Search Documents

By Jan M. Mutmansky

Since 1973 when the first edition of the SME Mining Engineering Handbook was published, many significant changes have occurred in the US mining industry. The industry went through a fairly prosperous period immediately after 1973, but then many economic pressures came to bear on mining companies, particularly in the metal and coal branches of the industry. These pressures changed both the mining methods used and the general economics of the mining methods. As a result, the industry today is different in many ways titan it was in 1973. A general summary of some of the more important changes that have come about will be provided here as well as some assessment of the effects of these changes on the choices of mining methods. In the metal mining industry, the most significant trends were increased surface mining, the use of larger and more efficient equipment, and increased technology and automation. The primary impetus for these changes was unprecedented competition from foreign producers. In many cases, this competition came about because of the nationalization of foreign mines and the tendency for these mines to become a source of foreign exchange. Under these circumstances, the mines could be operated even though they were not profitable. As a result, domestic

Jan 1, 2008

By R. A. Jankowski, J. D. Potts

Four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner section averaged 0.59 and 0.26 mg/m3, respectively. The stageloader/crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feederbreaker contributed 0 to 0.2 mg/m3 of dust. A 1000 ft (305 m) increase in belt entry length or a 200 to 500 tons/shift (181,000 to 454,000 kg/shift) increase in production resulted in roughly a 0.1 mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 1992

By Hingant Pierre

The Hurtières Tunnel was built in 1995 with drill and blast method, in metamorphic schist. It is located between Lyon and Torino on the A 43 motorway in the French Alps. During the construction, a geological hazard was encountered, which caused a massive ground collapse. The tunnel was filled up with 3,000 m3of glacial materials. Geological investigations realized after the accident showed that a narrow glacial valley was present at this location the water table was 40 m above the tunnel level. The paper will describe the collapse and the remedial methods which were implemented to proceed through the failure area. These included drainage works,2,000 m3 grouting and 6,200 ml jet grouting columns.

Jan 1, 1999

By F. W. Petersen

Slurry reactors are being used extensively throughout the chemical, biochemical and mineral processing industries. This paper describes the interaction between fine ore particles and granular porous adsorbents such as activated carbon and ion-exchange resins in a stirred tank reactor. Gold and silver cyanides were used as adsorbates to detect changes in the mass transfer characteristics of the adsorbents, which were ashed to determine the loading of ore particles. A simple kinetic model incorporating film diffusion, intrapanicle diffusion ~d the adsorption equilibrium, was used to interpret kinetic data and to estimate the effect of slurry conditions on the diffusion parameters. It was observed that the equilibrium loading of fines in the adsorbents was independent of their concentration in the slurry. Furthermore, the presence of these panicles inside an adsorbent decreases the effective diffusion of gold or silver cyanides into the adsorbent matrix. When fine suspended solids are present in the reactor, a decrease in the effective availability of the superficial surface of the pre-saturated adsorbent panicles for mass transfer from the liquid phase was observed. This newly defined surface availability factor was dependent on the concentration, panicle size, and the zeta potential of the fine particles in suspension.

