also observed. Analysis of the data suggests that particle migration results from end-effects which extend for a distance of about one mill diameter along its length. End-wall roughness appears to play a significant role in the particle migration phenomenon. Media migration is generally associated with continuous mills operating at relatively high powder flow rates.

Jan 1, 1994

By T. M. Yegulalp

A new explanation of the scale dependency of the strength properties of rock is presented based on the theory of extremes. A review of past work on specimen size strength relationship is followed by an introduction to the fundamentals of the underlying theory of extremes and its relationship to the scale effect on the statistical properties of the strength distribution. It is shown that the weakest link theory is directly related to extremal statistics and properties of strength distributions of rock can be derived as a function of the specimen size. Three sets of Brazilian test data are used to demonstrate the use of this approach.

Jan 1, 1992

By S. Gaillard, E. Cauda

"Diesel particulate matter (DPM) is an occupational health hazard in underground mines. It generally occurs in the submicron range, and is often present in the mine atmosphere with significant concentrations of dust particles that tend to occur in the supramicron range. Since dust can interfere with analytical methods to measure DPM, it is often removed from a sample stream using impactor-type size selector (diesel particulate matter impactor, DPMI). Because the DPMI physically removes oversized particles from the stream, its performance may be gradually reduced with aging. Sharp-cut cyclones (SCCs) represent an alternative size selector for DPM sampling applications, with a major advantage being that, by design, they should not be susceptible to rapid aging. This paper presents results of a field study designed to compare the performance of aged versus new/clean DPMIs and SCCs in an underground mine. DPMI aging resulted in clogging of the device, and eventually a reduction of its effective particle cut size – though, when sample flow rate was maintained, DPM sample mass collection was not affected until significant aging had occurred. Under the conditions present for this study, effects of SCC aging were observed to be minimal by the end of the study period. INTRODUCTION Submicron particles are increasingly recognized as significant respiratory health hazards (Cantrell and Watts, 1997; Kenny, et al., 2000; Ristovski, et al., 2012). Diesel particulate matter (DPM) represents a major source of submicron particles in both public and occupational environments (Kittleson, 1998; Abdul-Khalek et al., 1998). Due to their work around large equipment in confined spaces, underground miners have some of the highest exposures to DPM (EPA, 2002; Grau et al., 2004). DPM largely consists of solid elemental carbon (EC), commonly known as “soot”, and organic carbon (OC) that may be sorbed to EC particles (Kittleson, 1998; Abdul-Khalek et al., 1998). EC and OC can be measured by thermal-optical methods such as the NIOSH 5040 Standard Method (Birch, 2016), and their sum is referred to as total carbon (TC). While the complex nature of DPM does not allow for its direct measurement, both TC and EC have been accepted as suitable surrogates for monitoring occupational exposures to DPM (Noll et al., 2007 and Birch, 2016)."

Jan 1, 2018

By A. Juganda, F. WILSON, G.E. BOGIN, H. PINHEIRO, N. SANDOVAL, J.F. BRUNE

To evaluate methane explosion hazards in underground longwall coal mines, researchers at the Colorado School of Mines developed a computational fluid dynamics (CFD) model along with a 1/40th-scale, optically accessible, physical model of a longwall mining section. In this project, CFD models assisted in the design of the physical model to ensure specifications were met to accurately represent the scaling physics as well as to assist in narrowing the experimental matrix and identifying key locations for sensor placement to measure velocity, pressure and gas concentrations. This research will help develop strategies for methane monitoring to prevent methane ignitions and explosions in longwall coal operations.

Dec 1, 2022

By Stewart R. Wallace

In the spring of 1959 while visiting the offices of the US Geological Survey (USGS) in the Denver Federal Center, I had a chance encounter with Paul Theobold, a former but, at that time, casual associate. Paul mentioned to me the results of his work on stream sediment geochemistry (Theobold and Thompson, 1959). Using panned concentrates, Theobold and Thompson had discovered a tungsten anomaly in Clear Creek and followed it upstream to its source on Woods Creek, a small tributary to the West Fork of Clear Creek. The specific source was a debris cone about 0.8 km (0.5 mile) upstream from the mine yard at the Urad molybdenite deposit. Because of the genetic and zonal association of tungsten and molybdenum at Climax, I found this very interesting. Accordingly, I related this information to Robert Henderson, general manager of western operations for Climax, and asked his permission to do some follow-up work. He, in turn, telephoned Frank Coolbaugh, the president of Amax, telling him of my interest and saying that, "Climax would take care of it." On my first visit to Urad, my companions (Dave Jonson, Bruce MacKenzie, and Dick Baker) and I were confronted by a "Cousin Jack" caretaker who made up for his diminutive stature by a "pistolover" that hung down almost to his knee and by a watchdog that was one-half wolf and one-half mean sled dog. We retreated discretely to Clear Creek and then climbed up the "back" side of Red Mountain by separate routes, across the ridge crest, and part of the way down the "front" side, sampling as we went. Although much of the ground was covered with snow, we found lots of puzzling but friendly looking rocks and the geochemical results were interesting. A geologic map of central Colorado showing the location of the Urad-Henderson and Climax deposits is shown in Fig. I.