Jan 1, 1993

By A. F. Agnew

Discussion by A.E Agnew Strachan's paper summarizes a wealth of data on water-storage dam "incidents" published by USCOLD and ASCE in 1988, together with a review of tailings-dam incidents published by USCOLD in 1994. The data is summarized by text and 11 histograms. The histograms present a useful compilation of these data, although the patterns within the histogram blocks did not survive the Mining Engineering printing process - so their usefulness is impaired. Unfortunately, the text discussion is too cursory and does not highlight the significant relationships among the various causes of the incidents. Four paragraphs of text and Fig. 1 were devoted to water-storage dams, but the discussion is too sketchy, and Fig. 1 is unclear. Important statistics that could be uncovered are: •the total number of dam incidents tabulated were 500+, •earth embankments constituted 73% of those in operation and •incidents related to earth embankments were 75%, of which dam failures accounted for 24%, major repairs accounted for 42% and accidents accounted for 34%. Strachan concluded that "the majority of the dam failures are associated with overtopping (p. 49), and that the majority of incidents are associated with spillway and other facility structures" - although this is difficult to discern from Fig. 1. Confusion regarding Strachan's use of the terms "dam failures" and "incidents" is compounded by his use of "failures" and "accidents" in one paragraph of his Introduction section followed by his use of "incidents" in the next paragraph. Getting to the meat of Strachan's important paper, the tailings-dam incident survey (USCOLD, 1994), the connection between Figs 2 through 11 seems obscure. First, in the four paragraphs of introductory material, one learns that "incidents consisted of failures, accidents, seepage and other incidents of performance that did not meet design criteria" (p. 50). One does learn the helpful caveat that "structures not related to mill tailings were not included in the review" - so that the Buffalo Creek (West Virginia in 1972) and Aberfan (Wales in 1966) coal-mine failures, together with the ongoing metal-mine remediation work at Summitville (Colorado) do not muddy the waters of his paper. The all-too-brief discussion of the data shown in Figs. 3 through 11 (185 dams in USCOLD plus 26 dams in UNEP) reveals the following: •Figure 3: 57% of the incidents (failures and accidents) occurred with dams less than 20-m (66-ft) in height. •Figure 4: 63% of the incidents were due to failures alone (subset of Fig. 3). •Figure 5: Active dams had 82% of the accidents and 93% of the failures. •Figure 6: Types of dams (upstream, water-retention, downstream, centerline and "unknown") separated according to incidents. •Figure 7: Breaks out the incidents in Fig. 6 by failures, accidents and ground water. •Figure 8: Breaks out incidents by type (overtopping, slope stability, earthquake, foundation, seepage, structural, erosion, mine subsidence and "unknown"). •Figure 9: Separates Fig. 8 data into active and inactive dams. •Figure 10: Separates Fig. 9 data into failures and accidents. •Figure 11: Same as Fig. 8, but broken out by tailings-dam type (Fig. 6). Figures 6 and 7 show that most of the failures are associated with upstream or "unknown" types. Figure 9 shows that the leading causes of incidents for active dams

Jan 1, 2003

By Jack Bedder

"Editor’s note: We would like to thank those who make this annual issue possible. A special thank you goes out to the industrial minerals annual review editor, to the Industrial Minerals & Aggregates Division Technical Committee chair and vice chairs, and to the authors of the individual commodity profiles.Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor.Ebrahim K. Tarshizi, member SME, of Michigan Tech, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include: • Hyunjung Kim, member SME, of Chonbuk National University, agricultural materials.• Xihui Yin, member SME, of Kemira, ceramics and refractory materials.• Nikhil Gupta, member SME, of Virginia Tech, chemical raw materials.• Jasson Giddens and Swadhin Saurabh, members SME, of Oil Dri Corp of America and Mill Creek Engineering, respectively, chemical raw materials.• Snehamoy Chatterjee, member SME, of the Michigan Tech.• LeDeana Roberts and Shubham Verma, members SME, of Imerys and U.S. Oil Sands, respectively, fillers and pigments.• Thomas Hilderbrand and Kaiwu Huang, members SME, of Thiele Kaolin Co. and Virginia Tech, respectively, sorbents, filters and process aids.• Rhaghav Dubey and Edgar Blanco, members SME, of Outotec and FL Smidth, respectively, specialty mineralsAntimony generally occurs along with gold, lead, copper and silver. There are more than 100 antimony minerals, although the sulfide mineral stibnite is the main one.Antimony enters the supply chain either as a result of mining (primary production) or recycling (secondary production). China has by far the largest antimony resources and is, as a result, the world’s center for antimony mine production. In 2016, it accounted for more than three quarters of the global mine supply out of a world production figure of 130 kt (143,000 st), according to the U.S. Geological Survey. The biggest, and most high-grade deposits are found in southern China, with the largest mines located in Hunan, Guangxi and Yunnan provinces. Tajikistan, Russia, Australia and Bolivia are the largest mine producers outside China. A new antimony project in Oman made progress in 2016, producing first metal in April 2016 in test facilities, and then ordered three furnaces for a 26 kt/a (28,600 stpy) antimony metal and oxide smelter that is due on stream in late 2017.Antimony ingot production is not as widespread as is antimony mine production, owing to the high levels of pollution that are associated with antimony smelting. It is for this reason that smelting has been largely confined to China and other Asian countries, where environmental legislation is less stringent.Antimony oxide production is undertaken on four continents with China being the biggest producer. There is also a considerable amount of oxide production in Europe — which relies on imported feedstock, mostly from China. Antimony also enters the supply chain through recycling. Lead containing antimony is produced in a number of countries, mainly in secondary lead smelters. Typically, a blast furnace charge containing used or discarded battery plates, type metal or bearing metal is reduced to lead bullion, which is refined in reverberatory furnaces and melting pots. In the main, the antimony recovered is consumed in metallurgical applications. China was the biggest secondary antimony producer in 2016, and accounted for 25 retardants and lead-acid batteries. Flame retardants accounted for roughly 50 percent of consumption in 2016 with batteries representing about 25 percent. Other end uses include plastics and heat stabilizers, ceramics and glass and a variety of metallurgical applications. Demand has been sluggish since the global financial crisis, mostly because key markets failed to recover strongly from the downturn, particularly in Europe."

Jan 7, 2017

By David B. Campbell

INTRODUCTION This submission was made to the Royal Commission of Inquiry into uranium mining in British Columbia. It discusses the stability of waste rock piles that might be developed in conjunction with uranium mining and the control of leachates that might be generated within these waste rock piles over the short and the long term. Short term refers to the interval during which a waste rock pile undergoes either continuous, or alternatively intermittent development, and in general can be considered to extend over the operating life of the mine. Long term refers to the postmining period, i.e. after the ore-body has been exhausted, and mining operations have ceased. Two major classes of waste material are generated in the course of mining and milling operations. Tails, which are the solid waste materials produced by the milling operations commonly exit the mill in slurry form and are stored in tailing retention ponds. Management and control of these slurried wastes are the subject of other papers to the Commission and this conference. In the course of the mining operations, it may be necessary to remove rock materials that are below cut-off grade. That is, ore concentrations within some of the mined rock may be lower than the concentrations which on the basis of economic considerations justifies milling the material. Rock which is removed in the course of the mining operations, but which is below cut-off grade is referred to as waste rock. This waste rock is commonly consigned to a specific area for disposal where it is placed in a mound or pile, i.e. a waste rock pile. Ore concentrations within the waste rock may vary from zero to just below cut-off grade. Since an increase in the market value of uranium could at some time in future result in reduction of the cut-off grade, it follows that waste rock containing ore concentrations slightly below today's cut-off grade could become ore grade rock at some time in future. For this reason, the mine operators may deem it advisable to separate waste rock according to grade, and to consign the waste rock to two or more individual waste rock piles. For purposes of clarity and simplicity, this submission treats the stability of waste rock piles and leachate control in a manner which assumes that these potential problems are isolated and separate from other aspects of the mining and milling operations. For many site specific cases, the problem of potential leachate control might be integrated with the tailings management aspect of the project, thereby realizing economic benefits while at the same time reducing the potential for adverse environmental impact.

Jan 1, 1980

By J. J. Gusek

The Riley Pass strip mine is an abandoned uranium-bearing lignite deposit in Harding County, South Dakota, covering about 150 acres of highwalls, pit floor and mine spoils exhibiting elevated levels of radioactivity. Six reclamation design alternatives were developed, ranging from doing nothing to reclaiming to approximate original con-tour. The alternatives were evaluated for expense, site stabilization, and mitigation of public safety hazards. A comparative economic evaluation on three of the alternatives was completed for the Forest Service in selecting an alternative and substantiating federal funding requests. This evaluation included economic impacts associated with physical and radiologic health hazards, affects on recreational users, socioeconomic impacts and environmental improvement.