Jan 1, 1991

By T. J. Close

The Silver Peak Range North Wilderness Study Area was deleted from the list of US Bureau of Land Management lands in Nevada to be considered for wilderness designation. This decision was based in part on the US Bureau of Mines mineral investigation of the wilderness study area which found indications of precious- and base-metal-resources. The study area lies between the Silver Peak and Dyer mining districts of west-central Nevada. The Bureau examined 13 mineralized sites, most of which were previously unknown and unclaimed. These sites are along two zones that cross the study area from the Silver Peak mining district to the Dyer mining district. The two zones transect a volcanic center of fractured and altered rocks that contain epithermal veins of quartz and calcite with gold, silver, and base-metals. At the surface, these veins are poorly defined. Exposures of the more than forty veins examined were as thick as 17 ft and as long as 1000 ft. Samples from these veins contained significant amounts of precious- and base-metals-as much as 0.02 oz per ton gold, 2.1 oz per ton silver, 1.0% copper, 2.6% lead and 0.4 % zinc. No vein large enough or of high enough grade to be classified a mineral resource was disclosed by the sample data. However, most do have indications of precious- and base-metal-resources at depth. Subsurface exploration of some of the veins is recommended.

Jan 1, 1995

By William Gleason

"While the American Exploration & Mining Association (AEMA) was preparing to close one chapter and begin another during its annual conference in Spokane, WA Dec. 3-7, word of a significant victory on an issue that has been important to the association for many years came from the halls of Washington, D.C.During a keynote address on Dec. 6, Joe Balash, assistant secretary of Land and Minerals Management for the U.S. Department of the Interior (DOI), told a sold-out lunch crowd that the DOI had released final drafts of proposed revisions to the Obama-era greater sage grouse conservation plans. The revisions suggest removing hundreds of thousands of acres of federally protected habitat in Utah, and easing restrictions on energy development and other activities, including mining, in Colorado, Idaho and Wyoming.The protections of the sage grouse were put in place by the Obama administration in 2015. The sage grouse, a prairie fowl, is considered by conservationists to be a key indicator species for the health of America’s sagebrush ecosystem. The previous plan to protect the ground-dwelling bird imposed restrictions to development in sage grouse habitat, but did not place the birds on the endangered species list — a move that many believed would have imposed far more rigid rules.AEMA, and its executive director Laura Skaer, led the way in the fight against the Obama-era greater sage grouse plan, arguing that the plan unnecessarily hurt economic development.“We were the first organization to point out that the greater sage grouse was being used to stop mining, oil and gas production and grazing on public lands in the interior mountain west,” said Skaer who is retiring from AEMA with a significant legal win on this front. “Early on, we cautioned that the proposed Land Use Plan Amendments would be worse than a listing (of the sage grouse) under the Endangered Species Act. Very few believed us until they saw the plans with all of the restrictions and the recommendation for a 4-million-ha (10-million-acre) withdrawal from mineral entry. We were the only organization that filed comments on all 88 Land Use Plan Amendments in 11 states covering more than 24.2 million ha (60 million acres).”"

Feb 1, 2019

By J. R. Heberger, B. H. Ngo

The Safety Pays in Mining v2.0 web application, developed by the National Institute for Occupational Safety and Health (NIOSH) Mining Program, helps mines determine the potential costs associated with mining injuries. This web app categorizes injury cost by part of body injured, by the cause of the injury, or by the nature of the injury. When the user selects one of over 150 common types of mining injuries, the app provides information on the distribution of costs of workers’ compensation claims for that type of injury. Based on other user inputs, Safety Pays in Mining v2.0 will estimate the total costs of the selected injuries and the estimated impact of total injury costs on mining company profits and will provide some examples of services and personal protective equipment on which companies could spend the savings that result from the prevention of injuries. This paper reviews the Safety Pays in Mining version 2.0 web application by discussing the development and updates to the app, how it is used to show the true costs of mining injuries, and how mines can benefit from using this app.

Feb 1, 2024

By Michael J. Mujadin

Since the late 60's, planners at American Natural have known that natural gas supplies from traditional sources will be insufficient to maintain a consistently high level of service in the near future. This dwindling of traditional gas reserves will force American Natural and other gas companies to seek new and more exotic sources of supply. In recent years a number of alternative supply sources were considered, including arctic gas, LNG, and SNG based on naptha, LPG and coal feedstocks. Several combinations, all of which included SNG from coal were selected as the most suitable alternative sources of gas supply for American Natural, and thus our company embarked on the formation of a coal gasification project in the early 70's. Work began with the evaluation of available coal supplies in the United States in late 1970. Western North Dakota was selected for several reasons: large contiguous reserves of lignite were available near the surface, similar to German brown coal for which the Lurgi gasification process was originally developed; the conditions for land reclamation in the area are favorable; and the people in the area have a positive attitude toward well ordered development.

Jan 1, 1977

By S. K. Kawatra, J. A. Halt

"Low-grade iron ores are finely ground and processed to recover iron-bearing minerals. However, the iron-rich powder is too fine to be used directly in blast furnaces and most direct reduction furnaces, and must be agglomerated or pelletized into a usable product called “pellets.” Bentonite clay has traditionally been used as a binder to make iron ore concentrate pellets, but it is expensive and contaminates the pellets. Organic binders may be a viable alternative to bentonite clay. This manuscript reviews organic materials that have been used to make iron ore concentrate pellets. Included are discussions on the development of organic binders, common pros and cons to organic binder use, organic binder structure and its effects on agglomeration, and additives to organic binders.IntroductionIron ore agglomeration turns finely disseminated, low-grade iron ores into a usable product, called pellets. During pellet production, fine-grained, iron-rich minerals are liberated from low-grade ores, concentrated, and agglomerated into round balls that are thermally hardened or cold-bonded to form pellets. Pellets are then transported to blast furnaces or direct reduction operations where they are used to produce iron; iron is further refined and shaped into the wide variety of steel-based industrial and consumer products in use today.Over the years, pellet production has become increasingly more prevalent with the increased exploitation of low-grade iron ores and increased iron and steel consumption around the world. In 2010, world iron ore pellet production was 388 Mt. It could be argued that the current pellet production process has been enabled by the use of binders – practical experience has shown that it would be nearly impossible to agglomerate iron ore concentrates using rotary drums and discs without using a binder."

Jan 1, 2015