Jan 1, 1995

By Janet Briggs, Michael Vertes, J. F. Shirley, R. E. Cutherbertson, Alexander Sutulov, J. D. Vincent

Molybdenum, the 42nd element in the periodic table, is now a very important metal in industry of the United States and the world. Chemically, it is a very complex element having valences of 0, +2, +3, +4, +5, and +6, and can exist as a mixture of these valences in many compounds. It was discovered and separated by Scheele in 1778. At the present time, molybdenite is the only important commercial source of molybdenum. Molybdenum occurs in some 12-14 different recognized minerals, but practically all of the production is molybde¬nite. As late as 1915, it was considered a rare metal. Germany made extensive use of it during the first world war, which resulted in the establishment of a molybdenum industry in the United States at Cli¬max, Colo., in 1917. It was not until the mid-1920s when its introduc¬tion to steelmaking developed for the US automobile industry that the metal gained important acceptance. The first notable example was the Willis-Saint Claire automobile introduced in 1921 by C. Harold Willis, formerly chief metallurgist for Ford Motor Co. Molybdenum has also been produced in the US from wulfenite (PbMoO4) from Arizona and Nevada, and a small amount of molyb¬denite was produced up to the early 1970s as a coproduct from two molybdenum-bismuth mines in Quebec, Canada. The first byproduct production of molybdenite from a copper con¬centrating operation was achieved at Cananea, Sonora, Mexico, and was followed shortly by the Utah division of Kennecott Copper Co. in the mid-1930s. This section of the Handbook is divided into four main subdivi¬sions: Chapter 2, which deals with the concentration and recovery of molybdenite from primary molybdenum ores; Chapter 3, which deals with the recovery and separation of molybdenite as a byproduct from copper production; Chapter 4, which deals with the conversion practices employed for converting molybdenite to the oxide or metal form; and Chapter 5, which covers the uses of molybdenum in steel¬making, chemicals, pigments, lubrication, catalysts, etc. The Free World molybdenum production, for the past eight years from all sources, is shown in Table 1. 2. Primary Molybdenite Ores General In 1978 there were four primary molybdenite recovery plants in operation: Climax, Endako, Quests, and Henderson. For over half a century the Climax mine has been by far the largest and most important source of molybdenum in the world. During the early 1970s a few primary molybdenite mines in British Columbia were shut down due to adverse economical conditions. The largest of these was British Columbia Molybdenum, formerly owned by Kennecott Copper Corp. The Climax plant and operations are described in detail and the opera¬tions of the other plants are summarized following a general discussion of recovering molybdenite from primarily molybdenite ores. Recovery of molybdenite as a byproduct will be taken up in Chapter 3. Geology Molybdenite production from mines in which it is the sole or preponderantly important mineral is confined to ore bodies in granites or igneous-type rocks or pegmatite dikes. More than one state of mineralization is sometimes present as at Climax, York, Hardy, and Questa. In the case of Climax, important byproduct recovery of tung¬sten, tin, pyrite, and monazite is also attained. The molybdenite is commonly disseminated very finely in the siliceous granitic gangue but does occur in stringers and blebs in silicified mineral solution channels. Treatment of Primary Molybdenum Ores All primary molybdenum ores are low in molybdenite, the content ranging from less than 0.20% MoS2 to a high of about 0.40% MoS2. A high resistance to grinding is a common ore characteristic combined with a habit of very fine dissemination of molybdenite in the siliceous portion of the ore. Because of low MoS2 content, high hardness, and fine dissemination of molybdenite in primary ores, it has been necessary to develop a special mill treatment which yields an accepta¬ble recovery at a reasonably low milling cost. Essentially, the treatment consists of intensive rougher flotation at a relatively coarse grind with production of a low grade rougher froth containing a substantial percentage of the molybdenite in the form of low grade middling particles, followed with multistage regrinding to liberate the locked molybdenite and several stages of flotation cleaning to produce a finished grade concentrate. Rougher flotation on pulp ground to ap¬proximately 35 mesh is common practice, even if complete liberation of molybdenite from siliceous gangue may require regrinding to 200 mesh. The flotation of middling particles with a very low content of molybdenite in the rougher flotation step has been made possible by the application of a combination of reagents first developed at the Climax mill and used with some modification in the treatment of all primary molybdenum ores. The reagents commonly employed and their functions in flotation are:

Jan 1, 1985

By Stephen J. Swan

Feed-forward control (i.e. the forward flow of information in a control system ) is a simple and flexible approach to over-all control of a ball mill-rake classifier grinding circuit. The system described here uses mill power, feed rate, mill dilution water flow rate, and classifier dilution water flow rate only, to control mill load, throughput, mill solids, and classifier solids as well as classifier overflow grind. The mill load is controlled by a simple feed-back control loop, while mill solids and overflow grind are controlled within close limits by a unique non-linear feed-forward water control system. In effect the control follows a limited mathematical model of the grinding circuit. The configuration minimizes deviations in overflow grind due to changing ore conditions, but since it is open-loop, and the model is not complete, it is affected by changes in total ball charge and liner wear. These effects are fortunately gradual, and changes in the grind can usually be kept to within ± 1% of a target continuously for several days without adjustment. Control adjustments are made with feed-back from laboratory composites. This control system has won enthusiastic operator acceptance; it is easily started up and shut down; grind-outs have been eliminated along with flotation machine flooding and mill spills. Standard measurements and components are used throughout providing a trouble-free system design at a moderate cost.

Jan 1, 1970

By V. E. May

Has your organization adopted Six Sigma as part of their Performance Improvement strategy? What about Lean manufacturing or Lean Six Sigma? If you already have any of these business process improvements in place where will you go next? In this article we will focus on transforming your organization beyond Lean Six Sigma to the next level of performance. In the future companies can take another quantum step forward by combining Lean Six Sigma with advanced Root Cause Analysis (RCA). The value of taking this natural progression on the way to achieving new levels of organizational excellence is presented.

Jan 1, 2011

By B. K. Cantrell

The use of diesel equipment in underground coal mines is controversial because "whole diesel exhaust" is regarded as "a potential occupational carcinogen" by the National Institute for Occupational Safety and Health (NIOSH). Threshold limit values (TLVs) are recommended for the gaseous pollutants; CO, CO2, NO, NO2, SO2' and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols. The University of Minnesota and the Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines using diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality.

Jan 1, 1991

By Denis Tepavac, Mark Trim

Structural performance of fiber reinforced concrete (FRC) depends on its ability to carry tensile forces after cracking. Australian Standards AS5100-2017 and AS3600-2018 are the only available design standards that establish a test procedure to determine strength and toughness of an FRC in direct tension. Direct tensile testing of fiber reinforced shotcrete samples was performed to determine if the model and guidelines in AS5100/3600 were applicable to shotcrete; all previous testing was from cast samples. In addition to direct testing, micro CT-scanning was also performed. The paper presents tests performed, results, and how the tests could be used on future projects. In addition, a brief summary is provided of the guiding structural mechanics used for estimating residual tensile strength and test methods utilized to verify those estimates.

Jun 13, 2023

By Barbara S. Parrish, I. S. Parrish

For two consecutive years the author and his wife have been fortunate enough to have been invited by the Peoples Republic of China to work with Chinese geologists of the Geological Bureau of the Ministry of Metallurgical Industries (MMI). Our visits, each of which lasted 7-8 weeks, took us to northwestern Sichuan, central Anhui, and much of Hebei Province, as shown in the accompanying drawing. We were asked to evaluate, criticize, and offer suggestions on the exploration and mining techniques used by the Chinese. Our commission both years was centered on gold, although we were also to visit other operations when the opportunity arose. In 1986, the visit primarily concerned with disseminated "Carlin" type gold deposits; in 1987, with "Greenstone" type gold deposits. Gold has been targeted by the Chinese as a metal of importance to the nation. Several governmental agencies have received direction and budgets to seek and develop gold properties. Besides the Ministry of Metallurgical Industry, gold is being sought by the Ministry of Geology, the China Gold Corporation, and reportedly the Peoples Army. There is considerable competition among these agencies. It is not uncommon to find two or more agencies working in the same general area. However, communication between the groups is minimal. Last year, we toured a small mine at Bambishan. We could see a diamond drill across the valley. The rig belonged to another Ministry and my guides voiced their curiosity to know what their competitors were finding. Mining, too, is not the monolithic bureaucracy that most Westerners anticipate in China. There are various levels of mining. These differ not only in sophistication, but in ownership. First, for small deposits the state allows "Peoples Mines". These can be owned and worked by individuals. The individual owner-miner may hire relatives or neighbors and give them a wage or he may turn the mine into a joint ownership situation. They

Jan 7, 1988

By Richard L. Gordon, William A. Vogely

ENERGY POI.ICY-PRINCIPLES AND THEIR PRACTICE Persistently, at least since the end of World War 11, governments have intervened broadly, deeply, and incoherently in major energy markets. If we take a broad definition of energy that encompasses gas distribution and electric power, we can observe regulations of even older vintage. This trend, of course, is not unique to energy. Expansion of government controls has occurred in many areas. The relevant basic question about energy regulation, therefore, is not why is energy special, but whether any general principles exist to explain the wisdom of existing regulations. This review takes place at a time, the middle 1980s, in which a massive onslaught is being undertaken against government regulation. However, the present chapter is influenced primarily by my observations of the failures of energy regulations and not by any inspiration from those ideologically opposed to government intervention. Several subquestions arise in policy appraisal. A primary need is to establish clear objectives and determine the consistency between these goals and the policies imposed. Thus, the first step is to set objectives. The next is to outline ways to attain these goals. However, it should be recognized that many apparently distinct options are economically equivalent. When the goal is to charge producers or consumers for something, it is possible to attain the same result through either government ownership or taxing private transactions. The tax can raise the price to the level the government would have charged if it were the owner. Creation of a Department of Energy is not necessarily any different from having separate energy agencies well coordinated by some small supervisory body. Thus, a distinction should be made between substance and form in policymaking. The critical substance concerns such matters as whether the government imposes financial penalties, incentives, or rules to attain a goal. Then, there can be many equivalent ways to implement the basic policy form. The second prior illustration suggests that one favorite question is how to attain proper integration of policy. At various times, voices on either (or even both) sides of the Atlantic have called for a coordinated energy policy. The U.S. Paley Commission made this a primary goal for future policy. The western European governments that were the founding members of the Coal and Steel, Economic, and Atomic Energy Communities spent much time in the middle fifties and much of the sixties trying futilely to agree on an energy policy. (See Gordon, 1970 for an annotated review). The energy price rises of the 1970s rekindled United States interest in coordination. However, astute observers of the problem such as O. C. Herfindahl of the United States and Maurice Allais (1 962) in France warned the discussions confused form with substance. The crucial issues were what were the goals and what were the best types of policies to attain such goals. Policy suffered, not from poor organization, but from discord about the goals and how to attain them. All this suggests that we need principles to guide policy appraisal. The branch of economic theory known as welfare economics concentrates on providing guidance about the problems of policymaking. The theory examines both what

Jan 1, 1985

By Aidan Giblett

"It is important to make a clear distinction on the scope of work of the Global Mining Standards and Guidelines (GMSG) guideline for sampling grinding circuits. Many mineral processing practitioners are familiar with the sampling and surveying of comminution circuits, in particular grinding circuits, for performance diagnosis and the identification of optimization potential. These surveys often provide information for population balance modelling of individual comminution and classification unit processes, and consequently require a large amount of information to calibrate and validate the unit models. As a result, these surveys are labour intensive, somewhat expensive, depending on internal capabilities of the mine site or company and have a long time span from initial planning to final reporting. They also require a high level of expertise to process the survey data, simulate the circuit and make sensible recommendations on follow up actions.As a result of these factors, full grinding circuit surveys are not a common occurrence at a large number of processing facilities, and several years may pass before follow up surveys are conducted. In the ensuing gap between surveys, the efficiency of the grinding circuit must often be taken on faith, and this is considered an unacceptable lapse in an environment of strained natural resources and low commodity prices.To support the rapid and productive energy efficiency analysis being promoted by the ICE working group, a much simplified survey and analysis process is required. The process reflected in the GMSG guideline is indeed more conducive to frequent analysis, at a skill level that is well within the capabilities of the average plant metallurgist. As a result, it becomes feasible to conduct mini-surveys of plant performance, which can be used to quickly and precisely diagnose the high level impact of process changes. These methods can also be manipulated by an experienced practitioner to provide sufficient information for modelling of the circuit to estimate the impact of process changes, allowing an initial rate and rank exercise to focus plant optimization efforts."

Jan 1, 2015

By Bobby G. Cahoon

The ( ) Tayaaja ( ) . The deposit ( ) 130 kilometers due east of the continental divide and approximately 290 kilometers east-southeast of Lima (Figure 1). Relief in the immediate vicinity of the mine, which lies or the west side of the Mantaro river, is in excess of 2,000 meters, and the elevation varies from a low of 2,000 meters above sea level on the Mantaro River to a high of 4,386 meters at point T-27 (Figure 2). Although the Cobriza deposit was first reported by the Italian Geographer Antonio Raimondi in 1866, only three reports have been published on the deposit, which began production in 1966 (Duefias, 1908; Fernandez Concha and Garcia y Garcia, 1961; Petersen. 1965). Many private reports have, however, been written by geologists employed by the Cerro de Pasco Corporation. These reports and the author's observations, while employed as the Cobriza Division Mine Geologists form the basis of the present paper, which describes the relations between-the ore controls in the Cobriza mine and the regional and local structure.

Jan 1, 1971

By Robert L. (Original by) Llewellyn

Many of the problems that occur in the preparation plant originate from practices in the mine. Impurities in raw coal can be in the seam itself or from extraneous material taken in mining from the roof or bottom. In the case of underground mines, the choice of mining equipment will affect the size consist and the amount of extraneous material included with the coal. Also, governmental regulations concerning the degree of rock dusting, gobbing underground, and cleanup have increased the dirt in raw coal. Sulfur dioxide emission standards, on the other hand, are pressuring the coal industry to clean coal more thoroughly. Coal supplied for coking purposes is nearly all upgraded by washing, while for the largest market, electric power generation, a high proportion is shipped as a raw product with processing, in whole or in part, only necessary when excess impurities are mined with the coal. This chapter will deal primarily with plants that process or wash coal to some extent (Fig. 1) and only incidentally with mines shipping raw run-of-mine coal crushed to a top size of, usually, 51 to 102 mm (2 to 4 in.), with little, if any, other treatment.

Jan 1, 1981

By Dennis N. Poffenroth

One concern of the Mine Safety and Health Administration is the structural integrity of steel wire ropes used on mine personnel hoists and elevators. Failure of such ropes has resulted in loss of life and property. Although thorough and regular visual examinations are performed, hoist ropes may still fail from undetected internal wear, corrosion, and broken wires. To complement visual examinations, nondestructive rope inspection techniques have been developed to determine deterioration and removal criteria. The techniques use electromagnetic and permanent-magnet test instruments designed by a Canadian firm. This paper describes the operating principles, field and laboratory testing of these nondestructive testing instruments, and discusses the feasibility of using this type of testing as a supplement to visual examination and destructive tests.

Jan 1, 1983

By J. W. Leonard, C. L. Jiang, B. K. Parekh, X. H. Wang

The selective depression of pyrite from the Kentucky No. 9 coal seam was systematically examined using various kinds of inorganic and organic chemicals. Most of the organic chemicals tested showed little selectivity in pyrite depression. It was found that both orthophosphate and pyrophosphate were effective for the selective depression of coal pyrite in coal flotation using fuel oil as a collector. At substantially low concentrations of pyrophosphate, the flotation of coal pyrite was completely depressed over a wide pH range, while the coal flotation remained unaffected. The mechanism of the selective depression of pyrite by phosphates was explained with the help of thermodynamic calculations of iron-phosphate-water systems and zeta-potential measurements. It was shown that pyrophosphate reacts strongly with the iron ions of pyrite to form stable hydrophilic iron pyrophosphate complexes on pyrite surfaces.

Jan 1, 1999